Search NASA⌕ Search

SEARCH · Search NASA

Results for “Integral effect test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Modeling resonance interference by 0-D slowing-down solution with embedded self-shielding method

The resonance integral table based methods employing conventional multigroup structure for the resonance self-shielding calculation have a common difficulty on treating the resonance interference. The problem arises due to the lack of sufficient energy dependence of the resonance cross sections when the calculation is performed in the multigroup structure. To address this, a resonance interference factor model has been proposed to account for the interference effect by comparing the interfered and non-interfered effective cross sections obtained from 0-D homogeneous slowing-down solutions by continuous-energy cross sections. A rigorous homogeneous slowing-down solver is developed with two important features for reducing the calculation time and memory requirement for practical applications. The embedded self-shielding method (ESSM) is chosen as the multigroup resonance self-shielding solver as an integral component of the interference method. The interference method is implemented in the DeCART transport code. Verification results show that the code system provides more accurate effective cross sections and multiplication factors than the conventional interference method for UO{sub 2} and MOX fuel cases. The additional computing time and memory for the interference correction is acceptable for the test problems including a depletion case with 87 isotopes in the fuel region. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

U.S. Department of Energy: National Virtual Biotechnology Laboratory (Technical Report)

With funding from the CARES Act, the U.S Department of Energy (DOE) established the National Virtual Biotechnology Laboratory (NVBL) in March 2020 to address key challenges associated with the COVID-19 crisis. The NVBL brought together the broad scientific and technical expertise and resources of DOE’s 17 national laboratories to help tackle medical supply shortages, discover potential drugs to fight the virus, develop and validate COVID-19 testing methods, model disease spread and impact across the nation, and understand virus transport in buildings and the environment. National laboratory resources leveraged for this effort include a suite of world-leading user facilities broadly available to the research community, such as light and neutron sources, nanoscale science research centers, sequencing and biocharacterization facilities, and high-performance computing facilities. As part of the NVBL framework, DOE rapidly assembled five project teams to (1) identify new targets for medical therapeutics; (2) develop innovations in testing capabilities; (3) provide epidemiological and logistical support; (4) understand viral fate and transport in the environment; and (5) address supply chain bottlenecks by harnessing extensive additive manufacturing capabilities. Each research team was charged with defining high-impact projects that could be completed in a 6-month sprint while coordinating their developments with academia, other government agencies, and the private sector. Within months, NVBL teams used DOE’s high-performance computers and light and neutron sources to identify promising candidates for antibodies and antivirals that universities and drug companies are now evaluating. NVBL researchers also developed new diagnostic targets and sample collection approaches, and supported efforts by the U.S. Food and Drug Administration, Centers for Disease Control and Prevention, and U.S. Department of Defense to establish national guidelines used in administering millions of tests. Researchers used artificial intelligence and high-performance computing to produce near-real-time data analysis to forecast disease transmission, stress on public health infrastructure, and economic impact, which supported decision-makers at the local, state, and national levels. To minimize virus uptake and protect human health, NVBL teams studied how to control indoor virus movement. Researchers also produced innovations in materials and advanced manufacturing that mitigated shortages in test kits and personal protective equipment, creating nearly 1,000 new jobs. Through its NVBL framework, DOE has contributed significantly to the nation’s COVID response, demonstrating in only a few months the critical impact of its national laboratories. NVBL’s accomplishments demonstrate not only the powerful resource represented by DOE’s national laboratories working together to meet national needs, but also the effectiveness of the integrated NVBL framework for rapidly responding to emergencies with research and development solutions. Going forward, the NVBL is poised to apply the unique capabilities and expertise of the national laboratory complex to future national and international emergencies, both natural and engineered. Through this framework, DOE will continue to be an integral component of agency-wide efforts to prepare for and respond to biorisks and other crises. This technical report describes the goals, progress, and results of NVBL’s five project teams—Molecular Design for COVID-19 Therapeutics, COVID-19 Testing, Epidemiological Modeling, Viral Fate and Transport, and Materials and Manufacturing of Critical Supplies—and lists each team’s publications and research output.

42 ENGINEERING↗

Hard x-ray tomographic studies of the destruction of an energetic electron ring

A tomography system was designed and built at the Large Plasma Device to measure the spatial distribution of hard x-ray (100 KeV-3 MeV) emissivity. The x-rays were generated when a hot electron ring was significantly disrupted by a shear Alfven wave. The plasma is pulsed at 1 Hz (1 shot/s). A lead shielded scintillator detector with an acceptance angle defined by a lead pinhole is mounted on a rotary gimbal and used to detect the x-rays. The system measures one chord per plasma shot using only one detector. A data plane usually consists of several hundred chords. A novel Dot by Dot Reconstruction (DDR) method is introduced to calculate the emissivity profile from the line integrated data. In the experiments, there are often physical obstructions, which make measurements at certain angles impossible. The DDR method works well even in this situation. The method was tested with simulated data, and was found to be more effective than previously published methods for the specific geometry of this experiment. The reconstructed x-ray emissivity from experimental data by this method is shown.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

ELM sputter erosion modeling of a tungsten coated small angle slot divertor in DIII-D

We modeled plasma edge localized mode (ELM) sputter erosion for a Small Angle Slot divertor with a tungsten coated region (SAS-VW), designed for experiments in the DIII-D tokamak, and proposed for use in future advanced tokamaks. The simulations use a free-streaming, 1000 eV, C +6 and D +1 ELM impingement model, with SOLPS-ITER, ITMC-DYN, and REDEP/WBC code packages for background plasma, material response, and erosion/redeposition respectively. The results show ELM'ing plasma gross and net tungsten erosion fluxes of the mixed-material C/W surface peaking at the slot entrance region, and an order of magnitude higher than for non-ELMs. The per-pulse erosion, however, remains low, of order 0.5 nm, due to expected moderate ELM frequencies and duration in DIII-D. Here, the ELMs result in a ~25x higher peak sputtered W current leaving the divertor slot region, towards the core plasma, compared to the ELM-free plasma case. The time-integrated escape current, however, may not significantly affect core plasma high-Z contamination concerns, for a 1% ELM duty factor, but may be an issue for higher frequency ELMs. In general, the modeling results appear favorable for effective testing of the SAS-VW divertor in DIII-D, and extrapolation to innovative divertor designs in future ITER-like and DEMO fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Resonant enhancement of the Fulde-Ferell-Larkin-Ovchinnikov state in three dimensions by a one-dimensional optical potential

We describe an imbalanced superfluid Fermi gas in three dimensions within the path-integral framework. To allow for the formation of the Fulde-Ferell-Larkin-Ovchinnikov state (FFLO state), a suitable form of the saddle point is chosen, in which the pairs have a finite center-of-mass momentum. To test the correctness of this path-integral description, the zero-temperature phase diagram for an imbalanced Fermi gas in three dimensions is calculated, and compared to recent theoretical results. Subsequently, we investigate two models that describe the effect of imposing a one-dimensional (1D) optical potential on the three-dimensional (3D) imbalanced Fermi gas. We show that this 1D optical potential can greatly enlarge the stability region of the FFLO state, relative to the case of the 3D Fermi gas without 1D periodic modulation. Furthermore, it is shown that there exists a direct connection between the center-of-mass momentum of the FFLO pairs and the wave vector of the optical potential. We propose that this concept can be used experimentally to resonantly enhance the stability region of the FFLO state.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Support of the Development of EPP Plus SMT Design Method (FY2020 Test Results)

Experiments in support of the development of the integrated Elastic–Perfectly Plastic (EPP) analysis and Simplified Model Test (SMT) design methodology continued in FY 2020. The previously developed single-bar SMT (SBSMT) technique was successfully extended to tubular shaped Alloy 617 specimens for evaluation of the effect of primary pressure load on SMT creep-fatigue (CF) properties at 950°C. A series of pressurized SMT tests were performed with various elastic follow-up factors and strain ranges. The results show that the primary pressure load reduces the SMT CF cycles. The reduction of SMT CF life due to primary load was found to be dependent on strain ranges, elastic follow up and test temperatures. These results are crucial for verification of the EPP strain range analysis in the EPP+SMT evaluation procedure. Additionally, hold time effect on the SMT CF life cycles is a determining factor for generating the EPP+SMT CF design curves. Lack of test data in the high cycle and low strain range region results in major uncertainty in developing the design curves. In FY2020, experiments were designed, and testing started on Alloy 617 at 950°C to fill the gap in experimental data. The on-going CF and additional SMT CF with elastic follow-up at low strain ranges will generate the information needed to verify the methods for extrapolation to long hold time and finalize the EPP+SMT design method.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fracture mechanics criteria for turbine engine hot section components

The application of several fracture mechanics data correlation parameters to predicting the crack propagation life of turbine engine hot section components was evaluated. An engine survey was conducted to determine the locations where conventional fracture mechanics approaches may not be adequate to characterize cracking behavior. Both linear and nonlinear fracture mechanics analyses of a cracked annular combustor liner configuration were performed. Isothermal and variable temperature crack propagation tests were performed on Hastelloy X combustor liner material. The crack growth data was reduced using the stress intensity factor, the strain intensity factor, the J integral, crack opening displacement, and Tomkins' model. The parameter which showed the most effectiveness in correlation high temperature and variable temperature Hastelloy X crack growth data was crack opening displacement.

Meyers, G. J.↗

Compatibility experiments of facilities, materials, and propellants for electrothermal thrusters

Experiments were performed to determine the compatibility of materials and propellants for electro-thermal thrusters. Candidate propellants for resistojet propulsion include carbon dioxide, methane, hydrogen, ammonia, and hydrazine. The materials being examined are grain stabilized platinum for resistojets for Space station and rhenium for high performance resistojets for satellites. Heater mass loss and deterioration of materials were evaluated. A coiled tube of platinum, with yttria dispersed throughout the base material to inhibit grain growth, was tested in carbon dioxide at 1300 C for 2000 hr. Post-test examination indicated the platinum-yttria heater would last over 100 000 hr with less than 10 percent mass loss. Short-term compatibility tests were conducted to test the integrity of the platinum-yttria in hydrogen, methane, carbon dioxide/methane mixtures and ammonia environments. In each of these 100 hr tests, the platinum-yttria mass change indicated a minimum coil life of 100 000 hr. Facility related effects were investigated in materials tests using rhenium heated to high tempertures. Vacuum facility water reduction was monitored using a mass spectrometer. In vacuum environments obtained using only diffusion pumping and those obtained with the assistance of cryogenic equipment there were mass gains in the rhenium heaters. These mass gains were the result of the high amount of oxygen and water contained in the gas. Propellant purity and preferred test facility environments are discussed.

Whalen, M. V.↗

Compatibility experiments of facilities, materials, and propellants for electrothermal thrusters

Experiments were performed to determine the compatibility of materials and propellants for electro-thermal thrusters. Candidate propellants for resistojet propulsion include carbon dioxide, methane, hydrogen, ammonia, and hydrazine. The materials being examined are grain stabilized platinum for resistojets for space station and rhenium for high performance resistojets for satellites. Heater mass loss and deterioration of materials were evaluated. A coiled tube of platinum, with yttria dispersed throughout the base material to inhibit grain growth, was tested in carbon dioxide at 1300 C for 2000 hr. Post-test examination indicated the platinum-yttria heater would last over 100,000 hr with less than 10 percent mass loss. Short-term compatibility tests were conducted to test the integrity of the platinum-yttria in hydrogen, methane, carbon dioxide/methane mixtures and ammonia environments. In each of these 100 hr tests, the platinum-yttria mass change indicated a minimum coil life of 100,000 hr. Facility related effects were investigated in materials tests using rhenium heated to high temperatures. Vacuum facility water reduction was monitored using a mass spectrometer. In vacuum environments obtained using only diffusion pumping and those obtained with the assistance of cryogenic equipment there were mass gains in the rhenium heaters. These mass gains were the result of the high amount of oxygen and water contained in the gas. Propellant purity and preferred test facility environments are discussed.

Whalen, M. V.↗

Product assurance technology for custom LSI/VLSI electronics

The technology for obtaining custom integrated circuits from CMOS-bulk silicon foundries using a universal set of layout rules is presented. The technical efforts were guided by the requirement to develop a 3 micron CMOS test chip for the Combined Release and Radiation Effects Satellite (CRRES). This chip contains both analog and digital circuits. The development employed all the elements required to obtain custom circuits from silicon foundries, including circuit design, foundry interfacing, circuit test, and circuit qualification.

Buehler, M. G.↗

Results on reuse of reclaimed shower water

The Waste Water Recovery System that has been used in conjunction with a microgravity whole body shower to test a closed loop shower water reclamation system applicable to the NASA Space Station employs a Thermoelectric Integrated Hollow Fiber Membrane Evaporation Subsystem. Attention is given to the suitability of a Space Shuttle soap for such crew showers, the effects of shower water on the entire system, and the purification qualities of the recovered water. The chemical pretreatment of the shower water for microorganism control involved activated carbon, mixed ion exchange resin beds, and iodine bactericide dispensing units. The water was recycled five times, demonstrating the feasibility of reuse.

Verostko, Charles E.↗

Development and flight test experiences with a flight-crucial digital control system

Engineers and scientists in the advanced fighter technology integration (AFTI) F-16 program investigated the integration of emerging technologies into an advanced fighter aircraft. AFTI's three major technologies included: flight-crucial digital control, decoupled aircraft flight control, and integration of avionics, flight control, and pilot displays. In addition to investigating improvements in fighter performance, researchers studied the generic problems confronting the designers of highly integrated flight-crucial digital control. An overview is provided of both the advantages and problems of integration digital control systems. Also, an examination of the specification, design, qualification, and flight test life-cycle phase is provided. An overview is given of the fault-tolerant design, multimoded decoupled flight control laws, and integrated avionics design. The approach to qualifying the software and system designs is discussed, and the effects of design choices on system qualification are highlighted.

Mackall, Dale A.↗

Experimental and theoretical comparison of the Probe Thrust Vector Control concept

A concept that offers an alternate method for thrust vector control of liquid or solid propellant rockets is the use of a solid body or probe that is inserted on demand through the wall of the rocket nozzle. This Probe Thrust Vector Control (PTVC) concept is an alternative to that of a gimbaled nozzle or a Liquid Injection Thrust Vector control system. The viability of the PTVC concept can be assessed either experimentally and/or with the use of CFD. A purely experimental assessment is time consuming and expensive, whereas a CFD assessment is time- and cost-effective. Two key requirements of the concept are PTVC vectoring performance and active cooling requirements for the probe to maintain its thermal and structural integrity. The objective of the work reported here is presentation of experimental subscale cold flow tests and comparison of these tests with CFD predictions and the response time of the PTVC system.

Cavalleri, Robert↗

Plan for compensation of self-gravity on ST-7/DRS

The Space Technology 7 (ST-7) payload, flying on the Laser Interferometer Space Antenna (LISA) Pathfinder (LPF) mission, will demonstrate drag-free control of a test mass with acceleration disturbances below 3x10-14 m/s2/(square root)Hz. Low frequency acceleration noise introduced by the electrostatic force needed to counter static mass distribution imbalance is expected to be a significant contributor to the acceleration noise budget. For this reason, the self-gravity (due to mass imbalance) is minimized by adding trim mass to bring the total differential acceleration between the two test masses due to self-gravity below 5x10-10 m/s2 in any axis and the DC acceleration gradient due to self-gravity below 4x10-8 m/s2/m in any axis of either test mass. A plan has been established to develop the distribution and placement of the compensation masses. Compensation for the self-gravity effects on the two test masses is handled in a two step process. A nominal compensation mass is defined and incorporated early and is located very near the test masses. The final trimming for self-gravity occurs after the integration on the spacecraft with small mass added externally to the test mass vacuum enclosures. The plan identifies three preliminary points in the hardware maturity where the trimming to the as-built configuration can take place: (1) during build-up of the sensor vacuum enclosure, (2) prior to delivery of the integrated ST-7 to Europe, and (3) prior to environmental testing of the integrated LPF system. The sensitivity of the self-gravity to knowledge errors in the actual mass distribution is taken into account in the determination of final trimming opportunities and mounting locations.

acceleration noise↗

Integrated Simulation Design Challenges to Support TPS Repair Operations

During the Orbiter Repair Maneuver (ORM) operations planned for Return to Flight (RTF), the Shuttle Remote Manipulator System (SRMS) must grapple the International Space Station (ISS), undock the Orbiter, maneuver it through a long duration trajectory, and orient it to an EVA crewman poised at the end of the Space Station Remote Manipulator System (SSRMS) to facilitate the repair of the Thermal Protection System (TPS). Once repair has been completed and confirmed, then the SRMS proceeds back through the trajectory to dock the Orbiter to the Orbiter Docking System. In order to support analysis of the complex dynamic interactions of the integrated system formed by the Orbiter, ISS, SRMS, and SSMS during the ORM, simulation tools used for previous ‘nominal’ mission support required substantial enhancements. These upgrades were necessary to provide analysts with the capabilities needed to study integrated system performance. Prevalent throughout this ORM operation is a dynamically varying topology. In other words, the ORM starts with the SRMS grappled to the mated Shuttle/ISS stack (closed loop topology), moves to an open loop chain topology consisting of the Shuttle, SRMS, and ISS, and then, at the repair configuration, extends the chain topology to one consisting of the Shuttle, SMS, ISS, and SSRMS/EVA crewman. The resulting long dynamic chain of vehicles and manipulators may exhibit significant motion between the Shuttle worksite and the EVA crewman due to the system flexibility throughout the topology (particularly within the SRMS/SSRMS joints and links). Since the attachment points of both manipulators span the flexible structure of the ISS, simulation analysis may also need to take that into consideration. Moreover, due to the lengthy time duration associated with the maneuver and repair, orbital effects become a factor and require the ISS vehicle control system to maintain active attitude control. Several facets of the ORM operation make the associated analytical efforts different from previous mission support, including: (1) the magnitude of the SRMS handled payload (Le., Orbiter class), (2) the orbital effects induced on the integrated system consisting of the large Shuttle and ISS masses connected by a light flexible SRMS, (3) long duration environmental consequences due to the lengthy operational times associated with the maneuver and repair of the TPS, (4) active attitude control (as opposed to free drift) interacting with the SRMS and SSRMS manipulators (also due to the length of the maneuver and repair), (5) relative dynamics between the EVA crewman and thc worksite influenced by the extended flexible topology. In order to meet these analysis challenges, an ORM simulation architecture was developed leveraging upon numerous pre-existing simulation elements to analyze the various subsystems individually. For example, core manipulator subsystem simulations for both the SRMS and SSRMS were originally combined to provide the dual-arm dynamics topology simulation (in the absence of orbital dynamics and vehicle control). This capability was later merged with the simulation used to analyze SRMS loading with a heavy payload in the orbital environment with an active payload control system (in this case, the ISS Attitude Control System (ACS)), configured for the ORM. The resulting worksite dynamics simulation, based off of the modified ORM simulation, provided the extended topological chain of vehicles and manipulators, while taking into account the orbital effects of both the Shuttle and ISS (as well as its ACS). Verification and validation (V&V) of these integrated simulations became a challenge in itself. A systematic approach needed to be developed such that integration simulation results could be tested against previous constituent simulations upon which these simulations were built. General V&V categories included: (1) core orbital state propagation, (2), stand-alone SRMS, (3) stand-alone SSRMS, (4) stand-alone ISS ACS, (5) integrated Shuttle, SRMS, ISS (with active ACS) in the orbital environment, and (5) dual-arm SRMS/SSRMS dynamics topology. Integrated simulation V&V run suites were created and correlated to verification runs from subsystem simulations, in order to establish the validity of the results. This paper discusses the simulation design challenges encountered while developing simulation capabilities to mirror the ORM operations. The paper also describes the incremental build approach that was utilized, starting with the subsystem simulation elements and integration into increasing more complex simulations until the resulting ORM worksite dynamics simulation had been assembled. Furthermore, the paper presents an overall integrated simulation V&V methodology based upon a subsystem level testing, integrated comparisons, and phased checkout.

Thermal Protection System↗

NASA Dryden Status

This slide presentation reviews the status of several NASA Dryden projects. These include: the Lift And Nozzle Change Effects on Tail Shock (LANCETS), Integrated Resilient Aircraft Control (IRAC) F-18 #853 Testbed X-48B, Blended Wing Body flights, Stratospheric Observatory for Infrared Astronomy (SOFIA), Ikhana Project, and the Orion Crew Exploration Vehicle (CEV) Launch Abort Systems Tests

Bosworth, John T.↗

Detached Eddy Simulation Results for a Space Launch System Configuration at Liftoff Conditions and Comparison with Experiment

Computational simulations for a Space Launch System configuration at liftoff conditions for incidence angles from 0 to 90 degrees were conducted in order to generate integrated force and moment data and longitudinal lineloads. While the integrated force and moment coefficients can be obtained from wind tunnel testing, computational analyses are indispensable in obtaining the extensive amount of surface information required to generate proper lineloads. However, beyond an incidence angle of about 15 degrees, the effects of massive flow separation on the leeward pressure field is not well captured with state of the art Reynolds Averaged Navier-Stokes methods, necessitating the employment of a Detached Eddy Simulation method. Results from these simulations are compared to the liftoff force and moment database and surface pressure data derived from a test in the NASA Langley 14- by 22-Foot Subsonic Wind Tunnel.

Computational fluid dynamics↗

Test and Analysis of Full-Scale 27.5-Foot-Diameter Stiffened Metallic Launch Vehicle Cylinders

The Shell Buckling Knockdown Factor Project (SBKF) was established with the goal of developing improved (i.e., less-conservative, more robust) shell buckling knockdown factors (KDFs) for modern launch-vehicle structures. To this end, SBKF has engaged in several activities to support the development, validation, and implementation of the new design factors, including subscale and full-scale structural testing. Tests on eight different subscale, 8-foot-diameter, integrally stiffened aluminum-lithium 2195 (Al-Li 2195) cylinders were conducted in order to obtain the majority of the required validation data. In addition, two full-scale, 27.5-foot-diameter, Al-Li 2195, integrally stiffened cylinders were tested to provide additional validation data and to determine structural scaling trends. Presented herein are the details of a recent analysis model development and test and analysis correlation effort on the full-scale test articles. The effects of selected modeling assumptions and approaches are discussed, and results from a modeling sensitivity study are presented. It was found that simplified finite element models, that assume nominal test article geometry and material properties, can predict the overall response characteristics well. However, several discrepancies in the test and analysis results were observed. A sensitivity study was performed to determine the effects of several modeling assumptions and address the observed discrepancies. The results from the study indicated that the evolution of local skin pocket buckling and the presence of residual stresses due to the manufacturing process can have a significant influence on the predicted buckling response of the cylinders considered.

Lovejoy, Andrew E.↗