SEARCH · Search NASA

Results for “Surface Modification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

All sources NASA NTRS DOE OSTI

NASA NTRS1989

A free surface vortex method with weak viscous effects

The advantage of vortex methods for inviscid flows of several fluids separated by interfaces is that problems of this kind may be posed and solved numerically entirely on the interface surface. For free surface problems, where one of the fluids has negligible inertia, a small amount of viscosity produces a thin, weak rotational layer adjacent to the potential flow vortex sheet. Here, a method is described for including this weak viscous effect as a modification of the boundary conditions for the potential part of the flow, thus allowing this slightly viscous flow to be formulated as a vortex method on the free surface. This is important for unsupported free drops where the viscosity at the free surface is the only source of damping for oscillations, and for gas-filled bubbles, where it provides both drag and damping. Small applied shear stresses from aerodynamic, electrostatic, or other sources may be included provided they are of the same order as the potential flow shear stress or smaller.

Lundgren, T. S.↗

NASA NTRS1998

Stratospheric Sulfuric Acid and Black Carbon Aerosol Measured During POLARIS and its Role in Ozone Chemistry

Stratospheric aerosol can affect the environment in three ways. Sulfuric acid aerosol have been shown to act as sites for the reduction of reactive nitrogen and chlorine and as condensation sites to form Polar Stratospheric Clouds, under very cold conditions, which facilitate ozone depletion. Recently, modeling studies have suggested a link between BCA (Black Carbon Aerosol) and ozone chemistry. These studies suggest that HNO3, NO2, and O3 may be reduced heterogeneously on BCA particles. The ozone reaction converts ozone to oxygen molecules, while HNO3 and NO2 react to form NOx. Finally, a buildup of BCA could reduce the single-scatter albedo of aerosol below a value of 0.98, a critical value that has been postulated to change the effect of stratospheric aerosol from cooling to warming. Correlations between measured BCA amounts and aircraft usage have been reported. Attempts to link BCA to ozone chemistry and other stratospheric processes have been hindered by questions concerning the amount of BCA that exists in the stratosphere, the magnitude of reaction probabilities, and the scarcity of BCA measurements. The Ames Wire Impactors (AWI) participated in POLARIS as part of the complement of experiments on the NASA ER-2. One of our main objectives was to determine the amount of aerosol surface area, particularly BCA, available for reaction with stratospheric constituents and assess if possible, the importance of these reactions. The AWI collects aerosol and BCA particles on thin Palladium wires that are exposed to the ambient air in a controlled manner. The samples are returned to the laboratory for subsequent analysis. The product of the AWI analysis is the size, surface area, and volume distributions, morphology and elemental composition of aerosol and BCA. This paper presents results from our experiments during POLARIS and puts these measurements in the context of POLARIS and other missions in which we have participated. It describes modifications to the AWI data analysis procedures in which the collection of BCA is modeled as a fractal aggregate. The new analysis results in an increase in BCA surface area of approximately 24 and an increase in mass of 7-10 from the previous method. For the current study, BCA surface area is used in computer models that attempt to predict measured NOx/NOy ratios and O3 depletion rates. Inclusion of the HNO3 reaction with BCA in one model tends to improve the agreement of calculated to measured NOx/NOy ratio. However, it was found that these trends are viable only if the reactions are catalytic.

Strawa, Anthony W.↗

DOE OSTI2023

Melamine modification of fuel cell electrodes

A method for forming a melamine-modified electrode that includes providing a metal based electrode and patterning a surface of the metal-based electrode by contacting the electrode with a melamine solution to form a patterned metal-based electrode. The patterned metal-based electrode includes metal sites blocked with melamine molecules and metal sites which are not blocked such that the metal-based electrode selectively adsorbs O2 instead of at least one of sulfate, phosphate, or sulphonate. A range of 20% to 40% of the metal sites are blocked with melamine molecules.

Strmcnik, Dusan↗

DOE OSTI2025

Interface, bulk and surface structure of heteroepitaxial altermagnetic α-MnTe films grown on GaAs(111)

Epitaxial MnTe films have recently seen a surge in research into their altermagnetic semiconducting properties. However, those properties may be extremely sensitive to structural and chemical modifications. We report a detailed investigation of the synthesis of the altermagnet α-MnTe on GaAs(111), which reveals the bulk defect structure of this material, the mechanism by which it releases strain from the underlying substrate, and the impact of oxidation on its surface. X-ray diffraction measurements show that α-MnTe layers with thicknesses spanning 45 to 640 nm acquire lattice parameters different from bulk, mostly due to thermal strain caused by the substrate rather than strain from the lattice mismatch. Through high-resolution transmission electron microscopy (TEM) measurement, we then unveil a misfit dislocation array at the interface, revealing the mechanism by which lattice strain is relaxed. TEM also reveals a stacking fault in the bulk, occurring along a glide plane parallel to the interface. The combination of TEM with polarized neutron reflectometry measurements finally reveals the impact of oxidation on the chemistry of the surface of uncapped MnTe. Furthermore, or findings highlight the subtle role of epitaxy in altering the structure of α-MnTe, providing potential opportunities to tune the altermagnetic properties of this material.

Altermagnets↗

DOE OSTI2020

Changes of Magnetism in a Magnetic Insulator due to Proximity to a Topological Insulator

We report here the modification of magnetism in a magnetic insulator Y 3 Fe 5 O 12 thin film by topological surface states (TSS) in an adjacent topological insulator Bi 2 Se 3 thin film. Ferromagnetic resonance measurements show that the TSS in Bi2Se3 produces a perpendicular magnetic anisotropy, results in a decrease in the gyromagnetic ratio, and enhances the damping in Y 3 Fe 5 O 12 . Such TSS-induced changes become more pronounced as the temperature decreases from 300 to 50 K. These results suggest a completely new approach for control of magnetism in magnetic thin films.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2018

Dynamic Monitoring of the Ion-Plasma Treatment of Complex Components

Low-temperature ion-plasma treatment of metal workpieces may be monitored in terms of the electrical signals recorded in the circuit consisting of the plasma, the workpiece, the clamp, and ground. The electrical signals are analyzed by means of the Hurst statistic H, which provides a basic quantitative picture of the formation and modification of the signal structure in the course of machining. Experiments show that the best results (a surface layer of maximum hardness) are obtained when machining is accompanied by the generation of signals for which the Hurst statistic indicates antipersistent behavior.

42 ENGINEERING↗

NASA NTRS1973

Holographic studies of shock waves within transonic fan rotors

Pulsed laser holographic interferometry has been applied to the detection of shock patterns in the outer span regions of high tip speed transonic rotors. The first holographic approach used ruby laser light reflected from a portion of the centerbody just ahead of the rotor. These holograms showed the bow wave patterns upstream of the rotor and the shock patterns just inside the blade row near the tip. Much of the region of interest was in the shadow of the blade leading edge and could not be visualized. The second holographic approach, on a different rotor, used light transmitted diagonally across the inlet annulus past the centerbody. This approach gave a more extensive view of the region bounded by the blade leading and trailing edges, by the part span shroud and by the blade tip. These holograms showed the passage shock emanating from the blade leading edge and a moderately strong conical shock originating at the intersection of the part span shroud leading edge and the blade suction surface. Reasonable details of the shock patterns were obtained from holograms which were made without extensive rig modifications.

Benser, W. A.↗

NASA NTRS1973

Apollo 17 laser altimeter

The performance and operation of the Apollo 17 laser altimeter after several modifications are discussed. Functions of the instrument include precise altitude measurement of the CSM above the lunar surface, and measurement of broad scale topographic relief around the entire circumference of the moon.

Wollenhaupt, W. R.↗

NASA NTRS1975

Diffusion pump modification promotes self-cleansing and high efficiency

Modifications eliminate contaminant substances from pump fluid during operation, which are principal causes of torpidity on evaporative surface. Diffusion pump is also acting as still. Resulting 100 percent vigorous working surface provides much greater molecular throughput and greatly improved efficiency.

Buggele, A. E.↗

NASA NTRS1979

Phase 2 of the Array Automated Assembly Task for the Low Cost Solar Array Project

Two process specifications supplied by contractors were tested. The aluminum silk screening process resulted in cells comparable to those from sputtered Al. The electroless plating of contacts specification could be used only with extensive modification. Several experiments suggest that there is some degradation of the front junction during the Al back surface field (BSF) fabrication. A revised process sequence was defined which incorporates Al BSF formation. A cost analysis of this process yielded a selling price of $0.75/watt peak in 1980.

Campbell, R. B.↗

NASA NTRS1983

Double layered tailorable advanced blanket insulation

An advanced flexible reusable surface insulation material for future space shuttle flights was investigated. A conventional fly shuttle loom with special modifications to weave an integral double layer triangular core fabric from quartz yarn was used. Two types of insulating material were inserted into the cells of the fabric, and a procedure to accomplish this was developed. The program is follow up of a program in which single layer rectangular cell core fabrics are woven and a single type of insulating material was inserted into the cells.

Falstrup, D.↗

NASA NTRS1984

Application of a full potential method for computation of three-dimensional supersonic flows

A nonlinear aerodynamic analysis technique based on the full potential equation in conservative form has been modified to permit treatment of supersonic flows with embedded subsonic regions (typically near the fuselage-canopy juncture and the wing leading edge). Solution procedures for the equations do not require any specific form of geometry or physical grid system. This results in the capability to analyze easily very complex geometries provided the posed problem lies within the isentropic restrictions of the full potential theory. Characteristic signal propagation theory is used to monitor the type dependent flow and a conservative switching scheme is employed to transition from the supersonic marching algorithm to a subsonic relaxation procedure and vice versa. An implicit approximate factorization scheme is used to solve the finite-difference equations. These modifications now permit analysis of fully three-dimensional flowfields including the interference effects due to lifting surface wakes. Improved grid generation capability allows analysis of complete complex aircraft geometries (fuselage, wing, tail, wing wake, and tail wake). Results are presented showing very good correlations with experimental surface pressure data and aerodynamic force data at both design and off-design operating points. Configurations examined include several waverider concepts, an arrow wing-body with wake, an advanced tactical fighter concept, and a fighter forebody-canard configuration.

Jones, K. M.↗

NASA NTRS1985

Operational life improvement of SSME high-pressure turbopumps

The current Space Shuttle Main Engine (SSME) Phase I engine demonstrated excellent flight performance but showed limited operational life of the high-pressure fuel turbopumps (HPFTP). Design improvements, supporting analyses, and test results of the SSME Phase II development program are presented. The HPFTP improvements include reduction of turbine operating temperature by 110 to 130 R by reconstructing the seals and the flow contours; modifications of the first- and second-stage turbine blades by recontouring the shank, shotpeening the shank surface, and applying a multilayered, plasma-spray coating to the shank on the downstream side to reduce the effect of the disk coolant; and reduction of the tendency for thermal cracks in the turbine by changing weld configuration to avoid the concentration of stresses in local areas. The high-pressure oxidizer turbopump has been also modified to improve bearing life and to eliminate subsynchronous whirl.

Hale, J. R.↗

NASA NTRS1989

Using passive, thermal remote sensing techniques for detecting subsurface gravel accumulations in vegetated, unconsolidated sedimentary terrains

Multiband radiometric data from an airborne imaging thermal scanner are being studied for use in finding buried gravel deposits. The techniques are based on measuring relative differences in the thermal properties between gravel-laden targets and the surrounding gravelless background. These properties are determined from modeling the spectral radiant emittance recorded over both types of surfaces in conjunction with ground measurements of the most significant heat flows above and below the surface. Thermodynamic properties of sampled materials from control sites are determined, and diurnal and annual subsurface heat waves are recorded. Thermal models that account for heat exchange at the surface, as well as varying levels of soil moisture, humidity, and vegetation, are needed for adaptation and modification to simulate the physical and radiative environments of this region.

Burns, Gregory S.↗

NASA NTRS1994

An integrated optical CO2 sensor. Phase 0: Design and fabrication of critical elements

Significant progress has been made toward all of the goals for the first phase of the project short of actual fabrication of a light path. Two alternative approaches to fabricating gold mirrors using the basic LIGA process were developed, one using electroplated solid gold mirrors and the second using gold plated over a nickel base. A new method of fabrication, the transfer mask process, was developed and demonstrated. Analysis of the projected surface roughness and beam divergence effects was completed. With gold surface with low surface roughness scattering losses are expected to be insignificant. Beam divergence due to diffraction will require a modification of the original design, but should be eliminated by fabricating mirrors 1000 mu m in height by 1000 mu m in width and using a source with an initial beam radius greater than 300 mu m. This may eliminate any need for focusing optics. Since the modified design does not affect the mask layout, ordering of the mask and fabrication of the test structures can begin immediately at the start of Phase 1.

Murphy, Michael C.↗

NASA NTRS2004

Investigation of Injector Slot Geometry on Curved-Diffuser Aerodynamic Performance

The Compressor Branch vision is to be recognized as world-class leaders in research for fluid mechanics of compressors. Its mission is to conduct research and develop technology to advance the state of the art of compressors and transfer new technology to U.S. industries. Maintain partnerships with U.S. industries, universities, and other government organizations. Maintain a balance between customers focused and long range research. Flow control comprises enabling technologies to meet compression system performance requirements driven by emissions and fuel reduction goals (e.g., in UEET), missions (e.g., access-to-space), aerodynamically aggressive vehicle configurations (e.g., UAV and future blended wing body configurations with highly distorted inlets), and cost goals (e.g., in VAATE). The compression system requirements include increased efficiency, power-to-weight, and adaptability (i.e., robustness in terms of wide operability, distortion tolerance, and engine system health and reliability). The compressor flow control task comprises efforts to develop, demonstrate, and transfer adaptive flow control technology to industry to increase aerodynamic loading at current blade row loss levels, to enable adaptive1 y wide operability, and to develop plant models for adaptive compression systems. In this context, flow control is the controlled modification of a flow field by a deliberate means beyond the natural (uncontrolled) shaping of the solid surfaces that define the principal flow path. The objective of the compressor flow control task is to develop and apply techniques that control circulation, aerodynamic blockage, and entropy production in order to enhance the performance and operability of compression systems for advanced aero-propulsion applications. This summer I would be working with a curved-diffuser because it simulates what happens with flow in the stator blades in the compressor. With this experiment I will be doing some data analysis and parametric study of the injector slot geometries to get the best aerodynamic performance of it. This includes some data reduction, redesign and fast prototyping of the injector nozzle.

Silva, Odlanier↗

NASA NTRS2008

Geologic Mapping along the Arabia Terra Dichotomy Boundary: Mawrth Vallis and Nili Fossae, Mars: Introductory Report

Geologic mapping studies at the 1:1M-scale will be used to characterize geologic processes that have shaped the highlands along the Arabia Terra dichotomy boundary. In particular, this mapping will evaluate the distribution, stratigraphic position, and lateral continuity of compositionally distinct outcrops in Mawrth Vallis and Nili Fossae as identified by spectral instruments currently in orbit. Placing these landscapes, their material units, structural features, and unique compositional outcrops into spatial and temporal context with the remainder of the Arabia Terra dichotomy boundary will provide the ability to: 1) further test original dichotomy formation hypotheses, 2) constrain ancient paleoenvironments and climate conditions, and 3) evaluate various fluvial-nival modification processes related to past and present volatile distribution and their putative reservoirs (aquifers, lakes and oceans, surface and ground ice) and the influences of nearby volcanic and tectonic features on hydrologic processes in these regions. The result will be two 1:1M scale geologic maps of twelve MTM quadrangles (Mawrth Vallis - 20022, 20017, 20012, 25022, 25017, and 25012; and Nili Fossae - 20287, 20282, 25287, 25282, 30287, 30282).

Bleamaster, Leslie F., III↗

NASA NTRS2009

Geologic Mapping along the Arabia Terra Dichotomy Boundary: Mawrth Vallis and Nili Fossae, Mars

Geologic mapping studies at the 1:1M-scale are being used to assess geologic materials and processes that shape the highlands along the Arabia Terra dichotomy boundary. In particular, this mapping will evaluate the distribution, stratigraphic position, and lateral continuity of compositionally distinct outcrops in Mawrth Vallis and Nili Fossae as identified by spectral instruments currently in orbit. Placing these landscapes, their material units, structural features, and unique compositional outcrops into spatial and temporal context with the remainder of the Arabia Terra dichotomy boundary may provide constraints on: 1) origin of the dichotomy boundary, 2) paleo-environments and climate conditions, and 3) various fluvial-nival modification processes related to past and present volatile distribution and their putative reservoirs (aquifers, lakes and oceans, surface and ground ice) and the influences of nearby volcanic and tectonic features on hydrologic processes in these regions. The results of this work will include two 1:1M scale geologic maps of twelve MTM quadrangles (Mawrth Vallis - 20022, 20017, 20012, 25022, 25017, and 25012; and Nili Fossae - 20287, 20282, 25287, 25282, 30287, 30282).

Bleamaster, Leslie F., III↗