Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSIBILITY EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

The Effect of Hole Quality on the Fatigue Life of 2024-T3 Aluminum Alloy Sheet

This paper presents the results of a study whose main objective was to determine which type of fabrication process would least affect the fatigue life of an open-hole structural detail. Since the open-hole detail is often the fundamental building block for determining the stress concentration of built-up structural parts, it is important to understand any factor that can affect the fatigue life of an open hole. A test program of constant-amplitude fatigue tests was conducted on five different sets of test specimens each made using a different hole fabrication process. Three of the sets used different mechanical drilling procedures while a fourth and fifth set were mechanically drilled and then chemically polished. Two sets of specimens were also tested under spectrum loading to aid in understanding the effects of residual compressive stresses on fatigue life. Three conclusions were made from this study. One, the residual compressive stresses caused by the hole-drilling process increased the fatigue life by two to three times over specimens that were chemically polished after the holes were drilled. Second, the chemical polishing process does not appear to adversely affect the fatigue life. Third, the chemical polishing process will produce a stress-state adjacent to the hole that has insignificant machining residual stresses.

Everett, Richard A., Jr.↗

Room and Low Temperature Performance of High-Speed Neural Network Circuits

We have described a challenging neural-network hardware implementation that would mate a 64x64-pixel infrared sensor directly on to a 3-dimensionally packaged set of neural processing chips with parallel input for high speed image processing. Non linearity effects and range compression are also discussed.

high-speed neural network circuits neural network ↗

Aerothermodynamic Testing of Protuberances and Penetrations on the NASA Crew Exploration Vehicle Heat Shield in the NASA Langley 20-Inch Mach 6 Air Tunnel

An experimental wind tunnel program is being conducted in support of an Agency wide effort to develop a replacement for the Space Shuttle and to support the NASA s long-term objective of returning to the moon and then on to Mars. This paper documents experimental measurements made on several scaled ceramic heat transfer models of the proposed Crew Exploration Vehicle. Global heat transfer images and heat transfer distributions obtained using phosphor thermography were used to infer interference heating on the Crew Exploration Vehicle Cycle 1 heat shield from local protuberances and penetrations for both laminar and turbulent heating conditions. Test parametrics included free stream Reynolds numbers of 1.0x10(exp 6)/ft to 7.25x10(exp 6)/ft in Mach 6 air at a fixed angle-of-attack. Single arrays of discrete boundary layer trips were used to trip the boundary layer approaching the protuberances/penetrations to a turbulent state. Also, the effects of three compression pad diameters, two radial locations of compression pad/tension tie location, compression pad geometry, and rotational position of compression pad/tension tie were examined. The experimental data highlighted in this paper are to be used to validate CFD tools that will be used to generate the flight aerothermodynamic database. Heat transfer measurements will also assist in the determination of the most appropriate engineering methods that will be used to assess local flight environments associated with protuberances/penetrations of the CEV thermal protection system.

Liechty, Derek S.↗

PLIF Visualization of Active Control of Hypersonic Boundary Layers Using Blowing

Planar laser-induced fluorescence (PLIF) imaging was used to visualize the boundary layer flow on a 1/3-scale Hyper-X forebody model. The boundary layer was perturbed by blowing out of orifices normal to the model surface. Two blowing orifice configurations were used: a spanwise row of 17-holes spaced at 1/8 inch, with diameters of 0.020 inches and a single-hole orifice with a diameter of 0.010 inches. The purpose of the study was to visualize and identify laminar and turbulent structures in the boundary layer and to make comparisons with previous phosphor thermography measurements of surface heating. Jet penetration and its influence on the boundary layer development was also examined as was the effect of a compression corner on downstream boundary layer transition. Based upon the acquired PLIF images, it was determined that global surface heating measurements obtained using the phosphor thermography technique provide an incomplete indicator of transitional and turbulent behavior of the corresponding boundary layer flow. Additionally, the PLIF images show a significant contribution towards transition from instabilities originating from the underexpanded jets. For this experiment, a nitric oxide/nitrogen mixture was seeded through the orifices, with nitric oxide (NO) serving as the fluorescing gas. The experiment was performed in the 31-inch Mach 10 Air Tunnel at NASA Langley Research Center.

Bathel, Brett F.↗

Dual-Pump CARS Development and Application to Supersonic Combustion

A dual-pump Coherent Anti-Stokes Raman Spectroscopy (CARS) instrument has been developed to obtain simultaneous measurements of temperature and absolute mole fractions of N2, O2 and H2 in supersonic combustion and generate databases for validation and development of CFD codes. Issues that compromised previous attempts, such as beam steering and high irradiance perturbation effects, have been alleviated or avoided. Improvements in instrument precision and accuracy have been achieved. An axis-symmetric supersonic combusting coaxial jet facility has been developed to provide a simple, yet suitable flow to CFD modelers. Approximately one million dual-pump CARS single shots have been collected in the supersonic jet for varying values of flight and exit Mach numbers at several locations. Data have been acquired with a H2 co-flow (combustion case) or a N2 co-flow (mixing case). Results are presented and the effects of the compressibility and of the heat release are discussed.

Magnotti, Gaetano↗

Twinned magnetite in granitic samples from the Siljan impact structure, Sweden

Impact cratering is a ubiquitous process throughout the solar system and has played a key role for the geologic evolution of Earth and other planets [1]. Magnetic anomalies are common characteristics of impact craters [2], so understanding how magnetite (Fe23+Fe2+O42-), an important magnetic carrier in both terrestrial and extraterrestrial rocks, is affected by shock waves, especially structurally and magnetically, is crucial. Magnetic minerals have been studied to gain insight into the geologic evolution of Mars, with specific focus including understanding the Martian crustal structure and the oxidization state of Martian rocks (e.g., [3,4,5]). Shock waves permanently alter the intrinsic magnetic properties of rocks (e.g., [6]), as do twinning in natural environments with less extreme P/T conditions [7]. In fact, pressure conditions induced by impacts have been suggested to explain demagnetization signatures observed around Martian impact basins [8]. It is still poorly understood what effects shock has on the crystallographic structure of magnetite and thus it’s intrinsic magnetic properties, and , how that affects the bulk magnetic properties of rocks (e.g., [9]). Limited experimental studies have investigated the effects of shock compression on magnetite, especially with the aim of describing crystallographic deformation (e.g., [9] and references therein). In this work we report preliminary results of an investigation of microstructures in magnetite, an “unconventional” mineral in shock studies, in granitic samples from the ca. 380 Ma ~52 km-in-diameter Siljan impact structure, located in south-central Sweden.

shock metamorphism↗

Sealing Europa’s Vents By Vapor Deposition: An Order-of-Magnitude Study

Fractures and vents in the ice crust of Europa, exposing the sub-surface ocean or liquid-water inclusions to the vacuum, might be responsible for the generation of planetary-scale water-vapor plumes. During its passage through the ice, the plume vapor is expected to partially condense on the cold ice walls. Together with other effects (water spillage, compression forces, etc.) this mechanism likely contributes to sealing the vent. In this work, we develop a lumped-parameter model to analyze the sealing timescales associated to water-vapor deposition alone. Neglecting all other possible mechanisms, we find shutting-off times roughly compatible with the 7-hour plume observed in 2012 by the Hubble Space Telescope, suggesting that vapor deposition might have played a major role in sealing the vent. A map of sealing times vs. plume density, mass flow rate and aperture areas is given. Plume quantities from the literature are analyzed and compared to our results. For a given plume density/mass flow rate, small apertures would be sealed quickly by vapor deposition and are thus incompatible with observations.

Europa↗

Graphite-epoxy panel compression strength reduction due to local impact

A review of results from on-going research to investigate the effects of low-velocity impact on the compressive strength of graphite-epoxy structures is presented. Extensive tests have been conducted on sandwich beams, laminated plates and stiffened panels. Conditions for failures were investigated by impact tests on statically loaded test specimens. The effects of compression load intensity were such that lightly loaded graphite structures (such as aircraft secondary structure) were insensitive to impact damage. In more heavily loaded structures, (such as wing panels), however, appreciable reductions in compressive strength occurred. The implications of the tests for structural design are discussed by comparing panel masses for designs where ultimate strains have been reduced due to impact considerations with the masses of designs with higher ultimate strains. Finally, preliminary test data is presented to show the possibility of improvements in damage tolerance achievable by using an alternate matrix material.

Card, M. P.↗

Turbulent Compressible Convection with Rotation: Flow Structure and Evolution - Part 1

The effects of Coriolis forces on compressible convection are studied using three-dimensional numerical simulations carried out within a local modified f-plane model. The physics is simplified by considering a perfect gas occupying a rectilinear domain placed tangentially to a rotating sphere at various latitudes, through which a destabilizing heat flux is driven. The resulting convection is considered for a range of Rayleigh, Taylor, and Prandtl (and thus Rossby) numbers, evaluating conditions where the influence of rotation is both weak and strong. Given the computational demands of these high-resolution simulations, the parameter space is explored sparsely to ascertain the differences between laminar and turbulent rotating convection. The first paper in this series examines the effects of rotation on the flow structure within the convection, its evolution, and some consequences for mixing. Subsequent papers consider the large-scale mean shear flows that are generated by the convection, and the effects of rotation on the convective energetics and transport properties. It is found here that the structure of rotating turbulent convection is similar to earlier nonrotating studies, with a laminar, cellular surface network disguising a fully turbulent interior punctuated by vertically coherent structures. However, the temporal signature of the surface flows is modified by inertial motions to yield new cellular evolution patterns and an overall increase in the mobility of the network. The turbulent convection contains vortex tubes of many scales, including large-scale coherent structures spanning the full vertical extent of the domain involving multiple density scale heights. Remarkably, such structures align with the rotation vector via the influence of Coriolis forces on turbulent motions, in contrast with the zonal tilting of streamlines found in laminar flows. Such novel turbulent mechanisms alter the correlations which drive mean shearing flows and affect the convective transport properties. In contrast to this large-scale anisotropy, small-scale vortex tubes at greater depths are randomly orientated by the rotational mixing of momentum, leading to an increased degree of isotropy on the medium to small scales of motion there. Rotation also influences the thermodynamic mixing properties of the convection. In particular, interaction of the larger coherent vortices causes a loss of correlation between the vertical velocity and the temperature leaving a mean stratification which is not isentropic.

Brummell, Nicholas H.↗

Effects of radiation damage and precipitate distribution on micro-pillar compression testing of irradiated CuCrZr

The results of small-scale mechanical tests are convoluted by the so-called size effect, whereby materials appear stronger when the scale of the test is reduced to the order of microns or less. The dimensional range over which this occurs has been shown to be linked to a change in sample microstructure, such as the addition of defects induced by irradiation. To investigate this response, a CuCrZr alloy was subjected to proton irradiation and mechanically tested using micro compression of pillars with a range in size. It was found that irradiation defects dominate over the extrinsic size effect and the sensitivity to differences in precipitate microstructure was also somewhat reduced, suggesting that size-independent results could be obtained from much smaller test volumes in irradiated material compared to their non-irradiated counterparts. Lastly, comparison was made between the increase in yield strength predicted by models and the experimentally measured values to establish the key parameters driving the strengthening behaviour.

36 MATERIALS SCIENCE↗

Filamentary pulse self-compression: The impact of the cell windows

Self-compression of multi-millijoule laser pulses during filamentary propagation is usually explained by the interplay of self-focusing and defocusing effects, causing a substantial concentration of energy on the axis of the propagating optical pulse. Recently, it has been argued that cell windows may play a decisive role in the self-compression mechanism. As such windows have to be used for media other than air their presence is often unavoidable, yet they present a sudden nonadiabatic change in dispersion and nonlinearity that should lead to a destruction of the temporal and spatial integrity of the light bullets generated in the self-compression mechanism. We now experimentally prove that there is, in fact, a self-healing mechanism that helps to overcome the potentially destructive consequences of the cell windows. We show in two carefully conducted experiments that the cell window position decisively influences activation or inhibition of the self-healing mechanism. A comparison with a windowless cell shows that the presence of this mechanism is an important prerequisite for the exploitation of self-compression effects in windowed cells filled with inert gases.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of isoalcohol blending with gasoline on autoignition behavior in a rapid compression machine: Isopropanol and isobutanol

Alcohols, and particularly isoalcohols, are potentially advantageous blendstocks towards achieving efficient, low-carbon intensity internal combustion engines. Their use in advanced configurations, such as boosted spark-ignition or spark-assisted compression ignition, requires a comprehensive understanding of their blending effects on the low- and intermediate-temperature autoignition behavior of petroleum-derived gasoline. This work reports an experimental and modeling study of such autoignition characteristics quantified in a twin-piston rapid compression machine. Isopropanol and isobutanol are blended into a research-grade gasoline (FACE-F) at oxygenate blend levels of 0 to 30% vol/vol, with tests conducted at pressures of 20 and 40 bar, temperatures from 700 to 1000 K, and dilute stoichiometric fuel loadings. Changes to overall reactivity, including first-stage and main ignition times, and preliminary exothermicity are established, with comparisons made to previous measurements with ethanol-blended FACE-F gasoline. Furthermore, it is found that at low-temperature/NTC conditions (700–860 K) the isoalcohols suppress first-stage reactivity and associated heat release while main ignition times are extended. At NTC/intermediate-temperature (860–1000 K) conditions changes to fuel reactivity are less significant with isopropanol slightly suppressing reactivity and isobutanol promoting ignition. Detailed chemical kinetic modeling is used to interpret the experimental measurements. Overall trends of suppression or promotion in the blending behavior are reasonably captured by the model. Sensitivity and rate of production analyses indicate that at lower temperatures H-atom abstraction reactions from the surrogate fuel molecules (e.g., cyclopentane, isooctane) and the isoalcohols via OH are important leading to TC 3 H 6 OH and IC 4 H 8 OH–C radicals, for isopropanol and isobutanol respectively, which act as scavengers in the system. At higher temperatures, similar chemistries are dominant, but there is an increasing importance of abstraction by HO 2 . The kinetic modeling also indicates that the promoting effect of isobutanol at higher temperatures is due to the increased abstractions at the γ-sites, while at lower temperatures abstraction at the α-site leads to greater reactivity suppression.

36 MATERIALS SCIENCE↗

Impact of Pore Fluid Chemistry on Fine-Grained Sediment Fabric and Compressibility

Fines, defined here as grains or particles, less than 75µm in diameter, exist nearly ubiquitously in natural sediment, even those classified as coarse. Macroscopic sediment properties, such as compressibility, which relates applied effective stress to the resulting sediment deformation, depend on the fabric of fines. Unlike coarse grains, fines have sizes and masses small enough to be more strongly influenced by electrical interparticle forces than by gravity. These electrical forces acting through pore fluids are influenced by pore-fluid chemistry changes. Macroscopic property dependence on pore-fluid chemistry must be accounted for in sediment studies involving subsurface flow and sediment stability analyses, as well as in engineered flow situations such as groundwater pollutant remediation, hydrocarbon migration or other energy resource extraction applications. This study demonstrates how the liquid-limit-based electrical sensitivity index can be used to predict sediment compressibility changes due to pore-fluid chemistry changes. Laboratory tests of electrical sensitivity, sedimentation and compressibility illustrate mechanisms linking micro- and macro-scale processes for selected pure, endmember fines. In conclusion, a specific application considered here is methane extraction via depressurization of gas hydrate-bearing sediment, which causes a dramatic pore-water salinity drop concurrent with sediment being compressed by the imposed effective stress increase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The strainrange conversion principle for treating cumulative fatigue damage in the creep range

A formula is derived for combining effects of successive hysteresis loops in the creep range of materials when one loop has excess tensile creep, while the other contains excess compressive creep. The resultant effect resembles single loops involving balanced tensile and compressive creep. The attempt to use the Interaction Damage Rule as a tool in combining loops of non-equal size and complex strainrange content has led to important new concepts useful in future studies of creep-fatigue. It turns out that the Interaction Damage Rule is basically an expression of how a set of hysteresis loops involving only single generic strains can combine to produce the same micromechanistic damage as the loop containing the combined strainranges which it analyzes. Making use of the underlying concept of Strainrange Partitioning that only the strainrange content of a hysteresis loop governs fatigue life, not order of introducing strainranges, a rational derivation of the Interaction Damage Rule is provided, showing also how it can effectively be used to synthesize independent loops and determine both damaging and healing effects.

Manson, S. S.↗

Calculation of particle dynamics effects on laser velocimeter data

In order to analytically assess the effects of particle dynamics on laser velocimeter measurements, the particle response to the fluid in which it is entrained must be modeled. The equation of particle motion derived at Arnold Engineering and Development Center (AEDC), is used to model the motion of the particle. The equation is derived from the Navier-Stokes equation under the assumption of unsteady Stokes flow. It should be noted that the Stokes flow eliminates the need for a far field boundary condition, and hence eliminates any normal (lift) forces. To extend the equation to higher particle slip velocities, the Stokes drag is replaced with the particle drag law, modified to include heat transfer effects. The drag coefficient accounts for inertial, rarefaction, compressibility, shape, and heat transfer effects.

Nichols, R. H.↗

Factors affecting the thermal shock behavior of yttria stabilized hafnia based graphite and tungsten composites.

Hafnia-based composites containing either graphite or tungsten were investigated as rocket nozzle throat inserts in solid propellant rocket engines. The thermal shock resistance of these materials is considered in terms of macroscopic thermal conductivity, thermal expansion, modulus of elasticity, and compressive fracture stress. The effect of degree of hafnia stabilization, density, and graphite or tungsten content upon these parameters is discussed. The variation of the ratio of elastic modulus to compressive fracture stress with density and its effect upon thermal shock resistance of these materials are discussed in detail.

Lineback, L. D.↗

SU-F-T-91: Development of Real Time Abdominal Compression Force (ACF) Monitoring System

Purpose: Hard-plate based abdominal compression is known to be effective, but no explicit method exists to quantify abdominal compression force (ACF) and maintain the proper ACF through the whole procedure. In addition, even with compression, it is necessary to do 4D CT to manage residual motion but, 4D CT is often not possible due to reduced surrogating sensitivity. In this study, we developed and evaluated a system that both monitors ACF in real time and provides surrogating signal even under compression. The system can also provide visual-biofeedback. Methods: The system developed consists of a compression plate, an ACF monitoring unit and a visual-biofeedback device. The ACF monitoring unit contains a thin air balloon in the size of compression plate and a gas pressure sensor. The unit is attached to the bottom of the plate thus, placed between the plate and the patient when compression is applied, and detects compression pressure. For reliability test, 3 volunteers were directed to take several different breathing patterns and the ACF variation was compared with the respiratory flow and external respiratory signal to assure that the system provides corresponding behavior. In addition, guiding waveform were generated based on free breathing, and then applied for evaluating the effectiveness of visual-biofeedback. Results: We could monitor ACF variation in real time and confirmed that the data was correlated with both respiratory flow data and external respiratory signal. Even under abdominal compression, in addition, it was possible to make the subjects successfully follow the guide patterns using the visual biofeedback system. Conclusion: The developed real time ACF monitoring system was found to be functional as intended and consistent. With the capability of both providing real time surrogating signal under compression and enabling visual-biofeedback, it is considered that the system would improve the quality of respiratory motion management in radiation therapy. This research was supported by the Mid-career Researcher Program through NRF funded by the Ministry of Science, ICT & Future Planning of Korea (NRF-2014R1A2A1A10050270) and by the Radiation Technology R&D program through the National Research Foundation of Korea funded by the Ministry of Science, ICT & Future Planning (No. 2013M2A2A7038291)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗