Search NASA⌕ Search

SEARCH · Search NASA

Results for “compositional properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Fabrication, Microstructures, and Properties of 50 vol.% SiCp/6061Al Composites via Hot Pressing

Nearly fully dense 50 vol.% SiCp/6061Al composites were fabricated via hot pressing (HPing) at temperatures ranging from 610 to 650 °C, with the axial load and holding time fixed as 25 MPa and 120 min, respectively. The interfacial reactions, microstructures, and properties of the SiCp/Al alloy were studied. The interface reaction between SiCp and the Al alloy was suppressed at annealing temperatures of 620 °C and below; however, the reaction intensified as the annealing temperature increased, producing Al{sub 4}C{sub 3}, Si, and Mg{sub 2}Si. With an increase in HPing temperature from 610 to 630 °C, the 6061Al alloy melted and gradually filled the pores in the SiC particles under the applied load. The density, bending strength, and thermal conductivity (TC) of the composites increased, whereas the coefficient of thermal expansion (CTE) of the composites decreased. With an increase in HPing temperature increased from 630 to 650 °C, the 6061Al alloy melt leaked through the sintered bodies, resulting in the microstructural degradation and property reduction of the composites. The 50 vol.% SiCp/6061Al composites fabricated by HPing at 630 °C exhibited optimal comprehensive properties [bending strength, 332.4 MPa; TC, 186.3 W(m K){sup −1}; and CTE, 7.9 × 10{sup −6}/°C (20-100 °C)], which were attributed to the highest relative density and the best SiCp/Al interfacial structure of the composites.

36 MATERIALS SCIENCE↗

Mechanical Properties of Carbon Fiber Reinforced Composites Exposed to Cryogenic Conditions and Space Radiation via Simulation and Testing

As NASA missions extend beyond low Earth orbit, increasing reliance is placed on carbon fiber reinforced polymer (CFRP) composites for spacecraft structures where mass efficiency, durability, and long-term reliability are critical. In service, these materials are subjected to a combination of ultraviolet radiation, vacuum, ionizing radiation, atomic oxygen, and extreme thermal excursions under sustained mechanical loading. Flight systems such as the Boeing Starliner and SpaceX Dragon employ external composite structures that will experience these environments for extended durations. Although prior spaceflight and ground studies have reported limited changes in bulk mechanical properties, the synergistic effects of these environments on composite microstructure, particularly at the fiber matrix interphase, remain insufficiently characterized and represent a potential qualification and reliability risk. This study investigates the effects of short-term cryogenic exposure on a radiation shielding carbon epoxy composite, SC2020, as a ground-based analog for space relevant thermal extremes. The SC2020 material system has previously flown on the International Space Station under the Materials International Space Station Experiment (MISSE) program. Composite specimens were exposed to liquid nitrogen for 6 and 24 hours and evaluated using a multiscale characterization framework that combined ASTM D3039 tensile testing, Atomic Force Microscopy (AFM) based interphase analysis, and helium gas permeability measurements. Tensile testing showed no statistically significant or permanent degradation in global strength or modulus following cryogenic exposure. In contrast, AFM measurements revealed reductions in interphase modulus, weakened adhesion, and increased nanoscale heterogeneity, indicating localized degradation mechanisms not captured by conventional bulk testing. Gas permeability measurements showed a progressive increase in helium diffusion with exposure duration, consistent with micro-void formation or partial interfacial debonding. The results indicate that cryogenic exposure initiates degradation at the fiber matrix interphase while leaving global mechanical properties largely unchanged over short durations. These findings underscore the importance of multiscale diagnostics for identifying early-stage damage mechanisms that may influence long term performance and qualification margins for spaceflight composite structures. The data presented establish a cryogenic baseline for comparison with forthcoming MISSE flight exposure results and support ongoing NASA Established Program to Stimulate Competitive Research (EPSCoR) efforts aimed at improving composite qualification methodologies, risk assessment, and reliability prediction for space environments.

composite reliability↗

Compositional control of electrical transport properties in the new series of defect thiospinels, Ga{sub 1-x}Ge{sub x}V{sub 4}S{sub 8-{delta}} (0<=x<=1)

A new series of non-stoichiometric sulfides Ga{sub 1-x}Ge{sub x}V{sub 4}S{sub 8-{delta}} (0<=x<=1; delta<=0.23) has been synthesized at high temperatures by heating stoichiometric mixtures of the elements in sealed quartz tubes. The samples have been characterized by powder X-ray diffraction, SQUID magnetometry and electrical transport-property measurements. Structural analysis reveals that a solid solution is formed throughout this composition range, whilst thermogravimetric data reveal sulfur deficiency of up to 2.9% in the quaternary phases. Magnetic measurements suggest that the ferromagnetic behavior of the end-member phase GaV{sub 4}S{sub 8} is retained at x<=0.7; samples in this composition range showing a marked increase in magnetization at low temperatures. By contrast Ga{sub 0.25}Ge{sub 0.75}V{sub 4}S{sub 8-{delta}} appears to undergo antiferromagnetic ordering at ca. 15 K. All materials with xnot =1 are n-type semiconductors whose resistivity falls by almost six orders of magnitude with decreasing Ga content, whilst the end-member phase GeV{sub 4}S{sub 8-{delta}} is a p-type semiconductor. The results demonstrate that the physical properties are determined principally by the degree of electron filling of narrow-band states arising from intracluster V-V interactions. - Graphical abstract: Chemical substitution and sulfur non-stoichiometry produce dramatic changes in the transport properties of defect thiospinels Ga{sub 1-x}Ge{sub x}V{sub 4}S{sub 8-{delta}}.

36 MATERIALS SCIENCE↗

Corrosion-Resistant Hydrophobic Nanostructured Ni-Reduced Graphene Oxide Composite Coating with Improved Mechanical Properties

In the present work, corrosion-resistant and hydrophobic nickel-reduced graphene oxide (Ni-RGO) composite coating prepared by electroless deposition technique on mild steel (MS), without the use of toxic chemicals, is reported. The field emission scanning electron microscopy micrographs show a uniform composite coating of Ni-RGO with smaller grain size, whereas cuboidal and larger grains were observed in the case of Ni coating on MS. A reduction in crystallite size from 30 to 13 nm with the incorporation of RGO to the Ni matrix was estimated from XRD. The corrosion activity was investigated with potentiodynamic polarization and electrochemical impedance spectroscopy measurements. The surface of Ni-RGO composite coating remained intact, almost undamaged and showed a robust resistance to corrosion with an inhibition efficiency of about 95% in aggressive 3.5 wt.% NaCl solution. Nanoindentation test revealed that the hardness and Young’s modulus of Ni-RGO composite coating are increased by about 25 and 19%, respectively, as compared to Ni coating.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Fluorescent of C-dot composite thin films and its properties

In the present work, we report the preparation of a fluorescent carbon nanodots (C-dots) epoxy composite thin films on a glass substrate. C-dots were prepared directly by a simple hydrothermal method using citric acid as a carbon source. The C-dots solutions were mixed with a transparent epoxy resin to form C-dot epoxy composite. Furthermore, the composite precursor was deposited on the glass substrate using a spin coating method in order to fabricate C-dot epoxy composite thin film. The transmittance intensity of C-dot composite film reached up to 90% in the visible light spectra. Using Swanopoel method, the film thickness of fabricated C-dot composite film was determined at about 1.45 μm, a value lies in a typical range needed for a wide range application. Thus, the C-dot composite film is promising in broadening applications in various fields such as energy conversion, optoelectronics, and display technology.

36 MATERIALS SCIENCE↗

Predicting electrical conductivity in Cu/Nb composites: A combined model-experiment study

The generation of high magnetic fields requires materials with high electric conductivity and good strength properties. Cu/Nb composites are considered to be good candidates for this purpose. In this work, we aim to predict, from theory, the dependence of electric conductivity on the microstructure, most notably on the layer thickness and grain sizes. We also conducted experiments to calibrate and validate our simulations. Bimetal interfaces and grain boundaries are confirmed to have the largest impact on conductivity in this composite material. In this approach, a distribution of the layer thickness is accounted for in order to better model the experimentally observed microstructure. Because layer thicknesses below the mean free path of Cu significantly degrade the conductivity, an average layer thickness larger than expected may be needed to meet conductivity requirements in order to minimize these smaller layers in the distribution. We also investigate the effect of variations in volume fraction of Nb and temperature on the material’s conductivity.

36 MATERIALS SCIENCE↗

An overview of self-consistent methods for fiber-reinforced composites

The Walker et al. (1989) self-consistent method to predict both the elastic and the inelastic effective material properties of composites is examined and compared with the results of other self-consistent and elastically based solutions. The elastic part of their method is shown to be identical to other self-consistent methods for non-dilute reinforced composite materials; they are the Hill (1965), Budiansky (1965), and Nemat-Nasser et al. (1982) derivations. A simplified form of the non-dilute self-consistent method is also derived. The predicted, elastic, effective material properties for fiber reinforced material using the Walker method was found to deviate from the elasticity solution for the v sub 31, K sub 12, and mu sub 31 material properties (fiber is in the 3 direction) especially at the larger volume fractions. Also, the prediction for the transverse shear modulus, mu sub 12, exceeds one of the accepted Hashin bounds. Only the longitudinal elastic modulus E sub 33 agrees with the elasticity solution. The differences between the Walker and the elasticity solutions are primarily due to the assumption used in the derivation of the self-consistent method, i.e., the strain fields in the inclusions and the matrix are assumed to remain constant, which is not a correct assumption for a high concentration of inclusions.

Gramoll, Kurt C.↗

Production of Ni-Cr-Ti-natural fibres composite and investigation of mechanical properties

Intermetallic materials such as Ni{sub 2}Ti, Cr{sub 2}Ti are among advanced technology materials that have outstanding mechanical and physical properties for high temperature applications. Especially creep resistance, low density and high hardness properties stand out in such intermetallics. The microstructure, mechanical properties of (%50Ni-%48Cr-%2Ti)-%10Naturel Fibres and (%64Ni-%32Cr-%4Ti)-%10Naturel Fibres powders were investigated using specimens produced by tube furnace sintering at 1000-1200-1400°C temperature. A composite consisting of ternary additions, a metallic phase, Ti,Cr and Ni have been prepared under Ar shroud and then tube furnace sintered. XRD, SEM (Scanning Electron Microscope), were investigated to characterize the properties of the specimens. Experimental results carried out for composition (%64Ni-%32Cr-%4Ti)-%10Naturel at 1400°C suggest that the best properties as 112.09HV and 5,422g/cm{sup 3} density were obtained at 1400°C.

36 MATERIALS SCIENCE↗

The optimal fiber volume fraction and fiber-matrix property compatibility in fiber reinforced composites

Although the question of minimum or critical fiber volume fraction beyond which a composite can then be strengthened due to addition of fibers has been dealt with by several investigators for both continuous and short fiber composites, a study of maximum or optimal fiber volume fraction at which the composite reaches its highest strength has not been reported yet. The present analysis has investigated this issue for short fiber case based on the well-known shear lag (the elastic stress transfer) theory as the first step. Using the relationships obtained, the minimum spacing between fibers is determined upon which the maximum fiber volume fraction can be calculated, depending on the fiber packing forms within the composites. The effects on the value of this maximum fiber volume fraction due to such factors as fiber and matrix properties, fiber aspect ratio and fiber packing forms are discussed. Furthermore, combined with the previous analysis on the minimum fiber volume fraction, this maximum fiber volume fraction can be used to examine the property compatibility of fiber and matrix in forming a composite. This is deemed to be useful for composite design. Finally some examples are provided to illustrate the results.

Pan, Ning↗

Advanced Composite Pistons

New concept involving improved configuration of reinforcing fibers and improved fabrication process proposed to improve thermal and mechanical properties of composite piston structures. Reduces amount of labor necessary to manufacture piston structures, with attendant reductions in costs. Single knitted-carbon-fiber sock used to form external surfaces of piston. Advantages include elimination of heavy dependence on inherently weak interlaminar properties of carbon-carbon; ease of automation to reduce fabrication costs; readily modifiable architecture to vary mechanical properties to desired values; and reduction in number of elements required to fabricate pistons. Advantage of piston structures lies in applications where light weight and high specific performance primary considerations.

Taylor, Allan H.↗

Fillers for improved graphite fiber retention by polymer matrix composites

This program was designed to develop technology for fabrication of graphite/epoxy composites containing selected boron and boron-containing fillers, determine the effects of the fillers on physical and mechanical properties of composites, and evaluate the effectiveness of the boron fillers for fiber retention when the composites are exposed to fire conditions followed by impact. Fillers evaluated were crystalline and amorphous boron, boron carbide, and aluminum boride. The fillers were evaluated by mixing with Narmco 5208 resin matrix at quantities up to 5%. Graphite composites were fabricated and evaluated with respect to their mechanical properties, resistance to humidity, and burning characteristics. Also, the mechanism by which the fillers prevented fiber release was studied.

Sheppard, C. H.↗

Effect of heat treatment on stiffness and damping of SiC/Ti-15-3

The effect of heat treatment on material properties of SiC/Ti-15-3 was measured by vibration tests. Heat treatment changes the microstructure, which was found to stiffen the matrix and reduce its damping capacity. Test results indicate how these changes in the matrix affect the corresponding properties of the composite. Measurements show that heat treatment affects damping properties of the composite to a greater extent than stiffness properties. The extent of change in mechanical properties is shown to depend on heat treatment temperature and exposure time.

Grady, Joseph E.↗

XANES analysis of phosphate glasses melted with Tb 4 O 7 and SnO: evaluating the impact of valence states on structural, thermal, and luminescent properties

Barium phosphate glasses were prepared with 0.5 mol% Tb 4 O 7 added alongside SnO up to 5 mol% with the purpose of evaluating the resulting terbium and tin oxidation states and their impact on glass structural, thermal, and luminescent properties. In this work, following material synthesis by melt-quenching, the composition-structure–property investigation was pursued encompassing measurements by X-ray diffraction (XRD), X-ray absorption near-edge spectroscopy (XANES), Raman spectroscopy, differential scanning calorimetry (DSC), dilatometry, and photoluminescence (PL) spectroscopy. While XRD confirmed the amorphous nature of the glasses, results from XANES indicated that terbium occurs as terbium(III) with a predisposition for tin to exist as tin(IV) which decreased at high SnO content. The structural as well as the thermal properties appeared to be mostly impacted by the presence of tin(IV). Specifically, glass depolymerization was indicated to be induced by Sn 4+ ions, and their concentration was observed to correlate with glass transition and softening temperatures. On the other hand, the tin(II) remnants were observed to exert an impact on the luminescent properties shifting light emission from the green towards the blue-green (cyan). It is indicated that Tb 4 O 7 reacting to produce Tb 2 O 3 supports the oxidation of tin(II) to tin(IV) which in turn dominates the physical properties. However, this was somewhat circumvented at the highest SnO content wherein tin(IV) appeared to be lower.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Digital Multiphase Composites via Additive Manufacturing

Abstract Mechanical properties of traditional engineering materials are typically coupled to each other, presenting a challenge to practitioners with multi‐dimensional material property requirements. In this work, continuous, independent control over multiple mechanical properties is demonstrated in composite materials realized using additive manufacturing. For the first time, composites additively manufactured from rigid plastic, soft elastomer, and liquid constituents are experimentally characterized, demonstrating materials which span four orders of magnitude in modulus and two orders of magnitude in toughness. By forming analytical mappings between relative concentrations of constituents at the microscale and resulting macroscale material properties, inverse material design is enabled; the method is showcased by printing artifacts with prescribed toughness and elasticity distributions. The properties of these composites are placed in the context of biological tissues, showing they have promise as mechanically plausible tissue mimics.

Smith, Lawrence T.↗

Elevated-temperature application of the IITRI compression test fixture for graphite/polyimide filamentary composites

Seventy-nine graphite/polyimide compression specimens were tested to investigate experimentally the IITRI test method for determining compressive properties of composite materials at room and elevated temperatures (589 K (600 F)). Minor modifications were made to the standard IITRI fixture and a high degree of precision was maintained in specimen fabrication and load alignment. Specimens included four symmetric laminate orientations. Various widths were tested to evaluate the effect of width on measured modulus and strength. In most cases three specimens of each width were tested at room and elevated temperature and a polynomial regression analysis was used to reduce the data. Scatter of replicate tests and back-to-back strain variations were low, and no specimens failed by instability. Variation of specimen width had a negligible effect on the measured ultimate strengths and initial moduli of the specimens. Measured compressive strength and stiffness values were sufficiently high for the material to be considered a usable structural material at temperatures as high as 589 K (600 F).

Raju, B. B.↗

Progressive fracture in composites subjected to hygrothermal environment

The effects of temperature and moisture on the load carrying capability and structural response properties of composites are investigated via computational simulation. An integrated computer code is utilized for the simulation of composite structures under loading. Damage initiation, damage growth, fracture progression, and global structural fracture are included in the simulation. Results demonstrate the significance of hygro-thermal effects on composite structural response, toughness, and durability.

Minnetyan, Levon↗

Thin-Layer Composite Unimorph Ferroelectric Driver Sensor Properties

Tests were conducted on 13 different configurations of a new class of piezoelectric devices called THUNDER (thin layer composite unimorph ferroelectric driver and sensor). These configurations consisted of a combination of 1, 3, 5, 7, and 9 layers of 25.4 micron thick aluminium as a backing material, with and without a top layer of 25.4 micrometer aluminum. All of these configurations used the same piezoelectric ceramic wafer (PZT-5A) with dimensions of 5.08 x 3.81 x 0.018 cm. The above configurations were tested at two stages of the manufacturing process: before and after repoling. The parameters measured included frequency, driving voltage. displacement, capacitance, and radius of curvature. An optic sensor recorded the displacement at a fixed voltage(100 - 400 V peak to peak) over a predetermined frequency range (1 - 1000 Hz). These displacement measurements were performed using a computer that controlled the process of activating and measuring the displacement of the device. A parameter alpha was defined which can be used to predict the which configuration will produce the most displacement for a free standing device.

Mossi, Karla M.↗

Effects of Heat Input on Weld-Bead Geometry, Surface Chemical Composition, Corrosion Behavior and Thermal Properties of Fiber Laser-Welded Nitinol Shape Memory Alloy

Bead-on-plate laser welding was carried out on 1-mm-thick Nitinol sheets at different heat input values. The variations in weld-bead geometry and variations in microstructures across the bead were studied. The effects of heat input on surface layer composition of the welded samples, corrosion properties and phase transformation temperature were examined. From x-ray photoelectron spectroscopy (XPS), it was clear that relative intensity of elemental Ni peak was higher in parent material and the oxidation state of Ti was Ti{sup 4+}. It was further observed from Auger electron spectroscopy (AES) that the Ti to Ni ratio on the top surface of the welded samples was more than 1, and as a result of this the stability of TiO{sub 2} layer was enhanced, which eventually helped to improve the corrosion property of the welded samples. The polarization resistance of the welded samples was increased by more than ten times compared to that of the un-welded samples. From differential scanning calorimetry (DSC), it became evident that phase transformation temperatures got changed due to welding.

36 MATERIALS SCIENCE↗