Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Center for Efficiency in Sustainable Energy Systems

The main goal of the Center for Efficiency in Sustainable Energy Systems is to produce a methodology that evaluates a variety of energy systems. Task I. Improved Energy Efficiency for Industrial Processes: This task, completed in partnership with area manufacturers, analyzes the operation of complex manufacturing facilities to provide flexibilities that allow them to improve active-mode power efficiency, lower standby-mode power consumption, and use low cost energy resources to control energy costs in meeting their economic incentives; (2) Identify devices for the efficient transformation of instantaneous or continuous power to different devices and sections of industrial plants; and (3) use these manufacturing sites to demonstrate and validate general principles of power management. Task II. Analysis of a solid oxide fuel cell operating on landfill gas: This task consists of: (1) analysis of a typical landfill gas; (2) establishment of a comprehensive design of the fuel cell system (including the SOFC stack and BOP), including durability analysis; (3) development of suitable reforming methods and catalysts that are tailored to the specific SOFC system concept; and (4) SOFC stack fabrication with testing to demonstrate the salient operational characteristics of the stack, including an analysis of the overall energy conversion efficiency of the system. Task III. Demonstration of an urban wind turbine system: This task consists of (1) design and construction of two side-by-side wind turbine systems on the YSU campus, integrated through power control systems with grid power; (2) preliminary testing of aerodynamic control effectors (provided by a small business partner) to demonstrate improved power control, and evaluation of the system performance, including economic estimates of viability in an urban environment; and (3) computational analysis of the wind turbine system as an enabling activity for development of smart rotor blades that contain integrated sensor/actuator/controller modules to enhance energy capture and reduce aerodynamic loading and noise by way of virtual aerodynamic shaping. Accomplishments: Task I. Improved Energy Efficiency for Industrial Processes: We organized an energy management training session held on February 22, 2011, which was advertised through a regional manufacturing association to provide wide-ranging notification. Over two dozen companies were represented a the seminar, ranging from heavy manufacturing businesses with $5,000,000 per year energy expenses, to small, light manufacturing facilities. Task 2. Landfill Fuel Cell Power Generation Solid Oxide Fuel Cells (SOFCs) were constructed and evaluated as a means of obtaining electrical energy from landfill gas. Analysis of landfill gas. Attempts at collecting gas samples at the landfill and evaluating them on campus were still unsuccessful. Even a Teflon® sample bag would lose its H2S content. Evaluation of Gas Clean-up We consider this a confirmation of the CO2 effect on the solubility of H2S in water making much less sulfide available for the photocatalyst. It also means that another method should be employed to clean up landfill gas. Nonetheless, composition of impurities in landfill gas was reduced sufficiently to allow successful operation of the test fuel cell. Comparison to a PEM fuel cell system. If a PEMFC were to be operated with landfill gas as the fuel, the gas would have to be treated for sulfur removal, and then processed in a reformer large enough to drive the equilibrium far toward the products, so that negligible CO would flow into the fuel cell. Analysis of a fuel cell running on landfill gas. Using a Gow-Mac gas chromatograph with a thermal conductivity detector, unambiguous determination of CO can be made, at least as a primary constituent Task 3: Task 3 Plasma Controlled Turbine Blades Wind Turbine Selection. After carefully reviewing the various model available in the market the team selected the ARE 110 (2.5kW). The ARE 110 provides a very long life with little maintenance due to their relatively low rotational speeds (low RPM). The turbines large swept area (10.2ms2/110sq.ft), high-efficiency blades, purpose built alternator, and optimized power electronics ensure maximum energy capture from a wide range of wind speeds. Two wind turbines were installed side-by-side at the Melnick Hall site to compare their performance. Evaluate and Optimize Aerodynamically Enhanced Turbine Blades Due to delays in the installation of the wind turbines, no actual data was obtained within the contract period. At this time, the turbines are installed and operational at YSU with standard blades. We are in contact with Orbital Research and in discussion as to how best the required data can be obtained.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Structure and reactive properties of Nb-impregnated two-dimensional pillared MWW zeolites for total oxidation of volatile organic compounds

In this work, the structure and reactive properties of niobium (Nb)-impregnated MWW-type materials were evaluated for gas-phase total oxidation of volatile organic compounds, including BTX (benzene, toluene and o -xylene). The role of the type of structure (two or three-dimensional) and the loading of Nb were considered. The results indicated most Nb species with a tetrahedral coordination on the external surfaces of both two- and three-dimensional zeolites, together with a minimal contribution of octahedral extra-framework Nb 2 O 5 species. The texture and Nb content played a key role in the gas-phase total oxidation of BTX. With the same Nb content (5 wt%), the pillared zeolite exhibited a higher specific surface, larger pore volume and mesopores between the MWW nanosheets when compared to the MCM-22 zeolites, which resulted in high accessibility of the reactant molecules to the active sites, reflected in higher BTX conversion at lower and higher temperatures (50–300 °C). The best performance was achieved with the pillared zeolite (10 wt% Nb), reaching a BTX conversion at 300 °C of 92%, 69% and 58%, respectively. Here, the catalyst was stable for up to 30 h of reaction.

36 MATERIALS SCIENCE↗

Fast preparation of Bi{sub 2}GeO{sub 5} nanoflakes via a microwave-hydrothermal process and enhanced photocatalytic activity after loading with Ag nanoparticles

Highlights: ► Bi{sub 2}GeO{sub 5} nanoflakes were successfully synthesized via a microwave-assisted solution-phase approach. ► Ag nanoparticles were deposited on the Bi{sub 2}GeO{sub 5} nanoflakes by a photoreduction procedure. ► Catalytic activity of the Ag/Bi{sub 2}GeO{sub 5} nanocomposite in the photo-degradation of rhodamine B (RhB) was much higher than that of pure Bi{sub 2}GeO{sub 5}. -- Abstract: In this work, a facile and rapid microwave-assisted hydrothermal route has been developed to prepare Bi{sub 2}GeO{sub 5} nanoflakes. Ag nanoparticles were subsequently deposited on the Bi{sub 2}GeO{sub 5} nanoflakes by a photoreduction procedure. The phases and morphologies of the products were characterized by powder X-ray diffraction (XRD), X-ray photoelectron spectrum (XPS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and UV–vis diffuse reflectance spectroscopy. Photocatalytic experiments indicate that such Ag/Bi{sub 2}GeO{sub 5} nanocomposite possesses higher photocatalytic activity for RhB degradation under UV light irradiation in comparison to pure Bi{sub 2}GeO{sub 5}. The amount of Ag in the nanocomposite affects the catalytic activity, and 3 wt% Ag showed the highest photodegradation efficiency. Moreover, the catalyst remains active after four consecutive tests. The present study provides a new strategy to design composite materials with enhanced photocatalytic activity.

36 MATERIALS SCIENCE↗

Modeling Nanoscale Ohmics in Carbon Supports of Fuel Cell Cathodes

Here, reducing platinum (Pt) loading in polymer electrolyte fuel cells (PEFCs) while meeting performace requirements is critical to their widespread deployment. However, significant polarization losses manifest at higher current densities in cathodes with lower Pt content. The morphology of the carbon supports in PEFC cathodes affects the location of Pt deposition into the micropits or onto the surface of the carbon support, translating into different kinetic and transport resistances. In this work, we derive an agglomerate scale model that differentiates the sink terms for Pt on the surface and in the pits of carbon supports. We develop an approach to assess the impact of nanoscale ohmic resistance to Pt in the micropits arising from weakly ionic solution in the carbon support on PEFC performance. Effectiveness factors relating the actual reaction rate to the maximum reaction rate (had all the Pt been exposed) are derived and embedded into a one-dimensional catalyst layer model. Parameters in the catalyst layer model are tuned based on experimental local oxygen transport resistances. Subsequently, we estimate bounds for the micropore resistances based on geometric and physical arguments. Lastly, polarization curves are simulated to assess the effect of the micropore resistance in fully-humidified and oxygen-rich environments.

25 ENERGY STORAGE↗

Experimental Investigation on the Performance Loss of Cross-Linked Polymers During Photo-Oxidative Aging

Abstract Polymeric substances have seen an unprecedented integration in countless applications and fields of life, subjecting them to a broad range of environmental conditions, which can cause a form of damage to the structural and mechanical properties of these components known as aging. In this study we investigate the effects of the degradation of polymeric materials due to the extended exposure to sunlight, which can be simulated through controlled photo-oxidative aging using ultraviolet (UV) radiation as the main catalyst of this phenomenon. The effects on mechanical behavior and chemical properties of four polymeric materials with different mechanical characteristics was accordingly monitored throughout the study. The materials range in hardness with the polyurethane adhesive being the hardest and acting plastically, followed by an acrylic which exhibits greater hardening with time, a polyurethane sealant, which behaves in an elastomeric manner, and a silicon sealant, which is the softest of the set. Samples were prepared and subjected to UV radiation at three different temperatures namely 45, 60 and 80°C, for different aging periods ranging from 1 day for higher temperatures to 150 days for lower ones. The samples were then subjected to the Fourier transform Infrared spectroscopy (FTIR) test to monitor the change in the chemical composition of the materials along the aging durations and conditions. The materials were then subjected to mechanical testing along two modes of mechanical loading, which are a simple tension until failure and a double-cyclic test with progressively increasing strain limits after every two successful cycles until the sample reaches failure. The samples are loaded at constant strain rates throughout both tests. These tests revealed the change of behavior of our materials along the aging periods and conditions. The changes in mechanical behavior vary across each individual material depending on the aging temperature and period, with the changes ranging from hardening to softening, embrittlement or an increase in the maximum strain the material can endure before failure. A general trend would be that most materials become harder after photo-oxidation, however due to the range of temperatures in the aging conditions, thermo-oxidation, which causes softening in some of the polymers, has an increasingly notable effect at higher temperatures. A visible correlation can be noted between the change in mechanical behavior and a change in absorbance of Infrared Radiation (IR) in the FTIR spectrum, as the greater the crosslinking throughout the polymer matrix, the lower the absorbance of IR radiation due to the increased stiffness of the overall macro-molecular structure.

Korayem, Abd-Elrahman↗

Importance of Surface IrO x in Stabilizing RuO 2 for Oxygen Evolution

The high precious metal loading and high overpotential of the oxygen evolution reaction (OER) prevents the widespread utilization of polymer electrolyte membrane (PEM) water electrolyzers. In this paper, we explore the OER activity and stability in acidic electrolyte of a combined IrO x /RuO 2 system consisting of RuO 2 thin films with submonolayer (1, 2, and 4 Å) amounts of IrO x deposited on top. Operando extended X-ray absorption fine structure (EXAFS) on the Ir L-3 edge revealed a rutile type IrO 2 structure with some Ir sites occupied by Ru, IrO x being at the surface of the RuO 2 thin film. We monitor corrosion on IrO x /RuO 2 thin films by combining electrochemical quartz crystal microbalance (EQCM) with inductively coupled mass spectrometry (ICP-MS). We elucidate the importance of submonolayer surface IrO x in minimizing Ru dissolution. Finally, our work shows that we can tune the surface properties of active OER catalysts, such as RuO 2 , aiming to achieve higher electrocatalytic stability in PEM electrolyzers.

36 MATERIALS SCIENCE↗

Optical and Probe Diagnostics Applied to Reacting Flows

We plan to explore three major threads during the fellowship period. The first interrogates the flame synthesis of carbon nanotubes using aerosol catalysts. Laser light scattering will reveal changes in particle size at various heights above the burner. Analysis of the flame gas by mass spectroscopy will reveal the chemical composition of the mixture. Finally, absorption measurements will map the nanotube concentration within the flow. The second thread explores soot oxidation kinetics. Cavity ring-down absorption measurements of the carbonaceous aerosol can provide a measure of the mass concentration with time and, hence, an oxidation rate. Spectroscopic and direct probe measurements will provide the temperature of the system needed for subsequent modeling. The third thread will explore the details of turbulent flame dynamics. Laser induced incandescence will be applied to measurements of soot volume fraction in a 2-d configuration. Analysis of seed tracer particles by planar laser light MIE scattering will reveal the elemental fuel mixture fraction in the flames. Cavity ring-down spectroscopy, a pulsed transient absorption method, will determine the instantaneous mass loading and its fluctuation. Finally, fluorescence measurements will investigate the formation of PAH's in these flames.

Ticich, Thomas M.↗

Influence of synthesis conditions and mesoporous structures on the gold nanoparticles supported on mesoporous silica hosts

Loading gold on mesoporous materials via different methods has been actively attempted in the literature, but the knowledge about the influences of synthesis details and different mesoporous structures on the size and thermal stability of gold nanoparticles supported on mesoporous hosts is still limited. In this study, Au/HMS, Au/MCM-41, Au/MCM-48, Au/SBA-15, and Au/SBA-16 samples were prepared by modifying a variety of mesoporous silicas by amine ligands followed by loading HAuCl4 and calcination. The influences of different amine ligands ((3-aminopropyl)triethoxysilane versus N-[3-(trimethoxysilyl)propyl]ethylenediamine), solvents (water versus ethanol), calcination temperatures (200 or 550 C), and mesoporous structures on the size of supported gold nanoparticles were systematically investigated employing nitrogen adsorption-desorption measurement, X-ray diffraction (XRD), diffuse reflectance UV-vis spectroscopy, and transmission electron microscopy (TEM). Interestingly, while big and irregular gold particles situate on MCM-48 with bicontinuous three-dimensional pore structure and relatively small pore size (2.4 nm) upon calcination at 550 C, homogeneous and small gold nanoparticles maintain inside SBA-15 with one-dimensional pore structure and relatively big pore size (6.8 nm). Apparently, the pore structure and pore size of mesoporous silica hosts play a key role in determining the size and thermal stability of the supported gold nanoparticles. Our results may provide some useful clues for the rational design of supported metal catalysts by choosing suitable mesoporous hosts.

36 MATERIALS SCIENCE↗

Computational and Experimental Mechanistic Insights into the Ethanol-to-Butanol Upgrading Reaction over MgO

The mechanism of ethanol upgrading to higher products is still under debate, especially regarding intermediate species and hydrogenation and dehydrogenation steps. In this work, we conducted a combined theoretical and experimental approach to contribute to this discussion. For such, detailed electronic structure density functional theory calculations (aiming at probing density of states, infrared spectra, geometric parameters, charge densities, and reaction energetics) and diffuse reflectance infrared Fourier transform spectroscopy experiments were carried out revealing the relevance of an appropriate combination of reactive surface sites to support the formation of several intermediates that are formed in the C-C coupling over MgO. The roles of Mg and O sites were also studied under an electronic perspective and different geometrical arrangements. We found that a kink configuration was the most adequate for ethanol to 1-butanol upgrading. Our calculations also gave us arguments to propose distinct reaction routes, whose mutual predominance would depend upon reaction temperature. At temperatures up to 573 K, the so-called β-route, which goes through scission of a Cβ-H bond and formation of an oxametallacycle-like intermediate, would dominate the coupling, whereas at higher temperatures, up to 673 K, a more usual Guerbet mechanism, via an aldol coupling step and then consecutive hydrogenations, would be expected. Here, the theoretical conclusions were followed by a careful experimental strategy using sequential experimental planning techniques in order to estimate accurate parameters with the lowest possible experimental load. Information from these different sources were coupled to develop a mathematical model for the rate of the ethanol upgrading reaction, using a Langmuir-Hinshelwood-Hougen-Watson approach. The developed and statistically validated model adequately described the experimental data at 673 K and 1.1 bar total pressure for ethanol partial pressures in the range from 0 to 20 kPa.

09 BIOMASS FUELS↗

How to stabilize highly active Cu + cations in a mixed-oxide catalyst

Mixed-metal oxides exhibit novel properties that are not present in their isolated constituent metal oxides and play a significant role in heterogeneous catalysis. In this study, a titanium-copper mixed-oxide (TiCuO x ) film has been synthesized on Cu(111) and characterized by complementary experimental and theoretical methods. At sub-monolayer coverages of titanium, a Cu 2 O-like phase coexists with TiCuO x and TiO x domains. When the mixed-oxide surface is exposed at elevated temperatures (600–650 K) to oxygen, the formation of a well-ordered TiCuO x film occurs. Stepwise oxidation of TiCuO x shows that the formation of the mixed-oxide is faster than that of pure Cu 2 O. As the Ti coverage increases, Ti-rich islands (TiO x ) form. The adsorption of CO has been used to probe the exposed surface sites on the TiO x –CuO x system, indicating the existence of a new Cu + adsorption site that is not present on Cu 2 O/Cu(111). Adsorption of CO on Cu + sites of TiCuO x is thermally more stable than on Cu(111), Cu 2 O/Cu(111) or TiO 2 (110). The Cu + sites in TiCuO x domains are stable under both reducing and oxidizing conditions whereas the Cu 2 O domains present on sub-monolayer loads of Ti can be reduced or oxidized under mild conditions. Furthermore, the results presented here demonstrate novel properties of TiCuO x films, which are not present on Cu(111), Cu 2 O/Cu(111), or TiO 2 (110), and highlight the importance of the preparation and characterization of well-defined mixed-metal oxides in order to understand fundamental processes that could guide the design of new materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanoparticle O–H Bond Dissociation Free Energies from Equilibrium Measurements of Cerium Oxide Colloids

A novel equilibrium strategy for measuring the hydrogen atom affinity of colloidal metal oxide nanoparticles is presented. Reactions between oleate-capped cerium oxide nanoparticle colloids (nanoceria) and organic proton-coupled electron transfer (PCET) reagents are used as a model system. Nanoceria redox changes, or hydrogen loadings, and overall reaction stoichiometries were followed by both 1 H NMR and X-ray absorption near-edge spectroscopies. Furthermore, these investigations revealed that, in many cases, reactions between nanoceria and PCET reagents reach equilibrium states with good mass balance. Each equilibrium state is a direct measure of the bond strength, or bond dissociation free energy (BDFE), between nanoceria and hydrogen. Further studies, including those with larger nanoceria, indicated that the relevant bond is a surface O–H. Thus, we have measured surface O–H BDFEs for nanoceria—the first experimental BDFEs for any nanoscale metal oxide. Remarkably, the measured CeO–H BDFEs span 13 kcal mol –1 (0.56 eV) with changes in the average redox state of the nanoceria colloid. Possible chemical models for this strong dependence are discussed. We propose that the tunability of ceria BDFEs may be important in explaining its effectiveness in catalysis. More generally, metal oxide BDFEs have been used as predictors of catalyst efficacy that, traditionally, have only been accessible by computational methods. These results provide important experimental benchmarks for metal oxide BDFEs and demonstrate that the concepts of molecular bond strength thermochemistry can be applied to nanoscale materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Construction of CQDs-Bi{sub 20}TiO{sub 32}/PAN electrospun fiber membranes and their photocatalytic activity for isoproturon degradation under visible light

Highlights: • The flexible fiber membranes were prepared by coaxial electrospinning technique. • CQDs-Bi{sub 20}TiO{sub 32} photocatalyst was uniformly fixed on the surfaces of PAN fibers. • The fiber membranes had high photocatalytic activity for degradation of isoproturon. • The composite fiber membranes exhibited good recyclability. - Abstract: The CQDs-Bi{sub 20}TiO{sub 32} photocatalysts exhibited high visible-light responsive photocatalytic activity. To achieve the cyclic utilization of CQDs-Bi{sub 20}TiO{sub 32}, the novel flexible CQDs-Bi{sub 20}TiO{sub 32}/PAN fiber membranes were prepared by a simple coaxial electrospinning technique. It was found that the CQDs-Bi{sub 20}TiO{sub 32} photocatalyst could be firmly and uniformly fixed on the surfaces of electrospun fibers and the composite fiber membranes possessed the hierarchical macro- and mesoporous structure. The loaded CQDs-Bi{sub 20}TiO{sub 32} endowed the composite fiber with an obvious photocatalytic activity for the degradation of the herbicide isoproturon under visible light irradiation. Among these samples, S3 at photocatalyst dosage 15 w/v% had the highest degradation efficiency for isoproturon. Meanwhile, the core-shell structured inorganic-organic hybrid fiber membranes have a significant advantage in the recyclability for photocatalyts. The flexible CQDs-Bi{sub 20}TiO{sub 32}/PAN electrospun fiber membranes would have potential applications in efficient removal of organic contaminants.

36 MATERIALS SCIENCE↗

Dynamic Bottlebrush Polymer Networks: Self-Healing in Super-Soft Materials

Here, we introduce a design strategy to expand the range of accessible mechanical properties in covalent adaptable networks (CANs) using bottlebrush polymer building blocks. Well-defined bottlebrush polymers with rubbery poly(4-methylcaprolactone) side-chains were crosslinked in formulations that include a bislactone and strong Lewis acid (tin ethylhexanoate). The resulting materials exhibit tunable stress relaxation rates at elevated temperatures (160–180 °C) due to dynamic ester crosslinks that undergo transesterification with residual hydroxy groups. Varying the crosslinker loading or bottlebrush backbone degree of polymerization yields predictable low-frequency shear moduli ca. 10–100 kPa, well below values typical of linear polymer CANs (1 MPa). These extensible networks can be stretched to strains as large as 350% before failure and undergo efficient self-healing to recover >85% of their original toughness upon repeated fracture and melt processing. In summary, molecular architecture creates new opportunities to tailor the mechanical properties of CANs in ways that are otherwise difficult to achieve.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nature of molybdenum carbide surfaces for catalytic hydrogen dissociation using machine-learned potentials: an ensemble-averaged perspective

Molybdenum carbides with an electronic structure similar to noble metals have gained attention as a promising low-cost catalyst for biomass valorization and the hydrogen evolution reaction. However, our fundamental understanding of the catalyst surface and how different phases of these catalysts behave at varying reaction conditions is limited to ground state density functional theory calculations as ab initio molecular dynamics (AIMD) is computationally prohibitive at relevant length and time scales. Here, in this work, we train a multi-atomic cluster expansion (MACE) machine-learned interatomic potentials (MLIP) to study hydrogen dissociation and dynamics over Mo, δ-MoC, α-Mo 2 C, and β-Mo 2 C surfaces at varying temperatures and hydrogen partial pressures. Our simulations identify unique and different molecular and atomic hydrogen adsorption sites on different surfaces that do not depend on the temperature. At low hydrogen pressures, the surface coverage is monolayer, which transitions to two-layer adsorption at higher pressures. We find that atomic hydrogen diffusion and recombinations are preferred over molybdenum atom hollow sites, while the diffusion over carbon-terminated facets was negligible, signifying particularly strong C–H interactions. In contrast, molecular hydrogen adsorption occurs mostly atop Mo or the bridging sites. At a comparable hydrogen loading, β-Mo 2 C (001) is the most active surface for hydrogen dissociation reaction. This work provides insights into the dynamic nature of the hydrogen dissociation chemistry and the diversity of hydrogen adsorption sites on molybdenum carbides.

08 HYDROGEN↗

Methanol Partial Oxidation on Cu(111) and PtCu(111) Single-Atom Alloy Surfaces: Effect of Surface Oxygen Coverage on Selectivity

The selective oxidation of methanol to formaldehyde on Cu surfaces is an important and well-studied reaction. However, a systematic analysis of product selectivity as a function of oxygen coverage on Cu(111) and Cu-based single-atom alloys (SAAs) has not been previously reported. In this work, we present a comprehensive investigation of deuterated methanol (CD 3 OH) partial oxidation on Cu(111) and 1% PtCu(111) SAA surfaces as a function of preadsorbed oxygen coverage. Temperature-programmed desorption (TPD) and X-ray photoelectron spectroscopy (XPS) reveal that isolated Pt atoms inhibit the initial surface oxidation of Cu(111) under low oxygen exposures. Despite this difference in oxidation kinetics, the product selectivity remains largely unaffected: on both Cu(111) and PtCu(111), formaldehyde (CD 2 O) is the predominant partial oxidation product over a broad range of oxygen coverages. The selectivity toward formaldehyde peaks at intermediate oxygen coverages (∼0.3 monolayers, ML), indicating the existence of an optimal oxygen loading for partial oxidation. Notably, the similar product selectivities on Cu(111) and PtCu(111) over a range of surface oxygen coverage indicate that Pt single atoms do not significantly alter the reaction pathway or shift the optimal oxygen coverage for formaldehyde formation. Control experiments confirm that Cu(111) is unreactive toward methanol in the absence of oxygen, while PtCu(111) surfaces produce a small amount of formaldehyde even when oxygen is not preadsorbed, indicating that isolated Pt atoms facilitate O−H activation at below 150 K, leading to H 2 desorption, followed by C−D activation at higher temperatures (∼350 K). Density functional theory (DFT)-based calculations show that Pt atoms increase the O 2 dissociation barrier relative to Cu(111), consistent with the observed inhibition of oxidation at low exposures. Overall, this work provides the first detailed selectivity map for methanol oxidation on oxidized Cu(111) and PtCu(111) SAA surfaces. By linking classical mechanistic insights such as methoxy- and formate-mediated pathways with single-atom alloy catalyst design, this work demonstrates that while Pt substitution modulates the oxidation kinetics and oxygen binding, the overall selectivity toward formaldehyde is governed primarily by oxygen coverage. These findings underscore the potential of isolated dopants to tune surface oxidation behavior without compromising the intrinsic partial oxidation selectivity of copper-based catalysts.

36 MATERIALS SCIENCE↗

Heterogenous catalysis for oxygen tolerant photoredox atom transfer radical polymerization and small-molecule dehalogenation

Heterogeneous photocatalysts (PCs) have garnered attention for their sustainability and cost-effectiveness. Despite the existence of various types of these PCs, their synthesis often involves complex, multi-step procedures and laborious purification. Herein, we propose a simple method for attaching small-molecule photocatalytic species onto crosslinked 3-D polymer networks as insoluble scaffolds to create robust heterogeneous PCs. The highly swellable poly(ethylene glycol)-based ChemMatrix (CM) resin, known for its amphiphilic properties and high functional group loading, facilitated the covalent immobilization of the photoredox dye Eosin Y (EY), but also streamlined functionalization with Ir( III ) complexes. The resulting heterogeneous CM-EY demonstrated efficient photocatalytic performance in open-to-air dual photoredox catalysis of atom transfer radical polymerization (photo-ATRP) under green light. This was confirmed by the well-controlled synthesis of polymers with molecular masses ranging from 20 kDa to 300 kDa and low dispersities. Furthermore, CM-EY exhibited excellent photostability and recyclability over multiple cycles of ATRP. The heterogeneous catalysis of photo-ATRP provided high temporal control and enabled benign conditions for synthesizing protein-polymer hybrids (PPH). When combined with the initiator-modified CM (CM-BIB), CM-EY facilitated the solid-phase synthesis of homopolymers and block copolymers with recyclable performance. However, the coordinatively bound Ir@CM showed decreased catalytic activity and efficiency toward photoredox dehalogenation due to the leaching of active species during recycling. This study highlights the advantages of the covalent linking of catalysts to solid supports over non-covalent interactions, underscoring the potential of functionalized polymer resin as a promising scaffold. Such an approach offers customization and tunability, presenting opportunities for innovation in green chemistry.

Kapil, Kriti↗

Nanocolumnar Pt:Ni Alloy Thin Films by High Pressure Sputtering for Oxygen Reduction Reaction

Self-supported nanocolumnar Pt:Ni thin films (TFs) with varying Pt:Ni atomic ratios and Pt mass loadings were produced on a microporous layer (MPL)-like surface composed of carbon particles by high pressure sputtering and examined as oxygen reduction reaction (ORR) electrocatalysts for polymer electrolyte membrane fuel cells. Cauliflower-like microstructures were observed from scanning electron microscopy imaging. Various Pt:Ni atomic ratios were obtained by simply changing the relative deposition power between Pt and Ni source and investigated by X-ray diffraction and quartz crystal microbalance analysis. Additionally, electrochemical characterization of the Pt:Ni-TF/MPL-like-layer/glassy-carbon samples was conducted through benchtop cyclic voltammetry and rotating disk electrode measurements. The electrochemically active surface area (ECSA) was found to be between 22–42 m 2 g -1 for different Pt:Ni atomic ratios. Lower Pt mass loadings exhibited a higher ECSA and the catalytic activity of all Pt:Ni ratios increased with the increase in Pt mass loading. The ORR activity of the Pt:Ni-TFs increased in the order of 3:1 < 1:1 < 1:3 with exhibiting a specific activity of 1781 μA cm -2 and mass activity of 0.66 A mg -1 for the Ni-rich film with 1:3 ratio. The catalytic performance of Pt:Ni-TFs were higher than traditional high surface area carbon supported Pt nanoparticles, elemental Pt nanorods, and Pt-Ni nanorods.

08 HYDROGEN↗

Dissolved carbonic anhydrase for enhancing post-combustion carbon dioxide hydration in aqueous ammonia

Aqueous ammonia solvents that capture CO2 as ionic complexes of carbonates with ammonium have recently been advanced as alternatives to amine-based solvents due to their lower energy requirements for thermal regeneration. In ammonia based solvents, the hydration of CO2 to form bicarbonate may become a rate-limiting step as the CO2 loading increases and the resulting pH level of the solvent decreases. Variants of the enzyme carbonic anhydrase can accelerate the reversible hydration of CO2 to yield bicarbonate by more than 10(6)-fold. The possible benefit of bovine carbonic anhydrase (BCA) addition to solutions of aqueous ammonia to enhance CO2 hydration was investigated in semi-batch reactions within continuously stirred tank reactors or in a bubble column gas-liquid contactor. Adding 154 mg/liter of BCA to 2 M aqueous ammonia provided a 34.1% overall increase in the rate of CO2 hydration (as indicated by the production of [H+]) as the pH declined from 9.6 to 8.6 during sparging with a 15% CO2, 85% N-2 gas at a flow rate of 3 lpm. The benefits of adding BCA to enhance CO2 hydration were only discernable below similar to pH 9. The implications of the apparent pH limitations on the utility of BCA are discussed in the context of absorber unit operation design. Possible embodiments of carbonic anhydrase as either an immobilized catalyst or as a dissolved, recirculating catalyst in potential plant scale aqueous ammonia systems are considered as well. (C) 2010 Published by Elsevier Ltd.

59 BASIC BIOLOGICAL SCIENCES↗