SEARCH · Search NASA

Results for “Geared”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

All sources NASA NTRS DOE OSTI

NASA NTRS1975

A study of helicopter interior noise reduction

The interior noise levels of existing helicopters are discussed along with an ongoing experimental program directed towards reducing these levels. Results of several noise and vibration measurements on Langley Research Center's Civil Helicopter Research Aircraft are presented, including measurements taken before and after installation of an acoustically-treated cabin. The predominant noise source in this helicopter is the first stage planetary gear-clash in the main gear box, both before and after installation of the acoustically treated cabin. Noise reductions of up to 20 db in some octave bands may be required in order to obtain interior noise levels comparable to commercial jet transports.

Howlett, J. T.↗

NASA NTRS1976

Concentric-tube differential drive

Remote manipulator consists essentially of gear shafts that are placed concentrically with bevel gears located at each joint. Teleoperator's advantages include light weight accessibility of parts, continuous rotation of joints, possibility of underwater use, and possibility of miniaturization.

Marlow, R. E.↗

NASA NTRS1976

OH-58 helicopter transmission failure analysis

The OH-58 main transmission gearbox was run at varying output torques, speeds, and oil cooling rates. The gearbox was subsequently run to destruction by draining the oil from the gearbox while operating at a speed of 6200 revs per minute and 36,000 inch-pounds output torque. Primary cause of gearbox failure was overheating and melting of the planet bearing aluminum cages. Complete failure of the gearbox occurred in 28 1/2 minutes after the oil pressure dropped to zero. The alternating and maximum stresses in the gearbox top case were approximately 10 percent of the endurance limit for the material. Deflection of the bevel gear at 67000 inch-pounds output torque indicate a marginal stiffness for the bevel gear supporting system.

Townsend, D. P.↗

NASA NTRS1975

Landing pressure loads of the 140A/B space shuttle orbiter (model 43-0) determined in the Rockwell International low speed wind tunnel (OA69), volume 1

Wind tunnel tests of a 0.0405 scale model of the -1404A/B configuration of the Space Shuttle Vehicle Orbiter are presented. Pressure loads data were obtained from the orbiter in the landing configuration in the presence of the ground for structural strength analysis. This was accomplished by locating as many as 30 static pressure bugs at various locations on external model surfaces as each configuration was tested. A complete pressure loads survey was generated for each configuration by combining data from all bug locations, and these loads are described for the fuselage, wing, vertical tail, and landing gear doors. Aerodynamic force data was measured by a six component internal strain gage balance. This data was recorded to correct model angles of attack and sideslip for sting and balance deflections and to determine the aerodynamic effects of landing gear extension. All testing was conducted at a Mach number of 0.165 and a Reynolds number of 1.2 million per foot. Photographs of test configurations are shown.

Soard, T. L.↗

NASA NTRS1975

Design definition study of a life/cruise fan technology V/STOL aircraft. Volume 2, addendum 2: Program risk assessment

The results are presented of a risk assessment study conducted on two technology aircraft. The aircraft system components were reviewed and assessed for risk based on: (1) complexity relative to state-of-the-art, (2) manufacturing and qualification testing, (3) availability and delays, and (4) cost/schedule impact. These assessments were based on five risk nomenclatures: low, minor, moderate, high, and extreme. Each aircraft system was assigned an overall risk rating depending upon its contribution to the capability of the aircraft to achieve the performance goals. The slightly lower Sabreliner performance margin is due to the restricted flight envelope, the fixed landing gear, and internal fuel capacity. The Sabreliner with retractable gear and allowed to fly at its best speed and altitude would reflect performance margins similar to the New Airframe. These significant margins, inherent with the MCAIR three gas generator/three fan propulsion system, are major modifiers to risk assessment of both aircraft. The estimated risk and the associated key system and performance areas are tabulated.

Source record↗

NASA NTRS1976

A flight investigation of piloting techniques and crosswind limitations during visual STOL-type landing operations

A flight research program was undertaken to investigate problems concerned with landing a STOL airplane in crosswind conditions. The program included a study of piloting techniques and crosswind limitations during visual STOL type landing operations. The results indicated that the crosswind was more limiting during the ground roll out than during the airborne phases. The pilots estimated that the crosswind limit for commercial STOL type operations with the test aircraft would be approximately 15 to 20 knots. The pilots thought that the crosswind limits for ground operation might be extended by incorporating wing-lift spoilers, improved nose gear steering, and improved engine response. The pilots agreed that a crosswind landing gear would also be beneficial.

Fisher, B. D.↗

NASA NTRS1976

Dual output variable pitch turbofan actuation system

An improved actuating mechanism was provided for a gas turbine engine incorporating fan blades of the variable pitch variety, the actuator adapted to rotate the individual fan blades within apertures in an associated fan disc. The actuator included means such as a pair of synchronizing ring gears, one on each side of the blade shanks, and adapted to engage pinions disposed thereon. Means were provided to impart rotation to the ring gears in opposite directions to effect rotation of the blade shanks in response to a predetermined input signal. In the event of system failure, a run-away actuator was prevented by an improved braking device which arrests the mechanism.

Griswold, R. H., Jr.↗

NASA NTRS1977

Preliminary design of propulsion system for V/STOL research and technology aircraft

The V/STOL Research and Technology Aircraft (RTA)propulsion system design effort is limited to components of the lift/cruise engines, turboshaft engine modifications, lift fan assembly, and propulsion system performance generation. The uninstalled total net thrust with all engines and fans operating at intermediate power was 37,114 pounds. Uninstalled system total net thrust was 27,102 pounds when one lift/cruise is inoperative. Components have lives above the 500 hours of the RTA duty cycle. The L/C engine used in a fixed nacelle has the cross shaft forward of the reduction gear whereas the cross shaft is aft of the reduction gear in a tilt nacelle L/C engine. The lift/cruise gearbox contains components and technologies from other DDA engines. The rotor has a 62-inch diameter and contains 22 composite blades that have a hub/tip ratio of 0.454. The blade pitch change mechanism contains hydraulic and mechanical redundancy. The lift fan assembly is completely self-contained including oil cooling in 10 exit vanes.

Source record↗

NASA NTRS1977

Airframe noise measurements by acoustic imaging

Studies of the noise produced by flow past wind tunnel models are presented. The central objective of these is to find the specific locations within a flow which are noisy, and to identify the fluid dynamic processes responsible, with the expectation that noise reduction principles will be discovered. The models tested are mostly simple shapes which result in types of flow that are similar to those occurring on, for example, aircraft landing gear and wheel cavities. A model landing gear and a flap were also tested. Turbulence has been intentionally induced as appropriate in order to simulate full-scale effects more closely. The principal technique involves use of a highly directional microphone system which is scanned about the flow field to be analyzed. The data so acquired are presented as a pictorial image of the noise source distribution. An important finding is that the noise production is highly variable within a flow field and that sources can be attributed to various fluid dynamic features of the flow. Flow separation was not noisy, but separation closure usually was.

Kendall, J. M.↗

NASA NTRS1977

Validation of a Flexible Aircraft TakeOff and Landing Analysis /FATOLA/ computer program using flight landing data

A multiple-degree-of-freedom takeoff and landing analysis, Flexible Aircraft TakeOff and Landing Analysis computer program (FATOLA), was used to predict the landing behavior of a rigid-body X-24B reentry research vehicle and of a flexible-body modified-delta-wing supersonic YF-12 research aircraft. The analytical predictions were compared with flight test data for both research vehicles. Predicted time histories of vehicle motion and attitude, landing-gear strut stroke, and axial force transmitted from the landing gear to the airframe during the landing impact and rollout compared well with the actual time histories. Based on the comparisons presented, the versatility and validity of the FATOLA program for predicting landing dynamics of aircraft has been demonstrated.

Carden, H. D.↗

NASA NTRS1977

Airframe noise of the DC-9

Airframe noise measurements are reported for the DC-9-31 aircraft flown at several speeds and with a number of flap, landing gear, and slat extension configurations. The data are corrected for atmospheric attenuation and spherical divergence, and are presented for an overhead position normalized to a 1-meter height. The sound pressure levels are found to vary approximately as the fifth power of flight velocity. Both lift and drag dipoles exist as a significant part of the airframe noise. The data are compared with airframe noise predictions using the drag element and the data analysis methods. Although some of the predictions are very good, further work is needed to refine these methods, particularly for the gear-down and flaps-down configurations.

Bauer, A. B.↗

NASA NTRS1979

Shaft speed control

Simple mechanism controls rotation of heavy-duty shaft by mechanical comparison with rotation of small, precise, stepper motor. Mechanism can be used to limit winding and unwinding speeds of large spools and reels and to control speed of other rotating shafts. Setup incorporates reference shaft geared down from stepper motor and feedback shaft geared up from shaft to be controlled. Feedback and reference shafts are coupled with brake assembly inside stationary cylinder. When work shaft speeds up, brakes are activated automatically to slow it down.

Ford, A. G.↗

NASA NTRS1977

Selectable polarization at X-band

The X-band feeds in the Deep Space Network were upgraded to include selectable polarization in time for the Voyager missions to the outer planets. The modified antenna feed has the following major items added: two circular waveguide rotary joints, drive motor and gear reducer, gear assembly, two microswitches, and a polarization control junction box. The overall length of the feed remains the same because circular waveguide spacing sections were designed into the original feed to readily permit such modifications. There is no significant increase in antenna noise temperature compared to the original feed.

Hartop, R. W.↗

NASA NTRS1978

Wrist joint assembly

A wrist joint assembly is provided for use with a mechanical manipulator arm for finely positioning an end-effector carried by the wrist joint on the terminal end of the manipulator arm. The wrist joint assembly is pivotable about a first axis to produce a yaw motion, a second axis is to produce a pitch motion, and a third axis to produce a roll motion. The wrist joint assembly includes a disk segment affixed to the terminal end of the manipulator arm and a first housing member, a second housing member, and a third housing member. The third housing member and the mechanical end-effector are moved in the yaw, pitch, and roll motion. Drive means are provided for rotating each of the housings about their respective axis which includes a cluster of miniature motors having spur gears carried on the output drive shaft which mesh with a center drive gear affixed on the housing to be rotated.

Kersten, L.↗

NASA NTRS1978

Some alternative dynamic design configurations for large horizontal axis WECS

The present U.S. development effort toward large horizontal axis WECS concentrates on the configuration with two rigid blades with collective pitch variation and a yaw gear drive. Alternative configurations without yaw gear drive were considered where the rotor is either selfcentering or where the yaw angle is controlled by blade cyclic pitch inputs. A preliminary evaluation of the dynamic characteristics for these alternative design configurations is presented.

Hohenemser, K. H.↗

NASA NTRS1978

Helicopter internal noise reduction research and development application to the SA 360 and SA 365 Dauphin

Noise sources inside helicopter cabins are considered with emphasis on the mechanisms of vibration generation inside the main gear box and mechanisms of transmission between source and cabin. The dynamic behavior of the main gear box components is examined in relation to the transfer of vibration energy to the structure. It is indicated that although improvements can be made in noise reduction at the source, a soundproofing treatment isolating the passenger from the noise source is necessary. Soundproofing treatments installed and optimized include: (1) an acoustic screen using the weight effect to isolate the passenger from the noise source; (2) a damping treatment to limit the conversion of the vibratory energy into acoustic energy; and (3) an absorbing treatment achieved either through HELMHOLTZ resonators or through a glass wool blanket to limit the propagation of acoustic waves and the wave reflection effects in the cabin. The application of treatments at the source and the optimization of the sound barriers improved the noise level by about 30 db.

Marze, H. J.↗

NASA NTRS1978

Operational Loopwheel Suspension System for Mars Rover Demonstration Model

The loopwheel (or elastic loop) mobility concept, appears to be uniquely qualified to provide a high degree of mobility at low weight and stowage requirements for the next Mars mission now in the early planning stage. Traction elements compatible with sterilization and Mars surface environmental constraints were designed and are compatible with the rover mass, range and stowage requirements of JPL's point design Mars rover. In order to save cost, the loopwheel suspensions for the demonstration model were made of S-glass/epoxy instead of titanium, alloy specified for flight units. The load carrying fiberglass loop core is covered by a rubber tread on the outside. Reinforced rubber gear belts bonded along the inside edges provide positive engagement and transmission drive torques. A 12 Vdc drive motor with a 167:1 gear head is installed in the payload section of the hull. A chain drive transmits the motor power to the rear sprocket in the demonstration model, whereas future flight units would be directly driven by brushless hub motors within each sprocket and independent four-leg height control.

Trautwein, W.↗

NASA NTRS1979

Compact artificial hand

A relatively simple, compact artificial hand, is described which includes hooks pivotally mounted on first frame to move together and apart. The first frame is rotatably mounted on a second frame to enable "turning at the wrist" movement without limitation. The second frame is pivotally mounted on a third frame to permit 'flexing at the wrist' movement. A hook-driving motor is fixed to the second frame but has a shaft that drives a speed reducer on the first frame which, in turn, drives the hooks. A second motor mounted on the second frame, turns a gear on the first frame to rotate the first frame and the hooks thereon. A third motor mounted on the third frame, turns a gear on a second frame to pivot it.

Wiker, G. A.↗