Search NASA⌕ Search

SEARCH · Search NASA

Results for “Capture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Optimization of water use and cost of electricity for an MEA carbon capture process, January 26, 2012

DOE goals are: 90% CO{sub 2} capture, Less than 30% increase in COE, and to reduce water use by 70% at 50% cost of dry cooling. Objectives are: (1) Develop detailed models of supercritical power plant, MEA carbon capture process, CO{sub 2} compression; and (2) Optimize process for conflicting goals of minimizing water use and COE CO{sub 2} capture greatly increases COE and water use, power gen. 1/3 of fresh water use, and water scarcity is increasing.

97 MATHEMATICS AND COMPUTING↗

Modeling and optimization of a modified claus process as part of an integrted gasification combined cycle (IGCC) power plant with CO2 capture

The modified Claus process is one of the most common technologies for sulfur recovery from acid gas streams. Important design criteria for the Claus unit, when part of an Integrated Gasification Combined Cycle (IGCC) power plant, are the ability to destroy ammonia completely and recover sulfur thoroughly from a relatively low purity acid gas stream without sacrificing flame stability. Due to these criteria, modifications are often required to the conventional process, resulting in a modified Claus process. For the studies discussed here, these modifications include the use of a 95% pure oxygen stream as the oxidant, a split flow configuration, and the preheating of the feeds with the intermediate pressure steam generated in the waste heat boiler (WHB). In the future, for IGCC plants with CO2 capture, the Claus unit must satisfy emission standards without sacrificing the plant efficiency in the face of typical disturbances of an IGCC plant such as rapid change in the feed flowrates due to load-following and wide changes in the feed composition because of changes in the coal feed to the gasifier. The Claus unit should be adequately designed and efficiently operated to satisfy these objectives. Even though the Claus process has been commercialized for decades, most papers concerned with the modeling of the Claus process treat the key reactions as equilibrium reactions. Such models are validated by manipulating the temperature approach to equilibrium for a set of steady-state operating data, but are of limited use for dynamic studies. One of the objectives of this study is to develop a model that can be used for dynamic studies. In a Claus process, especially in the furnace and the WHB, many reactions may take place. In this work, a set of linearly independent reactions has been identified and kinetic models of the furnace flame and anoxic zones, WHB, and catalytic reactors have been developed. To facilitate the modeling of the Claus furnace, a four-stage method was devised so as to determine which set of linearly independent reactions would best describe the product distributions from available plant data. Various approaches are taken to derive the kinetic rate expressions which are either missing in the open literature or found to be inconsistent. A set of plant data is used for optimal estimation of the kinetic parameters. The final model agrees well with the published plant data. Using the developed kinetics models of the Claus reaction furnace, WHB, and catalytic stages, two optimization studies are carried out. The first study shows that there exists an optimal steam pressure generated in the WHB that balances hydrogen yield, oxygen demand, and power generation. In the second study, it is shown that an optimal H2S/SO2 ratio exists that balances single-pass conversion, hydrogen yield, oxygen demand, and power generation. In addition, an operability study has been carried out to examine the operating envelope in which both H2S/SO2 ratio and adiabatic flame temperature can be controlled in the face of disturbances typical for the operation of an IGCC power plant with CO2 capture. Impact of CO2 capture on the Claus process has also been discussed.

08 HYDROGEN↗

Wide-Bandwidth Capture of Wire-Scanner Signals

Integrated charge collected on the sense wires of wire-scanner systems utilized to determine beam profile is generally the parameter of interest. The LANSCE application requires capturing the charge information macropulse-by-macropulse with macropulse lengths as long as 700 {micro}s at a maximum macropulse rate of 120 Hz. Also, for the LANSCE application, it is required that the integration be performed in a manner that does not require integrator reset between macropulses. Due to the long macropulse which must be accommodated and the 8.33 ms minimum pulse period, a simple R-C integrator cannot be utilized since there is insufficient time between macropulses to allow the integrator to adequately recover. The application of wide analog bandwidth to provide accurate pulse-by-pulse capture of the wire signals with digital integration of the wire signals to determine captured charge at each macropulse in applications with comparatively long macropulses and high pulse repetition rates is presented.

43 PARTICLE ACCELERATORS↗

Optimal control system design of an acid gas removal unit for an IGCC power plants with CO2 capture

Future IGCC plants with CO{sub 2} capture should be operated optimally in the face of disturbances without violating operational and environmental constraints. To achieve this goal, a systematic approach is taken in this work to design the control system of a selective, dual-stage Selexol-based acid gas removal (AGR) unit for a commercial-scale integrated gasification combined cycle (IGCC) power plant with pre-combustion CO{sub 2} capture. The control system design is performed in two stages with the objective of minimizing the auxiliary power while satisfying operational and environmental constraints in the presence of measured and unmeasured disturbances. In the first stage of the control system design, a top-down analysis is used to analyze degrees of freedom, define an operational objective, identify important disturbances and operational/environmental constraints, and select the control variables. With the degrees of freedom, the process is optimized with relation to the operational objective at nominal operation as well as under the disturbances identified. Operational and environmental constraints active at all operations are chosen as control variables. From the results of the optimization studies, self-optimizing control variables are identified for further examination. Several methods are explored in this work for the selection of these self-optimizing control variables. Modifications made to the existing methods will be discussed in this presentation. Due to the very large number of candidate sets available for control variables and due to the complexity of the underlying optimization problem, solution of this problem is computationally expensive. For reducing the computation time, parallel computing is performed using the Distributed Computing Server (DCS®) and the Parallel Computing® toolbox from Mathworks®. The second stage is a bottom-up design of the control layers used for the operation of the process. First, the regulatory control layer is designed followed by the supervisory control layer. Finally, an optimization layer is designed. In this paper, the proposed two-stage control system design approach is applied to the AGR unit for an IGCC power plant with CO{sub 2} capture. Aspen Plus Dynamics® is used to develop the dynamic AGR process model while MATLAB is used to perform the control system design and for implementation of model predictive control (MPC).

97 MATHEMATICS AND COMPUTING↗

Sensor placement algorithm development to maximize the efficiency of acid gas removal unit for integrated gasifiction combined sycle (IGCC) power plant with CO2 capture

Future integrated gasification combined cycle (IGCC) power plants with CO{sub 2} capture will face stricter operational and environmental constraints. Accurate values of relevant states/outputs/disturbances are needed to satisfy these constraints and to maximize the operational efficiency. Unfortunately, a number of these process variables cannot be measured while a number of them can be measured, but have low precision, reliability, or signal-to-noise ratio. In this work, a sensor placement (SP) algorithm is developed for optimal selection of sensor location, number, and type that can maximize the plant efficiency and result in a desired precision of the relevant measured/unmeasured states. In this work, an SP algorithm is developed for an selective, dual-stage Selexol-based acid gas removal (AGR) unit for an IGCC plant with pre-combustion CO{sub 2} capture. A comprehensive nonlinear dynamic model of the AGR unit is developed in Aspen Plus Dynamics® (APD) and used to generate a linear state-space model that is used in the SP algorithm. The SP algorithm is developed with the assumption that an optimal Kalman filter will be implemented in the plant for state and disturbance estimation. The algorithm is developed assuming steady-state Kalman filtering and steady-state operation of the plant. The control system is considered to operate based on the estimated states and thereby, captures the effects of the SP algorithm on the overall plant efficiency. The optimization problem is solved by Genetic Algorithm (GA) considering both linear and nonlinear equality and inequality constraints. Due to the very large number of candidate sets available for sensor placement and because of the long time that it takes to solve the constrained optimization problem that includes more than 1000 states, solution of this problem is computationally expensive. For reducing the computation time, parallel computing is performed using the Distributed Computing Server (DCS®) and the Parallel Computing® toolbox from Mathworks®. In this presentation, we will share our experience in setting up parallel computing using GA in the MATLAB® environment and present the overall approach for achieving higher computational efficiency in this framework.

97 MATHEMATICS AND COMPUTING↗

Sensor placement algorithm development to maximize the efficiency of acid gas removal unit for integrated gasification combined cycle (IGCC) power plant with CO{sub 2} capture

Future integrated gasification combined cycle (IGCC) power plants with CO{sub 2} capture will face stricter operational and environmental constraints. Accurate values of relevant states/outputs/disturbances are needed to satisfy these constraints and to maximize the operational efficiency. Unfortunately, a number of these process variables cannot be measured while a number of them can be measured, but have low precision, reliability, or signal-to-noise ratio. In this work, a sensor placement (SP) algorithm is developed for optimal selection of sensor location, number, and type that can maximize the plant efficiency and result in a desired precision of the relevant measured/unmeasured states. In this work, an SP algorithm is developed for an selective, dual-stage Selexol-based acid gas removal (AGR) unit for an IGCC plant with pre-combustion CO{sub 2} capture. A comprehensive nonlinear dynamic model of the AGR unit is developed in Aspen Plus Dynamics® (APD) and used to generate a linear state-space model that is used in the SP algorithm. The SP algorithm is developed with the assumption that an optimal Kalman filter will be implemented in the plant for state and disturbance estimation. The algorithm is developed assuming steady-state Kalman filtering and steady-state operation of the plant. The control system is considered to operate based on the estimated states and thereby, captures the effects of the SP algorithm on the overall plant efficiency. The optimization problem is solved by Genetic Algorithm (GA) considering both linear and nonlinear equality and inequality constraints. Due to the very large number of candidate sets available for sensor placement and because of the long time that it takes to solve the constrained optimization problem that includes more than 1000 states, solution of this problem is computationally expensive. For reducing the computation time, parallel computing is performed using the Distributed Computing Server (DCS®) and the Parallel Computing® toolbox from Mathworks®. In this presentation, we will share our experience in setting up parallel computing using GA in the MATLAB® environment and present the overall approach for achieving higher computational efficiency in this framework.

20 FOSSIL-FUELED POWER PLANTS↗

Method and system for capturing carbon dioxide and/or sulfur dioxide from gas stream

The present invention provides a system for capturing CO.sub.2 and/or SO.sub.2, comprising: (a) a CO.sub.2 and/or SO.sub.2 absorber comprising an amine and/or amino acid salt capable of absorbing the CO.sub.2 and/or SO.sub.2 to produce a CO.sub.2- and/or SO.sub.2-containing solution; (b) an amine regenerator to regenerate the amine and/or amino acid salt; and, when the system captures CO.sub.2, (c) an alkali metal carbonate regenerator comprising an ammonium catalyst capable catalyzing the aqueous alkali metal bicarbonate into the alkali metal carbonate and CO.sub.2 gas. The present invention also provides for a system for capturing SO.sub.2, comprising: (a) a SO.sub.2 absorber comprising aqueous alkali metal carbonate, wherein the alkali metal carbonate is capable of absorbing the SO.sub.2 to produce an alkali metal sulfite/sulfate precipitate and CO.sub.2.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Risk-Based Comparison of Carbon Capture Technologies

In this paper, we describe an integrated probabilistic risk assessment methodological framework and a decision-support tool suite for implementing systematic comparisons of competing carbon capture technologies. Culminating from a collaborative effort among national laboratories under the Carbon Capture Simulation Initiative (CCSI), the risk assessment framework and the decision-support tool suite encapsulate three interconnected probabilistic modeling and simulation components. The technology readiness level (TRL) assessment component identifies specific scientific and engineering targets required by each readiness level and applies probabilistic estimation techniques to calculate the likelihood of graded as well as nonlinear advancement in technology maturity. The technical risk assessment component focuses on identifying and quantifying risk contributors, especially stochastic distributions for significant risk contributors, performing scenario-based risk analysis, and integrating with carbon capture process model simulations and optimization. The financial risk component estimates the long-term return on investment based on energy retail pricing, production cost, operating and power replacement cost, plan construction and retrofit expenses, and potential tax relief, expressed probabilistically as the net present value distributions over various forecast horizons.

Engel, David W.↗

A Sub-grid Model for an Array of Immersed Cylinders in Coarse-grid Multiphase Flow Simulations of a Carbon Capture Device

A post-combustion carbon-capture system utilizing a bubbling fluidized bed of sorbent particles is currently being developed as a part of the Carbon Capture and Simulation Initiative (CCSI) efforts. Adsorption of carbon dioxide (CO2) by these amine based sorbent particles is exothermic and arrays of immersed cylindrical heat transfer tubes are often utilized to maintain the lower temperatures favorable for CO2 capture. In multiphase computational fluid dynamics (CFD) simulations of the full-scale devices, which can be up to 10 m in size, approximately 103 cells are required in each dimension to accurately resolve the cylindrical tubes, which are only a few centimeters in diameter. Since the tubes cannot be resolved explicitly in CFD simulations, alternate methods to account for the influence of these immersed objects need to be developed.

Sarkar, Avik↗

Pilot-Scale Silicone Process for Low-Cost Carbon Dioxide Capture

GE Global Research is developing technology to remove carbon dioxide (CO 2) from the flue gas of coal-fired powerplants. A mixture of 3-aminopropyl end-capped polydimethylsiloxane (GAP-1m) and triethylene glycol (TEG) is the preferred CO2-capture solvent. GE Global Research was contracted by the Department of Energy to test a pilot-scale continuous CO2 absorption/desorption system using a GAP-1m/TEG mixture as the solvent. As part of that effort, an Environmental, Health, and Safety (EH&S) assessment for a CO2-capture system for a 550 MW coal-fired powerplant was conducted. Five components of the solvent, CAS#2469-55-8 (GAP-0), CAS#106214-84-0 (GAP-1-4), TEG, and methanol and xylene (minor contaminants from the aminosilicone) are included in this assessment. One by-product, GAP- 1m/SOX salt, and dodecylbenzenesulfonicacid (DDBSA) were also identified foranalysis. An EH&S assessment was also completed for the manufacturing process for the GAP-1m solvent. The chemicals associated with the manufacturing process include methanol, xylene, allyl chloride, potassium cyanate, sodium hydroxide (NaOH), tetramethyldisiloxane (TMDSO), tetramethyl ammonium hydroxide, Karstedt catalyst, octamethylcyclotetrasiloxane (D4), Aliquat 336, methyl carbamate, potassium chloride, trimethylamine, and (3-aminopropyl) dimethyl silanol. The toxicological effects of each component of both the CO2 capture system and the manufacturing process were defined, and control mechanisms necessary to comply with U.S. EH&S regulations are summarized. Engineering and control systems, including environmental abatement, are described for minimizing exposure and release of the chemical components. Proper handling and storage recommendations are made for each chemical to minimize risk to workers and the surrounding community.

01 COAL, LIGNITE, AND PEAT↗

Rebuild of Capture Cavity 1 at Fermilab

The front end of the proposed Advanced Superconducting Test Accelerator at Fermilab employs two single cavity cryomodules, known as 'Capture Cavity 1' and 'Capture Cavity 2', for the first stage of acceleration. Capture Cavity 1 was previously used as the accelerating structure for the A0 Photoinjector to a peak energy of ~14 MeV. In its new location a gradient of ~25 MV/m is required. This has necessitated a major rebuild of the cryomodule including replacement of the cavity with a higher gradient one. Retrofitting the cavity and making upgrades to the module required significant redesign. The design choices and their rationale, summary of the rebuild, and early test results are presented.

43 PARTICLE ACCELERATORS↗

SUBTASK 2.3 – SUPPORT OF DOE CARBON CAPTURE SYSTEMS DEVELOPMENT AND MODELING

The ultimate goal of this project is to reduce uncertainty in the deployment of carbon capture and storage (CCS) technologies by overcoming key challenges through a combination of experimentation and modeling studies. The studies focused on key areas of concern for CCS systems and worked to increase overall confidence in the technology. To achieve project goals, the Energy & Environmental Research Center (EERC) identified the following objectives: Determine the potential impacts of coal combustion-derived aerosols on solvent emissions, solvent degradation, and fouling of postcombustion CO2 capture systems. Identify methods to control the formation of aerosols. Evaluate, quantify, and document the regional impacts that could result from implementation of CO2 capture technologies and enhanced oil recovery. Support U.S. Department of Energy (DOE) modeling efforts by providing key information to help reduce the uncertainty of future CCS projects and increase investor and public confidence in the technologies. Four activities were executed to support this effort, and the detailed results of these activities are presented herein. This project was cofunded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Industrial Commission, Mitsubishi Heavy Industries America, Minnkota Power Cooperative, ALLETE, and the Lignite Energy Council.

01 COAL, LIGNITE, AND PEAT↗

Subtask 2.5 – Syngas Testing of NETL's Advanced Precombustion CO2 Capture Solvent

U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) on-site researchers have been examining and developing a novel solvent for precombustion capture that has the potential for improved performance and lower costs compared to Selexol™ and Rectisol®. In Subtask 2.5, the Energy & Environmental Research Center (EERC) conducted actual comparison tests on actual coal-derived syngas of a PEGDME (polyethylene glycol dimethyl ether) Selexol-type solvent and three other solvents provided by NETL. One was a new hybrid PEG–PDMS (poly[dimethylsiloxane]) solvent engineered by NETL. In addition, two commercially available chemicals that are projected to have good CO2 capture abilities were also selected for testing on actual coal-derived syngas. These tests were conducted in the EERC high-pressure fluid-bed gasifier (HPFBG) system utilizing an existing gas-sweetening absorption system (GSAS) to test the solvents. The four solvents tested were Solvent 1 – AGR II from Coastal Chemical Co., LLC, NETL Solvent 2 – XG-3229 Bis(methoxytriethyleneoxypropyl)hexamethyltrisiloxane, as manufactured by Gelast, Inc.; Solvent 3 – CASSH-1 (diethyl sebacate), procured from Sigma Aldrich; and Solvent 4 – TBP (tributyl phosphate), purchased from ThermoFisher Scientific. The solvents were all tested at a consistent syngas flow and composition at approximately 50 bar to make direct comparisons easier; two solvent flow rates which would bracket 90% CO2 capture; and, temperatures of 10°, 25°, 40°, and 55°C to determine the effects of temperature on CO2 uptake and CO2 to H2 selectivity. Figure E-1 shows the results for CO2 uptake and selectivity for the various solvents. These data show that the CO2 uptake for the Selexol-type solvent for the PEG-PDMS-3 and CASHH-1 solvents at higher operating temperatures around 40°C was better than the Selexol-type solvent was able to achieve at the lower operating temperature of 10°C. Selectivity of CO2 over H2 was at least as good as Selexol for the PEG-PDMS-3 solvent and even better than Selexol for the CASSH-1 solvent. The TBP solvent also displayed good CO2 uptake; however, CO2/H2 selectivity was worse than for the Selexol-type solvent. Operation of precombustion CO2 solvents at temperatures above ambient can provide a 2% process efficiency improvement along with a significant capital cost reduction since refrigeration and solvent dehydration equipment is not required. The excellent results from these tests warrant further longer-duration testing with one or both superior NETL-provided solvents to determine if longer-term exposure to any coal-derived syngas trace species may have an adverse impact on solvent performance. This project was funded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233.

01 COAL, LIGNITE, AND PEAT↗

A Viable Path Forward to Carbon Capture and Storage in Wyoming, USA

The State of Wyoming, USA, benefits from favorable geologic, regulatory, and infrastructure attributes that promote efficient and sustainable carbon capture and storage (CCS). Two research sites in Wyoming exhibit high potential for the underground geologic storage of greater than 50 million metric tons of carbon dioxide (CO 2 ) over 25 years. Funded by the U.S. Department of Energy’s (DOE) Carbon Storage Assurance and Facility Enterprise (DOE CarbonSAFE) Phase I prefeasibility initiative, studies of both sites indicate promising capture, transport, utilization, and storage characteristics. The Dry Fork site is located near Gillette, in northeast Wyoming. Four storage reservoir/seal pairs have been identified at the Dry Fork site that provide excellent prospects for stacked storage of CO 2 . All four reservoirs lie at sufficient depths to maintain supercritical CO 2 and all four seals exhibit favorable characteristics for stratigraphic confinement. The reservoir with the highest expected significance is the Pennsylvanian/Permian Minnelusa Formation, which consists of near-shore dunes and shoreline sands, as well as shale and carbonate layers. The Minnelusa resides at a depth of ~2,900 m below the land surface and is ~45 m thick in the study area. Average porosity for samples from core within 10 km of the study area is 9%, with permeability values as high as 169 mD (n=6). The Permian Opeche Formation seals the Minnelusa and consists of redbed shales with minor fine-grained siltstones and evaporite deposits. Entry pressures as high as ~4700 psia were measured by mercury injection capillary pressure (MICP) analysis on core samples from the Opeche. A CarbonSAFE Phase II feasibility proposal at the Dry Fork site has recently been selected by DOE for negotiation leading to award. The second proposed site is located at the Rock Springs Uplift (RSU) in southwest Wyoming. Four reservoir/seal pairs have been studied at the RSU, all of which present promising geologic attributes for the stacked storage of CO 2 . The two deepest reservoirs (Mississippian Madison Limestone and Pennsylvanian/Permian Weber Formation) and their seals were studied previously under the auspices of the Wyoming Carbon Underground Storage Project (WY-CUSP), which was funded by DOE and the State of Wyoming. For the more recent CarbonSAFE initiative, two shallower reservoir/seal pairs were studied in detail. The highest priority of these reservoirs is the Triassic/Jurassic Nugget Formation, which consists of eolian sands and minor fluvial and interdune deposits. The Nugget lies at a depth of ~2,800 m and is ~140 m thick in the study area. Average measured porosity for samples from core within 40 km of the study site is 9%, with permeability values as high as 91 mD (n=10). The Nugget is sealed by the overlying Jurassic Gypsum Spring and Morrison Formations, as well as a thick (~1,700 m) regional Upper Cretaceous seal that includes shales from multiple geologic units. Entry pressures as high as 1120 psia were measured by MICP for shales within this regional confining unit. Overall, the State of Wyoming provides an advantageous climate to develop sustainable integrated CCS projects based on the following considerations: (1) well-characterized and favorable geology; (2) some of the largest deposits of economically recoverable coal in the USA; (3) an existing CO 2 -enhanced oil recovery industry, including CO 2 pipeline infrastructure; (4) supportive commercial enterprises, including utilities and the oil and gas industry; (5) supportive policymakers; (6) a favorable legal and regulatory environment; (7) proximity to carbon-constrained markets such as the State of California; (8) large CO 2 emission sources, including coal-fired power plants; and (9) backing for carbon capture, storage, and management related research and development, specifically implementation of the Integrated Test Center at Dry Fork Station, which is hosting the coal-track of the NRG/COSIA Carbon XPrize® competition.

Phillips, Erin↗

Polyamine phosphorus dendrimer materials for carbon dioxide capture

The present disclosure provides novel solid sorbents synthesized by the reaction of polyamines with polyaldehyde phosphorous dendrimer (P-dendrimer) compounds. The sorbents are highly stable and exhibit rapid reaction kinetics with carbon dioxide, making the sorbents applicable for carbon capture, and can be easily regenerated for further use. The material is stable to aqueous and organic media, as well as strong acid and bases. The sorbent maintains full capacity over extended use. The material can be used for CO2 capture from pure CO2 streams, mixed gas streams, simulated flue gas, and ambient air. Additionally, the material can be adhered to surfaces for reversible CO2 capture applications outside of bulk particle-based processes.

Thompson, III, Samuel John↗

Recent Improvements in the Beam Capture at Fermilab Booster for High Intensity Operation

The Fermilab Booster uses multi-turn beam injection with all its cavities phased such that beam sees a net zero RF voltage even when each station is at the same maxi-mum voltage. During beam capture the RF voltage is increased slowly by using its paraphase system. At the end of the capture the feedback is turned on for beam acceleration. It is vital for present operations as well as during the PIP-II era that both the HLRF and LLRF systems provide the proper intended phase and RF voltage to preserve the longitudinal emittance from injection to extraction. In this paper, we describe the original architecture of the cavity phase distribution, our recent beam-based RF phase measurements, observed significant deviation in the relative phases between cavities and correction effort. Results from the improved capture for high intensity beam are also presented.

43 PARTICLE ACCELERATORS↗

Additional Analysis of Carbon Capture at Industrial Facilities

This poster provides summary cost details for a technoeconomic analysis of CO2 capture from flue gas generated by cement plants, conducted by U.S. Department of Energy National Energy Technology Laboratory and presented at the 2022 Carbon Management Project Review Meeting held in Pittsburgh, PA (August 15-19, 2022). A range of modern cement plant configurations was considered, along with different fuel types (coal, coke, and natural gas) and two levels of CO2 capture (95% and 99%). The sensitivity of capture cost to a range of modeling assumptions (such as fuel price, financing assumptions, utilization rate, and plant size) was also conducted, to show possible cost ranges that could be expected for decarbonization of typical cement plants in the U.S.

Hughes, Sydney↗

User Guide for the Public Industrial CO2 Capture Retrofit Database Models

OBSOLETE CCRD – SUPERSEDED<p>The National Energy Technology Laboratory (NETL) user manual accompanies the carbon capture retrofit database (CCRD) model that allows users to evaluate the cost of carbon capture on industrial sources (ammonia, cement, ethanol, hydrogen, and natural gas processing). The model was created by the National Energy Technology Laboratory (NETL) based on the technical report titled &quot;Cost of Capturing CO2 from Industrial Sources&quot; (NETL/DOE-2022/3319). Revised 12/21/22.</p>

Hughes, Sydney↗