SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Tester induces cyclic pressure loads across module surface, guaranteeing its mechanical integrity. Module to be tested is sandwiched between stiffened aluminum layers covered with rubber sheets. Automatic front and back pressure loading is cycled by pneumatic system on separate stand. Relief valves prevent overpressuring. Fixture operates at high speed, completing cycle in 5 seconds, and typically applies 2,400 pascals.
Regional building code variations, federal and city codes, and the national electric code are reviewed for their possible effects on the design of photovoltaic modules. Problems that photovoltaic arrays may impose on the insurability of residences are also discussed. Mounting configurations are developed for the modules, and grounding, wiring, terminal, and voltage requirements are established. Installation and materials costs are presented along with performance criteria.
The pressure modulator technique was evaluated for monitoring pollutant gases in the Earth's atmosphere of altitude levels corresponding to the mid and lower troposphere. Using an experimental set up and a 110 cm sample cell, pressure modulator output signals resulting from a range of gas concentrations in the sample cell were examined. Then a 20 cm sample cell was modified so that trace gas properties in the atmosphere could be simulated in the laboratory. These gas properties were measured using an infrared sensor.
An engineering evaluation of thermal energy storage prototypes was performed in order to assess the development status of latent heat storage media. The testing and the evaluation of a prototype sodium hydroxide module is described. This module stored off-peak electrical energy as heat for later conversion to domestic hot water needs.
Direct modulation techniques applicable to integrated optics data preprocessors were investigated. Several methods of modulating a coherent optical beam by interaction with an incoherent beam were studied. It was decided to investigate photon induced conductivity changes in thin semiconductor cladding layers on optical waveguides. Preliminary calculations indicate significant changes can be produced in the phase shift in a propagating wave when the conductivity is changed by ten percent or more. Experimental devices to verify these predicted phase changes and experiments designed to prove the concept are described.
A method and apparatus are described for frequency modulating radiation, such as from a laser, for optoacoustic detectors, interferometers, heterodyne spectrometers, and similar devices. Two oppositely reciprocating cats-eye retroreflectors are used to Doppler modulate the radiation. By reciprocally moving both retroreflectors, the center of mass is maintained constant to permit smooth operation at many Hertz. By slightly offsetting the axis of one retroreflector relative to the other, multiple passes of a light beam may be achieved for greater Doppler shifts with the same reciprocating motion of the retroreflectors.
A process sequence which can be used in conjunction with automated equipment for the mass production of solar cell modules for terrestrial use was developed. The process sequence was then critically analyzed from a technical and economic standpoint to determine the technological readiness of certain process steps for implementation. The steps receiving analysis were: back contact metallization, automated cell array layup/interconnect, and module edge sealing. For automated layup/interconnect, both hard automation and programmable automation (using an industrial robot) were studied. The programmable automation system was then selected for actual hardware development.
This paper deals with analytical and experimental work related to modulation of a semiconductor laser used in high bit rate communication. The approach is based upon minimizing the charge storage effect by a proper choice of the area of the modulating pulses and the bias current. The concept of using additional current pulses to probe for variations in electron density between pulses is investigated. The primary limitation on bit rate is found to be the ability to generate laser drive pulses free of ringing or similar transients. This and the 300 ps pulsewidth, an experimental constraint, limit the bit rate to about 1 Gbit/s. However, by using this approach it appears that bit rates considerably higher than 2 Gbits/s could be reached with sufficiently accurate control of drive pulse shape. It is found that the laser bias and the current pulse area had to be controlled within 1 percent and 10 percent, respectively.
A low cost solar collector capable of operating at 150-200 C is described. An evacuated tube receiver is combined with asymmetric vee-trough concentrators. Peak efficiencies of about 40% at 120 C and 30% at 180 C are expected. Predicted future collector cost is $70/sq m which yields an energy cost of $4.20/GJ at 120 C. During the development of the vee trough/evacuated tube collector both mathematical models to predict thermal and optical performance were developed and tests run to verify theory. The asymmetric vee trough concentrator increases the solar flux intensity for an average value of 2 for year-round performance. Optimized collector module has reflector angles of 55 deg/85 deg. The aperture plane is tilted to the latitude. The reflector is made of electropolished aluminum. The supporting frame is formed by bending sheet metal. Evacuated tube receivers are Pyrex, 15 cm diam and 2.4 m long. The module has 12 tubes on right and left sides altogether. Attainable operation at temperatures on the order of 150-200 C are suitable for absorption refrigeration and power generation via Rankine engines.
Gigahertz analog modulation characteristics of broad-area commercially available GaAlAs lasers have been investigated as a function of temperature and current in the vicinity of the upper frequency limit, where the resonance phenomena occur. The optimum temperature for small-signal amplitude modulation was found to be around -15 C for our particular broad-stripe geometry double-heterostructure laser. The Q was found to increase by a factor of 2 and the bandwidth by about 2%; the external quantum efficiency was maximized in this range. The optimum dc current bias was about 2% above the threshold current. Differential delays have also been measured down to a few picosecond accuracy by a unique phase-angle measurement method using a vector voltmeter. Some of the temperature effects observed may be related to mode changes and multimode and superradiance behavior.
Fine scale magnetic field data from the Voyager 1 and 2 magnetopause and bow shock crossings at Jupiter were analyzed. Explicit models of the dawnside magnetopause and bow shock in Jupiter's orbital plane employ an axisymmetric parabola and hyperbola, respectively, and are determined separately for the encounters. A new phenomenon was discovered in the magnetosheath. It is manifested as (5 or) 10 hour quasi-periodic modulation of the direction of the magnetic field in the outbound magnetosheath, predominantly in the northward (N) and southward (S) directions. It was seen to occur during both encounters and appears most evident in Voyager 2 outbound observations, probably due to the extreme tailward extent of the Voyager 2 trajectory through the magnetosheath. The durations of the N to and from S transitions range from tens of minutes to approximately 3 hours. The directional variation of the field during these transitions is fairly well restricted to a plane parallel to the local model magnetopause location. These signatures may be due to magnetosheath field line draping modulated by the large scale motion of the magnetospheric plasma disk.
A pressure modulator radiometer operated in a nadir viewing mode from the top of a midlatitude summer model of the atmosphere was theoretically studied for monitoring the mean volumetric mixing ratio of carbon monoxide in the troposphere. The mechanical characteristics of the instrument on the Nimbus 7 stratospheric and mesospheric sounder experiment are assumed and CO is assumed to be the only infrared active constituent. A line by line radiative transfer computer program is used to simulate the upwelling radiation reaching the top of the atmosphere. The performance of the instrument is examined as a function of the mean pressure in and the length of the instrument gas correlation cell. Instrument sensitivity is described in terms of signal to noise ratio for a 10 percent change in CO mixing ratio. Sensitivity to mixing ratio changes is also studied. It is concluded that tropospheric monitoring requires a pressure modulator drive having a larger swept volume and producing higher compression ratios at higher mean cell pressures than the Nimbus 7 design.
The technical readiness of a cost effective process sequence that has the potential for the production of flat plate photovoltaic modules which met the price goal in 1986 of $.70 or less per Watt peak was demonstrated. The proposed process sequence was reviewed and laboratory verification experiments were conducted. The preliminary process includes the following features: semicrystalline silicon (10 cm by 10 cm) as the silicon input material; spray on dopant diffusion source; Al paste BSF formation; spray on AR coating; electroless Ni plate solder dip metallization; laser scribe edges; K & S tabbing and stringing machine; and laminated EVA modules.
A teaching module on image classification procedures using the VICAR computer software package was developed to optimize the training benefits for users of the VICAR programs. The field test of the module is discussed. An intensive forest land inventory strategy was developed for Humboldt County. The results indicate that LANDSAT data can be computer classified to yield site specific forest resource information with high accuracy (82%). The "Douglas-fir 80%" category was found to cover approximately 21% of the county and "Mixed Conifer 80%" covering about 13%. The "Redwood 80%" resource category, which represented dense old growth trees as well as large second growth, comprised 4.0% of the total vegetation mosaic. Furthermore, the "Brush" and "Brush-Regeneration" categories were found to be a significant part of the vegetative community, with area estimates of 9.4 and 10.0%.
The purpose of this program is to demonstrate the technical readiness of a cost effective process sequence that has the potential for the production of flat plate photovoltaic modules which met the price goal in 1986 of $.70 or less per watt peak. Program efforts included: preliminary design review, preliminary cell fabrication using the proposed process sequence, verification of sandblasting back cleanup, study of resist parameters, evaluation of pull strength of the proposed metallization, measurement of contact resistance of Electroless Ni contacts, optimization of process parameter, design of the MEPSDU module, identification and testing of insulator tapes, development of a lamination process sequence, identification, discussions, demonstrations and visits with candidate equipment vendors, evaluation of proposals for tabbing and stringing machine.
Progress in the development of automated solar cell and module production is reported. The unimate robot is programmed for the final 35 cell pattern to be used in the fabrication of the deliverable modules. The mechanical construction of the automated lamination station and final assembly station phases are completed and the first operational testing is underway. The final controlling program is written and optimized. The glass reinforced concrete (GRC) panels to be used for testing and deliverables are in production. Test routines are grouped together and defined to produce the final control program.
Numerical solutions are presented of the steady-state modulation of galactic cosmic rays for a realistic two-dimensional model which includes drifts. Calculations of energy spectra and the spatial density variation of protons are shown for a model that incorporates the solar-minimum magnetic field and nominal interplanetary propagation parameters. The calculated values are relatively insensitive to the assumed size of the modulating region and to the magnitude of the particle diffusion coefficient. The solutions show a broad interior 'plateau' in which radial gradients are small. A simple model that neglects diffusion but includes drifts and adiabatic cooling accounts for these results. It is concluded that in this model and the range of parameters, diffusion plays a role secondary to that of drifts and adiabatic cooling.
The high statistics and high resolution rigidity spectra from geomagnetic cutoff to 160 GV/c were provided by a superconducting-magnet spectrometer flown on a balloon. The spectra above 8.3 GV/c fit a power law in rigidity for protons and alphas; below 8.3 GV/c, no clear evidence of solar modification is available. The analysis of data from 5.5 to 8.3 GV/c by the Gleeson-Axford model for solar modulation indicated that the modulation parameter was 0.3 + or - 0.05 Gev/nucleon; the spectra below 5.5 GV/c are being analyzed using a portion of the flight data recorded while the balloon was essentially stationary