Search NASA⌕ Search

SEARCH · Search NASA

Results for “static structural analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Comparison of Structural Relaxation Behavior in As-Cast and Pre-Annealed Zr-Based Bulk Metallic Glasses Just below Glass Transition

In this paper, the α-relaxation of pre-annealed Zr 55 Cu 30 Ni 5 Al 10 bulk metallic glasses (BMGs) was compared with that of as-cast Zr-based BMGs including Zr 55 Cu 30 Ni 5 Al 10 . The α-relaxation was investigated by volume relaxation. The relaxation behavior was well described by a stretched exponential relaxation function, Φ (t) ≈ exp [ - (t/τ α ) β α ], with the isothermal relaxation time, τ α , and the Kohlrausch exponent, β α . The β α exhibited the strong temperature dependence for the pre-annealed BMG, while the weak temperature dependence was visualized for the as-cast BMG similar to the dynamic relaxation. The τ α ’s were modified by Moynihan and Narayanaswamy-Tool-Moynihan methods that reduce the difference in the thermal history of sample. Finally, as a result, the relaxation kinetics in the glass resembled that of a liquid deduced from the behavior of viscosity in the supercooled liquid.

36 MATERIALS SCIENCE↗

Transient superconductivity at nano- and meso-scales

High-T c superconductivity is surpassed by few, if any, other unsolved problems in contemporary physics in terms of its richness, complexity, impact on other fields, and potential technological importance in energy applications. Recent discoveries reveal that the highest transition temperatures emerge under extraordinary experimental conditions such as the strong perturbation of a single atomic layer material by the underlying substrate, application of ~200 GPa pressure or ~MV/cm static electric fields, or irradiation by intense femtosecond optical fields. Research in superconductivity under extreme experimental conditions is challenging and requires the development of novel experimental methods and new theoretical tools suitable to tackle the problem. Our team has approached the challenges of transient superconductivity under intense optical fields by rethinking the types of experimental observables that are best suited to elucidate the physics of light-induced effects. This exercise has identified the need for: i) ultra-fast spatio-temporal probes enabling access to plasmonic properties and also nano-scale inhomogeneities that are ubiquitous in unconventional superconductors; ii) meso-scale structures and hybrid meta-surfaces imperative for strong enhancement of optical fields and iii) theoretical approaches suitable to explain and predict the response of superconductors under ultra-fast photo-excitation. Co-PIs have already made major advances with developing capabilities i)-iii). Therefore, our team is poised to make significant progress in transient superconductivity by exploring novel spatio-temporal effects that currently remain unattainable. Co-investigators will search for light-induced superconductivity in the high-T c cuprates to build upon spectacular recent results still lacking independent confirmations. Novel data acquisition methods combined with nano-plasmonic imaging will allow our team to test the hypothesis of photo-induced superconducting pairing. Spatio-temporal experiments will provide insights into the interplay between superconductivity and competing orders in the cuprates. Co-PIs will also investigate strong light-matter interaction and superconductivity in FeSe monolayers. Finally, we will study spatio-temporal electrodynamics of planar Josephson junctions. This latter direction will allow our team to thoroughly characterize one of the most fundamental examples of inhomogeneity in all of unconventional superconductivity. The proposed experiments in combination with theoretical analysis will provide information that is difficult to obtain using alternative methods. Basov and Averitt will carry out pump-probe spectroscopy and nano-imaging experiments. Averitt and Hone will design and fabricate state-of-the-art meta-surfaces. Theoretical and computational studies of ultrafast transient phenomena will be carried out by Millis and Fogler. Modeling of time-resolved nano-optical effects will be done by Fogler. The bulk of the requested budget will be used to support graduate students at Columbia & UCSD that will be co-supervised by co-PIs. The proposed program is transformative, since it will enable an entire suite of experiments previously either impossible or technically implausible. It will deliver critically important insights not only into mechanisms of unconventional superconductivity but also to many other correlated quantum materials.

36 MATERIALS SCIENCE↗

CCSD(T) calculations of stabilities and properties of confined systems

We analyze energies, electron affinities and polarizabilities of small anions exposed to an external confinement. The second electron in free O{sup 2−} and S{sup 2−} anions is unbound. We investigate the stabilizing effect of the spherical harmonic-oscillator confining potential ω. on these anions employing the Hartree-Fock stability analysis as introduced by Čížek and Paldus. With increasing strength of the external harmonic-oscillator confinement potential ω the broken symmetry (BS) solutions are systematically eliminated. For ω larger than 0.1 all BS solutions for O{sup 2−} disappear. For ω larger than 0.13 the CCSD(T) energy of O{sup 2−} becomes more negative than the energy of the singly charged O{sup −} anion. We relate the harmonic-oscillator confining potential to a crystalline environment in which the O{sup 2−} and S{sup 2−} anions are stable. We also present a model allowing calculations of the in-crystal polarizabilities of anions. The model is based on CCSD(T) calculations of static polarizabilities of selected anions exposed to the spherical harmonic-oscillator confining potential ω This artificial confinement potential ω is then related to the ionic radii of the cation in representative crystal lattices. We investigate the polarizability of O{sup 2−} and S{sup 2−} anions in MgO, MgS, CaO, CaS, SrO, SrS, BaO and BaS crystals. We compare our results with alternative models for in-crystal polarizabilities. External confinement also stabilizes the uracil anion U{sup −}, as is shown by calculations with a stepwise micro-hydration of U{sup −}. Upon hydration is the CCSD(T) adiabatic electron affinity (AEA) of uracil enhanced by about 250 up to 570 meV in comparison with AEA of the isolated molecule, depending on the geometry of the hydrated uracil anion complex. We tried to find an analogy of the stabilization effect of the external confinement on the otherwise unstable anions. In uracil and its anion is the external confinement represented by the polarized continuum solvation model with dielectric constant as a variational parameter. The physical behavior of ions exposed to an artificial external, spherical harmonic-oscillator confining potential ω, the environment represented by a crystal structure and the confinement represented by the solvent, all have considerable stabilizing effect on the otherwise unstable free anion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Flexure fatigue testing of 90 deg graphite/epoxy composites

A great deal of research has been performed characterizing the in-plane fiber-dominated properties, under both static and fatigue loading, of advanced composite materials. To the author's knowledge, no study has been performed to date investigating fatigue characteristics in the transverse direction. This information is important in the design of bonded composite airframe structure where repeated, cyclic out-of-plane bending may occur. Recent tests characterizing skin/stringer debond failures in reinforced composite panels where the dominant loading in the skin is flexure along the edge of the frame indicate failure initiated either in the skin or else the flange, near the flange tip. When failure initiated in the skin, transverse matrix cracks formed in the surface skin ply closest to the flange and either initiated delaminations or created matrix cracks in the next lower ply, which in turn initiated delaminations. When failure initiated in the flanges, transverse cracks formed in the flange angle ply closest to the skin and initiated delamination. In no configuration did failure propagate through the adhesive bond layer. For the examined skin/flange configurations, the maximum transverse tension stress at failure correlates very well with the transverse tension strength of the composites. Transverse tension strength (static) data of graphite epoxy composites have been shown to vary with the volume of material stressed. As the volume of material stressed increased, the strength decreased. A volumetric scaling law based on Weibull statistics can be used to predict the transverse strength measurements. The volume dependence reflects the presence of inherent flaws in the microstructure of the lamina. A similar approach may be taken to determine a volume scale effect on the transverse tension fatigue behavior of graphite/epoxy composites. The objective of this work is to generate transverse tension strength and fatigue S-N characteristics for composite materials using 3-point flexure tests of 90 deg graphite/epoxy specimens. Investigations will include the volume scale effect as well as frequency and span-to-thickness ratio effects. Prior to the start of the experimental study, an analytical study using finite element modeling will be performed to investigate the span-to-thickness effect. The ratio of transverse flexure stress to shear stress will be monitored and its values predicted by the FEM analysis compared with the value obtained using a 'strength of materials' based approach.

Peck, Ann Nancy W.↗

Application of Combined Sustained and Cyclic Loading Test Results to Alloy 617 Elevated Temperature Design Criteria

Alloy 617 is a reference structural material for very high temperature components of advanced-gas cooled reactors with outlet temperatures in the range of 900-950°C . In order for designers to be able to use Alloy 617 for these high temperature components, Alloy 617 has to be approved for use in Section III (the nuclear section) of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code. A plan has been developed to submit a draft code for Alloy 617 to ASME Section III by 2015. However, the current rules in Subsection NH for the evaluation of strain limits and creep-fatigue damage using simplified methods based on elastic analysis have been deemed inappropriate for Alloy 617 at temperatures above 1200°F (650°C). The rationale for this exclusion is that at higher temperatures it is not feasible to decouple plasticity and creep deformation, which is the basis for the current simplified rules. This temperature, 1200 °F, is well below the temperature range of interest for this material in High Temperature Gas Cooled Reactor (HTGR) applications. The only current alternative is, thus, a full inelastic analysis which requires sophisticated material models which have been formulated but not yet verified. To address this issue, proposed code rules have been developed which are based on the use of elastic-perfectly plastic (EPP) analysis methods and which are expected to be applicable to very high temperatures.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Solid face sheets enable lattice metamaterials to withstand high-amplitude impulsive loading without yielding

Owing to their ability to provide tunable mechanical responses, lattice materials are frequently studied to elucidate their response to static and dynamic loads. However, these roles are typically in opposition: static loads must be supported sufficiently far away from the onset of buckling or yielding, whereas dynamic loads are typically ameliorated by crushing of the lattice, which provides excellent energy-absorption due to the large plastic deformation accompanying densification. In contrast, this work considers the octet truss as an exemplar topology, in a structural role where it must simultaneously support static loads while enduring high-amplitude impulsive loads. This study focuses on the ability to withstand impulsive loads without yielding, an essential prerequisite to enduring dual loading. Computational studies using the ALE3D hydrocode were performed to examine the response of the octet truss under a short temporal width impulse shape associated with laser-driven shocks. A key finding was that covering the lattice with a solid face sheet and treating this face sheet thickness as a design variable allows the Taylor-like pulse to be attenuated prior to entering the weaker lattice, at the cost of added mass up front. Experimental validation was accomplished by laser-driven shock testing, using octet trusses printed out of Ti-5Al-5V-5Mo-3Cr. The results show that for a given quantity of mass, the attenuation is maximized when as much mass as possible is moved into the face sheet, leaving a more slender lattice structure. The effect of placing mass in the face sheet rather than lattice beams dominates the effect of relative density, to the point where a low-mass structure with most of the mass concentrated in the face sheet can outperform a high-mass structure with most of the mass in the lattice. Finally, by further understanding the propagation of short pulse width waves within under-dense structures, this study expand the domain of applicability of such structures, including lattice materials, to challenging dual-loading regimes spanning decades of strain rates.

36 MATERIALS SCIENCE↗

Holographic Imaging of Evolving Laser-Plasma Structures

In the 1870s, English photographer Eadweard Muybridge captured motion pictures within one cycle of a horse’s gallop, which settled a hotly debated question of his time by showing that the horse became temporarily airborne. In the 1940s, Manhattan project photographer Berlin Brixner captured a nuclear blast at a million frames per second, and resolved a dispute about the explosion’s shape and speed. In this project, we developed methods to capture detailed motion pictures of evolving, light-velocity objects created by a laser pulse propagating through matter. These objects include electron density waves used to accelerate charged particles, laser-induced refractive index changes used for micromachining, and ionization tracks used for atmospheric chemical analysis, guide star creation and ranging. Our “movies”, like Muybridge’s and Brixner’s, are obtained in one shot, since the laser-created objects of interest are insufficiently repeatable for accurate stroboscopic imaging. Our high-speed photographs have begun to resolve controversies about how laser-created objects form and evolve, questions that previously could be addressed only by intensive computer simulations based on estimated initial conditions. Resolving such questions helps develop better tabletop particle accelerators, atmospheric ranging devices and many other applications of laser-matter interactions. Our photographic methods all begin by splitting one or more “probe” pulses from the laser pulse that creates the light-speed object. A probe illuminates the object and obtains information about its structure without altering it. We developed three single-shot visualization methods that differ in how the probes interact with the object of interest or are recorded. (1) Frequency-Domain Holography (FDH). In FDH, there are 2 probes, like “object” and “reference” beams in conventional holography. Our “object” probe surrounds the light-speed object, like a fleas swarming around a sprinting animal. The object modifies the probe, imprinting information about its structure. Meanwhile, our “reference” probe co-propagates ahead of the object, free of its influence. After the interaction, object and reference combine to record a hologram. For technical reasons, our recording device is a spectrometer (a frequency-measuring device), hence the name “frequency-domain” holography. We read the hologram electronically to obtain a “snapshot” of the object’s average structure as it transits the medium. Our published work shows numerous snapshots of electron density waves (“laser wakes”) in ionized gas (“plasma”), analogous to a water wake behind a boat. Such waves are the basis of tabletop particle accelerators, in which charged particles surf on the light-speed wave, gaining energy. Comparing our snapshots to computer simulations deepens understanding of laser wakes. FDH takes snapshots of objects that are quasi-static --- i.e. like Muybridge’s horse standing still on a treadmill. If the object changes shape, FDH images blur, as when a subject moves while a camera shutter is open. Many laser-generated objects of interest do evolve as they propagate. To overcome this limit of FDH, we developed .... (2) Frequency-Domain Tomography (FDT). In FDT, 5 to 10 probe pulses are fired simultaneously across the object’s path at different angles, like a crossfire of bullets. The object imprints a “streaked” record of its evolution on each probe, which we record as in FDH, then recover a multi-frame “movie” of the object’s evolving structure using algorithms of computerized tomography. When propagation distance exceeds a few millimeters, reconstructed FDT images distort. This is because the lenses that image probes to detector have limited depth of field, like cameras that cannot focus simultaneously on both nearby and distant objects. But some laser-generated objects of interest propagate over meters. For these applications we developed … (3) Multi-Object-Plane Phase-Contrast Imaging (MOP-PCI). In MOP-PCI, we image FDT-like probes to the detector from multiple “object planes” --- like recording an event simultaneously with several cameras, some focused on nearby, others on distant, objects. To increase sensitivity, we exploit a phase-contrast imaging technique developed by Dutch Nobel laureate Fritz Zernike in the 1930s. Using MOP-PCI we recorded single-shot movies of laser pulse tracks through more than 10 cm of air. We plan to record images of meter-long tracks of electron bunches propagating through plasma in an experiment at the Stanford Linear Accelerator Center (SLAC). This will help SLAC scientists understand, optimize and scale small plasma-based particle accelerators that have applications in medicine, industry, materials science and high-energy physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Conformation and dynamics of ring polymers under symmetric thin film confinement

Understanding the structure and dynamics of polymers under confinement has been of widespread interest, and one class of polymers that have received comparatively little attention under confinement is that of ring polymers. The properties of non-concatenated ring polymers can also be important in biological fields because ring polymers have been proven to be a good model to study DNA organization in the cell nucleus. From our previous study, linear polymers in a cylindrically confined polymer melt were found to segregate from each other as a result of the strong correlation hole effect that is enhanced by the confining surfaces. By comparison, our subsequent study of linear polymers in confined thin films at similar levels of confinements found only the onset of segregation. Here, we use molecular dynamics simulation to investigate the chain conformations and dynamics of ring polymers under planar (1D) confinement as a function of film thickness. Our results show that conformations of ring polymers are similar to the linear polymers under planar confinement, except that ring polymers are less compressed in the direction normal to the walls. While we find that the correlation hole effect is enhanced under confinement, it is not as pronounced as the linear polymers under 2D confinement. Finally, we show that chain dynamics far above Tg are primarily affected by the friction from walls based on the monomeric friction coefficient we get from the Rouse mode analysis.

36 MATERIALS SCIENCE↗

Analyses Supporting Design Review of TREAT Multi-SERTTA Experiment Test Vehicle

The Transient Test Reactor (TREAT) Facility was designed to evaluate nuclear fuels and structural materials under simulated nuclear excursion and transient power/cooling mismatch situations that could be encountered in nuclear reactors [1]. It was historically operated from 1959 through 1994; ongoing activities at Idaho National Laboratory (INL) include resumption of transient testing capabilities to generate experimental data suitable to validate advanced modeling and simulation of these transient conditions, supporting current and next generation power reactor design and nuclear safety [2]. The resumption of transient testing requires new experiment vehicle designs to satisfy testing needs. The most developed experiment test vehicle candidate in TREAT’s arsenal will be the Multi-SERTTA (Static Environment Rodlet Transient Test Apparatuses) [3], which accommodates up to four concurrent rodlets under separate environmental conditions. An overview of the Multi-SERTTA, which would be placed at the center of the TREAT core during use, is shown in Figure 1. In the current design, all four rodlet test vessels are identical except for flux shaping collar material content to meet design needs. As the date rapidly approaches for TREAT restart, there is a need to have the Multi-SERTTA design approved and tested. Test experiments are an integral component of TREAT operations, and will be integrated among initial restart testing and supporting core reactor physics measurements. An integral step in finalization of any test vehicle design for TREAT is the hosting and resolution of a formal design review.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Experimental thermal equation of state of B 2–KCl

The alkali halides are often used as optically-transparent pressure-transmitting media and thermal insulators in laser-heated diamond anvil cell experiments. High P-T equations of state for these materials would allow them to be used simultaneously as sensitive in situ pressure markers, making sample preparation and data analysis simpler. KCl is especially useful for this application because its high melting point, crystallographic simplicity, and low electron density are ideal for use in high-temperature X-ray diffraction experiments. However, the high-temperature static equation of state data for this material is limited in pressure to 8 GPa. As experiments routinely exceed 100 GPa in pressure and thousands of Kelvin, it is necessary for the equation of state of KCl to be determined experimentally at these conditions if it is to be used as an equation of state calibrant in the future. This work combines new high-pressure, high-temperature data of the B2 phase of KCl (up to 167 GPa and 2400 K) with the previously published room-temperature data of Dewaele et al. (2012) to produce a Mie-Gruneisen-Debye thermal equation of state for this material. The room temperature equation of state parameters are similar to those reported previously: V 0 = 32.0(3) cm 3 /mole, K 0 = 24(1) GPa and $K$$^{'}_{0}$ = 4.56(5). The thermal parameters, 0 and q, are 2.9(4) and 1.0(1), respectively. While a q of 1 is expected, the 0 is higher than expected from previous calculations, lower pressure experimental data, and the available shockwave data. Here, previously-reported equations of state underestimate the pressure of KCl at high temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

FEASIBILITY OF HELIOSPHERIC IMAGING FROM NEAR EARTH

Imaging solar wind structures via Thomson scattered sunlight has proved important to understanding the inner heliosphere. The principal challenge of heliospheric imaging is background subtraction: typical solar wind features are fainter than the zodiacal light and starfield by 2-3 orders of magnitude. Careful post-processing is required to separate the solar wind signal from the static background. Remnant background, and not photon noise, is the dominant noise source in current STEREO data. We demonstrate that 10× shorter exposure times would not strongly affect the noise level in these data. Further, we demonstrate that current processing techniques are sufficient to separate not only the existing background of the STEREO images but also diffuse variable backgrounds such as are expected to be seen from low Earth orbit. We report on a hare-and-hounds style study, demonstrating blind signal extraction from STEREO/HI-2 data that have been degraded by the addition of large-scale, time-dependent artifacts to simulate viewing through airglow or high-altitude aurora. We demonstrate removal of these effects via image processing, with little degradation compared to the original. Even with as few as three highly degraded source images over 48 hr, it is possible to detect and track large coronal mass ejections more than 40° from the Sun. This implies that neither the high altitude aurora discovered by Coriolis/SMEI, nor airglow effects seen from low Earth orbit, are impediments to a hypothetical next-generation heliospheric imager in low Earth orbit; and also that post-processing is as important to heliospheric image qualitiy as are optical contamination effects.

79 ASTRONOMY AND ASTROPHYSICS↗

Predicting Dynamic-to-Static Correction Factor from Petrophysical Data and Chemostratigraphy using Unsupervised Machine Learning

Estimating static mechanical properties of stratigraphic layers is critical for optimizing subsurface engineering applications. To estimate dynamic-to-static correction factor F ds (static-to-dynamic Young’s modulus ratio) across the Caney shale interval in Oklahoma, USA, we integrated triaxial test measurements and petrophysical data, including well logs and X-ray fluorescence (XRF) using unsupervised machine learning (ML). We used a novel workflow that includes principal component analysis (PCA) to reduce data set dimensionality of well logs and XRF data sets—both separately and combined—creating three scenarios, and later applied inverse distance weighting (IDW) to derive F ds profiles for these scenarios. Furthermore, we applied K-means clustering on each scenario to predict depositional facies, and built a stiffness zonation profile through chemostratigraphic analysis of the terrigenous elements to validate the predicted F ds . The predicted F ds profile from each scenario using the PCA-IDW method was compared with the constant F ds approach from our previous study by calculating the root mean square error (RMSE). The combined data sets scenario yielded the lowest RMSE value of 0.113, while the RMSE values for the well logs and XRF scenarios were 0.131 and 0.129, respectively. In addition, the predicted F ds from the XRF scenario well-matched the stiffness zonation from the chemostratigraphic analysis that was built using the optimized K-means clustering of nine clusters for that scenario. These methods and findings offer a valuable tool for refining lithological classification and improving the F ds profile, potentially enhancing drilling and stimulation strategies for subsurface energy engineering applications.

clastic rock↗

Experimental Study of the 3 He and Neutron Spin Structure at Low Q 2 and The Upgrade of the JLab Polarized 3 He Target

In the scattering process off a nuclear or nucleon target, the Gerasimov-Drell-Hearn (GDH) sum rule for real photons (Q 2 =0 where Q 2 &equiv; -q 2 with q the photon's 4-momentum) relates static properties of the target particle's ground state to dynamic properties of all its excited states. On the other side of the Q 2 spectrum, the Bjorken sum rule holds in the Bjorken limit Q 2 &rarr; &infin;. Bjorken sum rule relates the final structure functions of the proton and neutron to the nucleon axial coupling constant in weak decay. These two sum rules belong to domains where calculations are achievable but use different degrees of freedom: hadronic degrees of freedom at low Q 2 versus partonic degrees of freedom at intermediate Q 2 . Meanwhile, different methods have been used to connect the two sum rules at finite Q 2 values: Chiral Perturbation Theory is used to expand the GDH sum rule while Operator Product Expansion is used to expand the Bjorken sum rule. In recent decades, improvements in polarized beam and polarized target techniques have made it possible to test theoretical predictions in the intermediate Q 2 region. During the Jefferson Lab (JLab) Hall A E97110 experiment, a precise measurement of polarized cross sections was performed at 0.02 < Q 2 < 0.3 GeV 2 using a polarized 3 He target as an effective polarized neutron target. The measured data allowed us to test predictions of Chiral Perturbation Theory at very low Q 2 . Furthermore, an extrapolation to the real photon point Q 2 =0 tests the GDH sum rule on the neutron. In order to reach the small angles necessary for the low Q 2 range, a new septum magnet was installed in Hall A for this experiment. Unfortunately, the magnet was mis-wired during initial running. There were therefore two periods for this experiment: the first period had the defective magnet due to mis-wiring; while in the second period, the magnet had been fixed and was working properly. The cross sections and the asymmetries for the first period must be extracted using a difficult and unusual method employing focal plane variables in the spectrometer. In the work described in this thesis, the target-plane and focal-plane method will be established first and confirmed by elastic scattering cross section measurements from carbon foil and 3 He targets. Cross sections and asymmetries of inelastic scattering were then extracted using the same method, which constitute the main physics results of this thesis. Preliminary results on ITT , the integral of the polarized cross section, were also extracted and are presented in this thesis. In addition to the data analysis of E97110, this thesis includes instrumentation work performed on the polarized 3 He target at JLab. For the 12 GeV program of JLab, the polarized 3 He target is being upgraded to satisfy new experimental requirements. The new target is a convection-based cell with two transfer tubes rather than a single transfer tube as in the former 6 GeV design. The first stage of the target upgrade aims to produce a 40 cm long, 10 amg target that can withstand 30 &mu;A of electron beam current with an in-beam polarization of 55%, doubling the figure-of-merit from the 6 GeV time. Several studies were conducted at the Test Lab of JLab on the new convection cell. Work and improvement done on the Pulse Nuclear Magnetic Resonance (NMR) polarimetry and its test results will be presented. As this thesis is written, the target is being installed in Hall C of JLab in preparation for a 6-month long running from November 2019 to May 2020.

Ton, Nguyen↗

High compressive energy absorption and shape recovery behavior of additively manufactured textile-inspired cylindrical braided metamaterials

Mechanical metamaterials (MMs) are engineered structures with unique mechanical properties that arise from their unique spatial arrangement or lattice-like structure. The most commonly designed MMs such as honeycomb and re-entrant auxetics are prone to failure at the sharp corners and weak joints due to the increased stress concentration under deformation. To mitigate this challenge, braided MM structures involving intertwining threads of nylon—forming curved unit cells—have been studied. These textile-inspired cylindrical braided metamaterials (CBMMs) with contrasting unit cells, namely diamond and regular CBMMs, were fabricated by 3D printing. The layer-by-layer deposited structure built by fused filament fabrication delivered an assembly of overlapped threads that are fused at the contact point. To understand deformation behavior of these MMs, finite element models were developed for various load scenarios including quasi-static compression, cyclic and creep loads at room temperature. Stress distribution, deformation mechanisms, and failure modes were analyzed and validated by experiments to analyze the geometries and associated performance. The diamond CBMMs showed stress softening at 30 % compressive strain, withstanding a load of ∼440 N, whereas the regular CBMMs at 50 % strain experienced ∼250 N. The diamond CBMMs delivered higher creep resistance under sustained load and better energy absorption under cyclic loading than the regular CBMMs. The latter, however, exhibited 94 % shape recovery in contrast to 88 % recovery in former prototype during their first cyclic load. In conclusion, this study helps design mechanical lightweight devices that endure significant sustained load and exhibit enhanced energy absorption and shape recovery characteristics in cyclic loading.

Creep↗

DOE Hydrogen Sorption Center of Excellence: Synthesis and Processing of Single-Walled Carbon Nanohorns for Hydrogen Storage and Catalyst Supports

The objective of the project was to exploit the unique morphology, tunable porosity and excellent metal supportability of single-walled carbon nanohorns (SWNHs) to optimize hydrogen uptake and binding energy through an understanding of metal-carbon interactions and nanoscale confinement. SWNHs provided a unique material to understand these effects because they are carbon nanomaterials which are synthesized from the 'bottom-up' with well-defined, sub-nm pores and consist of single-layer graphene, rolled up into closed, conical, horn-shaped units which form ball-shaped aggregates of {approx}100-nm diameter. SWNHs were synthesized without metal catalysts by the high-temperature vaporization of solid carbon, so they can be used to explore metal-free hydrogen storage. However, SWNHs can also be decorated with metal nanoparticles or coatings in post-processing treatments to understand how metals augment hydrogen storage. The project first explored how the synthesis and processing of SWNHs could be modified to tailor pore sizes to optimal size ranges. Nanohorns were rapidly synthesized at 20g/hr rates by high-power laser vaporization enabling studies such as neutron scattering with gram quantities. Diagnostics of the synthesis process including high-speed videography, fast pyrometry of the graphite target, and differential mobility analysis monitoring of particle size distributions were applied in this project to provide in situ process control of SWNH morphology, and to understand the conditions for different pore sizes. We conclude that the high-temperature carbon-vaporization process to synthesize SWNHs is scalable, and can be performed by electric arc or other similar techniques as economically as carbon can be vaporized. However, the laser vaporization approach was utilized in this project to permit the precise tuning of the synthesis process through adjustment of the laser pulse width and repetition rate. A result of this processing control in the project was to eliminate the large (2-3 nm) internal pores of typical SWNHs which were found not to store hydrogen effectively. Post processing treatments of the as-synthesized SWNHs focused on pore size, surface area, and metal decoration in order to understand the effects of each on measured hydrogen uptake. Wet chemistry and gas-phase oxidation treatments were developed throughout the life of the project to adjust the interstitial and slit pore sizes of the as-produced SWNHs, and increase the surface area to a maximum value of 2200 m2/g. In addition, wet chemistry approaches were used to develop methods to decorate the nanohorns with small Pt and Pd nanoparticles for metal-assisted hydrogen storage. Finally, oxygen-free decoration of SWNHs with alkaline earth metals (Ca) was developed using pulsed laser deposition and vacuum evaporation in order to produce surface coatings with high static electric fields sufficient to polarize and bind dihydrogen. Decoration of SWNHs with Pt and Pd nanoparticles resulted in enhanced binding energy (NREL, 36 kJ/mol), as well as enhancement in the room temperature uptake of 0.6 wt.% (for undecorated, oxidized, pure-C SWNHs at 20 bar), to 1.6 wt% for Pt- and Pd-decorated SWNHs at 100 bar, comparable to MOF-177 materials. NIST neutron scattering on gram quantity Pt- and Pd-decorated SWNHs showed clear evidence for 'spillover' type losses of molecular hydrogen and determined the onset temperature for this effect to be between 150K < T < 298K.High (2142 m2/g) surface area SWNH materials with variable pore sizes and metal-decorated SWNHs were demonstrated with metals (Pt, Pd) resulting in increased excess storage (3.5 wt. % at 77K). Compression results in bulk SWNH samples with density 1.03 g/cm3, and 30 g/L volumetric capacity. In summary, SWNHs were found to be unique carbon nanomaterials which can be produced continuously at high rates from vaporization of pure carbon. Their inherent pore structure exhibits significant room temperature hydrogen storage in sub-nm pores, and their morphology serves as an excellent metal catalyst support for small (2-3 nm nanoparticles). Pt- and Pd-nanoparticle-decorated SWNHs exhibit clear evidence for metal-assisted hydrogen storage which is activated at T>150 K, permitting additional room-temperature storage up to 1.8 wt.% at 100 bar. One of the key results of the project were theoretical predictions for doped, decorated, and filled nanostructures with distributed charge to maintain high static electric fields sufficient to polarize and bind hydrogen. This concept indicates a promising new direction for hydrogen storage materials.

08 HYDROGEN↗

Optimization of Car Body under Constraints of Noise, Vibration, and Harshness (NVH), and Crash

To be competitive on the today's market, cars have to be as light as possible while meeting the Noise, Vibration, and Harshness (NVH) requirements and conforming to Government-man dated crash survival regulations. The latter are difficult to meet because they involve very compute-intensive, nonlinear analysis, e.g., the code RADIOSS capable of simulation of the dynamics, and the geometrical and material nonlinearities of a thin-walled car structure in crash, would require over 12 days of elapsed time for a single design of a 390K elastic degrees of freedom model, if executed on a single processor of the state-of-the-art SGI Origin2000 computer. Of course, in optimization that crash analysis would have to be invoked many times. Needless to say, that has rendered such optimization intractable until now. The car finite element model is shown. The advent of computers that comprise large numbers of concurrently operating processors has created a new environment wherein the above optimization, and other engineering problems heretofore regarded as intractable may be solved. The procedure, shown, is a piecewise approximation based method and involves using a sensitivity based Taylor series approximation model for NVH and a polynomial response surface model for Crash. In that method the NVH constraints are evaluated using a finite element code (MSC/NASTRAN) that yields the constraint values and their derivatives with respect to design variables. The crash constraints are evaluated using the explicit code RADIOSS on the Origin 2000 operating on 256 processors simultaneously to generate data for a polynomial response surface in the design variable domain. The NVH constraints and their derivatives combined with the response surface for the crash constraints form an approximation to the system analysis (surrogate analysis) that enables a cycle of multidisciplinary optimization within move limits. In the inner loop, the NVH sensitivities are recomputed to update the NVH approximation model while keeping the Crash response surface constant. In every outer loop, the Crash response surface approximation is updated, including a gradual increase in the order of the response surface and the response surface extension in the direction of the search. In this optimization task, the NVH discipline has 30 design variables while the crash discipline has 20 design variables. A subset of these design variables (10) are common to both the NVH and crash disciplines. In order to construct a linear response surface for the Crash discipline constraints, a minimum of 21 design points would have to be analyzed using the RADIOSS code. On a single processor in Origin 2000 that amount of computing would require over 9 months! In this work, these runs were carried out concurrently on the Origin 2000 using multiple processors, ranging from 8 to 16, for each crash (RADIOSS) analysis. Another figure shows the wall time required for a single RADIOSS analysis using varying number of processors, as well as provides a comparison of 2 different common data placement procedures within the allotted memories for each analysis. The initial design is an infeasible design with NVH discipline Static Torsion constraint violations of over 10%. The final optimized design is a feasible design with a weight reduction of 15 kg compared to the initial design. This work demonstrates how advanced methodology for optimization combined with the technology of concurrent processing enables applications that until now were out of reach because of very long time-to-solution.

Kodiyalam, Srinivas↗

Synthesis and characterisation of In-doped MnWO{sub 4}-type solid-solutions: Mn{sub 1−3x}In{sub 2x}□{sub x}WO{sub 4} (x=0–0.11)

Substitution of In{sup 3+} for Mn{sup 2+} in MnWO{sub 4}, which is one of the most studied multiferroics, was conducted systematically by solid-state reactions at 1050 °C to obtain a series of Mn{sub (1−3x)}In{sub 2x}□{sub x}WO{sub 4} solid solutions (x=0–0.11; the box indicates vacancy). The successful In-doping could be proven by electron microprobe, and statically disordered structures of this solid solution series were elucidated by Rietveld analyses with X-Ray powder diffraction (XPD) data. Its average structure maintains the space group P2/c at least up to the replacement of 33 at% Mn. The tendency of their unit cells proportionally enlarging with In-doping is an unexpected observation because In{sup 3+} is smaller than Mn{sup 2+}. This could not be explained alone by average atomic bonding distances and angles evaluated from XPD data analyses. Complimentarily, micro-Raman spectra of Mn{sub (1−3x)}In{sub 2x}□{sub x}WO{sub 4} materials feature a hardening of Raman modes due to stronger atomic bonds in W{sub 2}O{sub 4} and WO{sub 2} units with increasing In-doping. This is considered as an inevitable consequence of broken bonding in directly neighbouring Mn–O bonds as the presence of In{sup 3+} in MnWO{sub 4} accompanies the creation of defects at Mn sites. The current study using XRD and micro-Raman suggests the enlarging local space around the bridging oxygen as the reason for the unexpected cell expansion when smaller In{sup 3+} along with defects replace Mn{sup 2+} in MnWO{sub 4}. - Graphical abstract: Despite of substitution of smaller In{sup 3+} for larger Mn{sup 2+}, the In-rich solid solution Mn{sub 0.71(2)}In{sub 0.19(1)}□{sub 0.10}WO{sub 4} undergoes a volume expansion of 0.4% with respect to MnWO{sub 4}. This could be explained by a local space expansion of 0.13% around bridging oxygen at O2 sites, as illustrated by dashed lines for clarity. - Highlights: • Investigation of Mn{sub (1−3x)}In{sub 2x}□{sub x}WO{sub 4} solid solutions (x=0–0.11). • An unexpected lattice expansion by In-doping. • Strong change in local environment around bridging oxygens. • Enhancement of atomic bonds in W{sub 2}O{sub 4} and WO{sub 2} units with increasing In-doping.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dynamic land use implications of rapidly expanding and evolving wind power deployment

Abstract The expansion of wind power poses distinct and varied geographic challenges to a sustainable energy transition. However, current knowledge of its land use impacts and synergies is limited by reliance on static characterizations that overlook the role of turbine technology and plant design in mediating interactions with the environment. Here, we investigate how wind technology development and innovation have shaped landscape interactions with social and ecological systems within the United States and contribute to evolving land area requirements. This work assesses trends in key land use facets of wind power using a holistic set of metrics to establish an evidence base that researchers, technology designers, land use managers, and policymakers can use in envisioning how future wind-intensive energy systems may be jointly optimized for clean energy, social, and environmental objectives. Since 2000, we find dynamic land occupancy patterns and regional trends that are driven by advancing technology and geographic factors. Though most historical U.S. wind deployment has been confined to the temperate grassland biome in the nation’s interior, regional expansion has implicated diverse land use and cover types. A large percentage of the typical wind plant footprint (∼96% to > 99%) is not directly impacted by permanent physical infrastructure, allowing for multiple uses in the spaces between turbines. Surprisingly, turbines are commonly close to built structures. Moreover, rangeland and cropland have supported 93.4% of deployment, highlighting potential synergies with agricultural lands. Despite broadly decreasing capacity densities, offsetting technology improvements have stabilized power densities. Land use intensity, defined as the ratio of direct land usage to lifetime power generation of wind facilities, has also trended downwards. Although continued deployment on disturbed lands, and in close proximity to existing wind facilities and other infrastructure, could minimize the extent of impacts, ambitious decarbonization trajectories may predispose particular biomes to cumulative effects and risks from regional wind power saturation. Increased land-use and sustainability feedback in technology and plant design will be critical to sustainable management of wind power.

17 WIND ENERGY↗