Search NASA⌕ Search

SEARCH · Search NASA

Results for “dimensional analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Silane as an ignition aid in scramjets

This paper presents the results of experiments on silane/hydrogen combustion in a scramjet model configured as a constant area duct with a central injector. Intake flow conditions were created by free piston shock tunnels with simulated flight speeds ranging between 1.4 and 4.2 km/s. Intake conditions were restricted to three nominal Mach numbers. Boundary layer heating appeared to be responsible for ignition at low temperature, high Mach number conditions. Concentration of silane in hydrogen was varied, as well as intake temperature and pressure. Results indicated that silane in concentrations as low as 2.5 percent in hydrogen, was effective as a fuel additive for scramjets at conditions where hydrogen alone could not support combustion. An unsteady effect was observed as the intake temperature approached the lower limit for combustion. The combustion temperature limit rose significantly as the intake pressure was reduced to low levels. Computer simulations using a one dimensional premixed analysis suggested that although silane enhanced the combustion process, it was strongly dependent on the initial concentration of free radical oxygen. Results from the simulations were comparable to experimental results for some conditions.

Morris, N. A.↗

Euler analysis of the three-dimensional flow field of a high-speed propeller - Boundary condition effects

The results of an investigation of the effects of far field boundary conditions on the solution of the three dimensional Euler equations governing the flow field of a high speed single rotation propeller are presented. The results show that the solutions obtained with the nonreflecting boundary conditions are in good agreement with experimental data. The specification of nonreflecting boundary conditions is effective in reducing the dependence of the solution on the location of the far field boundary. Details of the flow field within the blade passage and the tip vortex are presented. The dependence of the computed power coefficient on the blade passage and the tip vortex are presented. The dependence of the computed power coefficient on the blade setting angle is examined.

Nallasamy, M.↗

Strain-Energy-Release Rates In Delamination

Q3DG computer program developed to perform quasi-three-dimensional stress analysis of composite laminates containing delaminations. Calculates strain-energy-release rates for long, rectangular composite laminates containing delaminations and subjected to any combination of mechanical, thermal, and hygroscopic loading. Written in FORTRAN V.

Raju, I. S.↗

Three-Dimensional Complex Variables

Report presents new theory of analytic functions of three-dimensional complex variables. While three-dimensional system subject to more limitations and more difficult to use than the two-dimensional system, useful in analysis of three-dimensional fluid flows, electrostatic potentials, and other phenomena involving harmonic functions.

Martin, E. Dale↗

Development of Moire machine vision

Three dimensional perception is essential to the development of versatile robotics systems in order to handle complex manufacturing tasks in future factories and in providing high accuracy measurements needed in flexible manufacturing and quality control. A program is described which will develop the potential of Moire techniques to provide this capability in vision systems and automated measurements, and demonstrate artificial intelligence (AI) techniques to take advantage of the strengths of Moire sensing. Moire techniques provide a means of optically manipulating the complex visual data in a three dimensional scene into a form which can be easily and quickly analyzed by computers. This type of optical data manipulation provides high productivity through integrated automation, producing a high quality product while reducing computer and mechanical manipulation requirements and thereby the cost and time of production. This nondestructive evaluation is developed to be able to make full field range measurement and three dimensional scene analysis.

Harding, Kevin G.↗

Structural optimization of turbine blade firtrees

On the basis of the present optimization equation for the structural capacity of a turbine blade attachment firtree, the optimum of the lobe circular fillet radius in the blade and in the turbine disk is determined. In order to further diminish peak stress in firtree design, an elliptical fillet radius is selected in place of the circular one. Two-dimensional stress analysis results for a three-lobe firtree with elliptical radius shows a 14-percent stress reduction in the blade necks (where cracking has been experienced) over the current, four-lobe firtree design.

Lee, R. L.↗

Boundary force method for analyzing two-dimensional cracked plates

The Boundary Force Method (BFM) was formulated for the two-dimensional stress analysis of complex crack configurations. In this method, only the boundaries of the region of interest are modeled. The boundaries are divided into a finite number of straight-line segments, and at the center of each segment, concentrated forces and a moment are applied. This set of unknown forces and moments is calculated to satisfy the prescribed boundary conditions of the problem. The elasticity solution for the stress distribution due to concentrated forces and a moment applied at an arbitrary point in a cracked infinite plate are used as the fundamental solution. Thus, the crack need not be modeled as part of the boundary. The formulation of the BFM is described and the accuracy of the method is established by analyzing several crack configurations for which accepted stress-intensity factor solutions are known. The crack configurations investigated include mode I and mixed mode (mode I and II) problems. The results obtained are, in general, within + or - 0.5 percent of accurate numerical solutions. The versatility of the method is demonstrated through the analysis of complex crack configurations for which limited or no solutions are known.

Tan, Paul W.↗

Computational unsteady aerodynamics for lifting surfaces

Two dimensional problems are solved using numerical techniques. Navier-Stokes equations are studied both in the vorticity-stream function formulation which appears to be the optimal choice for two dimensional problems, using a storage approach, and in the velocity pressure formulation which minimizes the number of unknowns in three dimensional problems. Analysis shows that compact centered conservative second order schemes for the vorticity equation are the most robust for high Reynolds number flows. Serious difficulties remain in the choice of turbulent models, to keep reasonable CPU efficiency.

Edwards, John W.↗

A zonal flow analysis method for two-dimensional airfoils

A closed-loop, overlapped, velocity-coupling procedure has been utilized to combine a two-dimensional potential flow panel code and a Navier-Stokes code. The fully coupled, two-zone code has been used to compute the flow past a NACA 0012 airfoil. For this case, the zonal method has shown that the grid domain size can be reduced to 0.14 chord lengths with less than 1 percent loss in accuracy. Further, the required computation time is reduced by a factor of approximately four.

Summa, J. Michael↗

Substorm electrodynamics

The present one-dimensional model analysis of substorm electrodynamics proceeds from the standard scenario in which the plasma sheet collapses into a neutral sheet, and magnetic merging occurs between the two tail lobes; plasma flows into the neutral sheet from the lobes and the sides, undergoing acceleration in the dawn-dusk direction. The process is modified by the tendency of the accelerated plasma to unbalance charge neutrality, leading to an exchange of electrons with the ionosphere in order to maintain neutrality. The cross-tail current is weakened by the diversion: this reduces the adjacent lobe-field intensity, but without notable effects apart from a slight expansion of the tail boundary.

Stern, David P.↗

Unsteady blade surface pressures on a large-scale advanced propeller - Prediction and data

An unsteady three dimensional Euler analysis technique is employed to compute the flowfield of an advanced propeller operating at an angle of attack. The predicted blade pressure waveforms are compared with wind tunnel data at two Mach numbers, 0.5 and 0.2. The inflow angle is three degrees. For an inflow Mach number of 0.5, the predicted pressure response is in fair agreement with data: the predicted phases of the waveforms are in close agreement with data while the magnitudes are underpredicted. At the low Mach number of 0.2 (take-off) the numerical solution shows the formation of a leading edge vortex which is in qualitative agreement with measurements. However, the highly nonlinear pressure response measured on the blade suction surface is not captured in the present inviscid analysis.

Nallasamy, M.↗

The effect of weak interface on transverse properties of a ceramic matrix composite

Experimental studies conducted at NASA Lewis on SiC reaction-bonded Si3N4 composite system showed that transverse stiffness and strength were much lower than those predicted from existing analytical models based on good interfacial bonding. It was believed that weakened interfaces were responsible for the decrease in tranverse properties. To support this claim, a two-dimensional FEM analysis was performed for a transverse representative volume element. Specifically, the effect of fiber/matrix displacement compatibility at the interface was studied under both tensile and compressive transverse loadings. Interface debonding was represented using active gap elements connecting the fiber and matrix. The analyses show that the transverse tensile strength and stiffness are best predicted when a debonded interface is assumed for the composite. In fact, the measured properties can be predicted by simply replacing the fibers by voids. Thus, it is found that little or no interfacial bonding exists in the composite, and that an elastic analysis can predict the transverse stiffness and strength.

Shimansky, R. A.↗

A three-dimensional equivalent domain integral method for cracked solids

Three-dimensional FEM analysis is presently undertaken via the general formulation of the equivalent-domain integral method for mixed-mode fracture problems in general anisotropic and nonlinear materials. In mixed-mode integrals, the total J-integral is split into three separate modes of fracture; direct and decomposition methods are effective in this separation of the modes, as presently demonstrated by their application to several pure and mixed-mode fracture problems. The results are found to agree well with those reported in the literature, and suggest the usefulness of the method as a FEM-program postprocessing subroutines.

Shivakumar, K. N.↗

Analysis of the one-dimensional transient compressible vapor flow in heat pipes

The transient compressible one-dimensional vapor flow dynamics in a heat pipe is modeled. The numerical results are obtained by using the implicit non-iterative Beam-Warming finite difference method. The model is tested for simulated heat pipe vapor flow and actual vapor flow in cylindrical heat pipes. A good comparison of the present transient results for the simulated heat pipe vapor flow with the previous results of a two-dimensional numerical model is achieved and the steady state results are in agreement with the existing experimental data. The transient behavior of the vapor flow under subsonic, sonic, and supersonic speeds as well as high mass flow rates are successfully predicted.

Jang, Jong H.↗

Potential Flows From Three-Dimensional Complex Variables

Report presents investigation of several functions of three-dimensional complex variable, with emphasis on potential-flow fields computed from these functions. Part of continuing research on generalization of well-established two-dimensional complex analysis to three and more dimensions.

Martin, E. Dale↗

Computer Simulation For Design Of TWT's

A three-dimensional finite-element analytical technique facilitates design and fabrication of traveling-wave-tube (TWT) slow-wave structures. Used to perform thermal and mechanical analyses of TWT designed with variety of configurations, geometries, and materials. Using three-dimensional computer analysis, designer able to simulate building and testing of TWT, with consequent substantial saving of time and money. Technique enables detailed look into operation of traveling-wave tubes to help improve performance for future communications systems.

Bartos, Karen F.↗

The natural flow wing-design concept

A wing-design study was conducted on a 65 degree swept leading-edge delta wing in which the wing geometry was modified to take advantage of the naturally occurring flow that forms over a slender wing in a supersonic flow field. Three-dimensional nonlinear analysis methods were used in the study which was divided into three parts: preliminary design, initial design, and final design. In the preliminary design, the wing planform, the design conditions, and the near-conical wing-design concept were derived, and a baseline standard wing (conventional airfoil distribution) and a baseline near-conical wing were chosen. During the initial analysis, a full-potential flow solver was employed to determine the aerodynamic characteristics of the baseline standard delta wing and to investigate modifications to the airfoil thickness, leading-edge radius, airfoil maximum-thickness position, and wing upper to lower surface asymmetry on the baseline near-conical wing. The final design employed an Euler solver to analyze the best wing configurations found in the initial design and to extend the study of wing asymmetry to develop a more refined wing. Benefits resulting from each modification are discussed, and a final 'natural flow' wing geometry was designed that provides an improvement in aerodynamic performance compared with that of a baseline conventional uncambered wing, linear-theory cambered wing, and near-conical wing.

Wood, Richard M.↗