Search NASA⌕ Search

SEARCH · Search NASA

Results for “Propulsion System Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Experimental investigations of thrust vectoring systems for VTOL aircraft

This paper presents a summary of two technology programs sponsored by NASA to investigate the characteristics of two thrust vectoring schemes for V/STOL aircraft. The operational capability of the VTOL aircraft is dependent on maximum utilization of the installed thrust in both the cruise and powered lift modes of flight. An effective thrust vectoring system on the cruise propulsion unit is therefore essential to provide maximum payload in hover and STOL plus minimum specific fuel consumption in loiter and cruise. Introducing a high by-pass ratio fan system, augmenting the gas generator thrust, as the propulsion system for VTOL aircraft places increased significance on the performance of the relatively short coupled thrust vectoring systems. The two programs discussed herein include both large-scale and small-scale tests of a vectoring hood system with a vented, internal-lip and swivel nozzle systems. These tests indicated that a satisfactory thrust vectoring system can be developed.

Rolls, L. S.↗

Airflow and thrust calibration of an F100 engine, S/N P680059, at selected flight conditions

An airflow and thrust calibration of an F100 engine, S/N P680059, was conducted to study airframe propulsion system integration losses in turbofan-powered high-performance aircraft. The tests were conducted with and without thrust augmentation for a variety of simulated flight conditions with emphasis on the transonic regime. The resulting corrected airflow data generalized into one curve with corrected fan speed while corrected gross thrust increased as simulated flight conditions increased. Overall agreement between measured data and computed results was 1 percent for corrected airflow and -1 1/2 percent for gross thrust. The results of an uncertainty analysis are presented for both parameters at each simulated flight condition.

Biesiadny, T. J.↗

Altitude calibration of an F100, S/N P680063, turbofan engine

An airflow and thrust calibration of an F100 engine was conducted in coordination with a flight test program to study airframe-propulsion system integration characteristics of turbofan-powered high-performance aircraft. The tests were conducted with and without augmentation for a variety of simulated flight conditions with emphasis on the transonic regime. Test results for all conditions are presented in terms of corrected airflow and corrected gross thrust as functions of corrected fan speed for nonaugmented power and an augmented thrust ratio as a function of fuel-air ratio for augmented power. Comparisons of measured and predicted data are presented along with the results of an uncertainty analysis for both corrected airflow and gross thrust.

Biesiadny, T. J.↗

Space shuttle plume/simulation application: Results and math model supersonic data

The analysis of pressure and gage wind tunnel data from space shuttle wind tunnel test IA138 was performed to define the aerodynamic influence of the main propulsion system and solid rocket booster plumes on the total vehicles, elements, and components of the space shuttle vehicle during the supersonic portion of ascent flight. A math model of the plume induced aerodynamic characteristics was developed for a range of Mach numbers to match the forebody aerodynamic math model. The base aerodynamic characteristics are presented in terms of forces and moments versus attitude. Total vehicle base and forebody aerodynamic characteristics are presented in terms of aerodynamic coefficients for Mach numbers from 1.55 to 2.5.

Boyle, W.↗

Primary propulsion/large space system interactions

Three generic types of structural concepts and nonstructural surface densities were selected and combined to represent potential LSS applications. The design characteristics of various classes of large space systems that are impacted by primary propulsion thrust required to effect orbit transfer were identified. The effects of propulsion system thrust-to-mass ratio, thrust transients, and performance on the mass, area, and orbit transfer characteristics of large space systems were determined.

Dergance, R. H.↗

The Aerospace Vehicle Interactive Design system

The aerospace vehicle interactive design (AVID) is a computer aided design that was developed for the conceptual and preliminary design of aerospace vehicles. The AVID system evolved from the application of several design approaches in an advanced concepts environment in which both mission requirements and vehicle configurations are continually changing. The basic AVID software facilitates the integration of independent analysis programs into a design system where the programs can be executed individually for analysis or executed in groups for design iterations and parametric studies. Programs integrated into an AVID system for launch vehicle design include geometry, aerodynamics, propulsion, flight performance, mass properties, and economics.

Wilhite, A. W.↗

The Aerospace Vehicle Interactive Design system

The Aerospace Vehicle Interactive Design (AVID) is a computer-aided design system that was developed for the conceptual and preliminary design of aerospace vehicles. The AVID system evolved from the application of several design approaches in an advanced concepts environment in which both mission requirements and vehicle configurations are continually changing. The basic AVID software facilitates the integration of independent analysis programs into a design system where the programs can be executed individually for analysis or executed in groups for design iterations and parametric studies. Programs that have been integrated into an AVID system for launch vehicle design include geometry, aerodynamics, propulsion, flight performance, mass properties, and economics.

Wilhite, A. W.↗

Transonic wind tunnel test of a supersonic nozzle installation

The design of the propulsion system installation affects strongly the total drag and overall performance of an aircraft, and the concept, placement, and integration details of the exhaust nozzle are major considerations in the configuration definition. As part of the NASA Supersonic Cruise Research (SCR) program, a wind tunnel test program has been conducted to investigate exhaust nozzle-airframe interactions at transonic speeds. First phase testing is to establish guidelines for follow-on testing. A summary is provided of the results of first phase testing, taking into account the test approach, the effect of nozzle closure on aircraft aerodynamic characteristics, nozzle installation effects and nacelle interference drag, and an analytical study of the effects of nozzle closure on the aircraft.

Yetter, J. A.↗

Retooling CFD for hypersonic aircraft

The CFD facility requirements of hypersonic aircraft configuration design development are different from those thus far employed for reentry vehicle design, because (1) the airframe and the propulsion system must be fully integrated to achieve the desired performance; (2) the vehicle must be reusable, with minimum refurbishment requirements between flights; and (3) vehicle performance must be optimized for a wide range of Mach numbers. An evaluation is presently made of flow resolution within shock waves, transition and turbulence phenomenon tractability, chemical reaction modeling, and hypersonic boundary layer transition, with state-of-the-art CFD.

Dwoyer, Douglas L.↗

A flow-transfer device with nonmetallic diaphragms for propulsion wind tunnel models

The Langley Research Center has developed a new flow-transfer device for powered wind tunnel models in which the traditional metal bellows have been replaced with nonmetallic diaphragms. Two complete flow transfer assemblies have been fabricated and installed within a twin-jet propulsion simulation system. Calibrations of the force balance have been performed over a range of nozzle mass flow rates up to 15 lbs/sec in order to validate the nonmetallic diaphragm design concept. Results from these calibrations are compared to those obtained with flow-transfer devices utilizing metal bellows.

Capone, Francis J.↗

System design analyses of a rotating advanced-technology space station for the year 2025

Studies of an advanced technology space station configured to implement subsystem technologies projected for availability in the time period 2000 to 2025 is documented. These studies have examined the practical synergies in operational performance available through subsystem technology selection and identified the needs for technology development. Further analyses are performed on power system alternates, momentum management and stabilization, electrothermal propulsion, composite materials and structures, launch vehicle alternates, and lunar and planetary missions. Concluding remarks are made regarding the advanced technology space station concept, its intersubsystem synergies, and its system operational subsystem advanced technology development needs.

Queijo, M. J.↗

Knowledge-based network operations

An expert system for enhancing the operability of the ground communication element of the Jet Propulsion Laboratory's Deep Space Network is described. The system performs network fault management, configuration management, and performance management in real time. Extracted management information serves as input to the expert system and is used to update a management information data base. The monitor and control activities involve dividing software for each processor into layers which are each modeled as a finite state machine.

Wu, Chuan-Lin↗

Preliminary assessment of a supersonic STOVL flight research and demonstration aircraft

NASA Ames has conducted a conceptual design study of a supersonic short takeoff and vertical landing (STOVL) flight research and demonstration aircraft sized according to current technology levels. The aircraft would provide the capability for demonstrating advanced technologies required for STOVL and would be instrumented to provide temperature, pressure, and noise data for power-induced-effects research. The propulsion concept for the single-engine aircraft studied operates in mixed flow without thrust augmentation during power-lift flight. The study aircraft is full scale to facilitate STOVL propulsion-system component validation and power-induced aerodynamics research. Performance is sufficient to permit investigation and validation of vertical landing and hover, accelerating and decelerating transitions, short takeoff, reduced-weight vertical takeoff, and supersonic flight. Mission and maneuver capability is sufficient to demonstrate the operational utility of this class of aircraft. Aircraft mission and technology sensitivities were also examined.

Samuels, Jeffrey J.↗

High-temperature electronics

To meet the needs of the aerospace propulsion and space power communities, the high temperature electronics program at the Lewis Research Center is developing silicon carbide (SiC) as a high temperature semiconductor material. This program supports a major element of the Center's mission - to perform basic and developmental research aimed at improving aerospace propulsion systems. Research is focused on developing the crystal growth, characterization, and device fabrication technologies necessary to produce a family of SiC devices.

Matus, Lawrence G.↗

Enabler 1 and 2 engine system design modeling and comparisons

Viewgraphs on Enabler 1 and 2 engine system design modeling and comparisons are presented. The objective of this research was to define a near-term solid-core nuclear thermal propulsion (NTP) engine system scaling database. A unified set of performance, weight, and size scaling data are identified and documented. Results should be useful to meet initial mission and concept design study requirements.

Pelaccio, Dennis G.↗

Dynamic issues in launch vehicle design

Launch vehicles, in general, have been defined using performance requirements and generic payload characteristics which dictated the propulsion system and the payload carrier. The vehicle concept is then selected using these requirements in conjunction with basic criteria and standards. During the design phase, the selected concept must be modified in order to cope with the numerous dynamic and other problems that occur during design and development. This is costly and is, to some extent, unnecessary. The purpose of this paper is to propose an approach for bringing the dynamic issues into focus during concept selection, where the greatest payoff exists. Delaying consideration of the issues to the design phases creates many problems, not the least of which are the impacts levied against the payload community. Volumes of information exist from prior programs on these dynamic issues and serve as the guidelines for this paper.

Ryan, Robert S.↗

A comparison of paper and computer procedures in a Shuttle flight environment

The Electronic Procedures Experiment (EPROC) was flown as part of the Human Factors Assessment (HFA) experiment aboard the SpaceHab-1/STS-57 mission. EPROC is concerned with future, longer-duration missions which will increasingly rely on electronic procedures since they are more easily launched, updated in-flight, and offer automatic or on-request capabilities not available with paper. A computer-based task simulating a Space Station Propulsion System task was completed by one crewmember. The crewmember performed the task once using paper and once using computer procedures. A soldering and desoldering task was performed by another crewmember. Soldering was completed with paper procedures and desoldering was completed using computer procedures. Objective data was collected during each task session from the computer programs, videotapes, and crew notations in the paper and computer procedures. After each task session, subjective data was collected through the use of a computer-based questionnaire program. Resultant recommendations will be made available to future designers of electronic procedures systems for manned-space missions and other related uses.

Michael O'Neal↗

Direct drive options for electric propulsion systems

Power processing units (PPU's) in an electric propulsion system provide many challenging integration issues. The PPU must provide power to the electric thruster while maintaining compatibility with all of the spacecraft power and data systems. Inefficiencies in the power processor produce heat, which must be radiated to the environment in order to ensure reliable operation. Although PPU efficiencies are generally greater than 0.9, heat loads are often substantial. This heat must be rejected by thermal control systems which generally have specific masses of 15-30 kg/kW. PPU's also represent a large fraction of the electric propulsion system dry mass. Simplification or elimination of power processing in a propulsion system would reduce the electric propulsion system specific mass and improve the overall reliability and performance. A direct drive system would eliminate all or some of the power supplies required to operate a thruster by directly connecting the various thruster loads to the solar array. The development of concentrator solar arrays has enabled power bus voltages in excess of 300 V which is high enough for direct drive applications for Hall thrusters such as the Stationary Plasma Thruster (SPT). The option of solar array direct drive for SPT's is explored to provide a comparison between conventional and direct drive system mass.

Hamley, John A.↗