Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructural organization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Experimental and theoretical evidence for hydrogen doping in polymer solution-processed indium gallium oxide

The field-effect electron mobility of aqueous solution-processed indium gallium oxide (IGO) thin-film transistors (TFTs) is significantly enhanced by polyvinyl alcohol (PVA) addition to the precursor solution, a >70-fold increase to 7.9 cm 2 /Vs. To understand the origin of this remarkable phenomenon, microstructure, electronic structure, and charge transport of IGO:PVA film are investigated by a battery of experimental and theoretical techniques, including In K-edge and Ga K-edge extended X-ray absorption fine structure (EXAFS); resonant soft X-ray scattering (R-SoXS); ultraviolet photoelectron spectroscopy (UPS); Fourier transform-infrared (FT-IR) spectroscopy; time-of-flight secondary-ion mass spectrometry (ToF-SIMS); composition-/processing-dependent TFT properties; high-resolution solid-state 1 H, 71 Ga, and 115 In NMR spectroscopy; and discrete Fourier transform (DFT) analysis with ab initio molecular dynamics (MD) liquid-quench simulations. The 71 Ga{ 1 H} rotational-echo double-resonance (REDOR) NMR and other data indicate that PVA achieves optimal H doping with a Ga···H distance of ~3.4 Å and conversion from six- to four-coordinate Ga, which together suppress deep trap defect localization. This reduces metal-oxide polyhedral distortion, thereby increasing the electron mobility. Finally, hydroxyl polymer doping thus offers a pathway for efficient H doping in green solvent-processed metal oxide films and the promise of high-performance, ultra-stable metal oxide semiconductor electronics with simple binary compositions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Review of the Effects of Polymer Binder Properties on Microstructure and Irreversible Volume Growth of Plastic Bonded Explosives Formulations

The rational design of effective polymeric binders for the formulation of plastic-bonded explosives (PBX) is challenging due to their inherent compositional complexity. The composites comprise irregularly shaped energetic material (EM) powders coated with low weight fractions of polymer via non-equilibrium processes such as slurry coating. Defects can deleteriously affect PBX stability and performance: nano- to micrometer-scale voids can act as loci for hot spots, lowering deflagration and detonation temperatures in unpredictable ways. Furthermore, some nominally desirable polymer properties are at odds with each other: e. g. good flow characteristics are desirable for coating and adhesion, but mechanical stiffness is needed to prevent deformation and cracking of PBX under mechanical stress. Good binder adhesion is critical, but the best means to predict and measure adhesion in PBX is not obvious. Experimental methods of determining binder adhesion on model surfaces may not capture polymer structural configurations relevant to deposition during coating. Molecular dynamics-based computational models have predicted key observables in PBX formulation, suggesting that they may be powerful tools for binder selection. In this review, primarily recent (~2006 and later) literature on polymeric binders for insensitive HE (IHE) is surveyed. We focus on how binder properties influence observable PBX properties as resistance to irreversible volume growth and void formation in PBX formulations mainly (but not exclusively) featuring 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) as the EM (e. g. PBX 9502, LX-17 and others). Conclusions from these studies yield useful guidelines for choosing HE binder candidates, as well as for the general design of highly-filled polymer composite materials. Finally, studies describing challenges in PBX formulation with the newer and more energetically dense high explosive, LLM-105, will be discussed.

adhesion↗

Effect of Macro- and Microstructures on Catalytic Hydrogenolysis of Polyolefins

Here, polyethylenes of varying molecular weight and branch density, as well as polypropylenes of varying molecular weight and tacticity, were catalytically converted to lower-molecular-weight liquid products to showcase how these various properties in a mixed waste plastic stream could affect the final product. A Pt nanoparticle on a strontium titanate nanocuboid (Pt/STO) catalyst was used under solvent-free conditions in the presence of 170 psi of H 2 at 300 °C for hydrogenolysis. The initial molecular weight of polyethylene was found to have a moderate effect on the yield to the final product (ranging from 55 wt% for M n ~ 7600 Da to 67 wt% for M n ~ 50,950 Da). The microstructure, defined as the length and density of branches in a polymer, of higher-molecular-weight polymers was the dominant factor in determining the yield (ranging from 67 wt% for M n ~ 50,950 Da for linear low-density polyethylene (LLDPE) with C 2 branches to 97 wt% for M n ~ 38,850 Da for LLDPE with C 6 branches). The same products (M n = C 29 –C 46 , Ð = 1.1–1.6) and distribution of undesired light gases (C 1 –C 4 ≈ 90 mol%, C 5 –C 8 ≈ 10 mol%) are obtained from conversions of PE of varying molecular weight. The tacticity of polypropylene at a given molecular weight had a significant effect on the molecular weight of the final product, while not strongly affecting conversion. Hydrogenolysis of isotactic polypropylene (iPP) produced ≈C 18 with a wider polydispersity (Ð ~ 1.4) compared to the narrow ≈C 64 (Ð ~ 1.0) and ≈C 54 (Ð ~ 1.0) products from atactic (aPP) and syndiotactic (sPP) polypropylene, respectively. The stereochemistry of the methyl groups dictates the shape and structure of the polymer in the melt, which in turn affects how the hydrocarbon chain interacts with the catalyst surface, thereby impacting the number of C–C scissions. These results show how various characteristics such as the molecular weight and structure of a waste plastic stream could affect the final product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Discordant nature of Cd in PbSe: off-centering and core–shell nanoscale CdSe precipitates lead to high thermoelectric performance

We report a novel hierarchical microstructure in the PbSe–CdSe system, which collectively contributes to significant enhancement in thermoelectric performance, with ZT ave ~ 0.83 across the 400–923 K temperature range, the highest reported for p-type, Te-free PbSe systems. We have investigated the local atomic structure as well as the microstructure of a series of PbSe–xCdSe materials, up to x = 10%. We find that the behavior of the Cd atoms in the octahedral rock salt sites is discordant and results in off-center displacement and distortion. Such off-centered Cd in the PbSe matrix creates (1) L–Σ electronic energy band convergence, (2) a flattened L band, both contributing to higher Seebeck coefficients, and (3) enhanced phonon scattering, which leads to lower thermal conductivity. These conclusions are supported by photoemission yield spectroscopy in air (PYSA), solid state 111 Cd, 77 Se NMR spectroscopy and DFT calculations. Above the solubility limit (>6%CdSe), we also observe endotaxial CdSe nano-precipitates with core–shell architecture formed in PbSe, whose size, distribution and structure gradually change with the Cd content. The nano-precipitates exhibit a zinc blende crystal structure and a tetrahedral shape with significant local strain, but are covered with a thin wurtzite layer along the precipitate/matrix interface, creating a core–shell structure embedded in PbSe. This newly discovered architecture causes a further reduction in lattice thermal conductivity. Furthermore, potassium is found to be an effective p-type dopant in the PbSe–CdSe system, leading to an enhanced power factor, a maximum ZT of ~1.4 at 923 K for Pb 0.98 K 0.02 Se–6%CdSe.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental Insights into the Coupling of Methane Combustion and Steam Reforming in a Catalytic Plate Reactor in Transient Mode

The microstructured reactor concept is very promising technology to develop a compact reformer for distributed hydrogen generation. In this work, a catalytic plate reactor (CPR) is developed and investigated for the coupling of methane combustion (MC) and methane steam reforming (MSR) over Pt/Al 2 O 3 -coated microchannels in cocurrent and counter-current modes in transient experiments during start-up. A three-dimensional (3D) computational fluid dynamics (CFD) simulation shows uniform velocity and pressure distribution profiles in microchannels. For a channel velocity from 5.1 to 57.3 m/s in the combustor, the oxidation of methane is complete and self-sustainable without explosion, blow-off, or extinction; nevertheless, flashbacks are observed in counter-current mode. In the reformer, the maximum methane conversion is 84.9% in cocurrent mode, slightly higher than that of 80.2% in counter-current mode at a residence time of 33 ms, but at the cost of three times higher energy input in the combustor operating at ~1000 °C. Nitric oxide (NO) is not identified in combustion products, but nitrous oxide (N 2 O) is a function of coupling mode and forms significantly in cocurrent mode. Furthermore, this research would be helpful to establish the start-up strategy and environmental impact of compact reformers on a small scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Scale Invariance of Hot Spot Formation in TATB High Explosives

Shock-induced detonation of insensitive high explosives based on 1,3,5-triamino-2,4,6-trinitrobenzene starts with formation of hot spots at microstructural defects but has eluded atomistic modeling treatment at micron length scales. To this end, we performed multimicron scale all-atom molecular dynamics (MD) simulations of hot spots that form during the collapse of cylindrical pores with diameters between 10 and 300 nm. Our MD simulations show that hot spots formed at pores larger than 20 nm exhibit temperature fields with scale-invariant features for sizes up to at least 300 nm. Through a continuum-based grain-scale modeling framework, we span and extend beyond the size scales currently accessible to MD and find that hot spot scale invariance is a general feature that arises when the mechanical strength is insensitive to strain rate. Finally, our results demonstrate the applicability of all-atom MD to simulate the complicated dynamical evolution of micron-sized systems and bolster confidence in insights from MD simulations of materials that exhibit strength with negligible rate dependence over the relevant intervals.

36 MATERIALS SCIENCE↗

In Situ Study of Particle Precipitation in Metal-Doped CeO2 during Thermal Treatment and Ion Irradiation for Emulation of Irradiating Fuels

Metallic particles formed in oxide fuels (e.g., UO 2 ) during neutron irradiation have an adverse impact on fuel performance. A fundamental investigation of particle precipitation is needed to predict the fuel performance and potentially improve fuel designs and operations. In this study, we report on the precipitation of Mo-dominant β-phase particles in polycrystalline CeO 2 (surrogate for UO 2 ) films doped with Mo, Pd, Rh, Ru, and Re (surrogate for Tc). In situ heating scanning transmission electron microscopy indicates that particle precipitation starts at ~1073 K with a limited particle growth to ~10 nm. While particle concentration increases with increasing temperature, particle size remains largely unchanged up to 1273 K. There is a dramatic change in the microstructure following vacuum annealing at 1373 K, probably due to phase transition of reduced cerium oxide. At the high temperature, particles grow up to 75 nm or larger with distinctive facets. The particles are predominantly composed of Mo with a body-centered cubic structure (β phase). An oxide layer was observed after storage at ambient conditions. In situ heating X-ray photoelectron spectroscopy reveals an increasing reduction of Ce charge state from 4+ to 3+ in the doped CeO 2 film at temperatures from 673 to 1273 K. In situ ion irradiation transmission electron microscopy with 2 MeV Al 2+ ions up to a dose of ~20 displacements per atom at nominally room temperature does not lead to precipitation of visible particles. However, irradiation with 1.7 MeV Au 3+ ions to ~10 dpa at 973 K produces ~2 nm sized pure Pd particles; Au 3+ irradiation at 1173 K appears to result in precipitates of ~6 nm in size. Some of the defects produced by ion irradiation could be nucleation sites for precipitation, leading to generation of smaller particles with a higher concentration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

One-Step Synthesis and Operando Electrochemical Impedance Spectroscopic Characterization of Heterostructured MoP–Mo 2 N Electrocatalysts for Stable Hydrogen Evolution Reaction

Here this study presents a novel synthesis of self-standing MoP and Mo 2 N heterostructured electrocatalysts with enhanced stability and catalytic performance. Facilitated by the controlled phase and interfacial microstructure, the seamless structures of these catalysts minimize internal resistivity and prevent local corrosion, contributing to increased stability. The chemical synthesis proceeds with etching step to activate the surface, followed by phosphor-nitriding in a chemical vapor deposition chamber to produce MoP-Mo 2 N@Mo heterostructured electrocatalysts. X-ray diffraction analyses confirm the presence of MoP, Mo 2 N, and Mo phases in the electrocatalyst. Morphology studies using scanning electron microscopy characterizes the hierarchical growth of structures, indicating successful formation of the heterostructure. X-ray photoelectron spectroscopy (XPS) analyses of the as-synthesized and post-catalytic activity samples reveal the chemical shift in terms of binding energy (BE) of Mo 3d XPS peak, especially after catalytic activity. The XPS BE shifts attributed to changes in oxidation state, electron transfer, and surface reconstruction during catalysis. Electrochemical evaluation of the catalysts demonstrates the superior performance of the MoP-Mo 2 N@Mo heterostructured catalyst in hydrogen evolution reactions (HER), with lower overpotentials and enhanced Tafel slopes. Stability tests reveal changes in double layer capacitance over time, suggesting surface reconstruction and increased active surface area during catalysis. Operando electrochemical impedance spectroscopy (EIS) further elucidates the dynamic changes in resistance and charge transfer during HER. Overall, comprehensive understanding of the synthesis, characterization, and electrochemical behavior of the developed MoP-Mo 2 N@Mo heterostructured electrocatalyst as presented in this paper highlights their potential utilization in sustainable energy applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mechanisms of Zn removal from water by amorphous geopolymer: Molecular-level insights from X-ray absorption spectroscopy, isotope fractionation, and surface complexation modeling

Porous geopolymers have attracted widespread attention as promising heavy metal adsorbents that can be synthesized from aluminosilicate solid wastes. However, the precise microstructural evidence for adsorbed heavy metals on geopolymers remains unclear due to the insensitivity of conventional characterization techniques on minerals with amorphous structure and surface disorder. Batch adsorption and column experiments coupled with X-ray absorption spectroscopy (XAS), Zn stable isotope, and surface complexation model (SCM) were employed to reveal the Zn removal mechanisms with coal fly ash porous geopolymer (CFAPG) at a molecular scale. The macroscopic kinetic and isothermal adsorption of Zn on CFAPG were well described by the pseudo-second-order model and Bi_Langmuir equation, respectively, indicating the presence of abundant heterogeneous active sites on the CFAPG surface. Further, two types of active sites on the CFAPG surface were identified by XAS coupled with Zn isotopes in batch experiments at pH <= 6.0: one is pH-dependent and associated with tetrahedral zinc coordi-nation, and the other is pH-insensitive and associated with octahedral zinc coordination; these sites were confirmed by the bidentate SCM as the variable charge site (surface complexation, >S-OH) and the permanent negative charge site (cation exchange, >X - ), respectively. Furthermore, the important contribution of surface co -precipitation besides surface complexation and cation exchange to the Zn adsorption on CFAPG was identified by XAS coupled with SCM in a flow-through column experiment at pH >6.0. These investigations provide a systemic understanding of the Zn adsorption mechanisms on CFAPG and an SCM reference for the application and prediction of geopolymers in heavy metal-contaminated water remediations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils. Final Report

This University of Massachusetts, Amherst project, "Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils" started on 1st February 2009 and finished on August 31st 2011. The project consisted following tasks: Task 1.0: Char Removal by Membrane Separation Technology The presence of char particles in the bio-oil causes problems in storage and end-use. Currently there is no well-established technology to remove char particles less than 10 micron in size. This study focused on the application of a liquid-phase microfiltration process to remove char particles from bio-oil down to slightly sub-micron levels. Tubular ceramic membranes of nominal pore sizes 0.5 and 0.8m were employed to carry out the microfiltration, which was conducted in the cross-flow mode at temperatures ranging from 38 to 45 C and at three different trans-membrane pressures varying from 1 to 3 bars. The results demonstrated the removal of the major quantity of char particles with a significant reduction in overall ash content of the bio-oil. The results clearly showed that the cake formation mechanism of fouling is predominant in this process. Task 2.0 Acid Removal by Membrane Separation Technology The feasibility of removing small organic acids from the aqueous fraction of fast pyrolysis bio-oils using nanofiltration (NF) and reverse osmosis (RO) membranes was studied. Experiments were carried out with a single solute solutions of acetic acid and glucose, binary solute solutions containing both acetic acid and glucose, and a model aqueous fraction of bio-oil (AFBO). Retention factors above 90% for glucose and below 0% for acetic acid were observed at feed pressures near 40 bar for single and binary solutions, so that their separation in the model AFBO was expected to be feasible. However, all of the membranes were irreversibly damaged when experiments were conducted with the model AFBO due to the presence of guaiacol in the feed solution. Experiments with model AFBO excluding guaiacol were also conducted. NF membranes showed retention factors of glucose greater than 80% and of acetic acid less than 15% when operated at transmembrane pressures near 60 bar. Task 3.0 Acid Removal by Catalytic Processing It was found that the TAN reduction in bio-oil was very difficult using low temperature hydrogenation in flow and batch reactors. Acetic acid is very resilient to hydrogenation and we could only achieve about 16% conversion for acetic acid. Although it was observed that acetic acid was not responsible for instability of aqueous fraction of bio-oil during ageing studies (described in task 5). The bimetallic catalyst PtRe/ceria-zirconia was found to be best catalyst because its ability to convert the acid functionality with low conversion to gas phase carbon. Hydrogenation of the whole bio-oil was carried out at 125°C, 1450 psi over Ru/C catalyst in a flow reactor. Again, negligible acetic acid conversion was obtained in low temperature hydrogenation. Hydrogenation experiments with whole bio-oil were difficult to perform because of difficulty to pumping the high viscosity oil and reactor clogging. Task 4.0 Acid Removal using Ion Exchange Resins DOWEX M43 resin was used to carry out the neutralization of bio-oil using a packed bed column. The pH of the bio-oil increased from 2.43 to 3.7. The GC analysis of the samples showed that acetic acid was removed from the bio-oil during the neutralization and recovered in the methanol washing. But it was concluded that process would not be economical at large scale as it is extremely difficult to regenerate the resin once the bio-oil is passed over it. Task 5.0 Characterization of Upgraded Bio-oils We investigated the viscosity, microstructure, and chemical composition of bio-oils prepared by a fast pyrolysis approach, upon aging these fuels at 90ºC for periods of several days. Our results suggest that the viscosity increase is not correlated with the acids or char present in the bio-oils. The viscosity increase is due to formation of high molecular weight polymeric species over time. Our work also suggests that hydrogenation of the samples is beneficial in eliminating the viscosity increase. Task 6.0 Commercialization Assessment Renewable Oil International LLC (ROI) was responsible for Task 6.0, Commercialization Assessment. As part of this effort ROI focused on methods to reduce char carryover in the vapor stream from the fast pyrolysis reactor and residence time of the vapor in the reactor. Changes were made in the bio-oil recovery methodology and a reactor sweep gas used to reduce vapor residence time. Cyclones were placed in the vapor stream to reduce char particulate carryover. Microfiltration of the bio-oil was also researched to remove char particulate from the bio-oil. The capital cost for these improvements would be less than 2% of the total plant capital cost.

09 BIOMASS FUELS↗

Beyond the classical kinetic model for chronic graphite oxidation by moisture in high temperature gas-cooled reactors

Four grades of nuclear graphite with various microstructures were subjected to accelerated oxidation tests in helium with traces of moisture and hydrogen in order to evaluate the effects of chronic oxidation on graphite components in high temperature gas cooled reactors. Kinetic analysis showed that the Langmuir-Hinshelwood (LH) model cannot consistently reproduce all results. In particular, at high temperatures and water partial pressures oxidation was always faster than the LH model predicts, with stronger deviations for superfine grain graphite than for medium grain grades. It was also found empirically that the apparent reaction order for water has a sigmoid-type variation with temperature which follows the integral Boltzmann distribution function. This suggests that the apparent activation with temperature of graphite reactive sites that causes deviations from the LH model is rooted in specific structural and electronic properties of surface sites on graphite. A semi-global kinetic model was proposed, whereby the classical LH model was modified with a temperature-dependent reaction order for water. The new Boltzmann-enhanced model (BLH) was shown to consistently predict experimental oxidation rates over large ranges of temperature (800-1100 oC) and partial pressures of water (3-1200 Pa) and hydrogen (0-300 Pa), not only for the four grades of graphite but also for the historic grade H-451. The BLH model offers as more reliable input for modeling the chemical environment effects during the life-time operation of new grades of graphite in advanced nuclear reactors operating at high and very high temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Shock state distributions in porous tantalum and characterization with multipoint velocimetry

Heterogenous materials under shock compression can be expected to reach different shock states throughout the material according to local differences in microstructure and the history of wave propagation. Here, in this work, a compact, multiple-beam focusing optic assembly is used with high-speed velocimetry to interrogate the shock response of porous tantalum films prepared through thermal-spray deposition. The distribution of particle velocities across a shocked interface is compared to results obtained using a set of defocused interferometric beams that sampled the shock response over larger areas. The two methods produced velocity distributions along the shock plateau with the same mean, while a larger variance was measured with narrower beams. The finding was replicated using three-dimensional, mesoscopically resolved hydrodynamics simulations of solid tantalum with a pore structure mimicking statistical attributes of the material and accounting for radial divergence of the beams, with agreement across several impact velocities. Accounting for pore morphology in the simulations was found to be necessary for replicating the rise time of the shock plateau. The validated simulations were then used to show that while the average velocity along the shock plateau could be determined accurately with only a few interferometric beams, accurately determining the width of the velocity distribution, which here was approximately Gaussian, required a beam dimension much smaller than the spatial correlation lengthscale of the velocity field, here by a factor of ∼30×, with implications for the study of other porous materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of the pore size in multi-walled carbon nanotubes on the hydrogen storage behaviors

Activated multi-walled carbon nanotubes (A-MWCNTs) were prepared using a chemical activation method to obtain well-developed pore structures for use as hydrogen storage materials. The microstructure and crystallinity of the A-MWCNTs were evaluated by X-ray diffraction and Fourier transform Raman spectroscopy. The textural properties of the A-MWCNTs were investigated by nitrogen gas sorption analysis at 77 K. The hydrogen storage capacity of the A-MWCNTs was evaluated at 77 K and 1 bar. The results showed that the specific surface area of the MWCNTs increased from 327 to 495 m{sup 2}/g as the activation temperature was increased. The highest hydrogen storage capacity was observed in the A-MWCNTs sample activated at 900 Degree-Sign C (0.54 wt%). This was attributed to it having the narrowest microporosity, which is a factor closely related to the hydrogen storage capacity. This shows that the hydrogen storage behaviors depend on the pore volume. Although a high pore volume is desirable for hydrogen storage, it is also severely affected if the pore size in the A-MWCNTs for the hydrogen molecules is suitable for creating the activation process. Highlights: Black-Right-Pointing-Pointer The AT-800 and AT-900 samples were prepared by a chemical activation method at activation temperature of 800 and 900 Degree-Sign C, respectively. Black-Right-Pointing-Pointer The AT-900 sample has the narrowest peak in comparison with the AT-800 sample, resulting from the overlap of the two peaks (Peak I and Peak II). Black-Right-Pointing-Pointer This overlapping effect is due to the newly created micropores or shrinkages of pores in Peak II. So, these determining characteristics are essential for designing materials that are suitable for molecular hydrogen storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High stereographic resolution texture and residual stress evaluation using time-of-flight neutron diffraction

Neutron diffraction texture measurements provide bulk averaged textures with excellent grain orientation statistics, even for large-grained materials, owing to the probed volume being of the order of 1 cm 3 . Furthermore, crystallographic parameters and other valuable microstructure information such as phase fraction, coherent crystallite size, root-mean-square microstrain, macroscopic or intergranular strain and stress, etc. can be derived from neutron diffractograms. A procedure for combined high stereographic resolution texture and residual stress evaluation was established on the pulsed-neutron-source-based engineering materials diffractometer TAKUMI at the Materials and Life Science Experimental Facility of the Japan Proton Accelerator Research Center, through division of the neutron detector panel regions. Pole figure evaluation of a limestone standard sample with a well known texture suggested that the precision obtained for texture measurement is comparable to that of the established neutron beamlines utilized for texture measurement, such as the HIPPO diffractometer at the Los Alamos Neutron Science Center (New Mexico, USA) and the D20 angle-dispersive neutron diffractometer at the Institut Laue–Langevin (Grenoble, France). A high-strength martensite–austenite multilayered steel was employed for further verification of the reliability of simultaneous Rietveld analysis of multiphase textures and macro stress tensors. By using a texture-weighted geometric mean micromechanical (BulkPathGEO) model, a macro stress tensor analysis with a plane stress assumption showed a rolling direction–transverse direction (RD–TD) in-plane compressive stress (about –330 MPa) in the martensite layers and an RD–TD in-plane tensile stress (about 320 MPa) in the austenite layers. The phase stress partitioning was ascribed mainly to the additive effect of the volume expansion during martensite transformation and the linear contraction misfit between austenite layers and newly transformed martensite layers during the water quenching process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

HTO and selenate diffusion through compacted Na-, Na–Ca-, and Ca-montmorillonite

Radionuclide transport in smectite clay barrier systems used for nuclear waste disposal is controlled by diffusion, with adsorption significantly retarding transport rates. While a relatively minor component of spent nuclear fuel, 79 Se is a major driver of the safety case for spent fuel disposal due to its long half-life (3.3×10 5 yr) and its low adsorption to clay (K D < 10 L/kg), thus a thorough understanding of Se diffusion through clay is critical for understanding the long-term safety of spent fuel disposal systems. Through-diffusion experiments with tritiated water (HTO, conservative tracer) and Se(VI) were conducted with a well-characterized, purified montmorillonite source clay (SWy-2) under a constant ionic strength (0.1 M) and three different electrolyte compositions: Na + , Ca 2+ , and a Na + -Ca 2+ mixture at pH 6.5 in order to probe the effects of electrolyte composition and interlayer cation composition on clay microstructure, Se(VI) aqueous speciation, and ultimately diffusion. Further, the results were modeled using a reactive transport modeling approach to determine values of porosity (ε), D e (effective diffusion coefficient), and K D (distribution coefficient for adsorption). HTO diffusive flux was higher in Ca-montmorillonite (D e =1.68×10 -10 m 2 s -1 ) compared to Na-montmorillonite (De=7.83×10 -11 m 2 s -1 ). This increase in flux is likely due to a greater degree of clay layer stacking in the presence of Ca 2+ compared to Na + , which leads to larger inter-particle pores. Overall, the Se(VI) flux was much lower than the HTO flux due to anion exclusion, with Se(VI) flux following the order Ca (D e = 1.03×10 -11 m 2 s -1 ) > Na–Ca (D e = 2.12×10 -12 m 2 s -1 ) > Na (D e = 1.28×10 -12 m 2 s -1 ). These differences in Se(VI) flux are due to a combination of factors, including (1) larger accessible porosity in Ca-montmorillonite due to clay layer stacking and smaller electrostatic effects compared to Na-montmorillonite, (2) larger accessible porosity for neutral-charge CaSeO4 species which makes up 32% of aqueous Se(VI) in the pure Ca system, and (3) possibly higher Se(VI) adsorption for Ca-montmorillonite. Through a combination of experimental and modeling work, this study highlights the compounding effects that electrolyte and counterion compositions can have on radionuclide transport through clay. Diffusion models that neglect these effects are not transferable from laboratory experimental conditions to in situ repository conditions.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The structure, composition, and performance impact of a YSZ-GDC interdiffusion layer in solid oxide electrolysis cells

This study provides a combined experimental and computational investigation into the structure and impact of the cation interdiffusion layer that appears at the gadolinium doped ceria (GDC)/yttria stabilized zirconia (YSZ) interface in solid oxide electrolysis cells (SOECs). Scanning transmission electron microscopy (STEM) illustrates that a ∼0.4 μm interdiffusion layer (IDL) with an intermixed cation distribution and fine grain size forms upon sintering. STEM identifies that the interdiffusion layer exists in the cubic fluorite structure despite changes in cation composition. The interdiffusion layer microstructure formed during sintering does not change during SOEC testing at either 1.3V or heightened voltage pulse testing. Modeling predicts that ionic conductivity may decrease in the interdiffusion layer due to Coulombic trapping between mobile oxygen vacancies and excess Gd 3+ acceptor dopants. Yet, the density and continuous nature of the layer should benefit cell stability by substantially reducing the formation of SrZrO 3 , which is corroborated by STEM and Synchrotron X-ray diffraction (XRD). We conclude that the interdiffusion layer acts as a beneficial barrier to Sr diffusion, when operating in a regime where electrolyte void formation is not observed.

organic↗

Inhomogeneous Magnetic Anisotropy in an Fe 5– x GeTe 2 Nanoflake Observed by Imaging

Few-layer flakes of ferromagnetic Fe 5–x GeTe 2 with x = 0.3 (F5GT) possess a c-axis magnetocrystalline anisotropy that is large enough below ∼200 K to outcompete the easy-plane shape anisotropy, yielding distinctive magnetic microstructures with out-of-plane (OOP) magnetizations. Using photoemission electron microscopy (PEEM) with magnetic contrast from X-ray magnetic circular dichroism (XMCD) to study a thermally demagnetized h-BN-protected nanoflake of F5GT at 110 K, we observe a micron-scale coexistence between domains with OOP magnetizations (∼70% areal fraction) and hitherto unknown domains in which in-plane (IP) magnetization components dominate (∼30% areal fraction). The regions with dominant IP magnetization components do not correlate with small variations of flake thickness (6–10 nm) and instead arise from local changes of magnetocrystalline anisotropy due to a hitherto unidentified chemical inhomogeneity that we suggest to be a higher concentration of Fe vacancies. Our observation of micron-scale inhomogeneity would likely be missed if imaging a single flake orientation and should affect the viability and performance of van der Waals (vdW) spintronic devices with F5GT electrodes.

2D materials↗