Search NASA⌕ Search

SEARCH · Search NASA

Results for “reflection data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Evaluation of atmospheric particulate concentrations derived from analysis of ratio Thematic Mapper data

An approach for atmospheric particulate concentration evaluation above urban areas using ratio Thematic Mapper (TM) data is discussed. October 25, 1982 TM data over Chicago, IL are analyzed using TM band ratios of 1/2, 1/3, 1/4, 1/5, and 1/6 and particulate concentration estimates derived from TM ratios are tested over low reflective turbid water sites and highly reflective concrete highways. From analysis of the data it is evident that for water, the pattern of increasing particulate concentration is associated with decreasing ratio values in all band combinations used. Over concrete features, the TM band 1/4 ratio values follow the predicted pattern, while the TM band 1/6 has ratios which are reversed from anticipated values.

Carnahan, W. H.↗

Summary of Terra and Aqua MODIS On-orbit Calibration and Characterization Results

The Moderate Resolution Imaging Spectroradiometer (MODIS) onboard NASA's EOS Terra spacecraft has been in operation for more than seven years since its launch in December 1999 and the MODIS onboard Aqua spacecraft has been in operation for more than 4.5 years since its launch in May 2002. Compared to its heritage sensors, such as AVHRR, CZCS, SeaWiFS, HIRS, and Landsat TM, the MODIS instrument was developed with improved spectral and spatial resolutions, and temporal scale or global coverage frequency. The two MODIS instruments are nearly identical with each collecting data in 36 spectral bands: 20 reflective solar bands (RSB) with center wavelengths from 0.41 to 2.2jm and 16 thermal emissive bands (TEB) from 3.7 to 4.4 microns. MODIS makes the Earth view observations with a scan angle range of +/-55 degree relative to instrument nadir and at three nadir spatial resolutions: 0.25km for bands 1-2.05km for bands 3-7, and 1km for bands 8-36, thus enabling complete global coverage of the Earth in less than 2 days. Both Terra and Aqua MODIS observations have been routinely used to generate a broad range of science data products that are widely distributed and extensively applied for the studies of the Earth's land, oceans, and atmosphere and for the monitoring of climate and environmental changes. It is obvious that the MODIS science data product quality strongly relies on sensor on-orbit performance and its capability of continuously tracking sensor response changes over time. Because of this, each MODIS was built with a comprehensive set of on-board calibrators (OBC) that include a solar diffuser (SD) for the RSB calibration, a blackbody (BB) for the TEB calibration, and a spectro-radiometric calibration assembly (SRCA) for the spatial (RSB and TEB) and spectral (RSB only) characterization. Most importantly, extensive and dedicated sensor calibration and characterization efforts have been constantly made by the MODIS Characterization Support Team (MCST) at NASA/GSFC. In this presentation, we will provide an overview of MODIS sensor operations since 1aunh and the onorbit calibration and characterization methodologies with emphasis on the differences between Terra and Aqua MODIS characteristics. We will summarize both Terra and Aqua MODIS onorbit calibration and characterization results, including their RSB and TEB detector noise characterization, the sensor response changes, and the corrections to the optics degradation. In addition to radiometric calibration performance, we will illustrate both sensors' spectral and spatial characterization results in terms of their band-to-band registrations and spectral band center wavelength shifts.

Xiong, X.↗

BOREAS RSS-19 1996 CASI At-Sensor Radiance and Reflectance Images

The BOREAS RSS-19 team collected CASI images from the Chieftain Navaho aircraft in order to observe the seasonal change in the radiometric reflectance properties of the boreal forest landscape. CASI was deployed as a site-specific optical sensor as part of BOREAS. The overall objective of the CASI deployment was to observe the seasonal change in the radiometric reflectance properties of the boreal forest landscape. In 1996, image data were collected with CASI on 15 days during a field campaign between 18-July and 01 -August, primarily at flux tower sites located at study sites near Thompson, Manitoba, and Prince Albert, Saskatchewan. A variety of CASI data collection strategies were used to meet the following scientific objectives: 1) canopy bidirectional reflectance, 2) canopy biochemistry, 3) spatial variability, and 4) estimates of up and downwelling PAR spectral albedo, as well as changes along transects across lakes at the southern site and transects between the NSA and SSA. The images are stored as binary image files. The data files are available on a CD-ROM (see document number 20010000884) or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Miller, John↗

Spatially resolved methane band photometry of Jupiter. I - Absolute reflectivity and center-to-limb variations in the 6190-, 7250-, and 8900-A bands. II - Analysis of the south equatorial belt and south tropical zone reflectivity

Spatially resolved measurements of the absolute reflectivity and center to limb variations of Jupiter in the 6190, 7250 and 8900 A methane bands and nearby continuum regions are presented and analyzed for the south equatorial belts (SEBs) and south tropical zone (STrZ). It is found that the polar hoods, equatorial zone, Red Spot and north tropical zone have highest methane reflectivities, with the temperate zones and polar regions having low reflectivity and the STrZ and SEBs having intermediate values. The data on the SEB and STrZ are analyzed in terms of diffuse reflecting-scattering and two-cloud models of the vertical distribution of aerosols in the Jovian atmosphere. To fit observations, the STrZ cloud top must have between 0.55 and 0.43 bar total pressure and optical depth between 1.5 and 2.5. The reflecting-scattering models are not suitable for the SEBs. The SEB upper cloud is deeper, cloud thickness is less and the lower cloud is deeper than in the STrZ. A forward scattering haze layer accounts for limb darkening in the continuum.

West, R. A.↗

DGEN Aeropropulsion Research Turbofan (DART): Lossless Projection of Measured Engine Noise Spectra to a 1-Foot-Radius Arc

Baseline noise and aerodynamic data have been acquired for the DGEN Aeropropulsion Research Turbofan (DART) test rig. The DART is a fully-mobile engine test rig featuring a DGEN380 geared turbofan producing approximately 500 lbs. of thrust at sea level and a self-contained control room. Baseline noise data were acquired using 5 microphone arrays, varying distance, configuration, and angle to reflect the measurement locations at several other test facilities. Noise data were acquired at one array location on each test day to establish the repeatability of the measurements. The noise data from the different arrays is analyzed to show the limitations of projecting the results to a common radius when the noise sources are distributed and the measurement location is not in the geometric far-field.

Noise↗

Evidence of Boundary Reflection of Kelvin and First-Mode Rossby Waves

TOPEX/POSEIDON sea level data leads to new opportunities to investigate some theoretical mechanisms suggested to be involved in the El Nino/Southern Oscillation phenomenon in the tropical Pacific ocean. In particular, we are interested in studying the western boundary reflection, a process crucial for the delayed action oscillator theory, by using the TOPEX/POSEIDON data from November 1992 to May 1995.

boundary reflection TOPEX/POSEIDON↗

Induction of models under uncertainty

This paper outlines a procedure for performing induction under uncertainty. This procedure uses a probabilistic representation and uses Bayes' theorem to decide between alternative hypotheses (theories). This procedure is illustrated by a robot with no prior world experience performing induction on data it has gathered about the world. The particular inductive problem is the formation of class descriptions both for the tutored and untutored cases. The resulting class definitions are inherently probabilistic and so do not have any sharply defined membership criterion. This robot example raises some fundamental problems about induction; particularly, it is shown that inductively formed theories are not the best way to make predictions. Another difficulty is the need to provide prior probabilities for the set of possible theories. The main criterion for such priors is a pragmatic one aimed at keeping the theory structure as simple as possible, while still reflecting any structure discovered in the data.

Cheeseman, Peter↗

Comparison of Measurements and FluorMOD Simulations for Solar Induced Chlorophyll Fluorescence and Reflectance of a Corn Crop under Nitrogen Treatments [SIF and Reflectance for Corn]

The FLuorescence Explorer (FLEX) satellite concept is one of six semifinalist mission proposals selected in 2006 for pre-Phase studies by the European Space Agency (ESA). The FLEX concept proposes to measure passive solar induced chlorophyll fluorescence (SIF) of terrestrial ecosystems. A new spectral vegetation Fluorescence Model (FluorMOD) was developed to include the effects of steady state SIF on canopy reflectance. We used our laboratory and field measurements previously acquired from foliage and canopies of corn (Zea mays L.) under controlled nitrogen (N) fertilization to parameterize and evaluate FluorMOD. Our data included biophysical properties, fluorescence (F) and reflectance spectra for leaves; reflectance spectra of canopies and soil; solar irradiance; plot-level leaf area index; and canopy SIF emissions determined using the Fraunhofer Line Depth principal for the atmospheric telluric oxygen absorption features at 688 nm (O2-beta) and 760 nm (O2-alpha). FluorMOD simulations implemented in the default "look-up-table" mode did not reproduce the observed magnitudes of leaf F, canopy SIF, or canopy reflectance. However, simulations for all of these parameters agreed with observations when the default FluorMOD information was replaced with measurements, although N treatment responses were underestimated. Recommendations were provided to enhance FluorMOD's potential utility in support of SIF field experiments and studies of agriculture and ecosystems.

Middleton, Elizabeth M.↗

Measuring near infrared spectral reflectance changes from water stressed conifer stands with AIS-2

Airborne Imaging Spectrometer-2 (AIS-2) data was acquired over two paired conifer stands for the purpose of detecting differences in spectral reflectance between stressed and natural canopies. Water stress was induced in a stand of Norway spruce and white pine by severing the sapwood near the ground. Water stress during the AIS flights was evaluated through shoot water potential and relative water content measurements. Preliminary analysis with raw AIS-2 data using SPAM indicates that there were small, inconsistent differences in absolute spectral reflectance in the near infrared 0.97 to 1.3 micron between the stressed and natural canopies.

Riggs, George↗

A Revised Calibration Function and Results for the Phoenix Mission TECP Relative Humidity Sensor

The original calibration function of the R(sub H) sensor on the Phoenix Thermal and Electrical Conductivity Sensor (TECP) has been revised in order to extend the range of the valid calibration, and to improve accuracy. The original function returned non-physical R(sub H) values at the lowest temperatures. To resolve this, and because the original calibration was performed against a pair of hygrometers that measured frost point (T(sub f)), the revised calibration equation is also cast in terms of frost point. Because of the complexity of maintaining very low temperatures and high R(sub H) in the laboratory, no calibration data exists at T is greater than 203K. However, sensor response during the mission was smooth and continuous down to 181 K. Therefore we have opted to include flight data in the calibration data set; selection was limited to data acquired during periods when the atmosphere is known to have been saturated. T(sub f) remained below 210 K throughout the mission(P is greater than 0.75 Pa). R(sub H), conversely, ranged from 1 to well under 0.01 diurnally, due to approximately 50 K temperature variations. To first order, both vapor pressure and its variance are greater during daylight hours. Variance in overnight humidity is almost entirely explained by temperature, while atmospheric turbulence contributes substantial variance to daytime humidity. Likewise, data gathered with the TECP aloft reflect higher H2O abundances than at the surface, as well as greater variance. There is evidence for saturation of the atmosphere overnight throughout much of the mission. In virtually every overnight observation, once the atmosphere cooled to T(sub f), water vapor begins to decrease, and tracks air temperature. There is no evidence for substantial decreases in water vapor prior to saturation, as expected for adsorptive exchange. Likewise, there is no evidence of local control of vapor by phases such as perchlorate hydrates hydrated minerals. The daytime average H2O pressure does not change substantially over the course of the mission, although the H2O column abundance varies by a factor of 2. Column abundances calculated from TECP data are lower than orbital measurements if one assumes that H2O is uniformly mixed through a single scale height. These results argue that the vertical distribution of H2O begins to change well in advance of surface concentrations as northern autumn approaches.

Phoenix Thermal and Electrical Conductivity Sensor↗

Polar motion from laser range measurements of GEOS-3

Using two-day arcs of GEOS-3 laser data, simultaneous solutions for pole position components, x sub p and y sub p, and orbit elements have been obtained for the period spanning 3 February to 6 March 1976 using three NASA Goddard Space Flight Center laser stations located near Washington, D.C. (STALAS) and on the islands of Bermuda and Grand Turk. The results are in general agreement with the BIH results. However, because of the locations of the laser sites, the x sub p solution is weaker than the y sub p solution. The x sub p and y sub p estimates were smoothed with a straight line by weighted least squares using the variance associated with the pole estimates as weights in order to reflect the effect of widely different data distributions. The smoothed y sub p differs by one meter with respect to the BIH smoothed values and the smoothed x sub p differs by about two meters. Spectral analysis of the results has identified frequencies associated with the orbital motion indicating the need for further improvements in the model of the physical system.

Schutz, B. E.↗

Delay Tolerant, Radio Frequency Identification (RFID )-enabled Sensing

Radio Frequency Identification (RFID) technology offers a completely passive method to transmit fixed data sequences from an RFID tag, which typically doesn’t have its own power supply, to an interrogator. Radio frequency (RF) energy harvested from the interrogator is rectified by the tag and used to charge an integrated circuit (IC). The IC then modulates the received signal with the data stored on the tag and reflects the energy back to the interrogator. RFID has seen great proliferation in terrestrial inventory management applications, and it has recently made the jump to spaceflight applications onboard the International Space Station, augmenting an existing optical bar‐code infrastructure for tracking supplies. A number of advanced automated logistics management (ALM) concepts employing RFID are currently being developed and evaluated, including so‐called “smart” shelves, cubbies, and trash receptacles using low‐power, embeddable RFID interrogators. An infrastructure where both crew members and robotic assistants, such as autonomous free flyers, are similarly equipped with small RFID interrogators seems likely. It therefore behooves us to consider extending this infrastructure beyond ALM to applications such as low power, embedded sensing. Typically, data on an RFID tag can only be written by an RFID interrogator, using interrogator energy. In recent years, however, a few efforts have focused on using that energy to drive data acquisition from the tag IC, allowing the tag to modify its stored data sequence with sensor data before replying to an interrogator. In this way, the tag can act as a completely passive sensing device. One problem exists with this approach, however: the tag cannot gather data when an interrogator is not present. Thus, strictly passive RFID sensing tags cannot gather data at regular intervals, in the manner of a typical wireless sensor network, without careful, and impractical, planning of mobile interrogator movements. To address this shortcoming, we look to a recent advance in RFID technology which allows an external microprocessor to power the tag IC and write directly into its RFID memory using a wired serial interface. In this paradigm, data gathering is driven by a small, on‐board power supply (using batteries or harvested energy), and data transfer is provided passively through the RFID interrogation service. Since communication typically consumes the lion’s share of power in WSNs, such a technique has the potential to enable extremely long‐lived, embedded wireless sensing when used with extremely low‐current microcontrollers. Since the communication channel is only open when an interrogator is present and actively interrogating the RFID sensing tag, transport of periodically‐sampled sensor data presents itself as a delay/disruption‐tolerant networking (DTN) problem. In this paper, we present the design of a DTN‐like overlay on the common EPC Global, Class 1, Generation 2 RFID standard. This overlay allows seamless, guaranteed data transfer using the EPC Global protocol, supporting extremely low‐power, embedded sensing using an infrastructure likely to be already in place for ALM applications. We evaluate a prototype implementation of a complete end‐to‐end system using a robotic RFID interrogation agent, and we present future directions for the development of this sensing technique.

Raymond S. Wagner↗

Atmospheric corrections for satellite water quality studies

Variations in the relative value of the blue and green reflectances of a lake can be correlated with important optical and biological parameters measured from surface vessels. Measurement of the relative reflectance values from color film imagery requires removal of atmospheric effects. Data processing is particularly crucial because: (1) lakes are the darkest objects in a scene; (2) minor reflectance changes can correspond to important physical changes; (3) lake systems extend over broad areas in which atmospheric conditions may fluctuate; (4) seasonal changes are of importance; and, (5) effects of weather are important, precluding flights under only ideal weather conditions. Data processing can be accomplished through microdensitometry of scene shadow areas. Measurements of reflectance ratios can be made to an accuracy of plus or minus 12%, sufficient to permit monitoring of important eutrophication indices.

Piech, K. R.↗

Simulation of ASTER data using AVIRIS images

The Advanced Thermal Emission and Reflectance Radiometer (ASTER) is a joint Japanese/US imaging instrument scheduled to fly on the first Earth Observing System (EOS) platform in 1998. The complement of scanners includes a visible, three channel module with forward-looking stereo capability, a six channel short wavelength infrared module, and a five channel thermal module. As part of the definition phase for the instrument design, AVIRIS data was used to simulate the short wave infrared (SWIR) bands to investigate the effects of widening two of the bands to increase the signal-to-noise ratio (SNR) versus loss of spectral separability due to uncertainty in the post-launch band positions.

Abrams, Michael↗

Evaluation of data obtained from atmospheric laser Doppler velocimeter

The Doppler lidar velocimeter produces a variety of kinds of data. Besides the line of sight velocity components, there are the reflected amplitudes and the Doppler widths. Computer graphics software for displaying these data was produced. Different methods of presentation are needed for the various items. A picture was produced as pictures are often the best way to gain understanding. The individual lidar scans form a crosshatch pattern. Thus one-dimensional measurements fit together to form a two-dimensional whole. A pair of velocity measurements at a point combine to form a wind measurement with direction and magnitude. This gives a forest of wind vectors. The goal is to find a recognizable pattern to these trees. Often it is necessary to show only part of the information. That is, show only the wind direction not its magnitude or reduce the wind to streamlines of air flow. In other cases data are reduced to contour plots. Just enough contour lines are included to show the picture described.

Keck, T. S.↗

Detection techniques using multispectral data to index soil erosional status

Indexing techniques that can be used to detect soil erosion utilizing the known band widths of the Landsat MSS and TM sensors are identified. The indexing techniques focus on iron oxides, clays, and organic matter as properties revealing soil erosional status. For data aquisition, a Collins visible and infrared intelligent spectrometer was used to collect data from 0.4-24 microns. Pressed polytetrafluorethylene was used as the reflectance standard and was aquired at the same time that the sample data were aquired.

Pelletier, R. E.↗

Solar and atmospheric effects on satellite imagery derived from aircraft reflectance measurements

Solar and atmospheric effects on satellite imagery were investigated by measuring terrain reflectance from low-flying aircraft. Radiometric data were recorded over three test sites in California, Georgia, and South Dakota. Radiance from Skylab (EREP) S190A and ERTS-1 (Landsat-1) sensors was linearly correlated with wide-band terrain reflectance. The results support the proposition that the coefficients of the regression equation are the path radiance and a quantity representing the product of total irradiance and beam transmittance at the time of satellite overflight. These coefficients should be useful as linear conversion coefficients for extending spectral signatures in computer-aided classification work on satellite imagery.

Dana, R. W.↗

TRMM Validation: Integration of TRMM Satellite and Ground-Validation Data to Determine Tropical Heating

Steiner and Houze showed from ground validation data that the Tropical Rain Measuring Mission (TRMM) satellite Precipitation Radar's (PR's) twice daily only sampling should lead to an uncertainty of approximately 20% in rain estimates. They further showed that the uncertainties are smallest at the 5-7.5 km level. Schumacher and Houze used Kwajalein ground validation data to show that the TRMM PR misses only 2.3% of the near surface rainfall but does not see 46% of the area where rain occurs, because of the 17 dBZ PR reflectivity threshold. Houze discusses how the TRMM data extend earlier tropical convective studies to global coverage of the vertical profile of latent heating via the TRMM PR''s ability to distinguish and globally map convective and stratiform precipitation. Process studies carried out under this TRMM grant Yuter and Houze and Yuter et al. studied ship-based radar observations in the tropical eastern Pacific ITCZ. The eastern Pacific precipitation process is different from the western Pacific (the COARE area); rain is heavier but the clouds are not as deep. These process differences may affect the ability to remotely sense precipitation accurately in the two regions. Satellite microwave data were able to detect the precipitation as long as the rain areas exceeded 10 km in dimension. However, the microwave algorithms had difficulty distinguishing light and heavy rain. Satellite IR algorithms only partially detected the rain because the tops of the smaller and more short-lived rain clouds were sometimes not cold enough for the IR algorithms to detect them. Houze et al. focused on the west Pacific precipitating mesoscale convective systems and showed how their precipitation and internal dynamics vary in relation to the slowly varying large-scale heating-driven circulation, which has a structure described by a combination of Kelvin and Rossby wave response to the near-equatorial convective heating constituted by the mesoscale convective systems. Ship and aircraft radar data were used in this study.

Houze, Robert A., Jr.↗