Search NASA⌕ Search

SEARCH · Search NASA

Results for “process control and optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Optimization and understanding of ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst for enhanced CO 2 -methanol conversion at low temperature and pressure

Cu-ZnO-Al 2 O 3 is the most widely applied catalyst for CO 2 hydrogenation to methanol. However, it is still a challenge to produce methanol using this catalyst under low-temperature (<250 °C) and low-pressure (<10 bar) conditions with desirable yield and selectivity. In this work, by tuning the experimental processing parameters such as solvent, loading amount, and annealing temperature, highly improved ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalysts have been successfully demonstrated. Here, by using organic solvent (N,N-dimethylformamide (DMF), acetone, or isopropanol) for dip-coating loading process instead of deionized (DI) water, Cu-ZnO-Al 2 O 3 nanocatalysts was comparatively better dispersed on the nanorod array support with populated and abundant active sites, thus enhancing the methanol yield. With the control of the loading amount and annealing temperature, finely distributed Cu nanoparticles were obtained on the ZnO nanorod surfaces to enhance the interactions between Cu and ZnO nanorod surfaces. Further improvement of the catalyst performance is demonstrated by tuning the reaction space velocity. At 200 °C and 10 bar conditions, the optimized catalyst achieved a methanol yield of 6.46 mol h –1 kg –1 with 100 % selectivity. The good stability after prolonged testing of the catalysts demonstrates the potential practical implementation. The in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) measurements under the 1 bar reveal that the CO 2 hydrogenation to methanol on the ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst follows the CO reaction pathway, due to the surface oxygen vacancies on ZnO nanorods which facilitate CO 2 dissociation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Route-Based Online Energy Management of a PHEV and Sensitivity to Trip Prediction

In this paper, we present a method of optimizing the energy management of a plug-in hybrid electric vehicle (PHEV) using GIS-assisted stochastic trip prediction. A process was developed to synthesize speed profiles through a combination of Markov chains and information from a geographical information system (GIS) about the future route. In a potential real-world scenario, the future trip (speed, grade, stops, etc.) can be estimated, but not deterministically known. The stochastic trip prediction process models such uncertainty. The route-based energy management presented in this paper uses the Pontryagin Minimum Principle (PMP). A PMP strategy was implemented in a Simulink controller for a model of Prius-like PHEV and compared to a baseline strategy using Autonomie, an automotive modeling environment. An itinerary was defined, and several speed profiles were synthesized. It was then possible to evaluate the sensitivity of PMP tuning to the speed profile, providing insights about the applicability of PMP control in real-world situations.

energy mangement↗

Accelerating Multivariate Functional Approximation Computation with Domain Decomposition Techniques⋆

Modeling large datasets through Multivariate Functional Approximations (MFA) provide an elegant way to handle many visualization and scientific analysis workflows. The process necessitates scalable data partitioning methods to compute MFA representations efficiently without compromising the accuracy or continuity of the reconstructed solution. We propose a domain -decomposed method for computing the MFA with B -spline bases, which reduces the total work per task and uses a restricted Additive Schwarz (RAS) method to converge the control point data degrees -of -freedom along subdomain boundaries. We provide an in-depth analysis of the parallel approach with domain decomposition solvers, aiming to minimize local subdomain error residuals and recover high -order continuity at subdomain interfaces with appropriate choices of knot overlaps. The communication cost, determined by the overlap regions in the RAS implementation, is optimized to recover the numerical error profile of the single subdomain case. Our proposed method stands in contrast to previous methods, which typically only recover either C 0 or at best C 1 continuity for arbitrary B -spline degree expansions, or those that require post -processing to blend discontinuities in the reconstructed data. We demonstrate the effectiveness of our approach using analytical and real -world datasets in 1D, 2D, and 3D through both strong and weak scaling studies. The performance results indicate that the overall cost of computing the approximation is directly proportional to the underlying nearest -neighbor communication implementation, and is only weakly dependent on the overlap region size that determines the size of the messages. This finding underscores the efficiency and scalability of our proposed method, making it a promising solution for handling large datasets in scientific workflows.

additive Schwarz solvers↗

Novel Polyethylenimine–Acrylamide/SiO 2 Hybrid Hydrogel Sorbent for Rare-Earth-Element Recycling from Aqueous Sources

Recycling rare earth elements (REEs) becomes increasingly important due to their supply vulnerability and increasing demands in industry, agriculture, and national security. Hybrid hydrogel sorbents were outstanding due to their high stability and selectivity. Organic-inorganic hybrid hydrogels were synthesized by thermo-polymerization of acrylamide onto PEI polymer chain with N,N’-methylene bisacrylamide as a crosslinker. The grafted network was evidenced by DRIFTS and XPS. The porous structure was observed by SEM. Crosslink degree, PEI grafting degree, and SiO 2 concentration were studied to optimize the REEs adsorption. The pH value of the medium greatly affected REE adsorption capacity, where the nearly neutral conditions gave the strongest bonding of REEs to active sites. Moreover, kinetic studies showed that the rate-determining step of the adsorption process was chemical sorption, and that REE diffusion within micropores was the control step for, specifically, intraparticle diffusion. The adsorbents showed excellent selectivity and recyclability for REEs through 5 adsorption-desorption cycles in contact with synthetic acid mine drainage solution. A high separation toward REEs over fouling metals was achieved by using a citrate-based buffer eluent solution. This hybrid hydrogel shows promise for the recycling of REEs from aqueous solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Comprehensive Methodology to Evaluate Losses and Process Variations in Silicon Solar Cell Manufacturing

Novel, high-throughput metrology methods are used in this paper for detailed performance loss analysis of approximately 400 industrial crystalline silicon solar cells, all coming from the same production line. The characterization sequence combines traditional global cell measurements (e.g., current-voltage, Suns-VOC) with camera-based cell imaging of voltage distribution and power dissipation from photoluminescence and lock-in thermography, respectively. Spatial variations in current collection are visualized using a high-speed external quantum efficiency and reflectance measurement technique. A nondestructive transfer length method (TLM) measurement technique is also implemented, featuring circular TLM structures hidden within the busbars of the cells. The variance of individual loss parameters and their impact on cell performance are quantified for this large group of cells. Based on correlations performed across parameters, recombination losses in the bulk and rear surface of the cell are shown to be the primary limiting factor for the cell efficiency. The nature of these distributions and correlations provide important insights about loss mechanisms in industrial solar cells, helping to prioritize efforts for optimizing the performance of the production line. Additionally, many of the parameters extracted from these techniques can be tied back to incoming material quality issues (e.g., poor bulk carrier lifetime, nonuniform wafer doping) and to individual unit processes (e.g., texturing, phosphorus diffusion, silicon nitride deposition, metallization), allowing the data to be used directly for process control in manufacturing. All of the datasets are made available for download.

14 SOLAR ENERGY↗

Status Report on the High-Temperature Steam Electrolysis Plant Model Developed in the Modelica Framework (FY17)

This report has been prepared as part of an effort to design and build a modeling and simulation (M&S) framework to assess the economic viability of a nuclear-renewable hybrid energy system (N-R HES). In order to facilitate dynamic M&S of such an integrated system, research groups in multiple national laboratories have been developing various subsystems as dynamic physics-based components using the Modelica programming language. In fiscal year 2015 (FY15), Idaho National Laboratory (INL) performed a dynamic analysis of two region-specific N-R HES configurations, including the gas-to-liquid (natural gas to Fischer-Tropsch synthetic fuel) and brackish water reverse osmosis desalination plants as industrial processes. In FY16, INL developed two additional subsystems in the Modelica framework: (1) a high-temperature steam electrolysis (HTSE) plant as a high priority industrial plant to be integrated with a light water reactor (LWR) within an N-R HES and (2) a gas turbine power plant as a secondary energy supply. In FY17, five new components (i.e., a feedwater pump, a multi-stage compression system, a sweep-gas turbine, flow control valves, and pressure control valves) have been incorporated into the HTSE system proposed in FY16, aiming to better realistically characterize all key components of concern. Special attention has been given to the controller settings based on process models (i.e., direct synthesis method), aiming to improve process dynamics and controllability. A dynamic performance analysis of the improved LWR/HTSE integration case was carried out to evaluate the technical feasibility (load-following capability) and safety of such a system operating under highly variable conditions requiring flexible output. The analysis (evaluated in terms of the step response) clearly shows that the FY17 model resulted in superior output responses with much smaller settling times and less oscillatory behavior in response to disturbances in the electric load than those observed with the FY16 model. Simulation results involving several case studies show that the suggested control scheme could maintain the controlled variables (including the steam utilization factor, cathode stream inlet composition, and temperatures and pressures of the process streams at various locations) within desired limits under various plant operating conditions. The results also indicate that the proposed HTSE plant could provide operational flexibility to participate in energy management at the utility scale by dynamically optimizing the use of excess plant capacity within an N-R HES.

08 HYDROGEN↗

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration - FY2018 Final Report

High-value R2R processing is used to support a wide range of products in applications which span many industrial business sectors. The overall R2R process technology can be considered as “mature” as the process methodology and has been in use for decades. This continuous processing technique traditionally involves deposition of material(s) onto moving webs or carriers or other continuous R2R, belt-fed, or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Current process technologies, which typify “roll to roll”, include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multi-layer technologies can be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, a means must be available to enable manufacture of these products in a cost-competitive manner that is affordable by the general consumer. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches.Within the DOE EERE AMO, it was recognized that establishment of a program supported at the DOE National Laboratories, along with their immense design of materials and equipment modelling capabilities enabled with use of high-performance computing, could take advantage of available R2R infrastructure to manufacture new technologies. In FY 2016, a R2R Consortium was established and provided with initial “seed” funding to take an approach that was envisioned to be supportable by advanced manufacturing R2R processes. This collaborative approach was designed to foster identification and development of materials and processes related to R2R for clean-energy product development. Using computational and experimental capabilities by acknowledged subject matter experts within the supported National Laboratory system, this collaborative project would leverage the capabilities and expertise at each of four laboratories to further the development of an enabling high-volume cost-competitive platform technology. The collaboration team that is comprised of ORNL, ANL, NREL and LBNL, coordinating with EPB and other selected industry partners, was formed in April 2016 to initially address enhancing battery electrode performance and R2R manufacturing challenges. The research efforts were to predict and measure changes and results in electrode morphology and performance based on process condition changes; to evaluate mixed, active, particle size deposition and drying for novel electrode materials; to model various process condition changes and the resulting morphology and electrode performance; and to develop and validate NDE techniques for in-line measurement of battery electrode material properties. These efforts carried through FY 2017 and completed at the end of FY 2018.The approach was to look at compositions of materials with different particle sizes to make electrode samples using a R2R manufacturing process. The shape, size, and morphology of the materials, the chemistry of the formulation, the nature of slurries, their coating rate, the rate of drying all play a role in determining the final coating architecture, quality, and performance. A commercial cathode material was selected to make a series of cathodes and anodes by single pass, dual pass and slot die methods. Analysis of all the compiled results for this battery electrode development were that the best performing cathodes included: dual-pass electrode with large particles near the foil, mixed small and large particles, and small particles only. Whereas, the best performing anodes were with a mix of small and large graphite particles. An additional core project was added in FY 2017 to conduct studies of fuel cell materials that can be produced using R2R processes. The goal of this project is to explore, understand and optimize material and process parameters to support increased throughput, increased quality, and reduced cost for high volume production of gas-diffusion electrodes (GDEs) for PEMFCs. Project work in FY 2018 were to use a R2R process to fabricate electrodes without ionomer overlayer that can produce the equivalent mass activity as spray-coated electrodes with an ionomer overlayer. Oxygen-limiting current measurements were utilized to optimize oxygen mass transport. Alcohol-rich solvents were investigated, and results were that the alcohol and water ratio can be tuned to control ionomer distribution. Water-rich solvents produce a more dispersed ink which results in better high-current density performance.

36 MATERIALS SCIENCE↗

High Efficiency PEM Water Electrolysis Enabled by Advanced Catalysts, Membranes and Processes

In this project, advanced membranes and catalysts were integrated into membrane electrode assembles (porous transport electrodes (PTE) or catalyst coated membranes (CCM)) leveraging precision coating methods to enable control of electrode structures and demonstration of the best component performance possible with these materials. Partner collaborations allowed for advanced characterization of the formed interfaces and degradation mechanisms. New methods of forming hydrogen recombination layers were also developed, to move away from wet chemistry processes that would have limited realization and implementation of the optimized electrode configurations in a commercial environment.

08 HYDROGEN↗

Coordination of Endoplasmic Reticulum (ER) Signaling During Maize Seed Development

Seed storage reserves represent one of the most important sources of renewable fixed carbon and nitrogen found in nature. Seeds are well-adapted for diverting metabolic resources to synthesize storage proteins as well as enzymes and structural proteins needed for their transport and packaging into membrane bound storage protein bodies. Our underlying hypothesis is that the endoplasmic reticulum (ER) stress response provides the critical cellular control of metabolic flux required for optimal accumulation of storage reserves in seeds. This highly conserved response is a cellular mechanism to monitor the protein folding environment of the ER and restore homeostasis in the presence of unfolded or misfolded proteins. In seeds, deposition of storage proteins in protein bodies is a highly specialized process that takes place even in the presence of mutant proteins that no longer fold and package properly. The capacity of the ER to deposit these aberrant proteins in protein bodies during a period that extends several weeks provides an excellent model for deconvoluting the ER stress response of plants. We have focused in this project on the means by which the ER senses and responds to functional perturbations and the underlying intracellular communication that occurs among biosynthetic, trafficking and degradative pathways for proteins during seed development.

09 BIOMASS FUELS↗

Advances in 3D Gel Printing for Enzyme Immobilization

Incorporating enzymes with three-dimensional (3D) printing is an exciting new field of convergence research that holds infinite potential for creating highly customizable components with diverse and efficient biocatalytic properties. Enzymes, nature’s nanoscale protein-based catalysts, perform crucial functions in biological systems and play increasingly important roles in modern chemical processing methods, cascade reactions, and sensor technologies. Immobilizing enzymes on solid carriers facilitates their recovery and reuse, improves stability and longevity, broadens applicability, and reduces overall processing and chemical conversion costs. Three-dimensional printing offers extraordinary flexibility for creating high-resolution complex structures that enable completely new reactor designs with versatile sub-micron functional features in macroscale objects. Immobilizing enzymes on or in 3D printed structures makes it possible to precisely control their spatial location for the optimal catalytic reaction. Combining the rapid advances in these two technologies is leading to completely new levels of control and precision in fabricating immobilized enzyme catalysts. The goal of this review is to promote further research by providing a critical discussion of 3D printed enzyme immobilization methods encompassing both post-printing immobilization and immobilization by physical entrapment during 3D printing. Especially, 3D printed gel matrix techniques offer mild single-step entrapment mechanisms that produce ideal environments for enzymes with high retention of catalytic function and unparalleled fabrication control. Examples from the literature, comparisons of the benefits and challenges of different combinations of the two technologies, novel approaches employed to enhance printed hydrogel physical properties, and an outlook on future directions are included to provide inspiration and insights for pursuing work in this promising field.

3D printing↗

Strain Measurement of Geological Samples Subjected to Triaxial Stresses Experienced During Hydraulic Loading

Understanding stress and strain relationships and having the ability to predict these quantities for known load conditions is crucial to all geomechanical and, in some instances, reservoir flow applications. The constitutive equations governing the deformation of geological materials are typically adequate for bulk or large scale deformation and stress analyses. However, these rules are generally less precise in their ability to make accurate predictions in physical processes where highly localized material heterogeneity exists or where the presence of geometric irregularities such as micro-cracks may be present. This is especially relevant to EGS where hydraulic fracture propagation models are needed to develop optimal reservoir creation strategies and where fracture permeability is significantly influenced by regional stress states and may affect reservoir operation strategies. The deficiencies of the models used to describe these physical processes are a practical reality necessitated by the manner in which rock properties must be obtained. Conventional rock mechanics tests subject samples to controlled load conditions and measure bulk deformations of the sample or more localized deformations only on exposed surfaces of the sample. They are currently unable to comprehensively map the deformation state within the sample. For processes such as fracture, however, the state of a particular region within the rock drives the overall failure behavior of the sample. The authors believe that possessing a means to measure strains within samples subjected to hydraulic fracture loading conditions will provide a useful tool for understanding the localized effects not captured by conventional techniques and may serve as a method for improving hydraulic fracture models. An ongoing effort at Oak Ridge National Laboratory endeavors to develop a neutron diffraction based strain measurement capability to interrogate the strain state of a geological sample, at arbitrary internal locations, subjected to a triaxial stress state. The basis of the method and initial results for simple load conditions were reported at last year s Stanford Geothermal Workshop. This work will report results from recent neutron diffraction strain measurement experiments in which marble samples were subjected to load conditions more representative of hydraulic fracturing operations within a pressure cell specially designed for the reported strain measurement technique.

An, Ke↗

Control of Networked Traffic Flow Distribution - A Stochastic Distribution System Perspective

Networked traffic flow is a common scenario for urban transportation, where the distribution of vehicle queues either at controlled intersections or highway segments reflect the smoothness of the traffic flow in the network. At signalized intersections, the traffic queues are controlled by traffic signal control settings and effective traffic lights control would realize both smooth traffic flow and minimize fuel consumption. Funded by the Energy Efficient Mobility Systems (EEMS) program of the Vehicle Technologies Office of the US Department of Energy, we performed a preliminary investigation on the modelling and control framework in context of urban network of signalized intersections. In specific, we developed a recursive input-output traffic queueing models. The queue formation can be modeled as a stochastic process where the number of vehicles entering each intersection is a random number. Further, we proposed a preliminary B-Spline stochastic model for a one-way single-lane corridor traffic system based on theory of stochastic distribution control.. It has been shown that the developed stochastic model would provide the optimal probability density function (PDF) of the traffic queueing length as a dynamic function of the traffic signal setting parameters. Based upon such a stochastic distribution model, we have proposed a preliminary closed loop framework on stochastic distribution control for the traffic queueing system to make the traffic queueing length PDF follow a target PDF that potentially realizes the smooth traffic flow distribution in a concerned corridor.

Wang, Hong↗

Control of seeding phase for a cascaded laser wakefield accelerator with gradient injection

We demonstrated experimentally the seeding-phase control for a two-stage laser wakefield accelerator with gradient injection. By optimizing the seeding phase of electrons into the second stage, electron beams beyond 0.5 GeV with a 3% rms energy spread were produced over a short acceleration distance of ∼2 mm. Peak energy of the electron beam was further extended beyond 1 GeV by lengthening the second acceleration stage to 5 mm. Time-resolved magnetic field measurements via magneto-optical Faraday polarimetry allowed us to monitor the processes of electron seeding and acceleration in the second stage.

36 MATERIALS SCIENCE↗

Singular Perturbation for the Discounted Continuous Control of Piecewise Deterministic Markov Processes

This paper deals with the expected discounted continuous control of piecewise deterministic Markov processes (PDMP's) using a singular perturbation approach for dealing with rapidly oscillating parameters. The state space of the PDMP is written as the product of a finite set and a subset of the Euclidean space Double-Struck-Capital-R {sup n}. The discrete part of the state, called the regime, characterizes the mode of operation of the physical system under consideration, and is supposed to have a fast (associated to a small parameter {epsilon}>0) and a slow behavior. By using a similar approach as developed in Yin and Zhang (Continuous-Time Markov Chains and Applications: A Singular Perturbation Approach, Applications of Mathematics, vol. 37, Springer, New York, 1998, Chaps. 1 and 3) the idea in this paper is to reduce the number of regimes by considering an averaged model in which the regimes within the same class are aggregated through the quasi-stationary distribution so that the different states in this class are replaced by a single one. The main goal is to show that the value function of the control problem for the system driven by the perturbed Markov chain converges to the value function of this limit control problem as {epsilon} goes to zero. This convergence is obtained by, roughly speaking, showing that the infimum and supremum limits of the value functions satisfy two optimality inequalities as {epsilon} goes to zero. This enables us to show the result by invoking a uniqueness argument, without needing any kind of Lipschitz continuity condition.

97 MATHEMATICS AND COMPUTING↗

Identifying key factors of the seawater intrusion model of Dagu river basin, Jiaozhou Bay

Highlights: • The key factors of seawater intrusion model is identified by mutual entropy analysis. • Precipitation rate and groundwater pumping are the key factors for seawater intrusion. • The hydraulic conductivity of zone 1 has significant influence on seawater intrusion. Seawater intrusion is a complex groundwater - seawater interaction process, and it is influenced by many factors from ground surface to underground, from groundwater to seawater. Generally, for seawater intrusion model, some model parameters and boundary conditions are always specified by model users’ personal experiences or literature's reference value. The defective model would damage the groundwater management for controlling and preventing seawater intrusion when making decisions are based on this model. In order to improve the reliability of seawater intrusion model, the influences of model inputs on output should be identified prior at optimizing model inputs. Dagu river basin, Jiaozhou Bay is one of the most serious areas of seawater intrusion in China, and it is chosen as the study area in this study. The seawater intrusion model of Dagu river basin is built based on a general program SEAWAT4. The key influence factors of model output are analyzed by two sensitivity analysis methods, i.e., stepwise regression and mutual entropy. The results demonstrated that the most important influence factors which have largest sensitivities to groundwater Cl{sup -} concentration are the precipitation rate and groundwater pumping in agriculture area. In addition, the hydraulic conductivity of zone 1 has a non-negligible influence on seawater intrusion process. Stepwise regression analysis is capable of identifying most important influence factor, and it can’t handle complicated nonlinear input-output relationship. Mutual entropy analysis is reliable for identifying the influence factors for complex seawater intrusion model.

54 ENVIRONMENTAL SCIENCES↗

Evaluation of Alternative Atomistic Models for the Incipient Growth of ZnO by Atomic Layer Deposition

ZnO thin films are interesting for applications in several technological fields, including optoelectronics and renewable energies. Nanodevice applications require controlled synthesis of ZnO structures at nanometer scale, which can be achieved via atomic layer deposition (ALD). However, the mechanisms governing the initial stages of ALD had not been addressed until very recently. Investigations into the initial nucleation and growth as well as the atomic structure of the heterointerface are crucial to optimize the ALD process and understand the structure-property relationships for ZnO. We have used a complementary suite of in situ synchrotron x-ray techniques to investigate both the structural and chemical evolution during ZnO growth by ALD on two different substrates, i.e., SiO2 and Al2O3, which led us to formulate an atomistic model of the incipient growth of ZnO. The model relies on the formation of nanoscale islands of different size and aspect ratio and consequent disorder induced in the Zn neighbors' distribution. However, endorsement of our model requires testing and discussion of possible alternative models which could account for the experimental results. In this work, we review, test, and rule out several alternative models; the results confirm our view of the atomistic mechanisms at play, which influence the overall microstructure and resulting properties of the final thin film.

ALD↗