Search NASA⌕ Search

SEARCH · Search NASA

Results for “TEST REACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Coordination of Plutonium Separations

NASA and the Department of Energy (DOE) are currently working together to reestablish a 238Pu supply capability using DOE's existing facilities and reactors. The effort is being led by Oak Ridge National Laboratory (ORNL). Target rods, containing neptunium oxide (NpO2), are fabricated at ORNL and irradiated in the ORNL High Flux Isotope Reactor (HFIR) currently and soon will be irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). Irradiated targets are processed in hot cells at the ORNL Radiochemical Engineering Center to recover the plutonium (Pu) product and unconverted neptunium (Np) for recycle. The 238PuO2 product is shipped to Los Alamos National Laboratory (LANL) for fabrication of heat source pellets. Key activities, such as the transport of the neptunium to ORNL, irradiation of neptunium, and chemical processing to recover the newly generated 238Pu, have been demonstrated with the initial amounts of ~100 g heat-source plutonium oxide (HS PuO2) produced. Product samples have been shipped to LANL for evaluation, including chemical impurity analysis. This paper will examine the status of producing new 238Pu from irradiated targets.

Wham, Robert↗

Ceramography and Thermal Modelling of Irradiated TRISO Particles using BISON

This study presents a comprehensive analysis of irradiated TRISO fuel particles from the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program conducted at the Advanced Test Reactor (ATR) as part of my internship. Failure Analysis using high-resolution microscopy was performed to characterize mechanisms in TRISO particle layers, including the kernel, buffer, inner pyrolytic carbon (IPyC), silicon carbide (SiC), and outer pyrolytic carbon (OPyC) coatings. Failure modes were systematically classified. Thermal conductivity properties of each TRISO layer were evaluated through experimental measurements and computational models for use in BISON finite element code. Experimental thermal conductivity values ranged from 0.5 W/m·K for the buffer layer to 168 W/m·K for SiC, while BISON simulations provided averaged values of 0.57 W/m·K (buffer), 4.0 W/m·K (PyC layers), and 15.95 W/m·K (SiC). Temperature-dependent correlations from PARFUME were implemented for kernel thermal properties.

BISON↗

Expansion of the Fuel Motion Monitoring System

The Idaho National Laboratory (INL) Transient Reactor Test Facility (TREAT) Fuel Motion Monitoring System (FMMS) is a diagnostic tool used to visualize the movement and location of fuel within the nuclear reactor during transient experiments. TREAT is designed to test the behavior of nuclear fuel under accident conditions, such as a rapid power increase. The TREAT FMMS, also referred to as the “hodoscope” because of the system’s massive steel collimator component, is located on the North beam port of the reactor. While the FMMS system is capable of incorporating a total of 360 sensors, initial refurbishment efforts resulted in a array of 96 fast neutron detectors. This initial array was configured to provide a narrow (2 channels) full-length view of experiment vessels with an extended 4-channel–wide region in the center of the array capable of providing a full view of all initially planned experiments. Planning and efforts to expand the FMMS array began immediately following the restart of TREAT. An additional 96 detectors were evaluated, characterized, and prepared for installation at TREAT during the summer of 2018. Unfortunately, funding reductions forced the project towards a 5-year hiatus. In October of 2023 funding from the Department of Energy’s Nuclear Science User Facilities enabled the expansion to recommence. This report serves to document the activities performed to expand the FMMS detector array to 192 channels in order to provide a broader view of the larger and more sophisticated test capsules currently planned for future irradiation in the TREAT reactor. This expansion also included doubling the data acquisition capability, addressing the new heat load on the system, and synchronizing the time for all digital components.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transient testing of uranium silicide fuel in zircaloy and silicon carbide cladding

Using the newly restarted Transient Reactor Test (TREAT) facility at Idaho National Laboratories, fresh (unirradiated) U 3 Si 2 fuel pellets were tested under reactivity-initiated accident conditions in dry helium capsules. These tests were performed with total energy depositions sufficient to induce melting of the U 3 Si 2 fuel pellets based on available thermophysical property data. The instrumented experiments utilized in-pile thermocouples and infrared pyrometers to measure the cladding temperature during the transient, which are in reasonable agreement with predicted peak cladding temperatures using a simple BISON fuel performance model. This same model is then used to predict expected cladding stresses during the transients in areas where pellet cladding interaction is expected. It was shown that for transient energy depositions up to 528J/g rod like geometry of the test articles was maintained. While it is acknowledged that more confirmatory testing is required in more prototypic environments, these first of their kind experiments have demonstrated that unirradiated U 3 Si 2 fuel and unirradiated SiC-SiC claddings can likely retain a “rod like” geometry for transient energy depositions up to 528J/g.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transmission Electron Microscopy based Characterization of a U-20Pu-10Zr Fuel Irradiated in Experimental Breeder Reactor-II

U-Pu-Zr metallic fuels are important fuel candidate for future advanced and/or test reactors. To better understand fuel performance and guide future fuel development, a U-20Pu-10Zr (in weight) metallic fuel irradiated in the Experimental Breeder Reactor was revisited using advanced electron microscopies. This fuel was irradiated to a burnup of 7.6 % at a peak cladding temperature of 521 °C. In this research, several transmission electron microscopy samples were extracted from different but representative radial locations of the fuel cross section using focused ion beam technique. Phase identification and chemical analysis with sub-micron spatial resolution was carried out using scanning transmission electron microscopy. Multiple phenomena that are critical to fuel performance, such as Zr phase and its distribution in a different matrix, were revealed in an unpreceded and highly detailed manner. An improved understanding of fuel reconstruction in U-Pu-Zr metallic fuel under reactor irradiation is provided.

36 MATERIALS SCIENCE↗

Simulation of natural circulation cartridge loop experiments and application to molten salt reactors

This work uses the TRAC/RELAP Advanced Computational Engine (TRACE) thermal hydraulics (TH) code to model natural circulation cartridge loop experiments previously conducted at Oak Ridge National Laboratory (ORNL) using water and compares the simulated and experimental results. TRACE is also used to characterize natural circulation in the cartridge loop vehicle using FLiNaK as the working fluid. The experimental vehicle is a buoyancy-aided, annular cartridge loop, referred to as a thermosyphon, and is designed to aid in qualifying liquid–fueled and/or liquid–cooled irradiation experiments for the Versatile Test Reactor (VTR), which is currently being designed in the United States. Out-of-pile water experiments have been conducted using the cartridge and the Thermosyphon Test Loop facility at ORNL, and future experiments are anticipated that would use other molten salt surrogates as the working fluid, followed by eventual insertion of a similar cartridge into VTR. Additionally, this work aims to determine how well TRACE can replicate the natural convection conditions that were observed experimentally; this serves as an initial step for validating the modeling tool for design and safety calculations to support future irradiation experiments in VTR. Initial predictions of potential experiments were made using FLiNaK as the natural circulation fluid to demonstrate the relevance of the cartridge design to molten salt reactors (MSRs). Results from this study indicate that TRACE can accurately capture natural convection phenomena in the thermosyphon and that several design changes to the current cartridge vehicle are necessary to achieve hydraulic conditions similar to those expected in MSRs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

AGR-3/4 Irradiation Test Train Disassembly and Component Metrology First Look Report

The AGR-3/4 experiment was designed to study fission product transport within graphitic matrix material and nuclear-grade graphite. To this end, this experiment consisted of 12 capsules, each fueled with 4 compacts containing UCO TRISO particles as driver fuel and 20 UCO designed-to-fail (DTF) fuel particles in each compact. The DTF fuel was fabricated with a thin pyrocarbon layer which was intended to fail during irradiation and provide a source of fission products. These fission products could then migrate through the compact and into the surrounding concentric rings of graphitic matrix material and/or nuclear graphite. Through post-irradiation examination (PIE) of the rings (including physical sampling and gamma scanning) fission product concentration profiles within the rings can be determined. These data can be used to elucidate fission product transport parameters (e.g. diffusion coefficients within the test materials) which will be used to inform and refine models of fission product transport. After irradiation in the Advanced Test Reactor (ATR) had been completed in April 2014, the AGR-3/4 experiment was shipped to the Hot Fuel Examination Facility (HFEF) at the Materials and Fuels Complex (MFC) for inspection, disassembly, and metrology. The AGR-3/4 test train was received at MFC in two separate shipments between February and April 2015. Visual examinations of the test train exterior did not indicate dimensional distortion, and only two small discolored areas were observed at the bottom of Capsules 8 and 9. No corresponding discoloration was found on the inside of these capsules, however. Prior to disassembly, the two test train sections were subject to analysis via the Precision Gamma Scanner (PGS), which did not indicate that any gross fuel relocation had occurred. A series of specialized tools (including clamps, cutters, and drills) had been designed and fabricated in order to carry out test train disassembly and recovery of capsule components (graphite rings and fuel compacts). This equipment performed well for separating each capsule in the test train and extracting the capsule components. Only a few problems were encountered. In one case, the outermost ring (the sink ring) was cracked during removal of the capsule through tubes. Although the sink ring will be analyzed in order to obtain a mass balance of fission products in the experiment, these cracks do not pose a major concern because the sink ring will not be analyzed in detail to obtain the spatial distribution of fission products. In Capsules 4 and 5, the compacts could not be removed from the inner rings. Strategies for removing the compacts are being evaluated. Sampling the inner rings with the compacts in-place is also an option. Dimensional measurements were made on the compacts, inner rings, outer rings, and sink rings. The diameters of all compacts decreased by 0.5 to 2.0 %. Generally, the extent of diametric shrinkage increased linearly with increasing neutron fluence. Most compact lengths also decreased. Compact lengths decreased with increasing fluence, reaching maximum shrinkage of about 0.9 % at a fast fluence of 4.0x1025 n/m2 E > 0.18 MeV. Above this fluence, the extent of length shrinkage appeared to decrease with fluence, and two compacts from Capsule 7 were found to have slightly increased in length (< 0.1 %) after a fluence of 5.2x1025 n/m2.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

01-07 Reactor Supplemental Shielding For the NRIC DOME Test Bed 01-07 Reactor Supplemental Shielding For the NRIC DOME Test Bed 2

A radiation shielding system is needed to protect personnel and equipment from harsh neutron and photon fluxes during: Reactor operations Post shut down operations Disassembly Decommissioning Examples of RSS driving requirements Radiological Controls Operating dose rate: the dose rate during normal reactor operations shall be <0.5 mrem/hr at the exterior wall of DOME containment Outdoor radiation limit: shielding shall provide the dose to a facility worker outside of DOME to <0.05 mrem/hr at 50 ft from the exterior wall of the DOME Temperature Reactors may have operating temperatures up to 800C The RSS shall be capable of removing up to 100 KW of heat during normal operating conditions the concrete structure has an upper temperature limit of 100°C

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Project X Energy Station Workshop Report. Report by the Organizers and Co-Conveners of the Project X Energy Station Workshop

On January 29–30, 2013, Fermilab hosted a workshop with the objective to identify and explore the nuclear energy relevant research and development that would be possible in a nuclear energy station associated with the Project X Linear Accelerator (linac). Recognizing that the U.S. Nuclear Energy mission will always require the use of test reactors, the hypotheses that a nuclear energy station associated with Project X could accelerate and enhance the ability to test and evaluate new materials and advanced reactor fuels was explored. Forty-five of the invited participants including staff from the U.S. Department of Energy (DOE), DOE Laboratories, universities, and other institutes attended the workshop. These participants were invited based on their technical expertise and relevant experience.

Asner, David M.↗

Overview and Current Status of Analyses of Potential LEU Design Concepts for TREAT

Neutronic and thermal-hydraulic analyses have been performed to evaluate the performance of different low-enriched uranium (LEU) fuel design concepts for the conversion of the Transient Reactor Test Facility (TREAT) from its current high-enriched uranium (HEU) fuel. TREAT is an experimental reactor developed to generate high neutron flux transients for the testing of nuclear fuels. The goal of this work was to identify an LEU design which can maintain the performance of the existing HEU core while continuing to operate safely. A wide variety of design options were considered, with a focus on minimizing peak fuel temperatures and optimizing the power coupling between the TREAT core and test samples. Designs were also evaluated to ensure that they provide sufficient reactivity and shutdown margin for each control rod bank. Analyses were performed using the core loading and experiment configuration of historic M8 Power Calibration experiments (M8CAL). The Monte Carlo code MCNP was utilized for steady-state analyses, and transient calculations were performed with the point kinetics code TREKIN. Thermal analyses were performed with the COMSOL multi-physics code. Using the results of this study, a new LEU Baseline design concept is being established, which will be evaluated in detail in a future report.

Connaway, H. M.↗

Confirmatory LBL Analysis of AGR-5/6/7 Compacts and Over-Coated Particles BWXT Batches 11034, 14154C, 14156C, AND 14156D

Fuel for the Advanced Gas Reactor Fuel Development and Qualification (AGR) Program’s AGR-5/6/7 irradiation test in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR) was produced by BWX Technologies (BWXT) Nuclear Operations Group in Lynchburg, Virginia. Tristructural isotropic (TRISO) coatings were deposited using a 150-mm-diameter production-scale fluidized-bed chemical vapor deposition (CVD) furnace on 425-μm-nominal-diameter spherical kernels from Lot J52R-16-69317 containing a mixture of 15.5% 235U low-enriched uranium carbide and uranium oxide (UCO). The TRISO coatings consisted of four consecutive CVD layers: a ~50% dense carbon buffer layer with 100-μmnominal thickness, a dense inner pyrolytic carbon (IPyC) layer with 40-μm-nominal thickness, a silicon carbide (SiC) layer with 35-μm-nominal thickness, and a dense outer pyrolytic carbon (OPyC) layer with 40-μm-nominal thickness. TRISO-coated particle Lot J52R-16-98005 was over-coated with a graphite/resin blend and these over-coated particles were pressed in half-inch-diameter, one-inch-long cylindrical compacts. Two packing fractions (PF) were produced, 40%PF and 25%PF, where the TRISO particle volume made up approximately 40% and 25% of the total compact volume, respectively. The AGR-5/6/7 Fuel Specification, SPC-1352 [Marshall 2016], provides the requirements necessary for acceptance of the fuel manufactured for the AGR-5/6/7 irradiation test. Quality control (QC) acceptance testing for all AGR-5/6/7 composited lots and single batches was performed by BWXT, with the exception of pyrolytic carbon (PyC) anisotropy and defective IPyC fraction in the TRISO candidate batches and final composite, which were measured at the Oak Ridge National Laboratory (ORNL) and reported in ORNL/TM-2017/036 [Hunn et al. 2017] and ORNL/TM-2017/037 [Helmreich et al. 2017a].

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Neutronics and Transient Calculations for the Conversion of the Transient Reactor Rest Facility (TREAT)

The Transient Reactor Test Facility (TREAT) is a graphite-reflected, graphitemoderated, and air-cooled reactor fueled with 93.1% enriched UO2 particles dispersed in graphite, with a carbon-to-235U ratio of ~10000:1. TREAT was used to simulate accident conditions by subjecting fuel test samples placed at the center of the core to high energy transient pulses. The transient pulse production is based on the core’s selflimiting nature due to the negative reactivity feedback provided by the fuel graphite as the core temperature rises. The analysis of the conversion of TREAT to low enriched uranium (LEU) is currently underway. This paper presents the analytical methods used to calculate the transient performance of TREAT in terms of power pulse production and resulting peak core temperatures. The validation of the HEU neutronics TREAT model, the calculation of the temperature distribution and the temperature reactivity feedback as well as the number of fissions generated inside fuel test samples are discussed.

Kontogeorgakos, Dimitrios C.↗

Postirradiation Examination of the ATF-1 Experiments - 2018 Status

The Advanced Fuels Campaign in collaboration with industry are working to develop enhanced accident tolerant fuels for light water reactors. The initial irradiations of these concepts were performed in the Idaho National Laboratory Advanced Test Reactor using simple drop-in style irradiations. These irradiations are collectively referred to as ATF 1. The postirradiation examination of ATF 1 has begun and some concepts have now completed initial examination. This report describes the results of examinations on ATF 1 irradiations designed to test the feasibility of enhancing UO 2 thermal conductivity with additives, ATF 1 irradiations of uranium silicide, and the current status of ATF 1 irradiations that are in process at the hot cell. Enhanced thermal conductivity uranium dioxide composites containing silicon carbide (UO 2 SiC) and diamond (UO 2 diamond) have been irradiated to low burnup. The conditions of this irradiation test and subsequent postirradiation examinations are discussed. These irradiations evaluate fuel microstructure and potential fuel cladding interaction under representative light water reactor power conditions. Both non destructive and destructive techniques have been used to evaluate fuel integrity, fission gas release, fission product distribution, burnup, fuel swelling and cladding strain. Examination of the UO 2 SiC pellets revealed enhanced cracking when compared to a UO 2 rodlet also irradiated under similar conditions. Additionally, instability of the SiC whiskers in the uranium dioxide matrix was observed in the pellet central region, where the local temperatures exceeded 1300 °C. The microstructure of the diamond added UO 2 was severely disrupted during irradiation, resulting in local migration of cesium along the fuel stack and increased fission gas release when compared with the expected release from the Vitanza curve at corresponding values of burnup and irradiation temperature. The postirradiation examination results cast doubt on the suitability of these additives to improve UO 2 fuel performance in a way that would lead to enhanced accident tolerance. Additionally, postirradiation examination data of U 3 Si 2 fuels at low burnup (i.e., < 20 GWd/tHM) for application in advanced Light Water Reactor (LWR) is presented. The U 3 Si 2 pellets show limited cracking in comparison to the expected behavior of UO 2 at same power level. In addition, gamma scanning data did not reveal migration of fission products. Minor homogeneous hardening along the pellet radius due to accumulation of fission products and radiation damage was measured by microindentation. The fission gas release and swelling remains very low. Formation of fission gas bubbles resolvable with optical microscopy occurs from the pellets center outward to approximately 60% of the fuel pellet radius. The overall data suggest a good performance of this accident tolerant fuel candidate at low burnup. Finally, the current status of postirradiation examination on other ATF 1 irradiations will be discussed. These irradiations include UO 2 clad in an FeCrAl alloy, an alternative uranium silicide compound U 3 Si 5 also clad in a FeCrAl alloy, and an interaction test between UO 2 and different FeCrAl alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NEA HTTR LOFC Project Test#3 Benchmark Results

In the second half of FY23, the High Temperature Engineering Test Reactor (HTTR) Loss Of Forced Cooling (LOFC)#3 data for the 9 MW test case with Vessel Cooling System (VCS) off were made available through the Nuclear Energy Agency (NEA) LOFC project framework; the neutronic model developed for the initial test (LOFC#1) achieved a satisfactory level of maturity, demonstrating its accuracy in predicting power evolution and core re-criticality, but LOFC#3 should be used primarily to investigate thermal hydraulic phenomena, as the reactor was shut down prematurely due to overheating in the upper reactor components, which prevented re-criticality; this report focuses on advancing the HTTR thermal hydraulic model to accurately simulate the LOFC#3 scenario, including simulating the LOFC#3 benchmark and generating the corresponding benchmark specifications, aiming to ensure consistency across participant models and provide essential data for future participants, including private industry stakeholders seeking to validate their computational tools.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

VALIDATION OF A RELAP5 POINT KINETICS MODEL OF TREAT

Development of advanced nuclear fuels requires testing of fuel specimens under various power-cooling mismatch conditions. The Transient Reactor Test (TREAT) facility at the Idaho National Laboratory will be used to provide transient nuclear heating of fuel specimens. Experiments will be conducted to support assessment of accident tolerant fuel designs being proposed for light water reactor applications. The experiments to be conducted at TREAT will provide data for the assessment of advanced, multi-physics computer codes. However, before the experiments can be performed, calculations are required to demonstrate that they will meet program objectives and that they can be performed safely in TREAT in the event of an unplanned reactivity insertion accident that occurs during the experiment. The safety calculations for the first experiments need to be performed in the next year and therefore will be performed with an existing computer code, RELAP5-3D. A point kinetics model of TREAT was developed for RELAP5-3D. The purpose of the model is to calculate the reactor power during experiments and to support the accident analyses of those experiments. The RELAP5-3D model was validated using data from nine TREAT experiments conducted previously. The RELAP5-3D model generates results that are in reasonable agreement with measured values of maximum core power, energy deposition, and maximum fuel temperature for a wide range of reactivity insertions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR 5/6/7 Data Qualification Report for ATR Cycles 162B through 168A

This report provides the qualification status of experimental data for the Advanced Gas Reactor (AGR) 5/6/7 fuel irradiation. AGR-5/6/7 was conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) in support of development and qualification of tri-structural isotropic (TRISO) low-enriched fuel for use in high temperature gas-cooled reactors. The objectives of the AGR-5/6/7 experiments are to: (i) irradiate reference-design fuel particles to support fuel qualification, (ii) establish operating margins for the fuel beyond normal operating conditions, and (iii) provide irradiated-fuel performance data and irradiated-fuel samples for post-irradiation examination (PIE) and safety testing. The test train contains five separate capsules that were independently controlled and monitored. Each capsule contains multiple 12.51-mm-long compacts filled with low enriched uranium carbide/oxide (UCO) TRISO fuel particles. The primary objective of the AGR-5/6 test (Capsules 1, 2, 4, and 5) is to verify successful performance of the reference-design fuel under normal operating conditions. The AGR-7 test (Capsule 3) was designed to explore fuel performance at higher temperatures to demonstrate the capability of the fuel to withstand conditions beyond normal operating conditions in support of plant design and licensing. AGR 5/6/7 will also provide irradiated-fuel performance data on fission-gas release from failed particles during irradiation. The AGR-5/6/7 capsules were irradiated in the ATR northeast flux trap location. The experiment began on February 16, 2018 and ended on July 22, 2020, spanning nine ATR cycles over two and a half years. Thus, the AGR-5/6/7 fuel compacts were irradiated for a total of 360.9 effective full power days. The AGR 5/6/7 experiment was able to remain in the reactor core during all three Powered Axial Locator Mechanism (PALM) cycles (163A, 165A, and 167A) without overheating its fuel compacts. This report includes irradiation monitoring data from nine ATR Cycles: 162B, 163A, 164A, 164B, 165A, 166A, 166B, 167A, and 168A, as stored in the Nuclear Data Management and Analysis System (NDMAS). During irradiation, data records consisted of instantaneous measurements recorded every minute and provided by text files automatically every 2 hours. The AGR 5/6/7 data streams addressed in this report include thermocouple (TC) temperatures, sweep gas data (flow rates [capsule inlet, outlet, and downstream at detector], pressure, and moisture content), and Fission Product Monitoring System (FPMS) data (release rates and release to birth rate ratios [R/Bs]) for each of the five capsules. A total of 94,989,908 TC temperature and sweep gas data records were received and processed by NDMAS for AGR 5/6/7 irradiation. Of these records, 41,593,387 (or 43.7% of the total) met data collection and accuracy requirements and are labeled as Qualified. A total of 57,746,693 TC temperature readings were captured from 54 installed TCs. Among them, 10,034,676 TC temperature records (only 17.4%) were Qualified and 47,701,371 TC temperatures (or 82.6%) are Failed due to 48 TC failures (63.5%) and due to missing values (19.1%). To assess performance of the operational TCs, analysis of daily correlations between TCs found no evidence of virtual junction failure for any TCs. Analyses on control charts of TC temperature differences revealed trending in TC readings for TC2, 4, 5, and 13 in Capsule 3, but there is no conclusive indication of TC drift failure that caused those trends. Therefore, TC control charts are not used to disqualify TC data, but only for users’ consideration. For sweep gas flow rates, a total of 31,519,747 gas flow records (84.4%) are Qualified for use for AGR-5/6/7 experiment; 5,723,468 gas flow records (15.4%) are Failed due mostly to missing values; and 74,641 high sweep gas flow rates (0.2 %) are Trend. A large number of Failed missing TC temperature and gas flow values were caused by an error in the data output script that outputted a ‘NULL’ value when values were unchanged. This problem was fixed during the outage of Cycle 166B, which led to a substantially decreased number of missing values during the last three cycles. Nonetheless, a large amount of non-missing data remained because of the high data acquisition frequency (1-minute) and still provided sufficient data to effectively monitor the experiment as designed. For FPMS data, NDMAS received and processed fission product release and R/B data for nine ATR cycles, when ATR core reached full power during AGR 5/6/7 irradiation. These data consist of 110,388 release rate records and 110,388 R/B records for the twelve radionuclides (Kr 85m, Kr 87, Kr 88, Kr 89, Kr 90, Xe 131m, Xe 133, Xe 135, Xe 135m, Xe 137, Xe 138, and Xe 139) for each of the five capsules. Equivalent numbers of uncertainty records associated the release rates and R/B values were provided. To date, qualification status of the FPMS data stored in the NDMAS dat

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal evaluation of uranium silicide miniplates irradiated at high heat flux

The Gas Test Loop (GTL)-1 irradiation experiment was conducted in the Advanced Test Reactor (ATR) to assess corrosion performance of proposed booster fuel at heat flux levels ~30% above the design operating condition. Sixteen miniplates fabricated from 25% enriched, high-density (4.8 g U/cm3) U3Si2/Al dispersion fuel with 6061 aluminum cladding were subjected to peak beginning of cycle (BOC) heat fluxes ranging from 411 to 593 W/cm2. No adverse impacts to the miniplates were observed at these high heat flux levels. A detailed finite element model was constructed to calculate temperatures and heat flux for an as-run cycle average effective ATR south lobe power of 25.4 MW(t). Miniplate heat flux levels and fuel, cladding, hydroxide, and coolant–hydroxide interface temperatures were calculated using the average hydroxide thickness on each miniplate measured during post-irradiation examination. The purpose of this study was to obtain a best estimate of the as-run experiment temperatures to aid in establishing acceptable heat flux levels and designing fuel qualification experiments for this fuel type.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

High-Temperature Fe-Based Fischer–Tropsch Synthesis: Experimentally Validated Kinetic Models Implemented at Pellet and Reactor Scales

Pellet- and reactor-scale models for Fischer–Tropsch synthesis (FTS) with a Fe–K/silica catalyst were developed to investigate the sensitivity of the hydrocarbon products and carbon dioxide selectivity to process conditions and feed composition at high temperature (350–400 °C), moderate pressure (1–10 bar), and a range of H 2 /CO ratios (3–1). The major objective of this paper is to develop, validate, and evaluate a high-temperature FTS model that is then used to assess the feasibility of process integration with syngas production. Since there is limited kinetic data available, in literature at these conditions, bench-scale reactor tests were conducted to obtain operational data for parameter fitting of kinetic expressions used in the model. This resulting kinetic model demonstrated agreement with the experimental data with an R 2 of 0.97 to the testing data set and, thus, was feasible to apply at pellet and reactor scales. Here, multiple pellet sizes were modeled to detail the role of transport limitations as the sphere’s diameter approached and exceeded 1 mm. Application of the reactor model indicated that hydrocarbon selectivity depended strongly on temperature, whereas the ratio of olefin to paraffin products decreased with increasing temperature, pressure, and H 2 /CO ratio. Product selectivity was not sensitive to the conversion of carbon monoxide. Furthermore, the roles of the pressure and H 2 /CO ratio were closely coupled. At a H 2 /CO ratio of 3, only slight variations in selectivity occurred over a pressure range of 1–20 bar, whereas at a ratio of 1, selectivity could vary by as much as 30% over the same pressure range. At pressures below 5 bar and temperatures above 350 °C, minimal selectivity to heavy hydrocarbons (C 12+ ) is obtained, and selectivity to midrange products (C 5–11 ) rapidly declined as pressure dropped below 5 bar, which indicated that an operational pressure of at least 5 bar is needed to achieve reasonable yields in this temperature range. These results, while tentative, provide guidelines for further experimentation and evaluation of integrated FTS processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗