Search NASA⌕ Search

SEARCH · Search NASA

Results for “Data Plotting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Estimation of the Tritium Isotope Effect inthe SAS Compressor Bed 1 Material (LANA10)

A recent report presented a method to estimate the SAS Compressor Bed 1 (SAS CB1) loading level, in Q/M units, based on measured equilibrium pressure and temperature where the material was clearly loaded into the β-phase. This method requires the use of the equilibrium desorption isotherm plateau pressure, but no data exists to specify that value at this time. This report details a previously unreported investigation into tritium isotope effects on plateau pressure of a closely related material, herein called LANA05, conducted in the 1989-to-1993 time frame by then-SRL (Savannah River Laboratory) researchers. Data from that investigation is used to estimate the tritium isotope effect on plateau pressure in the SAS CB1 virgin LANA10 material by constructing a tritium van’t Hoff plot for LANA10 that mimics the isotope behavior in LANA05.

36 MATERIALS SCIENCE↗

Optimizing cosmogenic burial isochrons using muon-inclusive simple burial dating

Isochron burial dating with cosmogenic nuclides presents new opportunities for determining the deposition age of Plio-Pleistocene gravels. The method uses paired measurements of 26 Al and 10 Be from individual clasts and is able to generate ages even if burial histories are complex and poorly constrained. Critical to the isochron method is the assumption that gravel is deposited with a predictable 26 Al/ 10 Be ratio, based on near-surface production rates, that then decreases due to radioactive decay after burial. If all clasts are collected from the same depth in a deposit, they share the same history of post-burial production and decay. Because decay constants are known, a line regressed through a bivariate plot of 26 Al and 10 Be concentrations represents an isochron, the slope of which is related to burial duration. The method is ideal when samples are numerous (≥ 5 data points) and yield a spread of concentrations such that linear regression can resolve a meaningful slope, but logistics, costs, and site geology can preclude such ideal datasets. Additionally, it can be difficult to identify and reject samples that may have been deposited with nuclide ratios resulting from prior burial that have the potential to contaminate isochron age estimates. Here we present a methodology for checking the integrity of small isochron datasets (≤4 samples) by co-applying a muon-inclusive simple burial dating algorithm that scales muogenic production with shielding mass (cover density * depth). This analysis uses the same 26 Al and 10 Be concentrations as the isochron method, but incorporates assumptions based on site geology to independently validate and inform isochron results. We use two examples to demonstrate how these burial calculations can increase confidence in isochron results, show when the isochron method is inappropriately applied, and provide criteria for rejection of data points in isochrons.

58 GEOSCIENCES↗

Integrating Characteristic Arctic Vegetation in a Land Surface Model Improves Representation of Carbon Dynamics Across a Tundra Landscape

Arctic warming is altering vegetation and carbon dynamics with global implications, yet Earth System Model (ESM) predictions in the Arctic remain highly uncertain, in part due to historically limited data for model parameterization and validation. As such, ESMs typically represent Arctic ecosystems in an oversimplified manner. Recently, nine plant functional types (PFTs) designed to realistically represent tundra vegetation were integrated into the Energy Exascale Earth System Model (E3SM) Land Model (ELM) and parameterized using plot-scale observations from a single site. Additional evaluation was needed to determine their transferability across the Arctic. Here, in this study, we evaluated whether refined representation of tundra vegetation improved model accuracy by conducting spatially explicit 100 × 100 m resolution ELM simulations on Alaska's Seward Peninsula. Simulations with the default two-PFT configuration and with the nine Arctic-specific PFTs were benchmarked against observations of net ecosystem exchange, gross primary production, and aboveground biomass from multiple data streams including an eddy covariance flux tower, flux chambers, and aircraft and unoccupied aerial system hyperspectral remote sensing. Evaluation revealed that Arctic-specific PFT simulations produced more realistic landscape-level carbon exchanges, and better captured observed heterogeneity in biomass and productivity, explaining 60%–70% of spatial variance (R 2 = 0.6–0.7) compared to just 12%–18% (R 2 = 0.12–0.18) with the default configuration. However, the refined model failed to reproduce observed aboveground biomass for highly productive alder-willow communities, requiring further evaluation of carbon allocation parameterizations for tall shrubs that are increasingly expanding across tundra landscapes. Our results demonstrate that enhanced representation of vegetation heterogeneity boosts predictive understanding of tundra carbon dynamics, facilitating regional to pan-Arctic model and remote-sensing scaling.

Murphy, Bailey A. [Oak Ridge National Laboratory (↗

The Binary Alkali Nitrate and Chloride Phase Diagrams: NaNO{sub 3}-KNO{sub 3}, LiNO{sub 3}-NaNO{sub 3}, LiNO{sub 3}-KNO{sub 3}, and NaCl-KCl

LiNO{sub 3}-NaNO{sub 3}, LiNO{sub 3}-KNO{sub 3,} NaNO{sub 3}-KNO{sub 3}, and NaCl-KCl phase relations were formulated using the regular solution model to obtain desired compositions for their potential application as a heat transfer fluid. The simultaneous nonlinear equations formed were solved numerically using a contour plot technique in Matlab. An algorithm was developed to determine the real roots of the coupled nonlinear equations and subsequent phase diagrams were constructed. The phase diagrams were compared with those predicted using FactSage thermochemical package and literature data from experimental studies. The calculated NaNO{sub 3}-KNO{sub 3} phase diagram shows that this system has a eutectic point at 0.5 mole fraction of KNO{sub 3} with a eutectic temperature of 220.85 °C, while the LiNO{sub 3}-KNO{sub 3} system was found to have a eutectic point at 0.44 mole fraction LiNO{sub 3} at 137 °C. The LiNO{sub 3}-NaNO{sub 3} system shows a eutectic at 0.524 mole fraction LiNO{sub 3} at 192.8 °C, and finally the NaCl-KCl system has a eutectic point at 0.48 mole fraction NaCl at 634 °C. The liquidus and solidus curves obtained fitted close against values obtained from the quasi-chemical model used in FactSage and experimental values from the literature. This study showed that the regular solution model combined with the contour plots approach can sufficiently describe the liquidus–solidus curves of the alkali binary nitrate and chloride systems and could be a useful method for predicting the phase diagrams for higher order alkali nitrates and chlorides.

36 MATERIALS SCIENCE↗

Constitutive Modeling for Hot Working Behavior of SP-700 Titanium Alloy

In this paper, the constitutive modeling and hot deformation behavior of SP-700 titanium alloy was investigated by performing isothermal hot compression tests in the temperature range of 700-950 °C and strain rates of 0.001, 0.1, and 1 s{sup −1}. The flow curves of the alloy indicated that the yield point phenomenon occurs at strain rates of 0.1 and 1 s{sup −1}. The friction, adiabatic heating, and stroke-rate controlling effects were eliminated from the raw data. Then, three types of phenomenological constitutive models, considering the compensation of strain, were used to predict the flow stresses of the alloy. The correlation coefficients (R{sup 2}) of the measured and predicted results for the power-law, hyperbolic-sine law, and dynamic softening models were found to be 0.9790, 0.9883, and 0.9877, respectively. The corresponding average absolute relative errors (AARE) were 6.3, 5.9, and 7.45%, respectively. The flow softening behavior of SP-700 alloy was modeled using the combined hyperbolic-sine law and dynamic softening model approach. The predicted flow stresses were in a good agreement with the experimental data, indicated that the developed models can accurately characterize flow behavior of the alloy. In addition, the strain-rate sensitivity (m) distribution map of the alloy was obtained by plotting the m-value against temperature and strain rate in the form of a contour map. There was the maximum of m-value (0.36) in the temperature ranges of 700-715 and 837-875 °C, and strain rates of 0.001-0.006 s{sup −1}. The microstructure of hot deformed at 700 °C mainly consists of globularized and lamellar α phase, while dynamic globularization was completed at 800 °C. The hot deformation activation energy of the alloy in α/β region (305.5 kJ mol{sup −1}) was higher than that in single-phase β region (165.2 kJ mol{sup −1}) due to the globularization of lamellar α.

36 MATERIALS SCIENCE↗

Mitigation of rapid capacity decay in silicon-LiNi 0.6 Mn 0.2 Co 0.2 O 2 full batteries

Silicon (Si)-based materials have been considered as the most promising anode materials for high-energy-density lithium-ion batteries because of their higher storage capacity and similar operating voltage, as compared to the commercial graphite (Gr) anode. But the use of Si anodes including silicon-graphite (Si-Gr) blended anodes often leads to rapid capacity decay in Si-Gr/LiNixMnyCo z O 2 (x+y+z=1) full cells, which has been attributed to surface instability of the Si component. In addition to stabilizing the surface, this work investigates the potential of the Si-Gr blended anodes in a full-cell configuration and its impact on the capacity contribution from active components. Using dQ/dV plots of the full cells, a powerful but simple-to-implement differential potential approach is developed to decouple the capacity contribution and degradation from the graphite and silicon components. Data collected from three-electrode cells confirm the results from the differential potential approach, which suggests a voltage slippage to a higher voltage at the blended anode side. Additionally, the voltage slippage causes a reduced utilization of the Gr component and exacerbates side reactions between the Si-Gr anode and carbonate electrolytes. Furthermore, based on these failure mechanisms, we adopted a mitigation strategy to tune the open circuit voltage of the prelithiated anode while stabilizing the surface. As a result, the full cells with the modified Si-Gr anodes (mass loading, 2.5 mAh/cm 2 ) offer a highly reversible full-cell energy density of 390 Wh/kg (based on the mass of both anode and cathode materials in a full cell) with a cycling CE of 99.9% over 200 cycles.

25 ENERGY STORAGE↗

Experimental investigation of the effect of indium content on the CuIn{sub 5}S{sub 8} electrodes using electrochemical impedance spectroscopy

This paper reports on the use of electrochemical impedance spectroscopy to investigate the electrochemical behavior of spinel CuIn{sub 5}S{sub 8}/electrolyte interface. The CuIn{sub 5}S{sub 8} spinel films have been potentiostatically deposited onto indium tin oxide (ITO)-coated glass substrate. CuCl{sub 2} and InCl{sub 3} mixed solutions with different [Cu]/[In] ratios were used as cation precursor and Na{sub 2}S{sub 2}O{sub 3} as the anion precursor in acidic solution and at room temperature. The effect of the [Cu]/[In] ratio in the precursor solution on the structural, chemical stoichiometry, and morphological properties of prepared samples, as well as the electrochemical behavior of the CuIn{sub 5}S{sub 8}/electrolyte interface was investigated. The electrochemical impedance spectroscopy data have been modeled using an equivalent circuit approach. Several parameters such as, flat-band potential and free carrier concentration were determined by the change in the Mott–Schottky plots.

36 MATERIALS SCIENCE↗

AmeriFlux FLUXNET-1F AR-Bal Balcarce BA

This is the AmeriFlux Management Project (AMP) created FLUXNET-1F version of the carbon flux data for the site AR-Bal Balcarce BA. This is the FLUXNET version of the carbon flux data for the site AR-Bal Balcarce BA produced by applying the standard ONEFlux (1F) software. Site Description - The study was carried out in a 19-ha rainfed soybean plot at the Unidad Integrada Balcarce, located southeast of Buenos Aires, Argentina. The site is located in an environment of gentle hills at 130 m.a.s.l. Its soil was classified as a typical Argiudoll, with a loamy clayey texture up to 0.30 m and between 0.80 to 1.10 m depth, and a clayey texture between 0.30 and 0.80 m depth. The slope was 1:50 and oriented NE to SW. A caliche layer was found at 1 to 1.2 m depth thus the water table was considered beneath that level. The soybean variety used was DM 3810, Maturity Group III with an indeterminate growing habit. It was sown on November 21, 2012, and emerged on December 1. The crop archive had a maximum height of 0.75 m.

Gassmann, Maria Isabel [Universidad de Buenos Aire↗

Interannual Variations in the Rate of Carbon Storage by a Mid-Latitude Forest (Final Technical Report)

The time series of Net Ecosystem Exchange (NEE) of carbon by an entire forest ecosystem on time scales from hourly to decadal was measured by eddy-covariance supplemented with plot-level measurements of biomass and tree demography. The results demonstrate the response of forest carbon fluxes and long-term budgets to climatic factors and to successional change. The data from this project have been extensively used worldwide by the carbon cycle science community in support of model development and validation of remote sensing observations.

54 ENVIRONMENTAL SCIENCES↗

Analysis of BSRT Profiles in the LHC at Injection

The beam synchrotron radiation telescope (BSRT) at the LHC allows to take profiles of the transverse beam distribution, which can provide useful additional insight in the evolution of the transverse beam distribution. A python class has been developed, which allows to read in the BSRT profiles, usually stored in binary format, run different analysis tools and generate plots of the statistical parameters and profiles as well as videos of the the profiles. The detailed analysis will be described in this note. The analysis is based on the data obtained at injection energy (450 GeV) during MD1217 and MD1415 which will be also used as illustrative example. A similar approach is also taken with a MATLAB based analysis described in.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Measured Thermal and Fast Neutron Fluence Rates ATR Cycles 167A

This report contains the thermal (2200 m/s) and fast (E>1MeV) neutron fluence rate data for ATR Cycle 167A which were measured by the Radiation Measurements Laboratory (RML) as requested by the Power Reactor Programs (ATR Experiments) Radiation Measurements Work Order. The report contains fluence rate values corresponding to the particular elevations (relative to the 80-ft. core elevation) where the measurements were taken. The data in this report consists of (1) a table of the ATR power history and distribution, (2) a hard copy listing of all thermal and fast neutron fluence rates, (3) plots of both the thermal and fast neutron fluence rates.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Measured Thermal and Fast Neutron Fluence Rates ATR Cycles 171A AFC (Rev. 1)

This report contains the thermal (2200 m/s) and fast (E>1MeV) neutron fluence rate data for ATR Cycle 171A AFC which were measured by the Radiation Measurements Laboratory (RML) as requested by the Power Reactor Programs (ATR Experiments) Radiation Measurements Work Order. This report contains fluence rate values corresponding to the particular elevations (relative to the 80-ft. core elevation) where the measurements were taken. The data in this report consists of (1) a table of the ATR power history and distribution, (2) a listing of the calculated thermal and fast neutron fluence rates, and (3) plots of calculated both the thermal and fast neutron fluence rates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Measured Thermal and Fast Neutron Fluence Rates ATR Cycles 171A ATF (Rev. 1)

This report contains the thermal (2200 m/s) and fast (E>1MeV) neutron fluence rate data for ATR Cycle 171A ATF which were measured by the Radiation Measurements Laboratory (RML) as requested by the Power Reactor Programs (ATR Experiments) Radiation Measurements Work Order. This report contains fluence rate values corresponding to the particular elevations (relative to the 80-ft. core elevation) where the measurements were taken. The data in this report consists of (1) a table of the ATR power history and distribution, (2) a listing of the calculated thermal and fast neutron fluence rates, and (3) plots of calculated both the thermal and fast neutron fluence rates. The fluence rates reported are for the average power levels given in the table of power history and distribution. During the irradiation of Cycle 152A, the RML performed additional flux measurements to assess core reconfiguration issues. Measurements using cadmium covered as well as bare neutron monitors in the Southwest, Southeast, and H positions of the Center lobe were performed to determine the division in neutron energy between epithermal and thermal neutrons. This is defined as the resonance correction defined in this report. It is used to quantify both thermal and fast neutron flux. For more information please refer to letter, “RADIATION MEASUREMENTS LABORATORY MEASUREMENTS OF IN CORE ATR PHYSICS TESTING DURING CYCLE 152A” dated January 24, 2013, to Casey Stengel from C. C. Jensen. The measured values documented in RML Procedure, “ACMM-3600, Flux Monitoring,” will be used indefinitely until further measurements supersede the current values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Measured Thermal and Fast Neutron Fluence Rates ATR Cycles 171A IR TMIST 3B

This report contains the thermal (2200 m/s) and fast (E>1MeV) neutron fluence rate data for ATR Cycle 171A which were measured by the Radiation Measurements Laboratory (RML) as requested by the Power Reactor Programs (ATR Experiments) Radiation Measurements Work Order. This report contains fluence rate values corresponding to the particular elevations (relative to the 80-ft. core elevation) where the measurements were taken. The data in this report consists of (1) a table of the ATR power history and distribution, (2) a listing of the calculated thermal and fast neutron fluence rates, and (3) plots of calculated both the thermal and fast neutron fluence rates. The fluence rates reported are for the average power levels given in the table of power history and distribution. During the irradiation of Cycle 152A, the RML performed additional flux measurements to assess core reconfiguration issues. Measurements using cadmium covered as well as bare neutron monitors in the Southwest, Southeast, and H positions of the Center lobe were performed to determine the division in neutron energy between epithermal and thermal neutrons. This is defined as the resonance correction defined in this report. It is used to quantify both thermal and fast neutron flux. For more information please refer to letter, “RADIATION MEASUREMENTS LABORATORY MEASUREMENTS OF IN CORE ATR PHYSICS TESTING DURING CYCLE 152A” dated January 24, 2013, to Casey Stengel from C. C. Jensen. The measured values documented in RML Procedure, “ACMM-3600, Flux Monitoring,” will be used indefinitely until further measurements supersede the current values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Measured Thermal And Fast Neutron Fluence Rates ATR Cycle 166B

This report contains the thermal (2200 m/s) and fast (E>1MeV) neutron fluence rate data for ATR Cycle 166B which were measured by the Radiation Measurements Laboratory (RML) as requested by the Power Reactor Programs (ATR Experiments) Radiation Measurements Work Order. This report contains fluence rate values corresponding to the particular elevations (relative to the 80-ft. core elevation) where the measurements were taken. The data in this report consists of (1) a table of the ATR power history and distribution, (2) a hard copy listing of all thermal and fast neutron fluence rates, (3) plots of both the thermal and fast neutron fluence rates, and (4) an optical record (compact disk) containing a listing of the thermal and the fast neutron fluence rates, their assigned elevations and proper header identification of all monitor positions contained herein. The fluence rates reported are for the average power levels given in the table of power history and distribution. No neutron monitors were located in the N-2 position during this cycle.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Resistance, Resilience, and Recovery of Dryland Soil Bacterial Communities Across Multiple Disturbances

Dryland ecosystems are sensitive to perturbations and generally slow to recover post disturbance. The microorganisms residing in dryland soils are especially important as they contribute to soil structure and nutrient cycling. Disturbance can have particularly strong effects on dryland soil structure and function, yet the natural resistance and recovery of the microbial components of dryland soils has not been well documented. In this study, the recovery of surface soil bacterial communities from multiple physical and environmental disturbances is assessed. Samples were collected from three field sites in the vicinity of Moab, UT, United States, 6 to 7 years after physical and climate disturbance manipulations had been terminated, allowing for the assessment of community recovery. Additionally, samples were collected in a transect that included three habitat patches: the canopy zone soils under the dominant shrubs, the interspace soils that are colonized by biological soil crusts, and edge soils at the plot borders. Field site and habitat patch were significant factors structuring the bacterial communities, illustrating that sites and habitats harbored unique soil microbiomes. Across the different sites and disturbance treatments, there was evidence of significant bacterial community recovery, as bacterial biomass and diversity were not significantly different than control plots. There was, however, a small number of 16S rRNA gene amplicon sequence variants that distinguished particular treatments, suggesting that legacy effects of the disturbances still remained. Taken together, these data suggest that dryland bacterial communities may possess a previously unappreciated potential to recover within years of the original disturbance.

59 BASIC BIOLOGICAL SCIENCES↗

Tiamat

Tiamat is the driver program for coupling three application codes together to simulate a nuclear reactor core. This code is used to study pellet clad interaction failures in commercial nuclear light water It generates stress plots and temperature profiles for fuel rods in the reactor core. The driver program initializes the underlying applications, initiates the overall solve process, generates consistent input files and manages the data transfers between the applications. It contains the top level driver code, the data transfer code, input file parsing and corresponding unit tests. Tiamat was developed under the CASL Energy Innovation Hub. The Tiamat code DOES NOT include any source code for the actual coupled physics application components or solvers. The application codes and solver libraries must be obtained separately from the Tiamat source code. Tiamat will be released open source under a BSD license.

Source record↗

Measured Thermal And Fast Neutron Fluence Rates ATR Cycle 169A

This report contains the thermal (2200 m/s) and fast (E>1MeV) neutron fluence rate data for ATR Cycle 169A which were measured by the Radiation Measurements Laboratory (RML) as requested by the Power Reactor Programs (ATR Experiments) Radiation Measurements Work Order. This report contains fluence rate values corresponding to the particular elevations (relative to the 80-ft. core elevation) where the measurements were taken. The data in this report consists of ( 1) a table of the ATR power history and distribution, (2) a hard copy listing of all thermal and fast neutron fluence rates, (3) plots of both the thermal and fast neutron fluence rates, and (4) an optical record (compact disk) containing a listing of the thermal and the fast neutron fluence rates, their assigned elevations and proper header identification of all monitor positions contained herein. The fluence rates reported are for the average power levels given in the table of power history and distribution. No neutron monitors were located in the N-2 position during this cycle. All "SR" holder monitor wires for this cycle are 55 inches long. This length allows measurements from 24.73 inches above core midplane to 25.25 inches below core midplane. The distance from the end of the wires to the first count position was 4.25 inches for all wires counted from this cycle.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗