Search NASA⌕ Search

SEARCH · Search NASA

Results for “wind engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Drag and Propulsive Characteristics of Air-Cooled Engine-Nacelle Installations for Large Airplanes, Special Report

An investigation is in progress in the NACA full-scale wind tunnel to determine the drag and propulsive efficiency of nacelle sizes. In contrast with the usual tests with a single nacelle, these tests were conducted with nacelle-propeller installations on a large model of a 4-engine airplane. Data are presented on the first part of the investigation, covering seven nacelle arrangements with nacelle diameters from 0.53 to 1.5 times the wing thickness. These ratios are similar to those occurring on airplane weighing from about 20 to 100 tons. The results show that the drag, the propulsive efficiency, and the overall efficiency of the various nacelle arrangements as functions of the nacelle size, the propeller position, and the airplane lift coefficient. The effect of the nacelles on the aerodynamic characteristics of the model are shown for both propeller-removed and propeller-operating conditions.

Silverstein, Abe↗

Noise reduction of a tilt-rotor aircraft including effects on weight and performance

Various methods for far-field noise reduction of a tilt-rotor acoustic signature and the performance and weight tradeoffs which result from modification of the noise sources are considered in this report. In order to provide a realistic approach for the investigation, the Boeing tilt-rotor flight research aircraft (Model 222), was selected as the baseline. This aircraft has undergone considerable engineering development. Its rotor has been manufactured and tested in the Ames full-scale wind tunnel. The study reflects the current state-of-the-art of aircraft design for far-field acoustic signature reduction and is not based solely on an engineering feasibility aircraft. This report supplements a previous study investigating reduction of noise signature through the management of the terminal flight trajectory.

Gibs, J.↗

Experimental Aerothermodynamics In Support Of The Columbia Accident Investigation

The technical foundation for the most probable damage scenario reported in the Columbia Accident Investigation Board's final report was largely derived from synergistic aerodynamic/aerothermodynamic wind tunnel measurements and inviscid predictions made at NASA Langley Research Center and later corroborated with engineering analysis, high fidelity numerical viscous simulations, and foam impact testing near the close of the investigation. This report provides an overview of the hypersonic aerothermodynamic wind tunnel program conducted at NASA Langley and illustrates how the ground-based heating measurements provided early insight that guided the direction and utilization of agency resources in support of the investigation. Global surface heat transfer mappings, surface streamline patterns, and shock shapes were measured on 0.0075 scale models of the Orbiter configuration with and without postulated damage to the thermal protection system. Test parametrics include angle of attack from 38 to 42 degs, sideslip angles of 38 to 42 degs, sideslip angles of plus or minus 1 deg, Reynolds numbers based upon model length from 0.05 x 10(exp 6) to 6.5 x 10(exp 6), and normal shock density ratios of 5 (Mach 6 Air) and 12 (Mach 6 CF4). The primary objective of the testing was to provide surface heating characteristics on scaled Orbiter models with outer mold line perturbations to simulate various forms of localized surface damage to the thermal protection system. Initial experimental testing conducted within two weeks of the accident simulated a broad spectrum of thermal protection system damage to the Orbiter windward surface and was used to refute several hypothesized forms of thermal protection system damage, which included gouges in the windward thermal protection system tiles, breaches through the wing new the main landing gear door, and protuberances along the wing leading edge that produced asymmetric boundary layer transition. As the forensic phase of the investigation developed and the condition of recovered debris was examined, increasing emphasis was placed on identifying wing leading edge damage (partially and fully missing reinforced carbon-carbon panels, and eventually holes in the wing leading edge with venting to the wing upper surface) that produced off-nominal heating trends consistent with extracted Orbiter flight recorder temperature data.

Horvath, Thomas J.↗

Mach 6 flowfield survey at the engine inlet of a research airplane

A flowfield survey was conducted to better define the nature of vehicle forebody flowfield at the inlet location of an airframe-integrated scramjet engine mounted on the lower surface of a high-speed research airplane to be air launched from a B-52 and rocket boosted to Mach 6. The tests were conducted on a 1/30-scale brass model in a Mach-6 20-in. wind tunnel at Reynolds number of 11,200,000 based on distance to engine inlet. Boundary layer profiles at five spanwise locations indicate that the boundary layer in the area of the forebody centerline is more than twice as thick as the boundary layer at three outboard stations. It is shown that the cold streak found in heating contours on the centerline of the forebody is caused by a thickening of the boundary layer on the centerline, and that this thickening decreases with angle of attack.

Johnson, C. B.↗

Inlet Unstart Propulsion Integration Wind Tunnel Test Program Completed for High-Speed Civil Transport

One of the propulsion system concepts to be considered for the High-Speed Civil Transport (HSCT) is an underwing, dual-propulsion, pod-per-wing installation. Adverse transient phenomena such as engine compressor stall and inlet unstart could severely degrade the performance of one of these propulsion pods. The subsequent loss of thrust and increased drag could cause aircraft stability and control problems that could lead to a catastrophic accident if countermeasures are not in place to anticipate and control these detrimental transient events. Aircraft system engineers must understand what happens during an engine compressor stall and inlet unstart so that they can design effective control systems to avoid and/or alleviate the effects of a propulsion pod engine compressor stall and inlet unstart. The objective of the Inlet Unstart Propulsion Airframe Integration test program was to assess the underwing flow field of a High-Speed Civil Transport propulsion system during an engine compressor stall and subsequent inlet unstart. Experimental research testing was conducted in the 10- by 10-Foot Supersonic Wind Tunnel at the NASA Glenn Research Center at Lewis Field. The representative propulsion pod consisted of a two-dimensional, bifurcated inlet mated to a live turbojet engine. The propulsion pod was mounted below a large flat plate that acted as a wing simulator. Because of the plate s long length (nominally 10-ft wide by 18-ft long), realistic boundary layers could form at the inlet cowl plane. Transient instrumentation was used to document the aerodynamic flow-field conditions during an unstart sequence. Acquiring these data was a significant technical challenge because a typical unstart sequence disrupts the local flow field for about only 50 msec. Flow surface information was acquired via static pressure taps installed in the wing simulator, and intrusive pressure probes were used to acquire flow-field information. These data were extensively analyzed to determine the impact of the unstart transient on the surrounding flow field. This wind tunnel test program was a success, and for the first time, researchers acquired flow-field aerodynamic data during a supersonic propulsion system engine compressor stall and inlet unstart sequence. In addition to obtaining flow-field pressure data, Glenn researchers determined other properties such as the transient flow angle and Mach number. Data are still being reduced, and a comprehensive final report will be released during calendar year 2000.

Porro, A. Robert↗

The value of in-reservoir energy storage for flexible dispatch of geothermal power

Geothermal systems making use of advanced drilling and well stimulation techniques have the potential to provide tens to hundreds of gigawatts of clean electricity generation in the United States by 2050. With near-zero variable costs, geothermal plants have traditionally been envisioned as providing “baseload” power, generating at their maximum rated output at all times. However, as variable renewable energy sources (VREs) see greater deployment in energy markets, baseload power is becoming increasingly less competitive relative to flexible, dispatchable generation and energy storage. Herein we conduct an analysis of the potential for future geothermal plants to provide both of these services, taking advantage of the natural properties of confined, engineered geothermal reservoirs to store energy in the form of accumulated, pressurized geofluid and provide flexible load-following generation. We develop a linear optimization model based on multi-physics reservoir simulations that captures the transient pressure and flow behaviors within a confined, engineered geothermal reservoir. We then optimize the investment decisions and hourly operations of a power plant exploiting such a reservoir against a set of historical and modeled future electricity price series. Further, we find that operational flexibility and in-reservoir energy storage can significantly enhance the value of geothermal plants in markets with high VRE penetration, with energy value improvements of up to 60% relative to conventional baseload plants operating under identical conditions. Across a range of realistic subsurface and operational conditions, our modeling demonstrates that confined, engineered geothermal reservoirs can provide large and effectively free energy storage capacity, with round-trip storage efficiencies comparable to those of leading grid-scale energy storage technologies. Optimized operational strategies indicate that flexible geothermal plants can provide both short- and long-duration energy storage, prioritizing output during periods of high electricity prices. Sensitivity analysis assesses the variation in outcomes across a range of subsurface conditions and cost scenarios.

15 GEOTHERMAL ENERGY↗

Investigation of grid-based vorticity-velocity large eddy simulation off-body solvers for application to overset CFD

Accurately predicting unsteady wakes and vortex-dominated flows is essential to a wide range of engineering applications, including aircraft, rotorcraft, shipboard operations, bio-inspired unsteady flight and propulsion, wind turbines, and urban flows. While current CFD software can model the complete flow field and wake system, the computational costs incurred in high Reynolds number unsteady turbulent flow simulations often remain prohibitive for routine engineering use, particularly for applications involving moving components. Prior work has demonstrated that by adopting a vorticity-velocity formulation in a grid-based off-body flow solver (VorTran-M and VorTran-M2) one can lower these costs by several orders of magnitude when compared to conventional approaches. This paper describes the extensions made to VorTran-M2 to support turbulent flows, and associated benchmarking activity to assess its performance for problems involving strong stretching and diffusion processes, whose competing contributions to the vorticity field are core drivers of turbulent flow evolution. Predictions are presented for: (i) the Kida-Pelz problem whose inviscid form is of mathematical interest due to its apparent formation of singular flow in finite time; and (ii) the Taylor Green vortex arrangement, which has been extensively studied as a fundamental simulation challenge in the turbulent modeling community. Here, the results are used to evaluate the overall predictive ability and performance of two sub-grid scale models incorporated into VorTran-M2. Results indicate that the computational cost savings seen previously for inviscid and convection dominated problems extend to turbulent flow simulations supporting the viability of VorTran-M2 as a low cost means for accurately modeling the far-field and background flow, particularly when long duration vorticity evolution is of interest.

42 ENGINEERING↗

Wind Alliance for the Sustainable Development

The Puerto Rico Energy Affairs Administration (PREAA) is actively engaged in the implementation of existing public policy for the conservation of energy and promotion of renewable energy to reduce consumer’s costs and reduce environmental impact. Puerto Rico is an island in where no own reserves of gas, oil or coal exists. This severe dependence in on foreign oil is reflected in the higher cost of electricity in Puerto Rico, which is significantly higher than most of the United States. Therefore, public energy policy of Puerto Rico places emphasis on diversification of energy sources and the use of renewable energy technologies. The Wind energy Alliance for the Sustainable Development project focused on the formation of a wind energy working group to educate and promote wind energy technologies; at the same time the evaluating the viability of wind energy in Puerto Rico. The educational outreach was performed through a series of wind energy workshops where interested parties such as, installers, sellers, engineers, general public even opposing groups participate from the activities.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Development of a Planar Focusing Collector for CSP

In the field of the concentrating solar power (CSP) technology, the parabolic trough is a common choice for a solar collector. Parabolic troughs are highly reflective curved mirrors that take incident sunlight and focus it onto a line-shaped receiver that runs down the center of troughs. The receivers are generally heat-absorbing pipes containing a heat transfer fluid that delivers the collected thermal energy to steam turbines or engines for generating electricity. However, parabolic troughs are constrained by wind loads and cost of materials and support structure. The goal of this project was to develop a planar focusing collector (PFC) that would serve as an alternative to the parabolic trough. An ideal PFC is ultrathin (less than a few microns) and lightweight, and could be manufactured in a manner that is scalable and low cost. Furthermore, these features would be attractive to CSP technology because of the potential to reduce cost and complexity of installation and maintenance. The work pursued in this project attempted to actualize the PFC concept by utilizing advances in the emerging area of metasurfaces, which rely on the nanopatterning of surfaces to control the amplitude and phase of light at length scales smaller than an optical wavelength. Academic pursuits of metasurface technology predominately employ electron-beam lithography (EBL) for fabrication because the technique offers highly reliable nanopatterning of surfaces with a spatial resolution of ~10 nm. However, due to the techno-economic constraints of the DOE’s SunShot program, particularly cost-effective scalability, the use of EBL was avoided in this project. Rather, fabrication approaches that lend themselves to scalable manufacturing by way of stamping or imprinting were favored. Ultimately, the tradeoffs with using such methods was the larger feature size—on the order of ~150 um critical dimension—resulting in poorer control of light compared to structures fabricated by EBL. A summary of our 2-year investigation on this topic is presented herein. We begin by presenting highlights of our 1 st -year efforts using plasmonics, i.e., metallic nanostructures, as the building block for our PFC. The limitations in this approach are subsequently summarized. We then review the strategy we employed during the final year of our project, in particular utilizing insulating or dielectric materials as the light controlling medium. We round out the report discussing the results of our findings from using this approach. The report is relatively self-contained in that and no prior knowledge of optics or nanotechnology is assumed and technical jargon is kept at a minimum.

14 SOLAR ENERGY↗

North American Renewables Integration Study (NARIS): Cooperative Research and Development Final Report, CRADA Number CRD-16-00633

The goal of the study is to help inform and assist power system planning entities, electricity system operators, government energy agencies, legislators and regulators to better understand the planning, engineering, operational, and economic implications of integrating large amounts of wind, solar and hydro energy into the Canadian, US and Mexican electrical systems.

14 SOLAR ENERGY↗

Design, Manufacture, and Testing of an Open-Source Benchmark Composite Hydrokinetic Turbine Blade: Preprint

In a trend toward clean energy alternatives, recent years have seen great strides in the marine energy space. Consequently, there is a pressing need for the design, development, and validation of novel energy harvesting technologies such as hydrokinetic devices, which capture kinetic energy from waves, tides, and currents. However, these devices span numerous concepts and designs that often lack solid benchmark research that can be freely referenced throughout their development. This work focuses on the design process of an open-source composite hydrokinetic turbine blade for a three-bladed marine turbine rotor assembly with a diameter of 2.5 m. The proposed blade consists of two structural composite skins that are bonded with an adhesive and filled with a foam core. This study also explores and contrasts the efficiency and resolution of low-fidelity rapid design methodologies and comprehensive high-fidelity approaches in the context of blade design, modeling, and analysis efforts, a key objective in this research. Blade hydrodynamic loads were modeled and applied to finite-element blade models to study deformations and potential failure. Ongoing and upcoming efforts will result in blade manufacture and structural testing at the National Renewable Energy Laboratory. In future work, multiple blades will be deployed at the Living Bridge site at the University of New Hampshire and will be compared to rigid aluminum blades of the same geometry, developed by Sandia National Laboratories. Ultimately, this research will lay foundational groundwork for researchers and manufacturers, establishing a baseline composite blade design that will serve as a benchmark in the development of future hydrokinetic turbine blades.

blade design↗

Space Shuttle: Static pressure distribution on Chrysler Corporation Space Division SERV booster configuration

A dual purpose test was conducted in the propulsion wind tunnel (PWT) to evaluate the performance of an aerospike engine, in the presence of a booster, and obtain forebody and base pressure distributions on the booster in which it is installed. The test item was a 2.5 percent scaled replica of the SERV booster employing a 5 percent spike length aerospike engine installed in the base region of the model. Cold flow air was used to simulate engine jet operation. Two booster configurations were investigated, one on which reentry aerospike engine thermal protection doors were installed, and another where the doors were removed. The data presented are representative of the latter configuration for a Mach number range of 0 to 1.25 at angles of attack of 0 and 8 degrees and 0 degrees angle of sideslip.

Price, E. A.↗

Nitrogen fixation studies, lead detection in living plants, and solar wind analysis

Progress is reported for research on the following: (1) magnetically shielded test facility studies; (2) electrochemistry of B10C2H12, B9CH10(-), and preparation of tumor specific boron containing materials for use in cancer therapy; (3) histochemical method for determining lead in living plant tissue; (4) diamond cementing; (5) analysis of solar wind using the washings of lunar fines; and (6) environmental engineering.

Libby, W. F.↗

Hypersonic research engine project. Phase 2: Structures and cooling development

The flightweight components were adapted to form the basic engine assembly. The water cooled test adapters for use in wind tunnel tests were fabricated. Commercially available valves were selected for the coolant control system. The simplification of the temperature control concept and of the absence of weight and volume constraints made it possible to use these valves. Various calibration tests are also discussed.

Jilly, L. F.↗

Advanced control concepts

The selection of a trim solution that provides the space shuttle with the highest level of performance and dynamic control in the presense of wind disturbances and bias torques due to misalignment of rocket engines is described. It was determined that engine gimballing is insufficient to provide control to trim the vehicle for headwind and sidewind disturbances, and that it is necessary to use aerodynamic surfaces in conjunction with engine gimballing to achieve trim. The algebraic equations for computing the trim solution were derived from the differential equations describing the motion of the vehicle by substituting the desired trim conditions. The general problem of showing how the trim equations are derived from the equations of motion and the mathematical forms of the performance criterion is discussed in detail, along with the general equations for studying the dynamic response of the trim solution.

Hutton, M. F.↗

Acoustic-loads research for powered-lift configurations

Data presented from large-scale model tests with jet engines having thrusts of 9 kN (2000 lb) and 36 kN (8000 lb) include acoustic loads for an externally blown wing and flap induced by a TF34 jet engine, an upper surface blown (USB) aircraft model in a wind tunnel, and two USB models in static tests. Comparisons of these results with results from acoustic loads studies on configurations of other sizes are made and the implications of these results on interior noise and acoustic fatigue are discussed.

Schoenster, J. A.↗

Effect of forward velocity and crosswind on the reverse-thrust performance of a variable-pitch fan engine

A full-size variable-pitch fan engine was tested in the Ames 40 by 80 foot wind tunnel to determine the effect of forward velocity and crosswind on reverse-thrust performance. Two flight-type inlet configurations were tested, and a flared fan nozzle was installed as an inlet for reverse-thrust operation. Steady-state reverse-thrust performance was obtained up to 54 m/s (105 knots). An abrupt decrease in reverse thrust occurred at about 30 m/s (60 knots). Reverse thrust was established following forward-to-reverse thrust transients both statically and with forward velocities only up to 30 m/s.

Reemsnyder, D. C.↗

Phase 1 wind tunnel tests of the J-97 powered, external augmentor V/STOL model

Test results are presented for a large scale, external augmentor V/STOL model in a 40 ft by 80 ft wind tunnel. The model was powered by a GE J97 engine and featured longitudinal ejectors alongside and external to the fuselage together with an augmentor flap on the low aspect ratio, double-delta wing. A static thrust augmentation ratio of 1.60 was measured for the fuselage augmentor at a nozzle pressure ratio of 3.0 and a nozzle exhaust gas temperature of 700 C. At forward speed the model showed a strong positive lift interference due to the augmentor flap, and a marked absence of negative lift interference due to the fuselage augmentor jet system. The nose-up moment of the fuselage augmentor inlet flow was approximately cancelled by a 60 deg deflection of the augmentor flap. An assessment of the thrust and drag components to allow the prediction of transition performance of aircraft designs based on the present conceptual model was made. Lateral tests showed strong but well ordered effects of power.

Garland, D. B.↗