Search NASA⌕ Search

SEARCH · Search NASA

Results for “Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Compressibility and strength of nanocrystalline tungsten boride under compression to 60 GPa

The compression behavior and stress state of nanocrystalline tungsten boride (WB) were investigated using radial x-ray diffraction (RXRD) in a diamond-anvil cell under non-hydrostatic compression up to 60.4 GPa. The compression properties and stress state are analyzed using lattice strain theory. Experiments were conducted at beamline X17C of the National Synchrotron Light Source. The radial x-ray diffraction data yield a bulk modulus that is qualitatively consistent with density functional theory calculations and demonstrate that WB is a highly incompressible material. A maximum differential stress, t, of about 14 GPa can be supported by nanocrystalline WB at the highest pressure. This corresponds to about 5% of the shear modulus, G, which is smaller than the values of t/G ({approx}8%-10%) observed for BC{sub 2}N, B{sub 6}O, TiB{sub 2}, and {gamma}-Si{sub 3}N{sub 4} at high pressures. Thus, while WB is highly incompressible, its strength is relatively low at high pressures compared to other hard ceramics.

36 MATERIALS SCIENCE↗

One directional polarized neutron reflectometry with optimized reference layer method

In the past decade, several neutron reflectometry methods for determining the modulus and phase of the complex reflection coefficient of an unknown multilayer thin film have been worked out among which the method of variation of surroundings and reference layers are of highest interest. These methods were later modified for measurement of the polarization of the reflected beam instead of the measurement of the intensities. In their new architecture, these methods not only suffered from the necessity of change of experimental setup but also another difficulty was added to their experimental implementations. This deficiency was related to the limitations of the technology of the neutron reflectometers that could only measure the polarization of the reflected neutrons in the same direction as the polarization of the incident beam. As the instruments are limited, the theory has to be optimized so that the experiment could be performed. In a recent work, we developed the method of variation of surroundings for one directional polarization analysis. In this new work, the method of reference layer with polarization analysis has been optimized to determine the phase and modulus of the unknown film with measurement of the polarization of the reflected neutrons in the same direction as the polarization of the incident beam.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Ion-acoustic cnoidal wave and associated non-linear ion flux in dusty plasma

Using reductive perturbation method with appropriate boundary conditions, coupled evolution equations for first and second order potentials are derived for ion-acoustic waves in a collisionless, un-magnetized plasma consisting of hot isothermal electrons, cold ions, and massive mobile charged dust grains. The boundary conditions give rise to renormalization term, which enable us to eliminate secular contribution in higher order terms. Determining the non secular solution of these coupled equations, expressions for wave phase velocity and averaged non-linear ion flux associated with ion-acoustic cnoidal wave are obtained. Variation of the wave phase velocity and averaged non-linear ion flux as a function of modulus (k{sup 2}) dependent wave amplitude are numerically examined for different values of dust concentration, charge on dust grains, and mass ratio of dust grains with plasma ions. It is found that for a given amplitude, the presence of positively (negatively) charged dust grains in plasma decreases (increases) the wave phase velocity. This behavior is more pronounced with increase in dust concentrations or increase in charge on dust grains or decrease in mass ratio of dust grains. The averaged non-linear ion flux associated with wave is positive (negative) for negatively (positively) charged dust grains in the plasma and increases (decreases) with modulus (k{sup 2}) dependent wave amplitude. For given amplitude, it increases (decreases) as dust concentration or charge of negatively (positively) charged dust grains increases in the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hot-electron generation by “cavitating” Langmuir turbulence in the nonlinear stage of the two-plasmon–decay instability

The kinetic reduced-description particle-in-cell simulation technique has been applied to study the nonlinear stage of two-plasmon–decay (TPD) instability in an inhomogeneous plasma driven by crossed laser beams. The TPD instability is found to be a prolific generator of “cavitating” Langmuir turbulence. Langmuir “cavitons”—localized longitudinal electric fields, oscillating near the local electron plasma frequency, trapped in ponderomotive density depressions—collapse to dimensions of a few electron Debye lengths, where the electric field energy is collisionlessly transferred to electron kinetic energy. The resulting hot electrons can attain instantaneous temperatures up to 100 keV with net suprathermal heat flux out of the system of up to a few percent of the input laser energy. Scaling laws for this hot-electron generation by TPD, in regimes motivated by recent experiments on the Omega laser, were presented recently by Vu et al. (H. X. Vu, D. F. DuBois, D. A. Russell, and J. F. Myatt, Phys. Plasmas 19, 102703 (2012)). This paper concentrates on the microscopic mechanisms for hot-electron generation. The spatial distribution of the maxima of the electric field envelope modulus is found to be very spiky, with the distribution of electric field envelope maxima obeying Gaussian statistics. The cavitons are produced in density-depletion trenches produced by the combined ponderomotive interference of the crossed laser beams and the ponderomotive beats of the primary backward-going TPD Langmuir waves (LWs) resulting from the crossed beams. The Langmuir turbulence is strongest in the electron-density region near 0.241× the laser's critical density, where the forward LWs from the crossed-beam TPD are degenerate. Nucleation of cavitons is assisted by the modulation of the electron density in the trenches, which in turn is caused by the beating of the common forward-going LW and the pair of backward-going LWs. The autocorrelation function of the LW envelope field provides a near-universal shape for intense cavitons—in the neighborhood of the local field maxima. The hot-electron temperature is found to be approximately a linear function of the “caviton temperature” determined from the Gaussian distribution of caviton maxima. These diagnostics provide strong evidence for the importance of Langmuir caviton collapse in the generation of hot electrons by TPD. Extended Zakharov model predictions for TPD exhibit the same qualitative phenomena.

Vu, H. X.↗

Influence of isothermal hot pressing-doping treatment on the electrical and mechanical properties of bulk Bi-Sr-Ca-Cu-O

The influences of (isothermal hot pressing-doping) treatment on the microstructure, electrical and mechanical properties of Bi{sub 2}Sr{sub 3-x}Ca{sub x}Cu{sub 2}O{sub 8+δ} (BSCCO), x ranging from 0.0 to 2 are assessed. BSCCO pellets were prepared by isothermal hot pressing (IHP) technique. The experimental works in this study consists of dc electrical resistivity measurements for electrical and superconducting properties, microhardness tests for mechanical characteristics, powder x-ray diffraction (XRD) for phase analyses (phase ratio), differential thermal analysis (DTA) for melting behaviour and scanning electron microscopy (SEM) for microstructure investigations. The results indicated that the Ca{sup 2+} doping and isothermal hot pressing increased significantly the superconducting transition temperature (T{sup o}{sub c}), which promotes the formation of high-Tc phase. Additionally, Vickers microhardness (VHN), Young's modulus, fracture toughness, brittleness index and elastic stiffness coefficient were also improved. Moreover, IHP-Doping improved the microstructure and the density of the BSCCO studied samples. Microhardness was found to be load dependent. Otherwise, we evaluated the load independent hardness, Young's modulus, fracture toughness and brittleness index of BSCCO samples. The possible reasons for the observed enhancement in electrical and mechanical properties due to (i) the homogeneity of grain region distribution (ii) the enhancement of superconducting phases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Origin of giant permittivity and high-temperature dielectric anomaly behavior in Na{sub 0.5}Y{sub 0.5}Cu{sub 3}Ti{sub 4}O{sub 12} ceramics

Na{sub 0.5}Y{sub 0.5}Cu{sub 3}Ti{sub 4}O{sub 12} ceramics prepared by the conventional solid-state reaction method under various sintering conditions were found to exhibit a giant dielectric constant over 10 000 around room temperature. Two electrical responses were observed in the combined modulus and impedance plots, indicating the presence of Maxwell-Wagner relaxation. The contributions of semiconducting grains and insulating grain boundaries (corresponding to high-frequency and low-frequency electrical response, respectively) played important roles in the dielectric properties of Na{sub 0.5}Y{sub 0.5}Cu{sub 3}Ti{sub 4}O{sub 12} ceramics. The correlations between grain boundaries resistance and low frequency dielectric loss, grains resistance and the position of dielectric loss peak were addressed. Mixed-valent structures of Cu{sup 2+}/Cu{sup 3+} and Ti{sup 3+}/Ti{sup 4+} had been determined using X-ray photoelectron spectroscopy. Electron hopping between Cu{sup 2+} and Cu{sup 3+} and electron transport in Ti{sup 3+}-O-Ti{sup 4+} paths were proposed as the origin of the semiconducting nature of Na{sub 0.5}Y{sub 0.5}Cu{sub 3}Ti{sub 4}O{sub 12} ceramics. In particular, high-temperature dielectric anomaly behavior was investigated in detail. A dielectric peak exhibiting relaxor-like behavior was observed around 200 Degree-Sign C, which was linked with the formation of oxygen vacancies. Based on the electric modulus results, this behavior was explored in the light of the defect formation and explained in terms of a competition process depending on the combinational contribution to polarization between n- and p-type carriers rather than a relaxation process.

36 MATERIALS SCIENCE↗

Dielectric property of NiTiO{sub 3} doped substituted ortho-chloropolyaniline composites

Ortho-chloropolyaniline (OCP)-NiTiO{sub 3} composites have been synthesized via in-situ polymerization of ortho-chloroaniline with various weight percentages of NiTiO{sub 3.} Fourier Transform Infrared spectroscopic studies of Ortho-chloropolyaniline and its composites indicated the formation of composites as a result of Vander Waal's interaction between OCP and NiTiO{sub 3} particles. Surface morphology of OCP and OCP-NiTiO{sub 3} composites were studied using Scanning Electron Microscope (SEM). The SEM micrographs indicated a modified morphology after the composite formation. Dielectric properties and electric modulus of OCP and OCP-NiTiO{sub 3} composites have been investigated in the frequency range of 50 Hz – 5 MHz. It has been noticed that electrical resistance decreases with increase in weight percentage of NiTiO{sub 3} particles in polymer matrix as well as with applied frequency. The display of semicircular arcs in Cole-Cole plots indicates the formation of series resistor and capacitor in network causing a decrease in the relaxation time and as a result conductivity enhances in these composites. The facile and cost effective synthesis process and excellent dielectric and conductivity response of these materials makes them promising materials for practical applications.

36 MATERIALS SCIENCE↗

Thermoelectric and mechanical properties of multi-wall carbon nanotube doped Bi0.4Sb1.6Te3 thermoelectric material

Since many thermoelectrics are brittle in nature with low mechanical strength, improving their mechanical properties is important in fabrication of devices such as thermoelectric power generators and coolers. In this work, multiwall carbon nanotubes (CNTs) were incorporated into polycrystalline Bi0.4Sb1.6Te3 through powder processing, which increased the flexural strength from 32 MPa to 90 MPa. Electrical and thermal conductivities were both reduced in the CNT containing materials, leading to unchanged figure of merit. Dynamic Young s modulus and shear modulus of the composites were lower than the base material, which is likely related to the grain boundary scattering due to the CNTs.

mechanical strength↗

Response to “Comment on ‘Motion of a helical vortex filament in superfluid {sup 4}He under the extrinsic form of the local induction approximation”’ [Phys. Fluids 26, 019101 (2014)]

I agree with the authors regarding their comments on the Donnelly-Glaberson instability for such helical filaments as those obtained in my paper. I also find merit in their derivation of the quantum LIA (local induction approximation) in the manner of the LIA of Boffetta et al. However, I disagree with the primary criticisms of Hietala and Hänninen. In particular, though they suggest LIA and local nonlinear equation modes are not comparable since the former class of models contains superfluid friction parameters, note that since these parameters are small one may take them to zero and consider a qualitative comparison of the models (which is what was done in my paper). Second, while Hietala and Hänninen criticize certain assumptions made in my paper (and the paper of Shivamoggi where the model comes from) since the results break-down when Ak → ∞, note that in my paper I state that any deviations from the central axis along which the filament is aligned must be sufficiently bounded in variation. Therefore, it was already acknowledged that Ak(=|Φ{sub x}|) should be sufficiently bounded, precluding the Ak → ∞ case. I also show that, despite what Hietala and Hänninen claim, the dispersion relation obtained in my paper is consistent with LIA, where applicable. Finally, while Hietala and Hänninen claim that the dispersion parameter should be complex valued, I show that their dispersion relation is wrong, since it was derived incorrectly (they assume the complex modulus of the potential function is constant, yet then use this to obtain a potential function with non-constant modulus)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Strength and equation of state of NaCl from radial x-ray diffraction

The strength and equation of state of NaCl were determined under nonhydrostatic compression up to 27 GPa using an energy-dispersive radial x-ray diffraction technique in a diamond-anvil cell using the lattice strain theory. Together with estimation of the high-pressure shear modulus, it is suggested that NaCl could support a maximum differential stress of 0.980 GPa at 22.6 GPa under uniaxial compression. The differential stress rapidly drops at 27.2 GPa due to the phase transition from B1 phase to B2 phase for NaCl. The hydrostatic compression data of B1 phase yield a bulk modulus K{sub 0} = 25.6(8) GPa and its pressure derivative K{sub 0}′ = 5.16(20) using Pt pressure scale. In addition, a comparative study of the observed pressures from Pt scale and ruby-fluorescence scale shows that the ruby-fluorescence pressures may reflect the lower stress state under nonhydrostatic compression compared with hydrostatic compression.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Equation of state of rhenium and application for ultra high pressure calibration

The isothermal equation of state of rhenium has been measured by powder X-ray diffraction experiments up to 144 GPa at room temperature in a diamond anvil cell. A helium pressure transmitting medium was used to minimize the non-hydrostatic stress on the sample. The fit of pressure-volume data yields a bulk modulus K{sub 0} = 352.6 GPa and a pressure derivative of the bulk modulus K′{sub 0}=4.56. This equation of state differs significantly from a recent determination [Dubrovinsky et al., Nat. Commun. 3, 1163 (2012)], giving here a lower pressure at a given volume. The possibility of using rhenium gasket X-ray diffraction signal, with the present equation of state, to evaluate multi-Mbar pressures in the chamber of diamond anvil cells is discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Maximal quantum mechanical symmetry: Projective representations of the inhomogeneous symplectic group

A symmetry in quantum mechanics is described by the projective representations of a Lie symmetry group that transforms between physical quantum states such that the square of the modulus of the states is invariant. The Heisenberg commutation relations that are fundamental to quantum mechanics must be valid in all of these physical states. This paper shows that the maximal quantum symmetry group, whose projective representations preserve the Heisenberg commutation relations in this manner, is the inhomogeneous symplectic group. The projective representations are equivalent to the unitary representations of the central extension of the inhomogeneous symplectic group. This centrally extended group is the semidirect product of the cover of the symplectic group and the Weyl-Heisenberg group. Its unitary irreducible representations are computed explicitly using the Mackey representation theorems for semidirect product groups.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High pressure phase transformation in yttrium sulfide(YS): A first principle study

First principles calculations have been carried out to analyze structural, elastic and dynamic stability, of YS under hydrostatic compression. The comparison of enthalpies of rocksalt type (B1) and CsCl type cubic (B2) structures determined as a function of compression suggests the B1→B2 transition at ∼ 49 GPa. Various physical quantities such as zero pressure equilibrium volume, bulk modulus, and pressure derivative of bulk modulus have been derived from the theoretically determined equation of state. The single crystal elastic constants derived from the energy strain method agree well with the experimental values. The activation barrier between B1 and B2 phases calculated at transition point is ∼ 17/mRy/formula unit. Our lattice dynamic calculations show that at ambient condition, the B1 phase is lattice dynamically stable and frequencies of phonon modes in different high symmetry directions of Brillouin zone agrees well with experimental values. The B2 phase also is dynamical stable at ambient condition as well as at ∼ 49 GPa, supporting our static lattice calculation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ab-initio calculation of ZnGeAs{sub 2} semiconductor

The structural, electronic, optical and elastic properties of ZnGeAs{sub 2} semiconductor have been investigated using pseudopotential plane wave method within the density functional theory (DFT). The optimized lattice constants, energy gap and crystal field splitting parameter are calculated. The optical properties such as dielectric function, optical reflectivity,, extinction coefficient, absorption spectra, refractive index and electron energy loss spectrum have been studied. The values of bulk modulus (B), elastic constants (C{sub ij}), Young’s modulus (Y), Zener anisotropic factor (A), Poisson’s ratio (ν) and Debye temperature (Θ{sub D}) have been calculated. The calculated values of all these parameters are compared with the available experimental values and the values reported by different workers. A fairly good agreement has been found between them.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Relaxation behavior of oxygen deficient strontium manganite

Conduction behavior of nanocrystalline oxygen deficient ceramic-SrMnO{sub 3–δ}(δ∼0.14) has been studied. The structural analysis of nano-SrMnO{sub 2.86} follows hexagonal unit cell structure with P6{sub 3}/mmc (194) space group belonging to 6/mmm point group with 4H – layered type hexagonal-cubic layers. The system have lattice parameters; a = 5.437(92) Å, c = 9.072(92) Å, c/a∼1.66 (85) with α =90° γ= 120° and cell volume, V= 232.35(18). The relaxation times estimated from complex impedance and modulus relaxation spectrum, show the thermally activated system with corresponding activation energies as 0.66 eV and 0.51 eV The stretching factor ‘β’ from the scaled modulus spectrum shows the poly-dispersive non-Debye nature of the system. The hopping number ‘n’ shows the influence of ionic charge carriers which controls the conduction mechanism of nano-SrMnO{sub 2.86}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of electron beam irradiation on mechanical and thermal properties of polypropylene/polyamide blend

The effects of electron beam irradiation on the mechanical and thermal properties of polypropylene (PP) and polyamide6 (PA6) blends-with talc 20 wt% as filler, SEBS-g-MAH as compatibilizer, and triallyl isocyanurate as crosslinking agent-were investigated. Although the tensile and flexural moduli and strengths of the PP/PA6 blends with talc, SEBS-g-MAH, and TAIC could be increased by the application of electron beam irradiation, the impact strength was decreased. Ddifferential scanning calorimetryer measurements showed that the melting temperatures of all PP/PA6 blends were decreased with increases in the electron beam irradiationdose. From dynamic mechanical analyzer results, a storage modulus curve in the plateau region was observed only in the PP/PA6 blends with talc, SEBS-g-MAH, and TAIC; the storage modulus increased with increasing electron beam irradiation dose, indicating that the three-dimensional network developed gradually in the more amorphous PA6. As a result, the most significant improvement observed in heat distortion tests under high load (1.8 MPa) occurred at 200 kGy.

36 MATERIALS SCIENCE↗

Equation of state for Eu-doped SrSi{sub 2}O{sub 2}N{sub 2}

α-SrSi{sub 2}O{sub 2}N{sub 2} is one of the recently studied oxonitridosilicates applicable in optoelectronics, in particular in white LEDs. Its elastic properties remain unknown. A survey of literature shows that, up to now, nine oxonitridosilicate materials have been identified. For most of these compounds, doped with rare earths and manganese, a luminescence has been reported at a wavelength characteristic for the given material; all together cover a broad spectral range. The present study focuses on the elastic properties of one of these oxonitridosilicates, the Eu-doped triclinic α-SrSi{sub 2}O{sub 2}N{sub 2}. High-pressure powder diffraction experiments are used in order to experimentally determine, for the first time, the equation of state of this compound. The in situ experiment was performed for pressures ranging up to 9.65 GPa, for Eu-doped α-SrSi{sub 2}O{sub 2}N{sub 2} sample mounted in a diamond anvil cell ascertaining the hydrostatic compression conditions. The obtained experimental variation of volume of the triclinic unit cell of α-SrSi{sub 2}O{sub 2}N{sub 2}:Eu with rising pressure served for determination of the Birch-Murnaghan equation of state. The determined above quoted bulk modulus is 103(5) GPa, its first derivative is 4.5(1.1). The above quoted bulk modulus value is found to be comparable to that of earlier reported oxynitrides of different composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗