Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES, FLAT - STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Investigation of test methods, material properties, and processes for solar cell encapsulants. Encapsulation task of the low-cost silicon solar array project

During this quarter, flat-plate solar collector systems were considered and six basic construction elements were identified: outer coatings, superstrates, pottants, substrates, undercoats, and adhesives. Materials surveys were then initiated to discover either generic classes or/and specific products to function as each construction element. Cost data included in the surveys permit ready evaluation of each material. Silicones, fluorocarbons, glass, and acrylic polymers have the highest inherent weatherability of materials studied to date. Only acrylics, however, combine low costs, environmental resistance, and potential processability. This class will receive particular emphasis.

Source record↗

Induced velocity field of a jet in a crossflow

An experimental investigation of a subsonic round jet exhausting perpendicularly from a flat plate into a subsonic crosswind of the same temperature was conducted. Velocity and pressure measurements were made in planes perpendicular to the path of the jet for ratios of jet velocity to crossflow velocity ranging from 3 to 10. The results of these measurements are presented in tabular and graphical forms. A pair of diffuse contrarotating vortices is identified as a significant feature of the flow, and the characteristics of the vortices are discussed.

Fearn, R. L.↗

Impact of Balance Of System (BOS) costs on photovoltaic power systems

The Department of Energy has developed a program to effect a large reduction in the price of photovoltaic modules, with significant progress already achieved toward the 1986 goal of 50 cents/watt (1975 dollars). Remaining elements of a P/V power system (structure, battery storage, regulation, control, and wiring) are also significant cost items. The costs of these remaining elements are commonly referred to as Balance-of-System (BOS) costs. The BOS costs are less well defined and documented than module costs. The Lewis Research Center (LeRC) in 1976/77 and with two village power experiments that will be installed in 1978. The costs were divided into five categories and analyzed. A regression analysis was performed to determine correlations of BOS Costs per peak watt, with power size for these photovoltaic systems. The statistical relationship may be used for flat-plate, DC systems ranging from 100 to 4,000 peak watts. A survey of suppliers was conducted for comparison with the predicted BOS cost relationship.

Hein, G. F.↗

Finite element analysis of periodic transonic flow problems

Flow about an oscillating thin airfoil in a transonic stream was considered. It was assumed that the flow field can be decomposed into a mean flow plus a periodic perturbation. On the surface of the airfoil the usual Neumman conditions are imposed. Two computer programs were written, both using linear basis functions over triangles for the finite element space. The first program uses a banded Gaussian elimination solver to solve the matrix problem, while the second uses an iterative technique, namely SOR. The only results obtained are for an oscillating flat plate.

Fix, G. J.↗

Cost of photovoltaic energy systems as determined by balance-of-system costs

The effect of the balance-of-system (BOS), i.e., the total system less the modules, on photo-voltaic energy system costs is discussed for multikilowatt, flat-plate systems. Present BOS costs are in the range of 10 to 16 dollars per peak watt (1978 dollars). BOS costs represent approximately 50% of total system cost. The possibility of future BOS cost reduction is examined. It is concluded that, given the nature of BOS costs and the lack of comprehensive national effort focussed on cost reduction, it is unlikely that BOS costs will decline greatly in the next several years. This prognosis is contrasted with the expectations of the Department of Energy National Photovoltaic Program goals and pending legislation in the Congress which require a BOS cost reduction of an order of magnitude or more by the mid-1980s.

Rosenblum, L.↗

Heat transfer distributions induced by elevon deflections on swept wings and adjacent surfaces at Mach 6

Surface heat transfer distributions are presented for swept wing semispan models having trailing edge elevon ramp angles of 0, 10, 20, and 30 degrees. The wing sweepback angles are 0, 50, and 70 degrees. The models have attachable cylindrical and flat plate center bodies and various attachable wing-tip fins. The data, obtained for a 0 degree angle of attack, a free stream Mach number of 6, and a wing root chord Reynolds number of about 17,000,000, reveal considerably larger regions of elevon induced thermal loads on adjacent surfaces than would be suggested by fully attached flow analyses.

Johnson, C. B.↗

Boundary layer, skin friction, and boattail pressure measurements from the YF-12 airplane at Mach numbers up to 3

In-flight measurements of boundary layer and skin friction data were made on YF-12 airplanes for Mach numbers between 2.0 and 3.0. Boattail pressures were also obtained for Mach numbers between 0.7 and 3.0 with Reynolds numbers up to four hundred million. Boundary layer data measured along the lower fuselage centerline indicate local displacement and momentum thicknesses can be much larger than predicted. Skin friction coefficients measured at two of five lower fuselage stations were significantly less than predicted by flat plate theory. The presence of large differences between measured boattail pressure drag and values calculated by a potential flow solution indicates the presence of vortex effects on the upper boattail surface. At both subsonic and supersonic speeds, pressure drag on the longer of two boattail configurations was equal to or less than the pressure drag on the shorter configuration. At subsonic and transonic speeds, the difference in the drag coefficient was on the order of 0.0008 to 0.0010. In the supersonic cruise range, the difference in the drag coefficient was on the order of 0.002. Boattail drag coefficients are based on wing reference area.

Fisher, D. F.↗

Terrestrial central station array life-cycle analysis support study

Plant elements evaluated included designs for module, panel and array structures, as well as balance-of-plant systems. Installation and maintenance procedures and the impact of site environment were also evaluated. In terms of the cost of energy produced, the horizontal array configuration was found to be less expensive than the tandem array at latitudes less than 40 deg. Both of these configurations are less expensive than the rack design. However, the costs of energy for all three configurations are within approximately ?10 percent of each other. For flat plate panels, the seasonally adjusted and tracking array configurations are not economically attractive when compared to the three other designs. Balance-of-plant costs are approximately equal to (goal) module costs. The array structures and foundations are the most expensive items in the balance-of-plant costs.

Source record↗

Tandem photovoltaic solar cells and increased solar energy conversion efficiency

Tandem photovoltaic cells, as proposed by Jackson (1955) to increase the efficiency of solar energy conversion, involve the construction of a system of stacked p/n homojunction photovoltaic cells composed of different semiconductors. It had been pointed out by critics, however, that the total power which could be extracted from the cells in the stack placed side by side was substantially greater than the power obtained from the stacked cells. A reexamination of the tandem cell concept in view of the development of the past few years is conducted. It is concluded that the use of tandem cell systems in flat plate collectors, as originally envisioned by Jackson, may yet become feasible as a result of the development of economically acceptable solar cells for large scale terrestrial power generation.

Loferski, J. J.↗

Effect of ice contamination on liquid-nitrogen drops in film boiling

Previously reported vaporization time data of liquid nitrogen drops in film boiling on a flat plate are about 30 percent shorter than predicted from standard laminar film boiling theory. This theory, however, had been found to successfully correlate the data for conventional fluids such as water, ethanol, benzene, or carbon tetrachloride. This paper presents experimental evidence that some of the discrepancy for cryogenic fluids results from ice contamination due to condensation. The data indicate a fairly linear decrease in droplet evaporation time with the diameter of the ice crystal residue. After correcting the raw data for ice contamination along with convection, a comparison of theory with experiment shows good agreement.

Schoessow, G. J.↗

Correlation of turbulent shear layer attachment peak heating near Mach 6

A correlation of new turbulent two-dimensional data and peak heating data for attaching free shear layers is presented for a 2.54-cm and 5.08-cm diam cylindrical leading-edge slab 25.4 cm long, and 7.62 and 10.16 cm wide. A 30.48 x 25.4 cm sharp leading-edge flat plate set at 15 and 20 deg is used to generate plane impinging shocks. The freestream Mach number is 6 and the freestream Reynolds number varies from 3,300,000 to 25,600,000/m. Peak heating is measured on silica-based epoxy models with a phase change coating technique. A comparison of the free shear layer data with the transition data of Birch and Keyes (1972) reveals that the shear layer data are turbulent at attachment. The trend of the data shows that peak heating is strongly affected by the state of development at attachment. As the free shear layers become more fully developed, the data approach the two-dimensional correlation. Persistence of transitional flow structures for supersonic free shear flows is pointed out.

Keyes, J. W.↗

Thin-layer approximation and algebraic model for separated turbulent flows

An algebraic turbulence model for two- and three-dimensional separated flows is specified that avoids the necessity for finding the edge of the boundary layer. Properties of the model are determined and comparisons made with experiment for an incident shock on a flat plate, separated flow over a compression corner, and transonic flow over an airfoil. Separation and reattachment points from numerical Navier-Stokes solutions agree with experiment within one boundary-layer thickness. Use of law-of-the-wall boundary conditions does not alter the predictions significantly. Applications of the model to other cases are contained in companion papers.

Baldwin, B.↗

Numerical solution of a three-dimensional shock wave and turbulent boundary-layer interaction

A rapid numerical scheme is used to solve the complete mass-averaged Navier-Stokes equations for supersonic turbulent flow over a three-dimensional compression corner. A simple eddy viscosity model is developed, and the interaction of a swept shock wave and a three-dimensional turbulent boundary layer is studied. Good agreement is obtained between the present results and experimental measurements for the case of a wedge with an angle of 6 deg on a flat-plate sidewall. For the case of a 12-deg wedge angle, the computed results do not show the existence of a peak pressure found experimentally. However, the range of interaction, the plateau pressure, and the peak heat transfer are closely predicted for all cases. The high heat transfer near the axial corner is due to the thinning of the boundary layer and inflow of fresh high-momentum fluid. The heat transfer is relieved through pressure reduction and boundary-layer thickening.

Hung, C. M.↗

An ultralightweight, evacuated, load-bearing, high-performance insulation system

A new hollow-glass microsphere insulation and a flexible stainless-steel vacuum jacket were demonstrated on a flight-weight cryogenic test tank, 1.17 m in diameter. The weight of the system is three times lighter than the most advanced vacuum-jacketed design demonstrated to date, a free-standing honeycomb hard shell with a multilayer insulation system (for a Space Tug application). Design characteristics of the flexible vacuum jacket are presented along with a model describing the insulation thermal performance as a function of boundary temperatures and emittance, compressive load on the insulation and insulation gas pressure. Test data are compared with model predictions and with prior flat-plate calorimeter test results. Potential applications for this insulation system or a derivative of this system include the cryogenic Space Tug, the Single-Stage-to-Orbit Space Shuttle, LH2 fueled subsonic and hypersonic aircraft, and LNG applications.

Parmley, R. T.↗

Temperature control analysis and flight results for the Viking Orbiter 1975 Mars atmospheric water detection instrument

The Mars atmospheric water detector (MAWD) instrument required a temperature of -70 C at the detector. The monochromator housing required +20 C + or - 1 C. This instrument was located on the scan platform, and slewed across two solar panels. The thermal design for the detector was an open flat plate radiator thermally isolated on four 1-in. tubes, with a flexible strap to the detector. MAWD radiator view factors and heat loads from the spacecraft were determined for the Lander on and off, for all angular positions of the scan platform. Subsystem and system tests were performed using the 25-ft diameter solar simulator. In-flight results have shown no anomalies, and no degradation has been observed. Servo-controlled heaters are used to control the temperature.

Kavanagh, H. M.↗

Round jet in a cross flow - Influence of injection angle on vortex properties

A model is developed to infer the properties of a pair of diffuse contrarotating vortices for perpendicular jet injection into the cross flow. Attention is given to pressure distribution on the surface where the jet exhausts, especially in terms of V/STOL applications. A V/STOL wind tunnel experiment is described, whereby a round jet of air (10.16 cm dia) was discharged through a horizontal flat plate into the cross flow of the wind tunnel test section at angles of 45, 60, 75, and 90 deg. Results indicate that the effective vortex strength for both velocity ratios is highest near the jet orifice, and decreases as the vortices are swept downstream, at which point the effective vortex spacing increases. In addition, the core radius of the vortex exhibits properties similar to those of the effective vortex spacing

Krausche, D.↗

Drag and heat transfer on surfaces with small longitudinal fins

An investigation is conducted regarding the drag characteristics of longitudinally ribbed surfaces using various configurations which attempt to confine the turbulent wall bursts to regions of small transverse extent in the initial birth region. The ratio of heat transfer increase to drag increase for the high area ratio rib configurations is determined and the heat transfer efficiency of the present surfaces is compared with data found in the literature. The drag data obtained indicate local 'wetted area skin friction' reductions but due to the increased surface area the planform drag is increased in most instances. There is no indication of drag reduction with the rectangular ribbed models that had sharp leading and fin tip edges. Heat transfer data indicate that several of the triangular grooved models have efficiencies approximately 10 percent higher than that of a smooth flat plate.

Walsh, M. J.↗