Search NASA⌕ Search

SEARCH · Search NASA

Results for “drying methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Dry-processed electrodes enabled by polytetrafluoroethylene fibrillation for high-performance lithium-ion batteries

The dry processing technique of polytetrafluoroethylene (PTFE) fibrillation offers significant advancements in cost reduction, environmental impact, and electrochemical performance. Dry processing alone allows for ∼ 20–60% cost reduction and increases of up to 40 mg cm⁻2 of areal loading – it typically comes at a reduction of rate capability. By leveraging the network structure of fibers, this method enhances rate capability and cycling performance, providing a compelling alternative to the conventional and currently predominant wet processing. The review delves into PTFE fibrillation mechanisms and examines critical influencing factors including material properties and processing parameters. It also discusses challenges associated with the electrodes fabricated by PTFE fibrillation, including structural instability due to insufficient PTFE fibrillization, compromised electrical conductivity from an insufficient conductive network, inhomogeneous dispersion resulting from the absence of solvents, restricted ionic transport due to increased electrode thickness, inadequate adhesion to current collector because of low surface energy of PTFE, electrochemical degradation due to low lowest unoccupied molecular orbital (LUMO) level of PTFE, particle damage during processing and environmental concerns related PTFE being a perfluoroalkyl and polyfluoroalkyl substances (PFAS). Recent research innovations aimed at mitigating these issues, their application in beyond-lithium batteries, and future research directions are thoroughly discussed.

Park, Hyunji↗

Mechanically tunable conductive interpenetrating network hydrogels that mimic the elastic moduli of biological tissue

Conductive and stretchable materials that match the elastic moduli of biological tissue (0.5–500 kPa) are desired for enhanced interfacial and mechanical stability. Compared with inorganic and dry polymeric conductors, hydrogels made with conducting polymers are promising soft electrode materials due to their high water content. Nevertheless, most conducting polymer-based hydrogels sacrifice electronic performance to obtain useful mechanical properties. Here we report a method that overcomes this limitation using two interpenetrating hydrogel networks, one of which is formed by the gelation of the conducting polymer PEDOT:PSS. Due to the connectivity of the PEDOT:PSS network, conductivities up to 23 S m-1 are achieved, a record for stretchable PEDOT:PSS-based hydrogels. Meanwhile, the low concentration of PEDOT:PSS enables orthogonal control over the composite mechanical properties using a secondary polymer network. We demonstrate tunability of the elastic modulus over three biologically relevant orders of magnitude without compromising stretchability ( > 100%) or conductivity ( > 10 S m-1 ).

36 MATERIALS SCIENCE↗

Additives for cement compositions based on modified peat

High quality competitive dry building mixes require modifying additives for various purposes to be included in their composition. There is insufficient amount of quality additives having stable properties for controlling the properties of cement compositions produced in Russia. Using of foreign modifying additives leads to significant increasing of the final cost of the product. The cost of imported modifiers in the composition of the dry building mixes can be up to 90% of the material cost, depending on the composition complexity. Thus, the problem of import substitution becomes relevant, especially in recent years, due to difficult economic situation. The article discusses the possibility of using local raw materials as a basis for obtaining dry building mixtures components. The properties of organo-mineral additives for cement compositions based on thermally modified peat raw materials are studied. Studies of the structure and composition of the additives are carried out by physicochemical research methods: electron microscopy and X-ray analysis. Results of experimental research showed that the peat additives contribute to improving of cement-sand mortar strength and hydrophysical properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of composite membranes of PVA-TEOS doped KOH for alkaline membrane fuel cell

Anion exchange membranes (AEMs) play an important role in separating fuel and oxygen (or air) in the Alkaline Membrane Fuel Cells. Preparation of hybrid organic inorganic materials of Polyvinylalcohol (PVA) - Tetraethylorthosilicate (TEOS) composite membrane doped KOH for direct alcohol alkaline fuel cell application has been investigated. The sol-gel method has been used to prepare the composite membrane of PVA-TEOS through crosslinking step and catalyzed by concentrated of hydrochloric acid. The gel solution was cast on the membrane plastic plate to obtain membrane sheets. The dry membranes were then doped by immersing in various concentrations of KOH solutions for about 4 hours. Investigations of the cross-linking process and the presence of hydroxyl group were conducted by FTIR as shown for frequency at about 1600 cm{sup −1} and 3300 cm{sup −1} respectively. The degree of swelling in ethanol decreased as the KOH concentration for membrane soaking process increased. The ion exchange capacity (IEC) of the membrane was 0.25meq/g. This composite membranes display significant ionic conductivity of 3.23 x 10{sup −2} S/cm in deionized water at room temperature. In addition, the morphology observation by scanning electron microscope (SEM) of the membrane indicates that soaking process of membrane in KOH increased thermal resistant.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Review on Binder Jet Additive Manufacturing of 316L Stainless Steel

Binder jet additive manufacturing enables the production of complex components for numerous applications. Binder jetting is the only powder bed additive manufacturing process that is not fusion-based, thus manufactured parts have no residual stresses as opposed to laser-based additive manufacturing processes. Binder jet technology can be adopted for the production of various small and large metallic parts for specific applications, including in the biomedical and energy sectors, at a lower cost and shorter lead time. One of the most well-known types of stainless steels for various industries is 316L, which has been extensively manufactured using binder jet technology. Binder jet manufactured 316L parts have obtained near full density and, in some cases, similar mechanical properties compared to conventionally manufactured parts. This article introduces methods, principles, and applications of binder jetting of SS 316L. Details of binder jetting processes, including powder characteristics (shape and size), binder properties (binder chemistry and droplet formation mechanism), printing process parameters (such as layer thickness, binder saturation, drying time), and post-processing sintering mechanism and densification processes, are carefully reviewed. Furthermore, critical factors in the selection of feedstock, printing parameters, sintering temperature, time, atmosphere, and heating rate of 316L binder jet manufactured parts are highlighted and summarized. Finally, the above-mentioned processing parameters are correlated with final density and mechanical properties of 316L components to establish a guideline on feedstock selection and process parameters optimization to achieve desired density, structure and properties for various applications.

36 MATERIALS SCIENCE↗

Computations of transmittance and radiance in infrared water vapor sounding channels

The wing-scaling approximation/k-distribution method, previously developed for computing solar heating rates (Chou and Arking, 1981) was applied to the computation of the transmittance and outgoing radiance in infrared water vapor sounding channels. Functions necessary for the transmittance and radiance computations were computed from molecular line parameters using line-by-line methods. The method was applied to the three HIRS/2 water vapor sounding channels on the TIROS-N satellite, and its accuracy was tested using 11 widely separated atmospheres which ranged from hot-wet tropical atmospheres to cold-dry subarctic atmospheres. Compared to line-by-line calculations, maximum errors were shown to be less than 0.017 in transmittance and 0.4 K in brightness temperature for all cases. The rms errors are less than 0.009 in transmittance and 0.2 K in brightness temperature, the brightness temperature rms error being much smaller than the instrument noise.

Chou, M.-D.↗

Aqueous cleaning design presentation

The phase-out of CFC's and other ozone depleting chemicals has prompted industries to re-evaluate their present methods of cleaning. It has become necessary to find effective substitutes for their processes as well as to meet the new cleaning challenges of improved levels of cleanliness and to satisfy concerns about environmental impact of any alternative selected. One of the most popular alternatives being selected is aqueous cleaning. This method offers an alternative for removal of flux, grease/oil, buffing compound, particulates and other soils while minimizing environmental impact. What I will show are methods that can be employed in an aqueous cleaning system that will make it environmentally friendly, relatively simple to maintain and capable of yielding an even higher quality of cleanliness than previously obtained. I will also explore several drying techniques available for these systems and other alternatives along with recent improvements made in this technology. When considering any type of cleaning system, a number of variables should be determined before selecting the basic configuration. Some of these variables are: (1) Soil or contaminants being removed from your parts; (2) The level of cleanliness required; (3) The environmental considerations of your area; (4) Maintenance requirements; and (5) Operating costs.

Maltby, Peter F.↗

Chemical sensor system

A chemical sensing apparatus and method for the detection of sub parts-per-trillion concentrations of molecules in a sample by optimizing electron utilization in the formation of negative ions is provided. A variety of media may be sampled including air, seawater, dry sediment, or undersea sediment. An electrostatic mirror is used to reduce the kinetic energy of an electron beam to zero or near-zero kinetic energy.

Darrach, Murray R.↗

Wildland Fires in the Subtropical Hill Forests of Southeastern Bangladesh

The first ever comprehensive study on wildland fires in Bangladesh is carried out to develop a fire prevention and prediction method. The major causes of huge wildland fires (88%) in the subtropical Chittagong Hill forest (43% of total) of southern Bangladesh are reported as shifting cultivation, grazing and unauthorized settlement. We used satellite hotspot (HS) data from 2003 to 2021 (a total of 54,669 HSs) to clarify the spatio-temporal structure of wildland fires. Fire weather conditions were analyzed using various weather data and synoptic-scale weather maps at different air levels. Fires concentrated from March through April or a transitional period from the dry season, caused by the Asian winter monsoon, to the wet season, due to the Asian summer monsoon. Fire occurrence depended on dry conditions and pre-monsoon showers and their timing. The difference in 925 hPa heights of high and low pressure systems may be attributed to the different types of the Asian winter and summer monsoons. The average maximum air temperature and incident shortwave solar energy in April were the highest and strongest, contributing fire-prone weather conditions. Based on the analysis, a fire prevention and prediction method will be developed, and this report may also facilitate the establishment of future CO 2 reduction measures for Bangladesh.

54 ENVIRONMENTAL SCIENCES↗

Continuous fabrication system and method for highly aligned polymer films

Process for continuous fabrication of highly aligned polymer films. A polymer-solvent solution is subjected to a high shear, high temperature, Couette flow to extrude a thin film having polymer chain disentanglement. The extruded thin film is frozen and the solvent is allowed to evaporate to form a dried film. The dried film is mechanically drawn using a constant force, adaptive-thickness drawing system to align polymer molecular chains through plastic deformation. A suitable polymer is ultra-high molecular weight polyethylene.

36 MATERIALS SCIENCE↗

Reflow-oven-processing of pressureless sintered-silver interconnects

Here, a method was developed to pressurelessly fabricate strong and consistent sinterable-silver joints or interconnects using reflow oven heating. Circular sinterable-silver interconnects, having nominal diameter of 5 mm and 0.1 mm thickness were stencil printed, contact-dried, and then pressurelessly sinter-bonded to Au-plated direct copper bonded ceramic substrates at 250 °C in ambient air. That sintering was done in either a reflow oven or a convective oven (latter being a conventional heating source for processing sinterable-silver). Consistently strong (>40 MPa) interconnects were produced with reflow oven heating and were as strong as those produced with convective oven heating. This is significant because reflow oven technology affords better potential for continuous mass production and it was shown that strong sintered-silver bonds can indeed be achieved with its use.

36 MATERIALS SCIENCE↗

The characterization of wear-causing particles and silica sand in particular

Erodants and abradants are two types of wear-causing particles (WCP). Despite their effects on the severity and rate of wear, WCP are inadequately characterized in a surprising number of publications, especially those involving impingement erosion and three-body abrasion. That shortfall makes it difficult to correlate features of WCP with the details of worn surfaces, or to develop wear models that account for those features. It is argued that the documentation of WCP should go beyond simply reporting their composition and mean particle size. In late 1985, ASTM Committee G2 on Wear and Erosion established a task group on the characterization of WCP. At that time, image analysis was slower and less sophisticated than it is today. While that ASTM task group failed to produce a consensus standard, computerized particle characterization methods were developing in fields other than tribology, fields like geoscience, heavy sand mining, materials processing, and pharmaceuticals. A notable exception to this is ferrography, which is a widely-used diagnostic for lubricated tribosystems. In the context of dry wear, it is useful to identify which features of WCP would be beneficial to document, and to identify some techniques and scales of detail appropriate to particular tribosystems. In this paper, examples are presented for the morphological and mechanical characterization of silica sand grains, as prompted by a triboanalysis of the abrasive and erosive wear of biomass pre-processing equipment. The authors propose a minimum level of documentation for WCP, one that can enrich tribosystem analysis both in laboratory tests and field studies.

36 MATERIALS SCIENCE↗

Photo-Swing CO2 Capture Using a Branched Polyethylenimine As Sorbents and TiN Light Absorber

Using branched polyethylenimine as the sorbent material for dilute CO2 capture, a photo-swing method is demonstrated in an industrially relevant support architecture using titanium nitride (TiN) nanosized light absorbers coupled with low-power LEDs with irradiances up to 420 mW cm-2. The photo-swing desorption process is applied to dry and humid streams of 400 ppm CO2 diluted in N2. Consistent with known sorption mechanisms for aminopolymers, humid CO2 streams increased the CO2 uptake, in our case by ~30%. The photo-swing CO2 capture desorbed ~83% and ~100% CO2 compared to thermally-driven desorption over the same period for a dry and humid CO2 stream, respectively. The photo-swing CO2 capture exhibits robust performance over >90 cycles without significant signs of photo(thermal) induced sorbent degradation. This work lays the groundwork for photo-swing DAC technology as a scalable, energy-efficient solution for CO2 capture, well-suited for modular systems in remote locations utilizing intermittent renewable energy sources.

36 MATERIALS SCIENCE↗

Electrokinetics of scalable, electric-field-assisted fabrication of vertically aligned carbon-nanotube/polymer composites

Composite thin films incorporating vertically aligned carbon nanotubes (VACNTs) offer promise for a variety of applications where the vertical alignment of the CNTs is critical to meet performance requirements, e.g., highly permeable membranes, thermal interfaces, dry adhesives, and films with anisotropic electrical conductivity. However, current VACNT fabrication techniques are complex and difficult to scale up. In this paper, we describe a solution-based, electric-field-assisted approach as a costeffective and scalable method to produce large-area VACNT composites. Multiwall-carbon nanotubes are dispersed in a polymeric matrix, aligned with an alternating-current (AC) electric field, and electrophoretically concentrated to one side of the thin film with a direct-current (DC) component to the electric field. This approach enables the fabrication of highly concentrated, individually aligned nanotube composites from suspensions of very dilute (Φ=4×10 –4 ) volume fraction. We experimentally investigate the basic electrokinetics of nanotube alignment under AC electric fields, and show that simple models can adequately predict the rate and degree of nanotube alignment using classical expressions for the induced dipole moment, hydrodynamic drag, and the effects of Brownian motion. The composite AC þ DC field also introduces complex fluid motion associated with AC electro-osmosis and the electrochemistry of the fluid/electrode interface. We experimentally probe the electric-field parameters behind these electrokinetic phenomena, and demonstrate, with suitable choices of processing parameters, the ability to scalably produce large-area composites containing VACNTs at number densities up to 10 10 nanotubes/cm 2 . This VACNT number density exceeds that of previous electric-fieldfabricated composites by an order of magnitude, and the surface-area coverage of the 40nm VACNTs is comparable to that of chemical-vapor-deposition-grown arrays of smaller-diameter nanotubes.

42 ENGINEERING↗

Interactions between urban heat islands and heat waves

Heat waves (HWs) are among the most damaging climate extremes to human society. Climate models consistently project that HW frequency, severity, and duration will increase markedly over this century. For urban residents, the urban heat island (UHI) effect further exacerbates the heat stress resulting from HWs. Here we use a climate model to investigate the interactions between the UHI and HWs in 50 cities in the United States under current climate and future warming scenarios. We examine UHI 2m (defined as urban-rural difference in 2m-height air temperature) and UHI s (defined as urban-rural difference in radiative surface temperature). Our results show significant sensitivity of the interaction between UHI and HWs to local background climate and warming scenarios. Sensitivity also differs between daytime and nighttime. During daytime, cities in the temperate climate region show significant synergistic effects between UHI and HWs in current climate, with an average of 0.4 K higher UHI 2m or 2.8 K higher UHI s during HWs than during normal days. These synergistic effects, however, diminish in future warmer climates. In contrast, the daytime synergistic effects for cities in dry regions are insignificant in the current climate, but emerge in future climates. At night, the synergistic effects are similar across climate regions in the current climate, and are stronger in future climate scenarios. We use a biophysical factorization method to disentangle the mechanisms behind the interactions between UHI and HWs that explain the spatial-temporal patterns of the interactions. Results show that the difference in the increase of urban versus rural evaporation and enhanced anthropogenic heat emissions (air conditioning energy use) during HWs are key contributors to the synergistic effects during daytime. The contrast in water availability between urban and rural land plays an important role in determining the contribution of evaporation. At night, the enhanced release of stored and anthropogenic heat during HWs are the primary contributors to the synergistic effects.

54 ENVIRONMENTAL SCIENCES↗

Polarized 3He gas circulating technologies for neutron analyzers

We outline our project to develop a circulating polarized helium-3 system for developing of large, quasi-continuously operating neutron analyzers. The project consisted of four areas: 1) Development of robust external cavity narrowed diode laser output with spectral line width < 0.17 nm and power of 2000 W. 2) Development of large glass polarizing cells using cell surface treatments to obtain long relaxation lifetimes. 3) Refinements of the circulation system with an emphasis on gas purification and materials testing. 4) Design/fabrication of a new polarizer system. 5) Preliminary testing of the new polarizer. 1. Developed Robust High-Power Narrowed Laser The optical configuration of the laser was discussed in the proposal and will be reviewed in the body of this report. The external cavity is configured to mutually lock the wavelength of five 10-bar laser stacks. All the logistical milestones were been met and critical subsystems- laser stack manifold and power divider, external laser cavity, and output telescope- were assembled and tested at low power. Each individual bar is narrowed to ~0.05 nm; when combined the laser has a cumulative spectral width of 0.17 nm across the entire beam due to variations of the bars central wavelength by +/- 0.1 nm, which is similar to that of Volume Bragg Grating narrowed laser bars. This configuration eliminates the free-running “pedestal” that occurs in other external cavity diode lasers. The full-scale laser was completed in 2016 and was used in both the older and newer helium polarizers. This laser was operated at 75% power for periods of up to 8 hours. Once installed, the spectrum became slightly broader (~.25 nm) at full power; this is likely due to very slight misalignments that occurred during handling. 2. Developed the processes to create uniform sintered sol-gel coatings. Our work on cell development comprised: 1) Production of large GE180 cells and explore different means of cell preparation, and 2) Development of apply sol-gel coatings to the interior of both borosilicate and aluminosilicate cells. We applied six sol-gel coatings. By modifying the mixture and developing procedures to drain and dry the cell, we produced visually uniform coatings on the interior of the cells. We now have perfected that process as described below in our report. We were able to accelerate the testing of cells using an ex situ method that avoids installing each cell into a polarizer. In the project’s last year, we conducted 38 external tests of 8 different cells. We also installed two sol-gel coated cells in our polarizers. We created cell with long ex situ relaxation lifetimes, one of which exceeded 40 hours. However, when installed in the polarizer the measured lifetime is 8 hours or less. 3. Demonstrated cycling of polarized gas and ex situ cell testing We are now cycling polarized gas from the polarizer to glass vessels and back. This has allowed us, for the first time, to make ex situ T1 measurements of polarizing cells without installing them into the polarizer itself. This has greatly improved our productivity in producing cells and evaluating our cell preparation processes. We continued development of the gas handling system in parallel with fabricating new polarizer. The integrated system was tested by the end of 2016. We now regularly cycle gas into and out of the polarizer. 4. Completed new polarizer infrastructure and control systems. We completed the new polarizer infrastructure in November 2016. The polarizer subsystems are 1) the frame, 2) the oil flow system, 3) the gas handling system, 4) the pressure vessel, with embedded solenoid, 5) cell mounting hardware with heat spreaders, and 6) electrical power and instrumentation. 5. Carried out initial tests of polarizer. We completed initial testing of the polarizer in April and May of 2017. These tests were carried out for periods up to 6 hours with laser power between 750 and 1300 Watts. The laser performed well and the polarization with asymptotic to 45 percent, which was below expectations. This low value resulted from a stationary thermal inversion in the cell that caused most of the laser power to be absorbed near the laser inlet window and deprived the lower portions of the cell of pumping laser light. Possible solutions to this problem include enhanced cooling of the cell near the laser entry and slight detuning of the laser. 6. Ongoing work. Our polarizer development efforts are ongoing to pursue our interest in neutron analyzers, nuclear targets, and providing helium for medical imaging. Current tests in the pipeline include: 1. Testing cooling enhancements to improve laser penetration of spectrally narrow lasers; 2. Testing of a cell with isolation valves that minimizes diffusive contact with gas handling hardware during polarization; 3. Testing of smaller hybrid cells with reduced alkali loading; 4. Producing polarized helium-3 for MRI imaging at the University of Missouri.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Evaluation of Neutron Absorbers in the DOE Standardized SNF Canister

The goal of this evaluation was to evaluate different options for a neutron absorber in the U.S. Department of Energy (DOE) Standardized spent nuclear fuel (SNF) Canister. This was accomplished by taking the two most relevant criticality evaluations and replacing the advanced neutron absorber (ANA) basket material with borated stainless steel. This work was initiated, because alternative storage options for DOE SNF has become a priority for DOE. Idaho National Laboratory (INL) is initiating activities to ensure the continued operation of the Advanced Test Reactor (ATR) by providing alternative and redundant storage options for spent ATR fuel. In addition, the DOE Office of Environmental Management (EM) has recently initiated studies to understand and improve the technical basis for long-term dry storage of aluminum clad SNF (e.g., ATR, High Flux Isotope Reactor [HFIR]) (Connolly 2018). While currently in the lab-scale phase, the next step involves validation and verification (V&V) of the lab-scale results. One method to perform V&V is to load aluminum-clad spent fuel in an instrumented DOE Standardized SNF Canister as a demonstration. In order to minimize the need for repackaging before disposal and to provide a representative environment in a demonstration, the fuel is planned to be loaded with an appropriate criticality control mechanism, such as neutron absorbing basket material. While ANA was originally selected as the basket material for ATR fuel in the Yucca Mountain Repository, it has never been produced on a large scale. Therefore, incorporating this material in the DOE Standardized SNF Canister as part of a near-term demonstration could be more challenging than moving forward with a commercially available material, such as borated stainless steel. Past evaluations eliminated borated stainless steel as a long-term neutron absorbing material, because it corroded too quickly and may not always remain in the waste package after degradation. This led to the invention and selection of ANA for use as the basket material in the DOE Standardized SNF Canister. After selecting ANA, new corrosion tests were performed on borated stainless steel using a different method for fabrication. This method of fabrication significantly improved the corrosion resistance properties of borated stainless steel, so much so that it out-performed ANA in corrosion testing. Researchers used the information obtained from these tests to select borated stainless steel as the neutron absorber in the Transportation, Aging, and Disposal Canister (TAD) designed for commercial SNF. This evaluation compares the criticality control of borated stainless steel to ANA. In every case and scenario, the calculated effective neutron multiplication factor (k eff ) using a borated stainless steel basket was lower than that using an ANA basket, though the borated stainless steel must be thicker due to corrosion effects over the regulatory time period. Although the borated stainless steel performed better than the ANA, it still required additional neutron-absorbing material, gadolinium shot, for the calculated k eff to fall below the upper critical limit of 0.93 in a few cases evaluated. More research using thicker baskets or inserts could be performed in an attempt to lower the k eff without the use of gadolinium shot. In addition, a reevaluation of the degraded ATR material used in the previous evaluations may prove that the original assumptions were over-conservative.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Nucleic acid hybridization with RNA immobilized on filter paper.

RNA has been immobilized in a manner suitable for use in molecular hybridization experiments with dissolved RNA or DNA by a nonaqueous solid-phase reaction with carbonyldiimidazole and RNA 'dry coated' on cellulose or, preferably, on previously activated phosphocellulose filters. Immobilization of RNA does not appear to alter its chemical character or cause it to acquire affinity for unspecific RNA or DNA. The versatility and efficiency of this method make it potentially attractive for use in routine analytical or preparative hybridization experiments, among other applications.

Saxinger, W. C.↗