Search NASA⌕ Search

SEARCH · Search NASA

Results for “delta method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Launch opportunity classification of VEGA and delta V-EGA trajectories to the outer planets

Two concepts in spacecraft trajectory design which have been proposed by Hollenbeck (1975) and Bender and Friedlander (1975) are considered. Both concepts are intended for planetary missions and require an earth reencounter created by either a Venus gravity assist (VEGA) or a large midcourse impulse (delta V-EGA). In the case of outer planet missions, the new concepts offer significantly lower launch energy requirements than the direct ballistic flight mode. However, at least an additional two years flight time is needed for geometry phasing to set up the earth reencounter. A description is given of the trajectory characteristics for the two concepts. Attention is also given to the method of analysis used for the studies, aspects of trajectory generation, payload calculations, and target opportunity data.

Stancati, M. L.↗

An evaluation of preliminary Doppler global velocimetry measurements

A review of Doppler Global Velocimetry (DGV) data obtained during wind tunnel tests on a 75 degree swept delta wing was performed. High frequency variations observed in normalized data files are attributed to image alignment problems. Unfortunately, initial DGV velocity data compared poorly with baseline reference data. Nonlinear DGV system operation during the tests is the likely source of this problem. Corrected data compares much more favorably and suggests that DGV is a valid measurement technique. Future DGV investigations should include a method or means for monitoring laser frequency relative to the ALF transfer function behavior.

Miller, L. Scott↗

Molecular Modeling of the Poling of Piezoelectric Polyimides

The computational method described in this paper allows the calculation of the dielectric relaxation strength of an amorphous polymer based solely upon its chemical structure. The 4,4' oxydiphthalic anhydride (ODPA) dianhydride and bis-aminophenoxybenzene (APB) diamine based polyimides, (beta-CN) APB-ODPA and APB-ODPA were studied. Amorphous cells were constructed and then poled using molecular dynamics. Dielectric relaxation strengths of Delta(epsilon) = 17.8 for (beta-CN) APB-ODPA and Delta(epsilon) = 7.7 for APB-ODPA were predicted. These values are in excellent agreement with the experimental values. It was found that both the pendant nitrile dipole and the backbone anhydride residue dipole make significant contributions to the polyimides dielectric response. Specifically, it was shown that the difference in the magnitude of the dielectric relaxations is directly attributable to the nitrile dipole. The size of the relaxations indicate an absence of cooperative dipolar motions, The model was used to explain these results in terms of the average orientation of the nitrile and anhydride dipoles to within 51 deg. and 63 deg., respectively, of the applied electric field.

Young, J. A.↗

Solvation thermodynamics and heat capacity of polar and charged solutes in water

The solvation thermodynamics and in particular the solvation heat capacity of polar and charged solutes in water is studied using atomistic molecular dynamics simulations. As ionic solutes we consider a F{sup -} and a Na{sup +} ion, as an example for a polar molecule with vanishing net charge we take a SPC/E water molecule. The partial charges of all three solutes are varied in a wide range by a scaling factor. Using a recently introduced method for the accurate determination of the solvation free energy of polar solutes, we determine the free energy, entropy, enthalpy, and heat capacity of the three different solutes as a function of temperature and partial solute charge. We find that the sum of the solvation heat capacities of the Na{sup +} and F{sup -} ions is negative, in agreement with experimental observations, but our results uncover a pronounced difference in the heat capacity between positively and negatively charged groups. While the solvation heat capacity {Delta}C{sub p} stays positive and even increases slightly upon charging the Na{sup +} ion, it decreases upon charging the F{sup -} ion and becomes negative beyond an ion charge of q=-0.3e. On the other hand, the heat capacity of the overall charge-neutral polar solute derived from a SPC/E water molecule is positive for all charge scaling factors considered by us. This means that the heat capacity of a wide class of polar solutes with vanishing net charge is positive. The common ascription of negative heat capacities to polar chemical groups might arise from the neglect of non-additive interaction effects between polar and apolar groups. The reason behind this non-additivity is suggested to be related to the second solvation shell that significantly affects the solvation thermodynamics and due to its large spatial extent induces quite long-ranged interactions between solvated molecular parts and groups.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Density slope of the nuclear symmetry energy from the neutron skin thickness of heavy nuclei

Expressing explicitly the parameters of the standard Skyrme interaction in terms of the macroscopic properties of asymmetric nuclear matter, we show in the Skyrme-Hartree-Fock approach that unambiguous correlations exist between observables of finite nuclei and nuclear matter properties. We find that existing data on neutron skin thickness {Delta}r{sub np} of Sn isotopes give an important constraint on the symmetry energy E{sub sym}({rho}{sub 0}) and its density slope L at saturation density {rho}{sub 0}. Combining these constraints with those from recent analyses of isospin diffusion and the double neutron/proton ratio in heavy-ion collisions at intermediate energies leads to a more stringent limit on L approximately independent of E{sub sym}({rho}{sub 0}). The implication of these new constraints on the {Delta}r{sub np} of {sup 208}Pb as well as the core-crust transition density and pressure in neutron stars is discussed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Primeval galaxies in the sub-mm and mm

Although the results of COBE's FIRAS experiment 1 constrain the deviation in energy from the CMB blackbody in the 500-5000 micron range to be delta E/E, sub cmb less than 0.005, primeval galaxies can still lead to a brilliant sub-mm sky of non-Gaussian sources that are detectable at 10 inch resolution from planned arrays such as SCUBA on the James Clerk Maxwell Telescope and, quite plausibly, at sub-arcsecond resolution in planned mm and sub-mm interferometers. Here, we apply our hierarchical peaks method to a CDM model to construct sub-mm and mm maps of bursting PG's appropriate for these instruments with minimum contours chosen to correspond to realistic observational parameters for them and which pass the FIRAS limits.

Bond, J. Richard↗

The Strategy for the Second Phase of Aerobraking Mars Global Surveyor

On February 19, 1999, the Mars Global Surveyor (MGS) spacecraft was able to propulsively establish its mapping orbit. This event followed the completion of the second phase of aerobraking for the MGS spacecraft on February 4, 1999. For the first time, a spacecraft at Mars had successfully employed aerobraking methods in order to reach its desired pre-launch mapping orbit. This was accomplished despite a damaged spacecraft solar array. The MGS spacecraft was launched on November 7, 1996, and after a ten month interplanetary transit was inserted into a highly elliptical capture orbit at Mars on September 12, 1997. Unlike other interplanetary missions, the MGS spacecraft was launched with a planned mission delta-V ((Delta)V) deficit of nearly 1250 m/s. To overcome this AV deficit, aerobraking techniques were employed. However, damage discovered to one of the spacecraft's two solar arrays after launch forced major revisions to the original aerobraking planning of the MGS mission. In order to avoid a complete structural failure of the array, peak dynamic pressure levels for the spacecraft were established at a major spacecraft health review in November 1997. These peak dynamic pressure levels were roughly one-third of the original mission design values. Incorporating the new dynamic pressure limitations into mission replanning efforts resulted in an 'extended' orbit insertion phase for the mission. This 'extended' orbit insertion phase was characterized by two distinct periods of aerobraking separated by an aerobraking hiatus that would last for several months in an intermediate orbit called the "Science Phasing Orbit" (SPO). This paper describes and focuses on the strategy for the second phase of aerobraking for the MGS mission called "Aerobraking Phase 2." This description will include the baseline aerobraking flight profile, the trajectory control methodology, as well as the key trajectory metrics that were monitored in order to successfully "guide' the spacecraft to its desired mapping orbit. Additionally, the actual aerobraking progress is contrasted to the planned aerobraking flight profile. (A separate paper will describe the navigation aspects of MGS aerobraking in detail.) Key to the success of the MGS mission is the delivery of the spacecraft to its final mapping orbit and the synergy the instrument complement provides to its scientific investigators when science data is returned from that orbit. The MGS mapping orbit is characterized as a low altitude, near-circular, near-polar orbit that is Sun-synchronous with the descending equatorial crossing at 2:00 AM local mean solar time (LMST).

Johnston, M. D.↗

Deep Space Transportation System Using the Sun-Earth L2 Point

Recently, various kinds of planetary explorations have become more feasible, taking the advantage of low thrust propulsion means such as ion engines that have come into practical use. The field of space activity has now been expanded even to the rim of the outer solar system. In this context, the Japan Aerospace Exploration Agency (JAXA) has started investigating a Deep Space Port built at the L2 Lagrange point in the Sun-Earth system. For the purpose of making the deep space port practically useful, there is a need to establish a method to making spaceship depart and return from/to the port. This paper first discusses the escape maneuvers originating from the L2 point under the restricted three-body problem. Impulsive maneuvers from the L2 point are extensively studied here, and using the results, optimal low-thrust escape strategies are synthesized. Furthermore, this paper proposes the optimal escape and acceleration maneuvers schemes using Electric Delta-V Earth Gravity Assist (EDVEGA) technique.

Matsumoto, Michihiro↗

The Multiple Use Plug Hybrid for NanoSats (MUPHyN) Miniature Thruster

The Multiple Use Plug Hybrid (for) Nanosats is a prototype thruster is being developed to fill a niche application for NanoSat-scale spacecraft propulsion. When fully developed, the MUPHyN thruster will provide an effective and low-risk propulsive capability that could enable multiple NanoSats to be independently re-positioned after deployment from a parent launch vehicle. Because the environmentally benign, chemically-stable propellants are mixed only within the combustion chamber after ignition and the flow rate of the fuel is determined by a pyrolysis mechanism that is nearly independent of pressure or fuel grain defects, the system is inherently safe and can be piggy-backed near a secondary payload with little or no overall mission risk increase to the primary payload. The MUPHyN thruster uses safe-handling and inexpensive nitrous oxide (N2O) and acrylonitrile-butadiene-styrene (ABS) as propellants. Fused Deposition Modeling (FDM), a direct digital manufacturing process, is used to fabricate short-form-factor solid fuel grains with multiple helical combustion ports from ABS thermoplastic. This manufacturing process allows for the rapid development and manufacture of complex fuel grain geometries that are not possible to extrude or cast using conventional methods. This technology enables the construction of fuel grains with length-to-diameter ratios appropriate for incorporation into CubeSats while maintaining high surface areas and regression rates that allow the system to maintain a near optimal oxidizer to fuel ratio. The MUPHyN system provides attitude control torques by using secondary-injection thrust vectoring on a truncated aerospike nozzle. This configuration allows large impulse delta V burns and small impulse attitude control firings to be performed with the same system. To ensure survivability during extend duration burns, the MUPHyN incorporates a novel regenerative cooling design where the N2O oxidizer flows through a cooling path embedded in the aerospike nozzle before being injected into the combustion chamber near the nozzle base.

Eilers, Shannon D.↗

Mars Sample Return Landed with Red Dragon

A Mars Sample Return (MSR) mission is the highest priority science mission for the next decade as recommended by the recent Decadal Survey of Planetary Science. However, an affordable program to carry this out has not been defined. This paper describes a study that examined use of emerging commercial capabilities to land the sample return elements, with the goal of reducing mission cost. A team at NASA Ames examined the feasibility of the following scenario for MSR: A Falcon Heavy launcher injects a SpaceX Dragon crew capsule and trunk onto a Trans Mars Injection trajectory. The capsule is modified to carry all the hardware needed to return samples collected on Mars including a Mars Ascent Vehicle (MAV), an Earth Return Vehicle (ERV) and Sample Collection and Storage hardware. The Dragon descends to land on the surface of Mars using SuperSonic Retro Propulsion (SSRP) as described by Braun and Manning [IEEEAC paper 0076, 2005]. Samples are acquired and deliverd to the MAV by a prelanded asset, possibly the proposed 2020 rover. After samples are obtained and stored in the ERV, the MAV launches the sample-containing ERV from the surface of Mars. We examined cases where the ERV is delivered to either low Mars orbit (LMO), C3 = 0 (Mars escape), or an intermediate energy state. The ERV then provides the rest of the energy (delta V) required to perform trans-Earth injection (TEI), cruise, and insertion into a Moon-trailing Earth Orbit (MTEO). A later mission, possibly a crewed Dragon launched by a Falcon Heavy (not part of the current study) retrieves the sample container, packages the sample, and performs a controlled Earth re-entry to prevent Mars materials from accidentally contaminating Earth. The key analysis methods used in the study employed a set of parametric mass estimating relationships (MERs) and standard aerospace analysis software codes modified for the MAV class of launch vehicle to determine the range of performance parameters that produced converged spacecraft designs capable of meeting mission requirements. Subsystems modeled in this study included structures, power system, propulsion system, nose fairing, thermal insulation, actuation devices, and GN&C. Best practice application of loads and design margins for all resources were used. Both storable and cryogenic propellant systems were examined. The landed mass and lander capsule size provide boundary conditions for the MAV design and packaging. We estimated the maximum mass the Dragon capsule is capable of landing. This and the volume capability to store the MAV was deduced from publically available data from SpaceX as well as our own engineering and aerodynamic estimates. Minimum gross-liftoff mass (GLOM) for the MAV were obtained for configurations that used pump-fed storable bi-propellant rocket engines for both the MAV and the ERV stage. The GLOM required fits within our internal estimate of the mass that Dragon can land at low elevation/optimal seasons on Mars. Based on the analysis, we show that a single Mars launch sample return mission is feasible using current commercial capabilities to deliver the return spacecraft assets.

Mars Ascent Vehicle (MAV)↗

Fabrication and characterization of SmO{<_0.7}F{<_2}FeAs bulk with a transition temperature of 56.5K.

The superconductivity of iron-based superconductor SmO{sub 0.7}F{sub 0.2}FeAs was investigated. The SmO{sub 0.7}F{sub 0.2}FeAs sample was prepared by the two-step solid-state reaction method. The onset resistivity transition temperature is as high as 56.5 K. X-ray diffraction (XRD) results show that the lattice parameters a and c are 0.39261 and 0.84751 nm, respectively. Furthermore, the global J{sub c} was more than 2.3 x 10{sup 5} A/cm2 at T = 10 K and H = 9 T, which was calculated by the formula of J{sub c} = 20 {Delta} M/[a(1 - a/(3b))]. The upper critical fields, H{sub c2} {approx} 256 T (T = 0 K), was determined according to the Werthamer-Helfand-Hohenberg formula, indicating that the SmO{sub 0.7}F{sub 0.2}FeAs was a superconductor with a very promising application.

36 MATERIALS SCIENCE↗

Exposure to Pb, Cd, and As mixtures potentiates the production of oxidative stress precursors: 30-day, 90-day, and 180-day drinking water studies in rats

Exposure to chemical mixtures is a common and important determinant of toxicity and is of particular concern due to their appearance in sources of drinking water. Despite this, few in vivo mixture studies have been conducted to date to understand the health impact of chemical mixtures compared to single chemicals. Interactive effects of lead (Pb), cadmium (Cd) and arsenic (As) were evaluated in 30-, 90-, and 180-day factorial design drinking water studies in rats designed to test the hypothesis that ingestion of such mixtures at individual component Lowest-Observed-Effect-Levels (LOELs) results in increased levels of the pro-oxidant delta aminolevulinic acid (ALA), iron, and copper. LOEL levels of Pb, Cd, and As mixtures resulted in the increased presence of mediators of oxidative stress such as ALA, copper, and iron. ALA increases were followed by statistically significant increases in kidney copper in the 90- and 180-day studies. Statistical evidence of interaction was identified for six biologically relevant variables: blood delta aminolevulinic acid dehydratase (ALAD), kidney ALAD, urinary ALA, urinary iron, kidney iron, and kidney copper. The current investigations underscore the importance of considering interactive effects that common toxic agents such as Pb, Cd, and As may have upon one another at low-dose levels. The interactions between known toxic trace elements at biologically relevant concentrations shown here demonstrate a clear need to rigorously review methods by which national/international agencies assess health risks of chemicals, since exposures may commonly occur as complex mixtures.

60 APPLIED LIFE SCIENCES↗

Grain transport in three-dimensional soft dusty plasma states

Three-dimensional molecular dynamics simulations of aggregates of dust grains interacting via repulsive Yukawa forces, and subject to heating by neutrals and realistic boundary conditions, suggest that grain transport is ubiquitously anomalous for soft states at the transition between liquid and solid. These anomalies include self-similar, stretched-Gaussian, probability density distributions of grain displacements and superdiffusive displacement scaling on the short time scales for which the mean displacements sigma(tau) are less than the interparticle distance DELTA. However, the details of the anomalous transport on these shorter time scales depend on system stiffness and confinement conditions. On time scales for which sigma(tau)>=DELTA, humps can develop on the distribution at integer multiples of DELTA, an effect of cooperative hopping of grains on the lattice. Relaxation toward Gaussian displacement distributions and normal diffusion takes place on time scales for which sigma(tau)>DELTA. The simulations indicate that qualitative features previously found for hexatic states of two-dimensional aggregates by simulation and experiment are also present in three-dimensional configurations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Neutron density distributions of {sup 204,206,208}Pb deduced via proton elastic scattering at E{sub p}=295 MeV

Cross sections and analyzing powers for polarized proton elastic scattering from {sup 58}Ni, and {sup 204,206,208}Pb were measured at intermediate energy E{sub p}=295 MeV. An effective relativistic Love-Franey interaction is tuned to reproduce {sup 58}Ni scattering data within the framework of the relativistic impulse approximation. The neutron densities of the lead isotopes are deduced using model-independent sum-of-Gaussians distributions. Their error envelopes are estimated by a new {chi}{sup 2} criterion including uncertainties associated with the reaction model. The systematic behaviors of extracted error envelopes of the neutron density distributions in {sup 204,206,208}Pb are presented. The extracted neutron and proton density distribution of {sup 208}Pb gives a neutron skin thickness of {Delta}r{sub np}=0.211{sub -0.063}{sup +0.054} fm.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

A Method for Computing the Core Flow in Three-Dimensional Leading-Edge Vortices

A theory is presented for calculating the flow in the core of a separation-induced leading-edge vortex. The method is based on matching inner and outer representations of the vortex. The inner model of the vortex is based on the quasicylindrical Navier-Stokes equations; the flow is assumed to be steady, axially symmetric, and incompressible and in addition, gradients in the radial direction are assumed to be much larger then gradients in the axial direction. The outer model is based on the three-dimensional free-vortex-sheet theory, a higher-order panel method which solves the Prandtl-Glauert equation including nonlinear boundary conditions pertinent to the concentrated vorticity representation of the leading edge vortex. The resultant flow is evaluated a posteriori for evidence of incipient vortex breakdown and the critical helix angle concept, in conjunction with an adverse longitudinal pressure gradient, is found to correlate well with the occurrence of vortex breakdown at the trailing edge of delta, arrow, and diamond wings.

Luckring, J. M.↗

Solar wind variations and geomagnetic storms - A study of individual storms based on high time resolution ISEE 3 data

Two independent methods are employed to determine the relationship between the parameter epsilon and total energy dissipation rate of the magnetosphere U sub T by selecting disturbed periods from the same data d set used by Baker et al. (1983). Specifically, four storms are examined in detail, since the accuracy of estimating U sub T is significantly improved during disturbed periods. The first method assumes that U sub T = M sub A exp.2- alpha(epsilon) where M sub A is the Alfven Mach number and alpha varies with time. The second method considers a linear, time-invariant dynamic system with epsilon as input and U sub T as output. This means that U sub T = W(asterisk)epsilon where asterisk is the convolution and W is a transfer function characteristic of the system. It is found that alpha values fluctuate mainly between 0 and -0.25. The transfer function analysis indicates that W often resembles a delta-function or a narrow rectangular impulse. Both results give the same implication (namely that U sub T is approximately equal to epsilon) and thus are consistent with the view that the magnetosphere is primarily a directly driven system during disturbed periods.

Akasofu, S.-I.↗

The aerodynamic design of the oblique flying wing supersonic transport

The aerodynamic design of a supersonic oblique flying wing is strongly influenced by the requirement that passengers must be accommodated inside the wing. It was revealed that thick oblique wings of very high sweep angle can be efficient at supersonic speeds when transonic normal Mach numbers are allowed on the upper surface of the wing. The goals were motivated by the ability to design a maximum thickness, minimum size oblique flying wing. A 2-D Navier-Stokes solver was used to design airfoils up to 16 percent thickness with specified lift, drag and pitching moment. A new method was developed to calculate the required pressure distribution on the wing based on the airfoil loading, normal Mach number distribution and theoretical knowledge of the minimum drag of oblique configurations at supersonic speeds. The wing mean surface for this pressure distribution was calculated using an inverse potential flow solver. The lift to drag ratio of this wing was significantly higher than that of a comparable delta wing for cruise speeds up to Mach 2.

Vandervelden, Alexander J. M.↗

Mass of Saturn's A ring

The mass of Saturn's A ring is reestimated using the behavior of spiral density waves embedded in the ring. The Voyager photopolarimeter (PPS) observed the star delta-Scorpii as it was occulted by Saturn's rings during the Voyager 2 flyby of Saturn in 1981 producing a radial profile of the rings. We examined forty spiral density waves in the Voyager PPS data of the A ring including 10 weaker waves that have not been previously analyzed by means of an autoregressive power spectral technique called Burg. The strengths of this new method for ring studies are that weaker, less extended waves are easily detected and characterized. This method is also the first one which does not require precise knowledge of the resonance location and phase of the wave in order to calculate the surface mass density. Uncertainties of up to 3 km are present in the currently available radial scales for Saturn's rings.

Horn, L. J.↗