Search NASA⌕ Search

SEARCH · Search NASA

Results for “BURNING PROCESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

High-temperature processing of cuprate oxide superconductors

Superconducting Y1Ba2Cu3O7 ('123') films were fabricated on the Y2BaCuO5 ('211') phase substrate. The superconducting characteristics of these films, in terms of superconducting transition temperature (Tc) and width, are better than those using other oxide compounds as substrates. In addition, using high-temperature processing, the bulk 211 phase was converted into the 123 phase. A new high Tc copper oxide material with non-rare-earth elements (Bi-Sr-Cu-O) was prepared using similar high-temperature processing. High-temperature processing presents an alternative synthetic route in the search of new high Tc superconductors.

Wu, M. K.↗

Fabrication of Composite Combustion Chamber/Nozzle for Fastrac Engine

The Fastrac Engine developed by the Marshall Space Flight Center for the X-34 vehicle began as a low cost engine development program for a small booster system. One of the key components to reducing the engine cost was the development of an inexpensive combustion chamber/nozzle. Fabrication of a regeneratively cooled thrust chamber and nozzle was considered too expensive and time consuming. In looking for an alternate design concept, the Space Shuttle's Reusable Solid Rocket Motor Project provided an extensive background with ablative composite materials in a combustion environment. An integral combustion chamber/nozzle was designed and fabricated with a silica/phenolic ablative liner and a carbon/epoxy structural overwrap. This paper describes the fabrication process and developmental hurdles overcome for the Fastrac engine one-piece composite combustion chamber/nozzle.

Lawerence, T.↗

Fabrication of Composite Combustion Chamber/Nozzle for Fastrac Engine

The Fastrac Engine developed by the Marshall Space Flight Center for the X-34 vehicle began as a low cost engine development program for a small booster system. One of the key components to reducing the engine cost was the development of an inexpensive combustion chamber/nozzle. Fabrication of a regeneratively cooled thrust chamber and nozzle was considered too expensive and time consuming. In looking for an alternate design concept, the Space Shuttle's Reusable Solid Rocket Motor Project provided an extensive background with ablative composite materials in a combustion environment. An integral combustion chamber/nozzle was designed and fabricated with a silica/phenolic ablative liner and a carbon/epoxy structural overwrap. This paper describes the fabrication process and developmental hurdles overcome for the Fastrac engine one-piece composite combustion chamber/nozzle.

Lawrence, T.↗

Comparative Analysis of Two Cryogenic Force Balance Calibration Systems

Cryogenic wind-tunnel facilities face unique challenges in the calibration and operation of various measurement systems and instrumentation. Instruments that are subjected to the cryogenic conditions of the test plenum require careful design and calibration procedures to maintain instrument performance. NASA’s National Transonic Facility (NTF) and the European Transonic Windtunnel (ETW) are two cryogenic wind-tunnel facilities, each with the ability to calibrate force measurement systems (FMS) at cryogenic conditions. These facilities have different methodologies and processes for calibrating these systems. This paper discusses differences in the methodologies and processes and compares the results of two separate cryogenic calibrations of the NTF-118A force balance that were completed at both wind-tunnel facilities.

Toro, Kenneth G.↗

Lead-Free Double-Base Propellant for the 2.75 Inch Rocket Motor

The current MK 66 2.75 inch Rocket Motor double-base propellant contains the lead-based ballistic modifier LC-12-15 to achieve the desired plateau and mesa burning rate characteristics. The use of lead compounds poses a concern for the environment and for personal safety due to the metal's toxic nature when introduced into the atmosphere by propellant manufacture, rocket motor firing, and disposal. Copper beta-resorcylate (copper 2,4-di-hydroxy-benzoate) was successfully used in propellant as a simple modifier in the mid 1970's. This and other compounds have also been mixed with lead salts to obtain more beneficial ballistic results. Synthesized complexes of lead and copper compounds soon replaced the mixtures. The complexes incorporate the lead, copper lack of organic liquids, which allows for easier propellant processing. About ten years ago, the Indian Head Division, Naval Surface Warfare Center (NSWC), initiated an effort to develop a lead-free propellant for use in missile systems. Several lead-free propellant candidate formulations were developed. About five years ago, NSWC, in conjunction with Alliant Techsystems, Radford Army Ammunition Plant, continued ballistic modifier investigations. A four component ballistic modifier system without lead for double-base propellants that provide adequate plateau and mesa burn rate characteristics was developed and patented. The ballistic modifier's system contains bismuth subsalicylate, 1.5 percent; copper salicylate, 1.0 percent, copper stannate, 0.77 percent; and carbon black, 0.1 percent. Action time and impulse data obtained through multiple static firings indicate that the new lead-free double-base propellant, while not a match for NOSIH-AA-2, will be a very suitable replacement in the 2.75 inch Rocket Motor. Accelerated aging of the double-base propellant containing the lead-free ballistic modifier showed that it had a much higher rate of stabilizer depletion than the AA-2. A comprehensive study showed that an increased rate of stabilizer depletion occurred in propellants containing monobasic copper salicylate. The study also showed that propellants containing a mixture of bismuth subsalicylate and copper salicylate, had only about one-half the stabilizer depletion rate than those with copper salicylate alone. The copper salicylate catalyzes the decomposition of nitroglycerin, which triggers a chain of events leading to the increased rate of stabilizer depletion. A program has been initiated to coat the ballistic modifier, thus isolating it from the nitroglycerin.

Magill, B. T.↗

Quantitative metrics for evaluating thermonuclear design codes and physics models applied to the National Ignition Campaign

In this study, physics models and design codes for hot dense plasmas undergoing thermonuclear burn are evaluated objectively using statistical metrics that compare the difference between calculations and data relative to the experimental uncertainties. The analysis is applied to the National Ignition Campaign (NIC) because it is relevant, comprehensive, and well documented. The statistics confirm that a key process afflicting NIC performance is mix driven by hydrodynamic instabilities as approximated here using the KL model [G. Dimonte and R. Tipton, Phys. Fluids 18, 085101 (2006)]. New physics models are also presented for instability-driven magnetic fields [B. Srinivasan et al., Phys. Rev. Lett. 108, 165002 (2012)] and the Coulomb logarithm for electron–ion thermal relaxation [G. Dimonte and J. Daligault, Phys. Rev. Lett. 101, 135001 (2008)]. The plasma-generated magnetic fields improve the agreement between code and data in a statistically significant manner by reducing the electron thermal conduction in the hot-spot via the Hall term. The Coulomb logarithm is presented in a numerically practical form that incorporates recent theoretical advances. However, it does not improve the agreement between the code and data because the thermal relaxation is so fast in non-ignited NIC plasmas that the typical 20% error does not change the tight coupling between electrons and ions. Even with these improved physics models, the one-dimensional simulations presented here are not able to describe the high-convergence NIC implosions in a statistically acceptable manner. Of the heroic multi-dimensional simulations of Clark et al. [Phys. Plasmas 23, 056302 (2016)], only those in three-dimensions satisfy the statistical acceptance criterion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Developing A Custom-Built Metal Aerosol Processing Chamber: Analysis of Aerosol Coagulation at Low Humidities

We have developed an intermediate size (906 L) aerosol processing chamber, and this work reports on the design and initial characterization of dry aerosol experiments. Specifically, we are determining wall-loss and coagulation correction factors using the observed size distribution measurements for surrogates of common aerosol classes: sodium chloride, sucrose, and biomass burning aerosol smoke. Results show that, on average, sodium chloride, sucrose, and smoke wall-loss rates converge to similar values on relatively short time scales (< 1 h). The fitted coagulation correction factor, W C -1 , for smoke particles (1.23 ± 0.312), indicates that on average they adhere to each other more than sodium chloride (0.969 ± 0.524) and sucrose (1.16 ± 1.38). The relative uncertainty is high for the coagulation correction, but it is consistent with our Monte Carlo error analysis. This study lays the foundation for future experiments at elevated humidity and supersaturation conditions to characterize the influence of particle shape on coagulation and cloud parameters.

54 ENVIRONMENTAL SCIENCES↗

Canning Of Powdered Metal For Hot Isostatic Pressing

Quality of specimen enhanced by improved canning process. Method developed for canning specimens for hot isostatic pressing. Specimen placed inside refractory-metal ring, then sandwiched between two refractory-metal face sheets. Assembly placed inside die, then positioned in vacuum hot press. Heated to set temperature at prescribed vacuum to burn off all of binder in specimen. Advantages: powder-metallurgy composite totally purged of binder sealed in can in single operation, maintains size, shape, and uniformity of specimen. Weld region does not recrystallize, and little possibility of cracking.

Juhas, John J.↗

Ignition transient analysis of solid rocket motor

To predict pressure-time and thrust-time behavior of solid rocket motors, a one-dimensional numerical model is developed. The ignition phase of solid rocket motors (time less than 0.4 sec) depends critically on complex interactions among many elements, such as rocket geometry, heat and mass transfer, flow development, and chemical reactions. The present model solves the mass, momentum, and energy equations governing the transfer processes in the rocket chamber as well as the attached converging-diverging nozzle. A qualitative agreement with the SRM test data in terms of head-end pressure gradient and the total thrust build-up is obtained. Numerical results show that the burning rate in the star-segmented head-end section and the erosive burning are two important parameters in the ignition transient of the solid rocket motor (SRM).

Han, Samuel S.↗

Enhanced alkaline hydrolysis and biodegradability studies of nitrocellulose-bearing missile propellant

Large amounts of energetic materials which have been accumulated over the years in various manufacturing and military installations must be disposed of in an environmentally sound manner. Historically, the method of choice for destruction of obsolete or aging energetic materials has been open burning or open detonation (OB/OD). This destruction approach has become undesirable due to air pollution problems. Therefore, there is a need for new technologies which will effectively and economically deal with the disposal of energetic materials. Along those lines, we have investigated a chemical/biological process for the safe destruction and disposal of a double base solid rocket propellant (AHH), which was used in several 8 inch projectile systems. The solid propellant is made of nitrocellulose and nitroglycerin as energetic components, two lead salts which act as ballistic modifiers, triacetin as a plasticizer and 2-Nitrodiphenylamine (2-NDPA) as a stabilizer. A process train is being developed to convert the organic components of the propellant to biodegradable products and remove the lead from the process stream. The solid propellant is first hydrolyzed through an enhanced alkaline hydrolysis process step. Following lead removal and neutralization, the digested liquor rich in nitrates and nitrites is found to be easily biodegradable. The digestion rate of the intact ground propellant as well as the release of nitrite and nitrate groups were substantially increased when ultrasound were supplied to the alkaline reaction medium compared to the conventional alkaline hydrolysis. The effects of reaction time, temperature, sodium hydroxide concentration and other relevant parameters on the digestion efficiency and biodegradability have been studied. The present work indicates that the AHH propellant can be disposed of safely with a combination of physiochemical and biological processes.

Sidhoum, Mohammed↗

Model Simulations of CO2 Transport Using Assimilated Meteorological Fields

The numerical simulation of CO2 transport (and other tracers such as CO, CH4, and biomass burning tracers) in the atmosphere is required to determine the fate of anthropogenic source gases. Estimation of the CO2 exchange between the ocean surface, the terrestrial biosphere, and the atmosphere is of first-order importance to understanding the global carbon cycle and the processes that are most crucial in determining the atmospheric CO2 concentration. Forward transport simulations have been conducted using two-dimensional, time-dependent grids of average surface fluxes (from TRANSCOM) and three-dimensional wind data from a prototype data assimilation system (FV-DAS) run by the Goddard Data Assimilation Office. The objective is to better understand the contribution of meteorological variability to changes in CO2 and other constituents, By accurately accounting for meteorological variability, through use of assimilated winds, we hope to better characterize the distribution of surface sources and sinks (and chemistry where applicable). With assimilated meteorology such chemistry/transport runs provide the basic framework to analyze existing (and proposed) measurement data on a point-by-point, real-time basis. We compare with measured CO2 concentration gradients on a daily, seasonal, regional, and interhemispheric basis to examine the consistency of sources, sinks, and transport formulation. We will also examine the inter-annual variability of atmospheric CO2 due to atmospheric circulation changes using longer runs with assimilated winds.

Kaea, S. R.↗

System Modeling of ORNL s 20 MW(t) Wood-fired Gasifying Boiler

We present an overview of the new 20 MW(t) wood-fired steam plant currently under construction by Johnson Controls, Inc. at the Oak Ridge National Laboratory in Tennessee. The new plant will utilize a low-temperature air-blown gasifier system developed by the Nexterra Systems Corporation to generate low-heating value syngas (producer gas), which will then be burned in a staged combustion chamber to produce heat for the boiler. This is considered a showcase project for demonstrating the benefits of clean, bio-based energy, and thus there is considerable interest in monitoring and modeling the energy efficiency and environmental footprint of this technology relative to conventional steam generation with petroleum-based fuels. In preparation for system startup in 2012, we are developing steady-state and dynamic models of the major process components, including the gasifiers and combustor. These tools are intended to assist in tracking and optimizing system performance and for carrying out future conceptual studies of process changes that might improve the overall energy efficiency and sustainability. In this paper we describe the status of our steady-state gasifier and combustor models and illustrate preliminary results from limited parametric studies.

09 BIOMASS FUELS↗

Technology demonstration for reducing mercury emissions from small-scale gold refining facilities.

Gold that is brought from artisanal and small-scale gold mining areas to gold shops for processing and sale typically contains 5-40% mercury. The uncontrolled removal of the residual mercury in gold shops by using high-temperature evaporation can be a significant source of mercury emissions in urban areas where the shops are located. Emissions from gold shop hoods during a burn can exceed 1,000 mg/m{sup 3}. Because the saturation concentration of mercury vapor at operating temperatures at the hood exhaust is less than 100 mg/m{sup 3}, the dominant component of the exhaust is in the form of aerosol or liquid particles. The U.S. Environmental Protection Agency (EPA), with technical support from Argonne National Laboratory (Argonne), has completed a project to design and test a technology to remove the dominant aerosol component in the emissions from gold shops. The objective was to demonstrate a technology that could be manufactured at low cost and by using locally available materials and manufacturing capabilities. Six prototypes designed by Argonne were locally manufactured, installed, and tested in gold shops in Itaituba and Creporizao, Brazil. The initial prototype design incorporated a pebble bed as the media for collecting the mercury aerosols, and a mercury collection efficiency of over 90% was demonstrated. Though achieving high efficiencies, the initial prototype was determined to have practical disadvantages such as excessive weight, a somewhat complex construction, and high costs (>US$1,000). To further simplify the construction, operation, and associated costs, a second prototype design was developed in which the pebble bed was replaced with slotted steel baffle plates. The system was designed to have flexibility for installation in various hood configurations. The second prototype with the baffle plate design was installed and tested in several different hood/exhaust systems to determine the optimal installation configuration. The significance of coagulation and collection of the mercury aerosols in exhaust ducts, which is dependent on the hood and collector configuration, was also evaluated. Prototype demonstration tests verified the theoretical basis for mercury aerosol capture that can be used to optimize the baffle plate design, flow rates, and hood exhaust ducts and plenum to achieve 80% or higher removal efficiencies. Results indicated that installation configuration significantly influences a system's capture efficiency. Configurations that retained existing inlet ducts resulted in system efficiencies of more than 80%, whereas installation configurations without inlet ducts significantly reduced capture efficiency. As an alternative to increasing the volume of inlet ducts, the number of baffle plates in the system baffle assembly could be doubled to increase efficiency. Recommended installation and operation procedures were developed on the basis of these results. A water-based mercury capture system developed in Indonesia for installation in smaller shops was also tested and shown to be effective for certain applications. The cost of construction and installation of the baffle plate prototype was approximately US$400. These costs were reported as acceptable by local gold shop owners and government regulators, and were significantly lower than the cost of an alternate charcoal/copper mesh mercury filter available in the region, which costs about US$10,000. A sampling procedure that consists of a particle filter combined with a vapor analyzer was demonstrated as an effective procedure for analyzing both the aerosol and vapor components of the mercury concentrations. Two key findings for enhancing higher mercury collection were identified. First, the aerosol/vapor mercury emissions must be given sufficient time for the mercury particles to coagulate to a size that can be readily captured by the baffle plates. An interval of at least 6 seconds of transit time between the point of evaporation and contact with the slotted baffle plates is recommended. Some particles will also deposit in the exhaust ducts between the point of evaporation and the baffle plates. Second, the slots in the baffle plates create jets that force the mercury particles to impinge and adhere on downstream surfaces. The baffle plates should closely follow the designs developed for this system to be most effective.

54 ENVIRONMENTAL SCIENCES↗

Continental heat anomalies and the extreme melting of the Greenland ice surface in 2012 and 1889: Melting of Greenland in 1889 and 2012

Recent decades have seen increased melting of the Greenland ice sheet. On 11 July 2012, nearly the entire surface of the ice sheet melted; such rare events last occurred in 1889 and, prior to that, during the Medieval Climate Anomaly. Studies of the 2012 event associated the presence of a thin, warm elevated liquid cloud layer with surface temperatures rising above the melting point at Summit Station, some 3212m above sea level. Here we explore other potential factors in July 2012 associated with this unusual melting. These include (1) warm air originating from a record North American heat wave, (2) transitions in the Arctic Oscillation, (3) transport of water vapor via an Atmospheric River over the Atlantic to Greenland, and (4) the presence of warm ocean waters south of Greenland. For the 1889 episode, the Twentieth Century Reanalysis and historical records showed similar factors at work. However, markers of biomass burning were evident in ice cores from 1889 which may reflect another possible factor in these rare events. We suggest that extreme Greenland summer melt episodes, such as those recorded recently and in the late Holocene, could have involved a similar combination of slow climate processes, including prolonged North American droughts/heat waves and North Atlantic warm oceanic temperature anomalies, together with fast processes, such as excursions of the Arctic Oscillation, and transport of warm, humid air in Atmospheric Rivers to Greenland. It is the fast processes that underlie the rarity of such events and influence their predictability.

54 ENVIRONMENTAL SCIENCES↗

A particulate model of solid waste incineration in a fluidized bed combining combustion and heavy metal vaporization

This study aims to develop a particulate model combining solid waste particle combustion and heavy metal vaporization from burning particles during MSW incineration in a fluidized bed. The original approach for this model combines an asymptotic combustion model for the carbonaceous solid combustion and a shrinking core model to describe the heavy metal vaporization. A parametric study is presented. The global metal vaporization process is strongly influenced by temperature. Internal mass transfer controls the metal vaporization rate at low temperatures. At high temperatures, the chemical reactions associated with particle combustion control the metal vaporization rate. A comparison between the simulation results and experimental data obtained with a laboratory-scale fluid bed incinerator and Cd-spiked particles shows that the heavy metal vaporization is correctly predicted by the model. The predictions are better at higher temperatures because of the temperature gradient inside the particle. Future development of the model will take this into account. (author)

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Doppler-resolved kinetics of saturation recovery

Frequency modulated laser transient absorption has been used to monitor the ground state rotational energy transfer rates of CN radicals in a double-resonance, depletion recovery experiment. When a pulsed laser is used to burn a hole in the equilibrium ground state population of one rotational state without velocity selection, the population recovery rate is found to depend strongly on the Doppler detuning of a narrow-band probe laser. Similar effects should be apparent for any relaxation rate process that competes effectively with velocity randomization. Alternative methods of extracting thermal rate constants in the presence of these non-thermal conditions are evaluated. Total recovery rate constants, analogous to total removal rate constants in an experiment preparing a single initial rotational level, are in good agreement with quantum scattering calculations, but are slower than previously reported experiments and show qualitatively different rotational state dependence between Ar and He collision partners. As a result, quasi-classical trajectory studies confirm that the differing rotational state dependence is primarily a kinematic effect.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantifying long-term seasonal and regional impacts of North American fire activity on continental boundary layer aerosols and cloud condensation nuclei

An intimate knowledge of aerosol transport is essential in reducing the uncertainty of the impacts of aerosols on cloud development. Datasets from the U. S. Department of Energy (DOE) Atmospheric Radiation Measurement platform in the Southern Great Plains region (ARM-SGP) and the NASA Modern-Era Retrospective Analysis for Research and Applications, version 2 (MERRA-2) showed seasonal increases in aerosol loading and total carbon concentration during the spring and summer months (2008-2016) which was attributed to fire activity and smoke transport within North America. The monthly mean MERRA-2 surface carbonaceous aerosol mass concentration and ARM-SGP total carbon products were strongly correlated (R=0.82, p<0.01) along with a moderate correlation with the ARM-SGP cloud condensation nuclei (N CCN ) product (0.5, p~0.1). The monthly mean ARM-SGP total carbon and N CCN products were strongly correlated (0.7, p~0.01). An additional product denoting fire number and coverage taken from the National Interagency Fire Center (NIFC) showed a moderate correlation with the MERRA-2 carbonaceous product (0.45, p<0.01) during the 1981-2016 warm season months (March-September). With respect to meteorological conditions, the correlation between the NIFC fire product and MERRA-2 850 hPa isobaric height anomalies was lower (0.26, p~0.13) due to the variability in the frequency, intensity, and number of fires in North America. An observed increase in the isobaric height anomaly during the past decade may lead to frequent synoptic ridging and drier conditions with more fires, thereby potentially impacting cloud/precipitation processes and decreasing air quality.

54 ENVIRONMENTAL SCIENCES↗