Search NASA⌕ Search

SEARCH · Search NASA

Results for “System Study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Systems design study of the Pioneer Venus spacecraft. Appendices to volume 1, sections 8-11 (part 3 of 3)

Power subsystem cost/weight tradeoffs are discussed for the Venus probe spacecraft. The cost estimations of power subsystem units were based upon DSCS-2, DSP, and Pioneer 10 and 11 hardware design and development and manufacturing experience. Parts count and degree of modification of existing hardware were factored into the estimate of manufacturing and design and development costs. Cost data includes sufficient quantities of units to equip probe bus and orbiter versions. It was based on the orbiter complement of equipment, but the savings in fewer slices for the probe bus balance the cost of the different probe bus battery. The preferred systems for the Thor/Delta and for the Atlas/Centaur are discussed. The weights of the candidate designs were based upon slice or tray weights for functionally equivalent circuitry measured on existing hardware such as Pioneers 10 and 11, Intelsat 3, DSCS-2, or DSP programs. Battery weights were based on measured cell weight data adjusted for case weight or off-the-shelf battery weights. The solar array weight estimate was based upon recent hardware experience on DSCS-2 and DSP arrays.

Source record↗

Connected Lighting Systems Efficiency Study: PoE Cable Energy Losses, Part 2

Power over Ethernet (PoE) technology offers the ability to provide both low-voltage direct current (DC) power and communication over a standard Ethernet cable—also referred to as a local area network (LAN) cable or Category cable. Light-emitting diode (LED) technology has reduced the power required for lighting applications, while advances in PoE standards and technology have yielded substantial increases in the amount of power that can be delivered to a networked device over a single cable. As a result, PoE technology is emerging in lighting and many other applications beyond its historical foothold in telephony and networking equipment. Several major LED luminaire manufacturers have introduced PoE connected lighting systems in recent years, making this a potentially disruptive technology. PoE lighting systems can offer improved efficiency relative to traditional line voltage alternating current (AC) systems, because AC-DC power conversion losses can be reduced if this work is consolidated among one or more PoE switches, rather than being distributed among a greater number of smaller LED drivers. However, this effect can be offset to some extent by increased losses associated with an increased voltage drop in the low-voltage Ethernet cabling. In fact, these losses could exceed 15% in poorly designed systems. Aspects of cable design that can affect cable energy performance include American Wire Gauge (AWG), Category (e.g., 5e), shielding, and fire rating (e.g., CMP). Installation practices (e.g., bending, bundling, conduit) can also affect cable performance. Although cable energy losses can be predicted with knowledge of conductor DC resistance (DCR), and DCR can be estimated based on rated AWG, most product datasheets state maximum DCR - or reference standards that specify DCR limits - in lieu of nominal DCR.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Power Extension Package (PEP) system definition extension, orbital service module systems analysis study. Volume 1: Executive summary

An array deployment assembly, power regulation and control assembly, the necessary interface, and display and control equipment comprise the power extension package (PEP) which is designed to provide increased power and duration, as well as reduce fuel cell cryogen consumption during Spacelab missions. Compatible with all currently defined missions and payloads, PEP imposes minimal weight and volume penalties on sortie missions, and can be installed and removed as needed at the launch site within the normal Orbiter turnaround cycle. The technology on which it is based consists of a modified solar electric propulsion array, standard design regulator and control equipment, and a minimally modified Orbiter design. The requirements from which PEP was derived, and the system and its performance capabilities are described. Features of the recommended project are presented.

Source record↗

Bibliography of Supersonic Cruise Research (SCR) program from 1977 to mid-1980

The supersonic cruise research (SCR) program, initiated in July 1972, includes system studies and the following disciplines: propulsion, stratospheric emission impact, structures and materials, aerodynamic performance, and stability and control. In a coordinated effort to provide a sound basis for any future consideration that may be given by the United States to the development of an acceptable commercial supersonic transport, integration of the technical disciplines was undertaken, analytical tools were developed, and wind tunnel, flight, and laboratory investigations were conducted. The present bibliography covers the time period from 1977 to mid-1980. It is arranged according to system studies and the above five SCR disciplines. There are 306 NASA reports and 135 articles, meeting papers, and company reports cited.

Hoffman, S.↗

Space station systems analysis study. Part 2, volume 3: Appendixes, Book 2: Supporting data (7 through 18)

Topics discussed include: (1) design considerations for a MARS sample return laboratory module for space station investigations; (2) crew productivity as a function of work shift arrangement; (3) preliminary analysis of the local logistics problem on the space construction base; (4) mission hardware construction operational flows and timelines; (5) orbit transfer vehicle concept definition; (6) summary of results and findings of space processing working review; (7) crew and habitability subsystem (option L); (8) habitability subsystem considerations for shuttle tended option L; (9) orbiter utilization in manned sortie missions; (10) considerations in definition of space construction base standard module configuration (option L); (11) guidance, control, and navigation subsystems; and (12) system and design tradeoffs.

Source record↗

Experimental Setup and Learning-Based AI Model for Developing Accurate PV Inverter Models

The integration of power electronics-based interfaces presents challenges due to the absence of detailed models and the high computational complexity. Generic models used in system studies lack accuracy in capturing converter dynamics. This paper proposes a data-driven approach developed from experimental setup data. This approach enhances accuracy in photovoltaic inverter modeling. We used two types of PV inverters in the experiment. The recorded experimental data undergo processing through a machine learning model. Results from the model trained through machine learning is also presented.

artificial intelligence↗

National Aero-Space Plane technology development overview

The paper discusses the management structure and organization that was developed in early 1986 to focus the national technology resource pool on the enabling technologies for the NASP. The NASP program is developing technologies in parallel with total system studies that are aimed at single stage to orbit (SSTO) capability. In order to manage the technology development seven teams were established by discipline and charged with the task of recommending specific programs to be funded by the NASP Joint Program Office (JPO). The teams were staffed by representatives from NASA Research Centers, Johns Hopkins University, and the Air Force Laboratories at Wright-Patterson AFB. In addition several special teams were established to recommend development programs for specific areas of technical concern that became apparent when the total system studies identified the technology to be critical and sensitive in the analysis that would enable a single stage to orbit vehicle.

Wright, Howard T.↗

Conceptual design of an airborne laser Doppler velocimeter system for studying wind fields associated with severe local storms

An airborne laser Doppler velocimeter was evaluated for diagnostics of the wind field associated with an isolated severe thunderstorm. Two scanning configurations were identified, one a long-range (out to 10-20 km) roughly horizontal plane mode intended to allow probing of the velocity field around the storm at the higher altitudes (4-10 km). The other is a shorter range (out to 1-3 km) mode in which a vertical or horizontal plane is scanned for velocity (and possibly turbulence), and is intended for diagnostics of the lower altitude region below the storm and in the out-flow region. It was concluded that aircraft flight velocities are high enough and severe storm lifetimes are long enough that a single airborne Doppler system, operating at a range of less than about 20 km, can view the storm area from two or more different aspects before the storm characteristics change appreciably.

Thomson, J. A. L.↗

Large-Scale Boundary Layer Ingesting Propulsor Research

NASA’s Advanced Air Transport Technology (AATT) project is investigating boundary layer ingesting (BLI) propulsors for advanced subsonic commercial vehicle concepts to enable the reduction of fuel burn. A multidisciplinary team of researchers from NASA, United Technologies Research Center (UTRC), Virginia Polytechnic University, and the Air Force Arnold Engineering Development Complex developed and tested an embedded BLI inlet and distortion-tolerant fan (BLI2DTF) system in the NASA Glenn Research Center (GRC) 8- foot by 6-foot (8x6) transonic wind tunnel. The test demonstrated the component performance goals necessary for an overall fuel burn reduction of 3 to 5 percent on a large hybrid wing body (HWB) aircraft. Special test equipment, including a raised floor with flow effectors and a bleed system, was developed for use in the 8x6 to produce the appropriate incoming boundary layer representative of an HWB application. Detailed measurements were made to determine the inlet total pressure loss and distortion, fan stage efficiency, and aeromechanic performance including blade vibration stress and displacement response. Results from this test were used as input to a vehicle-level system study performed by the AATT project to assess the impact of BLI on an alternative advanced concept aircraft referred to as the NASA D8 (ND8), which is somewhat similar to the HWB in its integration of the propulsor. This paper will provide an overview of the project timeline, special test equipment needed in the wind tunnel to develop the appropriate incoming boundary layer, and the difficulties in designing a propulsor for the test. The paper will conclude with some representative aerodynamic and aeromechanic data from the test itself and conclude with how this data was used in the ND8 system study.

Aerodynamic performance↗

Large-Scale Boundary Layer Ingesting Propulsor Research

_NASA's Advanced Air Transport Technology (AATT) project is investigating boundary layer ingesting (BLI) propulsors for advanced subsonic commercial vehicle concepts to enable the reduction of fuel burn. A multidisciplinary team of researchers from NASA, United Technologies Research Center (UTRC), Virginia Polytechnic University, and the Air Force Arnold Engineering Development Complex developed and tested an embedded BLI inlet and distortion-tolerant fan (BLI2DTF) system in the NASA Glenn Research Center (GRC) 8-foot by 6-foot (8x6) transonic wind tunnel. The test demonstrated the component performance goals necessary for an overall fuel burn reduction of 3 to 5 percent on a large hybrid wing body (HWB) aircraft. Special test equipment, including a raised floor with flow effectors and a bleed system, was developed for use in the 8x6 to produce the appropriate incoming boundary layer representative of an HWB application. Detailed measurements were made to determine the inlet total pressure loss and distortion, fan stage efficiency, and aeromechanic performance including blade vibration stress and displacement response. Results from this test were used as input to a vehicle-level system study performed by the AATT project to assess the impact of BLI on an alternative advanced concept aircraft referred to as the NASA D8 (ND8), which is somewhat similar to the HWB in its integration of the propulsor. This paper will provide an overview of the project timeline, special test equipment needed in the wind tunnel to develop the appropriate incoming boundary layer, and the difficulties in designing a propulsor for the test. The paper will conclude with some representative aerodynamic and aeromechanic data from the test itself and conclude with how this data was used in the ND8 system study.

Celestina, Mark L.↗

Onboard Inert Gas Generation System/Onboard Oxygen Gas Generation System (OBIGGS/OBOGS) Study: Gas Separation Technology--State of the Art - Part 2

This purpose of this contract study task was to investigate the State of the Art in Gas Separation Technologies utilized for separating air into both nitrogen and oxygen gases for potential applications on commercial aircraft. The intended applications included: nitrogen gas for fuel tank inerting, cargo compartment fire protection, and emergency oxygen for passenger and crew use in the event of loss of cabin pressure. The approach was to investigate three principle methods of gas separation: Hollow Fiber Membrane (HFM), Ceramic Membrane (CM), and liquefaction: Total Atmospheric Liquefaction of Oxygen and Nitrogen (TALON). Additional data on the performance of molecular sieve pressure swing adsorption (PSA) systems was also collected and discussed. Performance comparisons of these technologies are contained in the body of the report.

Reynolds, Thomas L.↗

A turbojet-boosted two-stage-to-orbit space transportation system design study

The concept to use twin turbo-powered boosters for acceleration to supersonic staging speed followed by an all rocket powered orbiter stage was proposed. A follow-on design study was then made of the concept with the performance objective of placing a 29,483 Kg payload into a .2.6 X 195.3 km orbit. The study was performed in terms of analysis and trade studies, conceptual design, utility and economic analysis, and technology assessment. Design features of the final configuration included: strakes and area rule for improved take off and low transonic drag, variable area inlets, exits and turbine, and low profile fixed landing gear for turbojet booster stage. The payload required an estimated GLOW of 1,270,000 kg for injection in orbit. Each twin booster required afterburning turbojet engines each with a static sea level thrust rating of 444,800 N. Life cycle costs for this concept were comparable to a SSTO/SLED concept except for increased development cost due to the turbojet engine propulsion system.

Hepler, A. K.↗

What Levels of Coupled Cluster Theory Are Appropriate for Transition Metal Systems? A Study Using Near-Exact Quantum Chemical Values for 3d Transition Metal Binary Compounds

Transition metal compounds are traditionally considered to be challenging for standard quantum chemistry approximations like coupled cluster (CC) theory, which are usually employed to validate lower level methods like density functional theory (DFT). To explore this issue, we present a database of bond dissociation energies (BDEs) for 74 spin states of 69 diatomic species containing a 3d transition metal atom and a main group element, in the moderately sized def2-SVP basis. The presented BDEs appear to have an (estimated) 3σ error less than 1 kJ/mol relative to the exact solutions to the nonrelativistic Born-Oppenheimer Hamiltonian. These benchmark values were used to assess the performance of a wide range of standard single reference CC models, as the results should be beneficial for understanding the limitations of these models for transition metal systems. We find that interactions between metals and monovalent ligands like hydride and fluoride are well described by CCSDT. Similarly, CCSDTQ appears to be adequate for bonds between metals and nominally divalent ligands like oxide and sulfide. However, interactions with polyvalent ligands like nitride and carbide are more challenging, with even CCSDTQ(P)Λ yielding errors on the scale of a few kJ/mol. We also find that many perturbative and iterative approximations to higher order terms either yield disappointing results or actually worsen the performance relative to the baseline low level CC method, indicating that complexity does not always guarantee accuracy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Fusion Nuclear Science Facility, the Critical Step in the Pathway to Fusion Energy

The proposed Fusion Nuclear Science Facility (FNSF) represents the first facility to enter the complex fusion nuclear regime, and its technical mission and attributes are being developed. The FNSF represents one part of the fusion energy development pathway to the first commercial power plant with other major components being the pre-FNSF research and development, research in parallel with the FNSF, pre-DEMO research and development, and the demonstration power plant (DEMO). Finally, the Fusion Energy Systems Studies group is developing the technical basis for the FNSF in order to provide a better understanding of the demands on the fusion plasma and fusion nuclear science programs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Inferring precocial Chinook Salmon production through single‐parentage assignments

Abstract Objective Parentage analysis is a routine methodology in fisheries research, but study systems exist where it is impractical to sample both parents. The ability to reliably assign offspring to a single parent is beneficial in these situations. We applied single‐parentage assignments to a naturally spawning population of Chinook Salmon Oncorhynchus tshawytscha to quantify production of anadromous returns by unsampled precocial males. Methods We used an approach that focused on two important aspects of parentage analyses: (1) addressing the presence of family structure within the set of sampled parents and (2) controlling for false‐positive and false‐negative assignments. Result Results indicated that 30% of reproductively successful males were precocial males, which produced 20% of the returning anadromous offspring. Conclusion This study provides a framework for applying single‐parent assignments in a salmonid study system while explicitly addressing sources of assignment errors.

Steele, Craig A.↗

Satellite services system analysis study. Volume 1, part 2: Executive summary

The early mission model was developed through a survey of the potential user market. Service functions were defined and a group of design reference missions were selected which represented needs for each of the service functions. Servicing concepts were developed through mission analysis and STS timeline constraint analysis. The hardware needs for accomplishing the service functions were identified with emphasis being placed on applying equipment in the current NASA inventory and that in advanced stages of planning. A more comprehensive service model was developed based on the NASA and DoD mission models segregated by mission class. The number of service events of each class were estimated based on average revisit and service assumptions. Service Kits were defined as collections of equipment applicable to performing one or more service functions. Preliminary design was carrid out on a selected set of hardware needed for early service missions. The organization and costing of the satellie service systems were addressed.

Source record↗

Design integration and noise studies for jet STOL aircraft. Task 7C: Augmentor wing cruise blowing valveless system. Volume 2: Small-scale development testing of augmentor wing critical ducting components

Augmentor wing ducting system studies conducted on a valveless system configuration that provides cruise thrust from the augmentor nozzles have shown that most of the duct system pressure loss would occur in the strut-wing duct y-junction and the wing duct-augmentor lobe nozzles. These components were selected for development testing over a range of duct Mach numbers and pressure ratios to provide a technical basis for predicting installed wing thrust loading and for evaluating design wing loading of a particular wing aspect ratios. The flow characteristics of ducting components with relatively high pressure loss coefficients were investigated. The turbulent pressure fluctuations associated with flows at high Mach numbers were analyzed to evaluate potential duct fatigue problems.

Runnels, J. N.↗

Efficiency of an AMTEC recirculating test cell, experiments and projections

The alkali metal thermal to electric converter (AMTEC) is an electrochemical device for the direct conversion of heat to electrical energy with efficiencies potentially near Carnot. The future usefulness of AMTEC for space power conversion depends on the efficiency of the devices. Systems studies have projected from 15 to 35 percent thermal to electric conversion efficiencies, and one experiment has demonstrated 19 percent efficiency for a short period of time. Recent experiments in a recirculating test cell (RTC) have demonstrated sustained conversion efficiencies as high as 10.2 percent early in cell life and 9.7 percent after maturity. Extensive thermal and electrochemical analysis of the cell during several experiments demonstrated that the efficiency could be improved in two ways. First, the electrode performance could be improved. The electrode for these tests operated at about one third the power density of state of the art electrodes. The low power density was caused by a combination of high series resistance and high mass flow resistance. Reducing these resistances could improve the efficiency to greater than 10 percent. Second, the cell thermal performance could be improved. Efficiencies greater than 14 percent could be realized through reducing the radiative thermal loss. Further improvements to the efficiency range predicted by systems studies can be accomplished through the development and use of an advanced condenser with improved reflectivity, close to that of a smooth sodium film, and the series connecting of individual cells to further reduce thermal losses.

Underwood, M. L.↗