Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite Properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Granular flow in pebble bed reactors: Dust generation and scaling

In experimental prototypes of pebble bed reactors, significant quantities of graphite dust have been observed due to rubbing between pebbles as they flow through the core. At the high temperatures and pressures in these reactors, little data is available to understand the frictional properties of the pebble surfaces, and as a result, the Paul Scherrer Institut (Switzerland) proposes a conceptual design of a scaled-down version of a pebble bed reactor to investigate this issue in detail. In this paper, simulations of granular flow in pebble bed reactors using the discrete-element method are presented. Simulations in the full geometry (using 440,000 pebbles) are compared to those in geometries scaled down by 3:1 and 6:1. The simulations show complex behavior due to discrete pebble packing effects, meaning that pebble flow and dust generation in a scaled-down facility may be significantly different. The differences between velocity profiles, packing geometry, and pebble wear at the different scales are discussed. The results can aid in the design of the prototypical facility to more accurately reproduce the flow in a full-size reactor. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Direct Measurement of EGR Cooler Deposit Thermal Properties for Improved Understanding of Cooler Fouling

Exhaust gas recirculation (EGR) cooler fouling has become a significant issue for compliance with NOx emissions standards. This paper reports results of a study of fundamental aspects of EGR cooler fouling. An apparatus and procedure were developed to allow surrogate EGR cooler tubes to be exposed to diesel engine exhaust under controlled conditions. The resulting fouled tubes were removed and analyzed. Volatile and non-volatile deposit mass was measured for each tube. Thermal diffusivity of the deposited soot cake was measured by milling a window into the tube and using the Xenon flash lamp method. The heat capacity of the deposit was measured at temperatures up to 430°C and was slightly higher than graphite, presumably due to the presence of hydrocarbons. These measurements were combined to allow calculation of the deposit thermal conductivity, which was determined to be 0.041 W/mK, only ~1.5 times that of air and much lower than the 304 stainless steel tube (14.7 W/mK). The main determinant of the deposit thermal conductivity is density, which was measured to be just 2% that of the density of the primary soot particles (or 98% porous). The deposit layer thermal resistance was calculated and compared with estimates of the thermal resistance calculated from gas temperature data during the experiment. The deposit properties were also used to further analyze the temperature data collected during the experiment.

33 ADVANCED PROPULSION SYSTEMS↗

Structural, Thermal, and Mechanical Characterization of a Thermally Conductive Polymer Composite for Heat Exchanger Applications

Polymer composites are being considered for numerous thermal applications because of their inherent benefits, such as light weight, corrosion resistance, and reduced cost. In this work, the microstructural, thermal, and mechanical properties of a 3D printed polymer composite with high thermal conductivity are examined using multiple characterization techniques. Infrared spectroscopy and X-ray diffraction reveal that the composite contains a polyphenylene sulfide matrix with graphitic fillers, which is responsible for the high thermal conductivity. Furthermore, differential scanning calorimetry determines that the glass transition and melting point of the composite are 87.6 °C and 285.6 °C, respectively. Thermogravimetric analysis reveals that the composite is thermally stable up to ~400 °C. Creep tests are performed at different isotherms to evaluate the long-term performance of the composite. The creep result indicates that the composite can maintain mechanical integrity when used below its glass transition temperature. Nanoindentation tests reveal that modulus and hardness of the composite is not significantly influenced by heating or creep conditions. These findings indicate that the composite is potentially suitable for heat exchanger applications.

36 MATERIALS SCIENCE↗

Enhancing the multi-functional properties of renewable lignin carbon fibers via defining the structure–property relationship using different biomass feedstocks

Lignin has been explored extensively as a renewable precursor for carbon materials, considering its abundance as a major component of plant cell walls and its sustainability as a byproduct of both lignocellulosic biorefinery and the paper-making industry. Despite the extensive efforts to define the process–property relationship, it remains largely unknown how lignin biosynthesis and its chemistry would impact the resultant carbon fiber properties, for both mechanical and electroconductive performances. Such inadequate understanding fundamentally limits feedstock design and selection to improve carbon fiber properties toward broader commercial applications. Using lignin from a broad range of biomass feedstocks for carbon fiber manufacturing, we have fundamentally explored the structure–function relationship between lignin chemistry and carbon fiber performance. Specifically, lignin extracted from hardwood (sugar maple), softwood (loblolly pine and red cedar), and herbaceous plants (corn stover and switchgrass) was used for carbon fiber manufacturing, considering the very different lignin structures from these feedstocks. Linear regression models were established to define the relationship between carbon fiber mechanical properties and lignin structural characteristics. The results highlighted that the content of β-O-4 linkages correlates significantly with the tensile strength and elastic modulus of lignin carbon fibers, indicating that more linear β-O-4 linkages would promote the carbon fiber mechanical performance. Moreover, electroconductive properties are essential for broader energy device application of lignin-based carbon fibers, yet the mechanisms controlling their electroconductivity are largely unknown. Furthermore, we hereby demonstrated that a higher β-O-4 content also promotes the electroconductivity of lignin carbon fibers. Microstructure analysis further revealed that the crystallite size and content of the pre-graphitic turbostratic carbon structure in lignin-based carbon fibers were enhanced as the β-O-4 linkages increased. The content of β-O-4 linkages has shown a strong correlation with the crystallite content in a linear regression model. This study thus revealed the underlying mechanisms regarding how the lignin structure in planta defines the resultant carbon fiber properties. Moreover, the study also highlighted the correlation between the mechanical and electroconductive properties of lignin-based carbon fibers, both of which were defined by the lignin structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Potential contour shaping and sheath behavior with wall electrodes and near-wall magnetic fields in Hall thrusters

Graphite electrodes are embedded within the discharge channel of a Hall effect thruster to focus ions for improved performance. Cusp-shaped magnetic fields are added around the electrodes to shield the electrodes from high electron current. Internal plasma potential measurements inside the discharge channel show that the presence of floating graphite does not significantly affect the potential contours at 150 V anode potential. Creation of closed contour pockets are observed with the electrodes biased 10 and 30 V above the anode potential. The electrodes also cause a compression of the acceleration region in the thruster. The cause of the changes in the potential contours is attributed to a shifting of discharge electrode from the anode to the electrodes and an expansion of the near-wall plasma sheath. The presence of the cusp magnetic fields is shown to affect the current collected by the electrodes, a behavior associated with modification of the plasma sheath properties due to magnetization of electrons.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A thermal study of amorphous and textured carbon and carbon nitride thin films via transient grating spectroscopy

Here in this study, we are considering a novel way of growing carbon nitride (CN) films by using High Power Impulse Magnetron Sputtering (HiPIMS). Carbon and CN thin films were grown on silicon substrate with varying nanocrystalline texturing: some samples were amorphous while others were either nanocrystalline graphite (for the carbon sample) or fullerene-like (for the CN sample), with both samples having a graphitic nanostructure vertically ordered throughout the film. Their thermal diffusivity was computed using transient grating spectroscopy in order to compare the impact of the material's nanostructure on its thermal property as well as benchmarking the performance of CN. It was found that the thermal properties of carbon thin films were decreased when doped with nitrogen, which is attributed to the increased atomic disorder introduced by the nitrogen cross-linking, impacting the phonon propagation. The impact of nitrogen doping on thermal properties opens new avenues in engineering materials with tailored and varying thermal properties at the microscale.

42 ENGINEERING↗

Electronic Transport Properties of Chemically Modified Double-Walled Carbon Nanotubes

We present a study on the quantum transport properties of chemically functionalized metallic double-walled carbon nanotubes (DWNTs) with lengths reaching the micrometer scale. First-principles calculations evidence that, for coaxial tubes separated by the typical graphitic van der Waals bond distance, the chemical modification of the outer wall with sp3-type defects affects the electronic structure of both the outer and the inner tube, which reduces significantly the charge transport capability of the DWNTs. For larger spacing between sidewalls, the conductivity of the outer wall decreases with increasing functional group coverage density, while charge transport in the inner tube is equivalent to that of a pristine nanotube. Additionally, [2 + 1] cycloaddition of CCl2 onto the outer DWNT sidewall barely affects the hyperconjugated π-network of the double wall, and charge transport remains in the quasi-ballistic regime. These results indicate an efficient route for tailoring electronic transport in DWNTs provided inner shell geometry and grafted functional groups are properly chosen.

Chemistry↗

Grinding Wear Behaviour of Stepped Austempered Ductile Iron as Media Material During Comminution of Iron Ore in Ball Mills

An attempt has been made to evaluate the suitability of austempered ductile iron (ADI) as media material for grinding iron ore in a ball mill. Spheroidal graphite (S.G) iron balls are austenitised at 900 deg. C for 60 minutes and given stepped austempering treatment at 280 deg. C for 30 minutes and 60 minutes followed by 380 deg. C for 60 minutes in each case. These materials are characterised by measuring hardness, analysing X-ray diffraction (X-RD), studying microstructure using optical and scanning electron microscope (SEM). Grinding wear behaviour of these materials was assessed for wear loss in wet condition at different pH value of the mineral slurry and found that the wear rate of grinding media material decreases with increase in pH of the slurry. The wear resistance of ADI balls were compared with forged En31 steel balls and found that the stepped austempered ductile iron is superior to forged En31 steel balls.

36 MATERIALS SCIENCE↗

Hydrostatic Microextrusion of Steel and Copper

The paper presents an experimental investigation based on hydrostatic micro extrusion of billets in low carbon steel and commercially pure copper, and the relevant results. The starting billets have a diameter of 0.3 mm and are 5 mm long; a high pressure generator consisting of a manually operated piston screw pump is used to pressurize the fluid up to 4200 bar, the screw pump is connected through a 3-way distribution block to the extrusion die and to a strain gauge high pressure sensor. The sensor has a full scale of 5000 bar and the extrusion pressure is acquired at a sampling rate of 2 kHz by means of an acquisition program written in the LabVIEW environment. Tests have been conducted at room temperature and a lubricant for wire drawing (Chemetall Gardolube DO 338) acts both as the pressurizing fluid and lubricant too. In addition, billets were graphite coated. Different fluid pressures and process durations have been adopted, resulting in different extrusion lengths. The required extrusion pressure is much higher than in non-micro forming operations (this effect is more evident for steel). On the cross section of the extruded parts, hardness and grain size distribution have been measured, the former through Vickers micro hardness (10 g load) tests. In the case of the extrusion of copper, the material behaves as in microdrawing process. In the case of the extrusion of steel, the hardness increases from the core to the surface as in the drawing process, but with lower values. The analysis evidenced the presence of the external layer, but its thickness is about 1/3 of the external layer in the drawn wire and the grains appear smaller than in the layer of the drawn wire. The extruding force required along the extruding direction is higher (22-24 N) than the drawing force along the same direction (12 N): being the material, the reduction ratio, the die sliding length the same in both cases, the higher extrusion force should be caused by a higher tangential friction force and/or a higher redundant work of deformation and/or a different material behaviour. Which is the real mechanism is not clear at present, but surface layer grains in extrusion are more deformed than in wire drawing. For this reason the deformation inhomogeneity increases in extrusion and the material under the highly deformed surface layer should be subjected to lower strains, strain hardening and finally resulting in lower hardness.

36 MATERIALS SCIENCE↗

Low-temperature scanning tunneling microscopy and spectroscopy measurements of ultrathin Pb films

We have investigated the electronic properties of ultrathin Pb films by low temperature scanning tunneling microscopy and spectroscopy. Our results show that 30 nm thick Pb(111) films grown on atomically flat highly oriented pyrolytic graphite (HOPG) and on amorphous SiO 2 are both in the strong-coupling limit with transition temperature and energy gap close to the bulk value. Conductance maps and spectroscopy in the vortex state reveal a bound state at the center of the vortices, which suggest that the films are in the clean limit. Here, measurements of 3 nm Pb films grown on HOPG show a clear crossover to the weak-coupling regime and dirty limit.

36 MATERIALS SCIENCE↗

Raman spectroscopy of thermally perturbed carbon fibers: Discriminating spectral responses of modulus classes and defect types

The mechanical strength properties of carbon fibers are generally thought to be correlated with the presence of underlying atomic-level defects. These defects serve to break the underlying translational symmetry of the graphitic or graphene subunits of the fiber construction, resulting in the emergence of new Raman-active spectral features. However, historical attempts to classify the precise origin of defect contributions to the Raman spectra have been challenging because of indistinct and overlapping features in the carbon fiber Raman spectra. Further, while substantial research exists on high-temperature exposure in inert atmospheres for carbon fiber composites, comparatively less addresses microscale behaviors and Raman spectral alterations to monofilament carbon fibers exposed to high-temperature atmospheric environments. Here, we report Raman spectral responses of nine commercially available high-performance, polyacrylonitrile-based carbon fibers exposed to various atmospheric heat treatments. In this work, we introduce a model-independent characterization method, the integrated absolute difference, to quantify the spectral responses to heat treatment of different fiber modulus classes. We combine this new method with a newly reported strategy to standardize spectral fitting for carbon fibers. With this approach, we show that atomic-scale defects in the underlying fiber microstructure manifest in measurably distinct manners and have distinct responses to thermal perturbation. These combined approaches may lay the foundation for disentangling contributions from specific defects in the Raman spectra of carbon fibers.

36 MATERIALS SCIENCE↗

Composite material characterization for large space structures.

A program phase to characterize advanced composite materials for a large reflector support truss on the ATS F & G spacecraft is described. The selection of a Hercules Incorporated, 2002M graphite fiber reinforced epoxy material was based on criteria of spacecraft system requirements and the potential of this material to meet these requirements. The objective of this phase was to develop materials data required for development, design, fabrication, test, and flight of a graphite-fiber, reinforced-plastic spacecraft structure. Testing within a temperature range from -300 F to +200 F covered the generation of data for physical, mechanical, thermophysical, and space environmental properties for the selected material. Additional testing covered adhesive bonded joint materials within the temperature ranges of the spacecraft environment. Descriptions of the spacecraft, reflector support truss, design, requirements, materials, tests, and developed data are presented.

Macneill, C. E.↗

Advances in the analysis and design of adhesive-bonded joints in composite aerospace structures

Several aspects of adhesive-bonded joint analysis and design are presented from the reference of size of structure or load intensity. This integrates the individual characterizations of double-lap, single-lap, stepped-lap, tapered-lap and scarf joints. The paper includes an overview of bonded joint selection from the standpoints of design, fabrication, and processing, each bearing in mind the influence of such considerations on the strength of the joint. A case study is presented of the optimization of a specific relatively thick titanium-to-graphite epoxy stepped-lap joint, using the digital computer analysis program A4EG. The factors accounted for are adhesive plasticity, adherend stiffness imbalance, adherend thermal mismatch, and change of material properties within the range of temperature environment and with load direction. The strength increases obtainable by refining the initial design are demonstrated.

Hart-Smith, L. J.↗

Creep rupture of polymer-matrix composites

The time-dependent creep-rupture process in graphite-epoxy laminates is examined as a function of temperature and stress level. Moisture effects are not considered. An accelerated characterization method of composite-laminate viscoelastic modulus and strength properties is reviewed. It is shown that lamina-modulus master curves can be obtained using a minimum of normally performed quality-control-type testing. Lamina-strength master curves, obtained by assuming a constant-strain-failure criterion, are presented along with experimental data, and reasonably good agreement is shown to exist between the two. Various phenomenological delayed failure models are reviewed and two (the modified rate equation and the Larson-Miller parameter method) are compared to creep-rupture data with poor results.

Brinson, H. F.↗

Development of design allowable data for Celion 6000/LARC-160, graphite/polyimide composite laminates

A design allowables test program was conducted on Celion 6000/LARC-160 graphite polyimide composite to establish material performance over a 116 K (-250 F) to 589 K (600 F) temperature range. Tension, compression, in-plane shear and short beam shear properties were determined for uniaxial, quasi-isotropic and + or - 45 deg laminates. Effects of thermal aging and moisture saturation on mechanical properties were also evaluated. Celion 6000/LARC-160 graphite/polyimide can be considered an acceptable material system for structural applications to 589 K (600 F).

Ehret, R. M.↗

Graphite polystyryl pyridine (PSP) structural composites

PSP6022 M resin, PSP 6024 M resin and W 133 Thormel T 300 graphite fabric reinforced panels were fabricated and provided to NASA Ames Research Center. PSP6022 and PSP6024 characteristics, process specifications for the fabriation of prepregs and of laminates are detailed. Mechanical properties, thermomechanical properties and moisture resistance were evaluated. PSP6022 and PSP6024 appear as high performance thermostable systems, very easy to process, being soluble in MEK for prepregging and being cured at no more than 250C, and even 200C.

Malassine, B.↗

Evaluation and prediction of long-term environmental effects of nonmetallic materials

The properties of a number of nonmetallic materials were evaluated experimentally in simulated space environments in order to develop models for accelerated test methods useful for predicting such behavioral changes. Graphite-epoxy composites were exposed to thermal cycling. Adhesive foam tapes were subjected to a vacuum environment. Metal-matrix composites were tested for baseline data. Predictive modeling designed to include strength and aging effects on composites, polymeric films, and metals under such space conditions (including the atomic oxygen environment) is discussed. The Korel 8031-00 high strength adhesive foam tape was shown to be superior to the other two tested.

Papazian, H.↗

Control of Cast Iron Microstructure

The use of microgravity for industrial research in the processing of cast iron was investigated. Solidification experiments were conducted using the KC-135 and F-104 aircraft, and an experiment plan was developed for follow-on experiments using the Shuttle. Three areas of interest are identified: (1) measurement of thermophysical properties in the melt; (2) understanding of the relative roles of homogeneous nucleation, grain multiplication, and innocultants in forming the microstructure; and (3) exploring the possibility of obtaining an aligned graphite structure in hypereutectic Fe, Ni, and Co.

Graham, J.↗