Search NASA⌕ Search

SEARCH · Search NASA

Results for “vortex”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Vortex shedding from a blunt trailing edge with equal and unequal external mean velocities

A flow visualization study showed that strong Karman vortices are developed behind the blunt trailing edge of a plate when the free stream velocities over both surfaces are equal. These vortices tend to disappear when the surface velocities are unequal. This observation provided an explanation for the occurrence and disappearance of the lip noise often present in coaxial jets. Vortex formation and lip noise occurred at a Strouhal number of about 0.2 based on the lip thickness and the average of the external steady-state velocities. Results from theoretical calculations of the vortex formation, based on an inviscid, incompressible analysis of the motion of point vortices, were in good agreement with the experimental observations.

Brinich, P. F.↗
NASA NTRS1975

Effects of spanwise blowing on the pressure field and vortex-lift characteristics of a 44 deg swept trapezoidal wing

Wind-tunnel data were obtained at a free-stream Mach number of 0.26 for a range of model angle of attack, jet thrust coefficient, and jet location. Results of this study show that the sectional effects to spanwise blowing are strongly dependent on angle of attack, jet thrust coefficient, and span location; the largest effects occur at the highest angles of attack and thrust coefficients and on the inboard portion of the wing. Full vortex lift was achieved at the inboard span station with a small blowing rate, but successively higher blowing rates were necessary to achieve full vortex lift at increased span distances. It is shown that spanwise blowing increases lift throughout the angle-of-attack range, delays wing stall to higher angles of attack, and improves the induced-drag polars. The leading-edge suction analogy can be used to estimate the section and total lifts resulting from spanwise blowing.

Campbell, J. F.↗
NASA NTRS1975

A static air flow visualization method to obtain a time history of the lift-induced vortex and circulation

A recently proposed method of flow visualization was investigated at the National Aeronautics and Space Administration's Langley Research Center. This method of flow visualization is particularly applicable to the study of lift-induced wing tip vortices through which it is possible to record the entire life span of the vortex. To accomplish this, a vertical screen of smoke was produced perpendicular to the flight path and allowed to become stationary. A model was then driven through the screen of smoke producing the circular vortex motion made visible as the smoke was induced along the path taken by the flow and was recorded by highspeed motion pictures.

Patterson, J. C., Jr.↗
NASA NTRS1975

A Three-Dimensional Solution of Flows over Wings with Leading-Edge Vortex Separation. Part 1: Engineering Document

A method of predicting forces, moments, and detailed surface pressures on thin, sharp-edged wings with leading-edge vortex separation in incompressible flow is presented. The method employs an inviscid flow model in which the wing and the rolled-up vortex sheets are represented by piecewise, continuous quadratic doublet sheet distributions. The Kutta condition is imposed on all wing edges. Computed results are compared with experimental data and with the predictions of the leading-edge suction analogy for a selected number of wing planforms over a wide range of angle of attack. These comparisons show the method to be very promising, capable of producing not only force predictions, but also accurate predictions of detailed surface pressure distributions, loads, and moments.

Brune, G. W.↗
NASA NTRS1975

Prediction of vortex flow characteristics of wings at subsonic and supersonic speeds

The leading-edge-suction analogy of Polhamus, which has been successful in the prediction of vortex lift characteristics on wings with pointed tips at subsonic and supersonic speeds, has recently been extended to account for the vortex flow characteristics for wings with side edges. Comparisons of experimental data and other currently used methods with the extended method are made for wings having side edges at subsonic and supersonic speeds. Recent data obtained for a low-aspect-ratio cropped-delta wing with various amounts of asymmetrical tip rake, simulating a roll control device, are also presented.

Lamar, J. E.↗
NASA NTRS1975

Simulation by vortex rings of the unsteady pressure field near a jet

A coordinated theoretical and experimental program has been undertaken to construct a model for the shedding of vortex rings in order to simulate the real-time pressure variation in the acoustic region near the jet. The basic parameters in the analytic solutions are the eddy viscosity coefficient and the time intervals between successive shedding of vortex rings from the nozzle lip. The experimental and theoretical results show good qualitative agreement.

Liu, C. H.↗
NASA NTRS1975

A three-dimensional solution of flows over wings with leading-edge vortex separation

The application of a new, general, potential flow computational technique to the solution of the subsonic, three-dimensional flow over wings with leading-edge vortex separation is presented. The present method is capable of predicting forces, moments, and detailed surface pressures on thin, sharp-edged wings of rather arbitrary planform. The wing geometry is arbitrary in the sense that leading and trailing edges may be curved or kinked and the wing may have arbitrary camber and twist. The method employs an inviscid flow model in which the wing, the rolled-up vortex sheets, and the wake are represented by piecewise continuous quadratic doublet sheet distributions. The Kutta condition is imposed along all wing edges. Strengths of the doublet distributions as well as shape and position of the free fortex sheet spirals are computed in iterative fashion starting with an assumed initial sheet geometry. The method is verified by numerous computed results.

Weber, J. A.↗
NASA NTRS1977

Trimmed noncoplanar planforms with minimum vortex drag

Vortex-lattice subsonic method determines mean camber surface for trimmed noncoplanar planforms with minimum vortex drag. Multiple surfaces can be designed together to yield trimmed configuration with minimum induced drag at some specified lift coefficient. Program is applicable to isolated wings, wing-canard configuration, tandem wing, and wing-winglet configuration.

Lamar, J. E.↗
NASA NTRS1975

Design and preliminary tests of a blade tip air mass injection system for vortex modification and possible noise reduction on a full-scale helicopter rotor

Full-scale tests were conducted on the Langley helicopter rotor test facility as part of a study to evaluate the effectiveness of a turbulent blade tip air mass injection system in alleviating the impulsive noise (blade slap) caused by blade-vortex interaction. Although blade-slap conditions could not be induced during these tests, qualitative results from flow visualization studies using smoke showed that the differential velocity between the jet velocity and the rotor tip speed was a primary parameter controlling the vortex modification.

Pegg, R. J.↗
NASA NTRS1976

Vortex maneuver lift for super-cruise configurations

Some of the theoretical and experimental research conducted at the NASA Langley Research Center is presented to investigate the subsonic vortex-lift producing capabilities for two classes of Super-Cruise designs: a close-coupled wing-canard arrangement and a slender wing configuration. In addition, several analytical methods are discussed for estimating critical structural design loads for thin, highly swept wings having separated leading-edge vortex flows.

Campbell, J. F.↗
NASA NTRS1976

Applications of vortex lattice theory to preliminary aerodynamic design

Some applications of the vortex-lattice theory to the preliminary aerodynamic design and analysis of subsonic aircraft were presented. These methods include the Rockwell-Tulinius vortex-lattice theory for estimating aerodynamic characteristics, a Trefftz plane optimization procedure for determining the span loads for minimum induced drag, and a modification of the Trefftz plane procedure to estimate the induced drag for specified span loads. The first two methods are used to aerodynamically design aircraft planforms, twists, and cambers, and the latter method is used to estimate the drag for components such as flaps and control surfaces. Results from the theories for predicting lift and pitching moment, drag due to lift, and the drag of control surfaces are compared with experimental data. This data was obtained on a general aviation model with flaps and a close-coupled canard-wing model.

Paulson, J. W., Jr.↗
NASA NTRS1976

New convergence criteria for the vortex-lattice models of the leading-edge separation

The convergence criterion for the vortex-lattice technique which deals with delta wings exhibiting significant leading-edge separation was studied. It was shown that one can predict pressure distributions without irregularities which agree fairly well with experimental data (which show some irregularities of their own) by replacing the system of discrete vortex lines with a single concentrated core. This core has a circulation equal to the algebraic sum of the circulations around the discrete lines and is located at the centroid of these lines. Moreover, there is a requirement that the position and strength of the core must converge as the number of elements increases. Because the calculation of the position and strength of the core is much less involved than the calculation of the loads, this approach has the additional desirable feature of requiring less computational time.

Kandil, O. A.↗
NASA NTRS1976

Arrangement of vortex lattices

A new method is developed for solving the lifting-surface equation for thin wings. The solution requires the downwash equation to be in the form of Cauchy integrals which can be interpreted as a vortex lattice with the positions of the vortices and control points dictated by the finite sum used to approximate the integrals involved. Lan's continuous loading method is employed for the chordwise integral since it properly accounts for the leading-edge singularity, Cauchy singularity, and Kutta condition. Unlike Lan, the spanwise loading is also continuous and the Cauchy singularity in the spanwise integral is also properly accounted for by using the midpoint trapezoidal rule and the theory of Chebyshev polynomials. This technique yields the exact classical solution to Prandtl's lifting-line equation.The solution to the lifting-surface equation for rectangular wings was found to compare well with other continuous loading methods, but with much smaller computational times, and to converge faster than other vortex lattice methods.

Dejarnette, F. R.↗
NASA NTRS1976

Wake vortex encounter hazards criteria for two aircraft classes

An investigation was conducted using a piloted, motion-base simulator to determine wake vortex hazard criteria for two classes of jet transport aircraft. A light business jet and a large multiengine jet transport were represented respectively. The hazard boundaries were determined in terms of the maximum bank angle due to the vortex encounter. Upsets as small as 7 deg in bank angle were considered to be hazardous at breakout altitude (200 ft (61.0 m)) for Instrument Flight Rule (IFR) and at 50 ft (15.2 m) for Visual Flight Rule (VFR) for both aircraft classes. Proximity to the ground was the primary reason for a hazardous rating. This was reflected in the reduction in the maximum bank angle at the hazard boundary and in more consistent ratings as altitude was decreased.

Sammonds, R. I.↗
NASA NTRS1975

Laser velocimeter measurements of rotor blade loads and tip vortex rollup

A method for obtaining and analyzing the instantaneous velocities of helicopter rotor flow fields through use of a laser velocimeter capable of simultaneously sensing two components of velocity is described. Rotor blade aerodynamic loads may be computed from the velocity distributions near the blades. The experiment was conducted with a 2.13 m (7 ft) diameter model helicopter rotor operating in a wind tunnel. Velocity distributions are presented which document the flow field near the advancing blade. Circulation is calculated from the velocity measurements, and the radial distribution of circulation is discussed. The influence of the tip vortex from the preceding blade is apparent in this distribution. Tip vortex rollup on the advancing blade was documented by making a series of measurements at various distances behind the blade. Effects of blade drag are evident in the velocities behind the blade trailing edge.

Biggers, J. C.↗
NASA NTRS1976

Flight investigation of the response of a helicopter to the trailing vortex of a fixed-wing aircraft

A flight investigation was conducted to quantitatively determine the response of a medium-weight helicopter to the trailing-vortex system of a fixed-wing aircraft. Flight tests and analytical tools were both utilized in the investigation. The flight tests involved an extensively instrumented UH-1H helicopter and a C-54 aircraft. Penetrations of the vortex system by the UH-1H were made at the following nominal conditions: the C-54 flew at 5500 feet altitude at a nominal gross weight of 58,000 pounds and an indicated airspeed of 115 knots in a cruise configuration. The UH-1H, nominally 7200 pounds gross weight, flew at 60 knots indicated airspeed during the penetrations at separation distances of 6.64 nautical miles to 0.42 nautical mile between aircraft. In general, the data analyzed for the above tests indicated that no unsafe penetration occurred. Further, penetrating vehicle attitude changes and structural loads were nominal. In addition, the response of the helicopter did not change appreciably with decreased separation distance.

Mantay, W. R.↗
NASA NTRS1976

Hazard criteria for wake vortex encounters

Piloted six-degrees-of-freedom motion simulator investigations were conducted at the NASA Ames Research Center to determine criteria relating the hazard posed by a wake vortex encounter to the response of the encountering airplane. These investigations demonstrated that wake vortex encounters can be realistically reproduced on a simulator, established that the maximum bank angle due to the encounter provides the best correlation with the pilot's subjective assessment of the hazard, and determined hazard boundaries in terms of maximum bank angle for two classes of jet transport aircraft.

Sammonds, R. I.↗
NASA NTRS1976

Vortex shedding from a blunt trailing edge with equal and unequal external mean velocities

A flow-visualization study has shown that strong Karman vortices develop behind the blunt trailing edge of a plate when the free-stream velocities over both surfaces are equal and that the vortices tend to disappear when the surface velocities are unequal. This observation provides an explanation for the occurence and disappearance of certain discrete tones often found to be present in the noise spectra of coaxial jets. Both the vortex formation and the tones occur at a Strouhal number based on the lip thickness and the average of the external steady-state velocities of about 0.2. Results from theoretical calculations of the vortex formation, based on an inviscid incompressible analysis of the motion of point vortices, were in good agreement with the experimental observations.

Boldman, D. R.↗