Search NASA⌕ Search

SEARCH · Search NASA

Results for “Edge Computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Probing Terra Incognita of Ni–P Catalysts: Operando Explorations during Hydrogen Evolution Reaction

We have developed two Ni phosphide preparation methods allowing operando XAS surface-sensitive studies of well-defined bulk systems. For Ni K-edge XAS, a Ni 2 P phase-pure powder was sintered into a high-density pellet and polished for grazing incidence XAS. Ni sites were mildly affected by the acidic electrolyte prior to the HER, while the applied cathodic potential caused the reduction of Ni surface states beyond the states of as-prepared Ni 2 P. The computed fully H-covered Ni 2 P [0001] model describes the difference in the operando Ni K-edge GIXAS spectrum well. Upon turning the applied bias off, the Ni sites became immediately oxidized, forming NiO on the surface. Thus, the active phase during the HER is covalent Ni 0 close to that in the intermetallic phosphides, and Ni 2+ oxides formed after, and not during, the HER. For P K-edge XAS, Ni foam was phosphorized to form a thin Ni 3 P layer while preserving its high surface area. Upon immersion in the acidic electrolyte, the P sites underwent removal of P 5+ phosphates and formed new P coordination, possibly due to the adsorption of protons from the electrolyte. These new P surface states were not affected by turning the cathodic current on and off as soon as the sample was immersed in the acidic electrolyte. However, the removal of the sample from the electrochemical cell and drying in air resulted in substantial depletion and oxidation of surface P. Echoing the observed Ni site chemistry during HER, XAS and XPS suggest that the in situ active P sites are different from the oxidized P states observed under ex situ conditions.

Kong, Seongyoung [Iowa State Univ., Ames, IA (Unit↗

Application of Parallel Adjoint-Based Error Estimation and Anisotropic Grid Adaptation for Three-Dimensional Aerospace Configurations

This paper demonstrates the extension of error estimation and adaptation methods to parallel computations enabling larger, more realistic aerospace applications and the quantification of discretization errors for complex 3-D solutions. Results were shown for an inviscid sonic-boom prediction about a double-cone configuration and a wing/body segmented leading edge (SLE) configuration where the output function of the adjoint was pressure integrated over a part of the cylinder in the near field. After multiple cycles of error estimation and surface/field adaptation, a significant improvement in the inviscid solution for the sonic boom signature of the double cone was observed. Although the double-cone adaptation was initiated from a very coarse mesh, the near-field pressure signature from the final adapted mesh compared very well with the wind-tunnel data which illustrates that the adjoint-based error estimation and adaptation process requires no a priori refinement of the mesh. Similarly, the near-field pressure signature for the SLE wing/body sonic boom configuration showed a significant improvement from the initial coarse mesh to the final adapted mesh in comparison with the wind tunnel results. Error estimation and field adaptation results were also presented for the viscous transonic drag prediction of the DLR-F6 wing/body configuration, and results were compared to a series of globally refined meshes. Two of these globally refined meshes were used as a starting point for the error estimation and field-adaptation process where the output function for the adjoint was the total drag. The field-adapted results showed an improvement in the prediction of the drag in comparison with the finest globally refined mesh and a reduction in the estimate of the remaining drag error. The adjoint-based adaptation parameter showed a need for increased resolution in the surface of the wing/body as well as a need for wake resolution downstream of the fuselage and wing trailing edge in order to achieve the requested drag tolerance. Although further adaptation was required to meet the requested tolerance, no further cycles were computed in order to avoid large discrepancies between the surface mesh spacing and the refined field spacing.

Lee-Rausch, E. M.↗

Application of CFD to a generic hypersonic flight research study

Computational analyses have been performed for the initial assessment of flight research vehicle concepts that satisfy requirements for potential hypersonic experiments. Results were obtained from independent analyses at NASA Ames, NASA Langley, and Sandia National Labs, using sophisticated time-dependent Navier-Stokes and parabolized Navier-Stokes methods. Careful study of a common problem consisting of hypersonic flow past a slightly blunted conical forebody was undertaken to estimate the level of uncertainty in the computed results, and to assess the capabilities of current computational methods for predicting boundary-layer transition onset. Results of this study in terms of surface pressure and heat transfer comparisons, as well as comparisons of boundary-layer edge quantities and flow-field profiles are presented here. Sensitivities to grid and gas model are discussed. Finally, representative results are presented relating to the use of Computational Fluid Dynamics in the vehicle design and the integration/support of potential experiments.

Green, Michael J.↗

Band Edge Control of Quasi–2D Metal Halide Perovskites for Blue Light–Emitting Diodes with Enhanced Performance

Perovskite light–emitting diodes (PeLEDs) have received great attention for their potential as next–generation display technology. While remarkable progress has been achieved in green, red, and near–infrared PeLEDs with external quantum efficiencies (EQEs) exceeding 20%, obtaining high performance blue PeLEDs remains a challenge. Poor charge balance due to large charge injection barriers in blue PeLEDs has been identified as one of the major roadblocks to achieve high efficiency. Here band edge control of perovskite emitting layers for blue PeLEDs with enhanced charge balance and device performance is reported. By using organic spacer cations with different dipole moments, that is, phenethyl ammonium (PEA), methoxy phenethyl ammonium (MePEA), and 4–fluoro phenethyl ammonium (4FPEA), the band edges of quasi–2D perovskites are tuned without affecting their band gaps. Furthermore, detailed characterization and computational studies have confirmed the effect of dipole moment modification to be mostly electrostatic, resulting in changes in the ionization energies of ≈0.45 eV for MePEA and ≈ –0.65 eV for 4FPEA based thin films relative to PEA–based thin films. With improved charge balance, blue PeLEDs based on MePEA quasi–2D perovskites show twofold increase of the EQE as compared to the control PEA based devices.

36 MATERIALS SCIENCE↗

Vibration and local edge buckling of thermally stressed, wedge airfoil cantilever wings.

The local edge buckling phenomena that can occur along the heated thin edge of a wedge shape airfoil is calculated. Qualitative comparison (qualitative only because the experimental temperature distribution was not measured) is made to the experimentally observed phenomena. The consequences of the assumption of identical vibration and buckling modes is shown by a comparison of results with and without the assumption of mode identity. Computer plots of the elastic surface as local buckling develops with increasing temperature are shown. The calculated, fully developed local edge buckling is compared to a photograph of a fully developed buckling as observed in the laboratory.

Bailey, C. D.↗

Risks of secondary malignancies with heterotopic bone radiation therapy for patients younger than 40 years

Heterotopic ossification (HO) of the bone is defined as a benign condition in which abnormal bone formation occurs in soft tissue. One of the most common prophylactic treatments for HO is radiation therapy (RT). This study retrospectively reviewed 20 patients younger than the age of 40 who received radiation to prevent HO in a single fraction of 7 Gray. The purpose of this study is to assess the risk of a second malignancy in these patients by recreating their treatment fields and contouring organs at risk to estimate the radiation dose absorbed by normal tissues outside the radiation treatment field. Diagnostic computed tomography (CT) scans for each patient were used to recreate treatment fields and to calculate dose to structures of interest. The distance from the field edge to each structure and its depth was recorded. Dose measurements in a water phantom were performed for the range of depths, distances, and field sizes used in the actual treatment plans. Computer-generated doses were compared to estimates based on measurement. The structure dose recorded was the higher dose generated between the 2 methods. Scatter dose was recorded to the rectum, bladder, sigmoid colon, small bowel, ovaries and utero-cervix in female patients, and prostate and gonads in male patients. In some patients, there is considerable dose received by certain organs from scatter because of their proximity to the radiation field. The average dose to the ovarian region was 4.125 Gy with a range of 1.085 to 6.228 Gy. The risk estimate for these patients ranged from 0.16% to 0.93%. The average total lifetime risk estimate for the bladder in all patients is 0.22% and the average total lifetime risk estimate for the remainder organs in all patients is 1.25%. In conclusions, proper shielding created from multileaf collimators (MLCs), blocks, and shields should always be used when possible.

61 RADIATION PROTECTION AND DOSIMETRY↗

Full-wave feasibility study of anti-radar diagnostic of magnetic field based on O-X mode conversion and oblique reflectometry imaging

An innovative millimeter wave diagnostic is proposed to measure the local magnetic field and edge current as a function of the minor radius in the tokamak pedestal region. The idea is to identify the direction of minimum reflectivity at the O-mode cutoff layer. Correspondingly, the transmissivity due to O-X mode conversion is maximum. That direction, and the angular map of reflectivity around it, contains information on the magnetic field vector B at the cutoff layer. Probing the plasma with different wave frequencies provides the radial profile of B. Full-wave finite-element simulations are presented here in 2D slab geometry. Modeling confirms the existence of a minimum in reflectivity that depends on the magnetic field at the cutoff, as expected from mode conversion physics, giving confidence in the feasibility of the diagnostic. The proposed reflectometric approach is expected to yield superior signal-to-noise ratio and to access wider ranges of density and magnetic field, compared with related radiometric techniques that require the plasma to emit electron Bernstein waves. Due to computational limitations, frequencies of 10-20 GHz were considered in this initial study. Frequencies above the edge electron-cyclotron frequency (f > 28 GHz here) would be preferable for the experiment, because the upper hybrid resonance and right cutoff would lie in the plasma, and would help separate the O-mode of interest from spurious X-waves.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

IT roadmap requirements for research and development

In 2009, members representing the programmatic community of the Laboratory presented a request to the Information Architecture Steering Committee (IASC) to form a committee within the Information Architecture Program (IAP) to review and consider the needs of researchers. In response, a Research and Development Subteam under the Infrastructure Team was created. Members included volunteer representatives of groups performing research and development throughout the Laboratory. This paper represents the product of this review. The R&D computing environment has languished while Los Alamos has been very compliance driven for the past few years under a set of directives that have eliminated our ability to innovate and to push the envelope of R&D computing. The appeal for outside collaborations is rapidly becoming tarnished, as colleagues from outside the NNSA environment view our restrictions as increasingly oppressive. We are losing the ability to conduct cutting-edge research and losing money to competitors who are able to quickly react and pursue program dollars while we are still creating compliant but less than useful computing solutions. Research programs depend on collaboration, employees, foreign nationals, and frequent travel, including travel to foreign countries. Solutions need to facilitate these activities and be based on the risk that the activities actually pose to the infrastructure and data at LANL. Furthermore, when problems are solved, it is essential that the solutions are evaluated for cost/benefit to the programs, that programmatic impact is well identified, and that solutions have sufficient long term resource for collaborations.

99 GENERAL AND MISCELLANEOUS↗

Inviscid and viscous flow calculations for the F16XL configuration

The viewgraphs and discussion of the ongoing activity at NASA Langley Research Center (LaRC) in support of Supersonic Laminar FLow Control (SLFC) research, presented at the High-Speed Research Workshop, May 14-16, 1991, are provided. Details of the computation involved in obtaining the meanflow around bodies in high-speed flow and interfacing the results to a stablilty analysis is presented. Particular attention is given to the F-16XL configuration, which is the test-bed for the supersonic LFC experiment. Meanflow solutions for two geometries are discussed. The first one is for the F-16XL wing, with emphasis on the flow near the attachment line and the upper surface. Calculations were done with and without suction. The results were processed using an interface program and fed into a stability analysis program. The second geometry is a scale model of a swept wing leading edge at M = 3.5. Experimental measurements on transition on this model are planned at NASA LaRC. The computations are in support of this effort.

Iyer, Venkit↗

Towards quasi-transverse momentum dependent PDFs computable on the lattice

Transverse momentum dependent parton distributions (TMDPDFs) which appear in factorized cross sections involve infinite Wilson lines with edges on or close to the light-cone. Since these TMDPDFs are not directly calculable with a Euclidean path integral in lattice QCD, we study the construction of quasi-TMDPDFs with finite-length spacelike Wilson lines that are amenable to such calculations. We define an infrared consistency test to determine which quasi-TMDPDF definitions are related to the TMDPDF, by carrying out a one-loop study of infrared logarithms of transverse position b T ~Λ QCD -1 , which must agree between them. This agreement is a necessary condition for the two quantities to be related by perturbative matching. TMDPDFs necessarily involve combining a hadron matrix element, which nominally depends on a single light-cone direction, with soft matrix elements that necessarily depend on two light-cone directions. We show at one loop that the simplest definitions of the quasi hadron matrix element, the quasi soft matrix element, and the resulting quasi-TMDPDF all fail the infrared consistency test. Ratios of impact parameter quasi-TMDPDFs still provide nontrivial information about the TMD-PDFs, and are more robust since the soft matrix elements cancel. We show at one loop that such quasi ratios can be matched to ratios of the corresponding TMDPDFs. We also introduce a modified “bent” quasi soft matrix element which yields a quasi-TMDPDF that passes the consistency test with the TMDPDF at one loop, and discuss potential issues at higher orders.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Influence of two-dimensional hygrothermal gradients on interlaminar stresses near free edges

Interlaminar stresses are determined for mechanical loading, uniform hygrothermal loading, and gradient moisture loading through implementation of a finite element computer code. Nonuniform two-dimensional hygroscopic gradients are obtained from a finite difference solution of the diffusion equation. It is shown that hygroscopic induced stresses can be larger than those resulting from mechanical and thermal loading, and that the distribution of the interlaminar normal stress may be changed significantly in the presence of a two-dimensional moisture gradient in the boundary layer of a composite laminate.

Farley, G. L.↗

Navier-Stokes computations for exotic airfoils

A hyperbolic grid generator with improvements for handling sharp corners and concave surfaces combined with a Navier-Stokes flow solver is applied to complex two dimensional airfoil configurations. Steady separated flow about an iced leading edge of an airfoil is presented. Unsteady viscous separated flows past an airfoil at two angles of attack with a spoiler deployed at 60 deg are compared with experiment. The spoiler computations are performed with two different topological maps of the physical domain to the computational domain. Graphical techniques for the static and unsteady display of the flow fields are discussed.

Barth, T. J.↗

Navier-Stokes computations for circulation controlled airfoils

Navier-Stokes computations of subsonic to transonic flow past airfoils with augmented lift due to rearward jet blowing over a curved trailing edge are presented. The approach uses a spiral grid topology. Solutions are obtained using a Navier-Stokes code which employs an implicit finite difference method, an algebraic turbulence model, and developments which improve stability, convergence, and accuracy. Results are compared against experiments for no jet blowing and moderate jet pressures and demonstrate the capability to compute these complicated flows.

Pulliam, T. H.↗

Navier-Stokes computations for circulation control airfoils

Navier-Stokes computations of subsonic to transonic flow past airfoils with augmented lift due to rearward jet blowing over a curved trailing edge are presented. The approach uses a spiral grid topology. Solutions are obtained using a Navier-Stokes code which employs an implicit finite difference method, an algebraic turbulence model, and developments which improve stability, convergence, and accuracy. Results are compared against experiments for no jet blowing and moderate jet pressures and demonstrate the capability to compute these complicated flows.

Pulliam, Thomas H.↗

Simulation and Modeling of Flow Generated by Gust Generator in a Wind Tunnel

A computational study of a gust field generated by a gust generator in a low-speed wind tunnel. The gust generator is designed for the University of Washington Aeronautical Laboratory (UWAL) Kirsten wind tunnel for a gust load alleviation (GLA) control experiment of a Common Research Model (CRM) flexible wing utilizing the Variable Camber Continuous Trailing Edge Flap (VCCTEF). The gust generator comprises four horizontal NACA 0015 gust generator vanes placed upstream of the test section. Computational fluid dynamics simulations using a two-dimensional (2D) Unsteady-Reynolds-Averaged-Navier-Stokes (URANS) with k-ω Shear Stress Transport (SST) turbulence model provide detailed time-resolved information about the generated flow by the gust generator under prescribed sinusoidal motion. The characteristics of the induced flow by the gust generator are analyzed. A gust propagation model of the gust field is investigated. An unsteady lift model is developed using a varying-fidelity approach which includes a 2D interference aerodynamic model of the combined gust generator-wing system. The computed integrated unsteady lift is compared to experimental data for validation of the unsteady lift model. Both the amplitude and transport delay are found to be accurately captured by the unsteady lift model.

Nhan, Nguyen↗

Transforming Benzophenoxazine Laser Dyes into Chromophores for Dye-Sensitized Solar Cells: A Molecular Engineering Approach

The re-functionalization of a series of four well-known industrial laser dyes, based on benzophenoxazine, is explored with the prospect of molecularly engineering new chromophores for dye-sensitized solar cell (DSC) applications. Such engineering is important since a lack of suitable dyes is stifling the progress of DSC technology. The conceptual idea involves making laser dyes DSC-active by chemical modification, while maintaining their key property attributes that are attractive to DSC applications. This molecular engineering follows a step-wise approach. Firstly, molecular structures and optical absorption properties are determined for the parent laser dyes: Cresyl Violet (1); Oxazine 170 (2); Nile Blue A (3), Oxazine 750 (4). These reveal structure-property relationships which define the prerequisites for computational molecular design of DSC dyes; the nature of their molecular architecture (D-π-A) and intramolecular charge transfer. Secondly, new DSC dyes are computationally designed by the in silico addition of a carboxylic acid anchor at various chemical substitution points in the parent laser dyes. A comparison of the resulting frontier molecular orbital energy levels with the conduction band edge of a TiO2 DSC photoanode and the redox potential of two electrolyte options I-/I3- and Co(II/III)tris(bipyridyl) suggests promise for these computationally designed dyes as co-sensitizers for DSC applications.

dye co-sensitization↗