Multimodal Spectroscopic Study of Surface Termination Evolution in Cr 2 TiC 2 T x MXene
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
SEARCH · Search NASA
Results for “surface engineering”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Analysis of backwash settings to maximize net water production in an engineering-scale ultrafiltration system for water reuse
Ultrafiltration (UF) has been widely utilized as water pretreatment for different applications especially in water reuse. The UF system operation is characterized by a filtration phase, where particles accumulate on the membrane surface resulting in an increase in the transmembrane pressure (TMP) and a cleaning phase, where foulants are removed through cleaning cycles including physical backwash and chemical-enhanced backwash (CEB). In this study, data from an engineering-scale UF system treating reclaimed wastewater were used to assess the impact of backwashing on the filtration process. TMP backwash trigger, backwash duration, and CEB frequency were purposely varied for a cycle-by-cycle investigation on the net water production, water recovery, initial operating TMP, and filtration cycle duration. As the TMP backwash trigger was varied between 62 and 145kPa, the maximum net water production (63 m 3 /d) was achieved at 103kPa and water recovery remained relatively constant at approximately 92%. Backwash durations of 45, 65, and 85s were performed where both net water production and water recovery yielded similar results (~63 m 3 /d and ~ 91%) compared with 103kPa TMP backwash trigger. The CEB frequency was also lowered from one every three backwashes (1/3) to 1/6 and 1/12 and resulted in decreased net water production and water recovery while the initial TMP increased. Interestingly, the total number of CEBs remained approximately constant regardless of their frequency. In conclusion, results suggest that CEB is an important fouling control process to maximize water production.
42 ENGINEERING↗
Containment at the Source during Waste Volume Reduction of Large Radioactive Components Using Oxylance High-Temperature Cutting Equipment - 13595
As a waste-volume reduction and management technique, highly contaminated Control Element Drive Mechanism (CEDM) housings were severed from the Reactor Pressure Vessel Head (RPVH) inside the San Onofre Unit 2 primary containment utilizing Oxylance high-temperature cutting equipment and techniques. Presented are relevant data concerning: - Radiological profiles of the RPVH and individual CEDMs; - Design overviews of the engineering controls and the specialized confinement housings; - Utilization of specialized shielding; - Observations of apparent metallurgical-contamination coalescence phenomena at high temperatures resulting in positive control over loose-surface contamination conditions; - General results of radiological and industrial hygiene air sampling and monitoring; - Collective dose and personnel contamination event statistics; - Lessons learned. (author)
12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
Solid phase epitaxial regrowth of (001) anatase titanium dioxide
The growing interest in metal oxide based semiconductor technologies has driven the need to produce high quality epitaxial films of one metal oxide upon another. Largely unrecognized in synthetic efforts is that some metal oxides offer strongly polar surfaces and interfaces that require electrostatic stabilization to avoid a physically implausible divergence in the potential. The present work examines these issues for epitaxial growth of anatase TiO{sub 2} on strontium titanate (001). Solid phase epitaxial regrowth yields only the (001) facet, while direct crystalline growth by atomic layer deposition yields both the (112) and (001). The presence of amorphous TiO{sub 2} during regrowth may provide preferential stabilization for formation of the (001) facet.
36 MATERIALS SCIENCE↗
Open and Close-Packed, Shape-Engineered Polygonal Nanoparticle Metamolecules with Tailorable Fano Resonances
In this study, a top-down lithographic patterning and deposition process is reported for producing nanoparticles (NPs) with well-defined sizes, shapes, and compositions that are often not accessible by wet-chemical synthetic methods. These NPs are ligated and harvested from the substrate surface to prepare colloidal NP dispersions. Using a template-assisted assembly technique, fabricated NPs are driven by capillary forces to assemble into size- and shape-engineered templates and organize into open or close-packed multi-NP structures or NP metamolecules. The sizes and shapes of the NPs and of the templates control the NP number, coordination, interparticle gap size, disorder, and location of defects such as voids in the NP metamolecules. The plasmonic resonances of polygonal-shaped Au NPs are exploited to correlate the structure and optical properties of assembled NP metamolecules. Comparing open and close-packed architectures highlights that introduction of a center NP to form close-packed assemblies supports collective interactions, altering magnetic optical modes and multipolar interactions in Fano resonances. Decreasing the distance between NPs strengthens the plasmonic coupling, and the structural symmetries of the NP metamolecules determine the orientation-dependent scattering response.
77 NANOSCIENCE AND NANOTECHNOLOGY↗
Stimulated geologic hydrogen: from mechanistic control to engineered rock transformation
Geologic hydrogen (GeoH 2 ) generated from subsurface iron-rich rock–water reaction (i.e., serpentinization) is emerging as a promising candidate for the next primary energy source. Yet, accelerating GeoH 2 production from geological to human timescales via enhanced serpentinization remains a formidable scientific and technical challenge. Here, in this Review, we decipher the mechanistic control and explore strategies for accelerating in situ, engineered iron-rich rock transformation into carbon-free GeoH 2 by orders of magnitude. Serpentinization rate is hindered by low porosity and permeability of source rocks, suboptimal temperatures, unfavorable water chemistry, inefficient Fe 2+ -to-Fe 3+ conversion, thermodynamic constraints, and low reactive surface area. While closed-system experiments provide valuable mechanistic insights, open-system conditions with fluid circulation are more crucial for economically viable GeoH 2 production. We assess stimulation techniques from enhanced hydrocarbon and geothermal recovery as tools to be adopted or adapted for increasing reactive surface areas for stimulated GeoH2 production. We estimate that 7.40 × 10 5 to 1.73 × 10 6 million metric tons (Mt) of hydrogen could be engineered over 20 to 50 years from about 10% iron-rich rocks within 10 km depth of continental crust. Enabling GeoH 2 as a viable energy source requires not only advancing scientific frontiers but also forming a global GeoH 2 research network and innovation ecosystem to address the critical scientific, technical, societal, economic, and policy challenges.
08 HYDROGEN↗
FBG Sensor technology to interfacial strain measurement in cfrp-strengthened concrete beam
Fiber-reinforced polymer (FRP) composite materials are very attractive for use in strengthening of civil engineering structures because of their high strength to weight and stiffness to weight ratios, being corrosion free, light weight, and potentially high durability. The requirement for any embedded sensor for monitoring strain in FRP-strengthened concrete structures is that the sensor should not be detrimental to the operational requirement of the strengthened structure. Owing to the compatibility with FRP materials, fiber Bragg grating (FBG) sensor is a good choice for embedding at the interface of the FRP-strengthened concrete structures. As the FBG sensors are more flexible and small size (diameter = 250 μm), it may be easily instrumented at the FRP–concrete interface with sufficient surface preparation and suitable adhesive. This article deals with the issues/methods in application of FBG sensors for interfacial strain measurement of reinforced concrete beams strengthened with carbon fiber-reinforced polymer (CFRP). It also describes the experimental studies which were carried out to identify the initiation and propagation of debonding of CFRP from concrete surface using FBG array sensors.
42 ENGINEERING↗
Characterizing near-surface elemental layering on Mars using gamma-ray spectroscopy: A proof-of-principle experiment
Gamma-ray spectroscopy investigations characterize the chemical composition of planetary surfaces by measuring element-characteristic gamma rays with energies of ~100 keV to ~9 MeV. Over this energy range, the mean free path of a gamma ray varies from about 1 to 25 cm, therefore gamma-ray measurements sample subsurface composition. Many elements emit gamma rays at multiple, often widely spaced energies, so gamma-ray measurements can in principle also be used to identify depth-dependent variations in subsurface composition. We report results from laboratory measurements and radiation transport modeling designed to demonstrate this capability. The laboratory measurements verified the presence of depth-dependent gamma-ray signatures, and were then used to benchmark radiation transport simulations that were used to model realistic Mars-like scenarios. The models indicate that compositionally distinct subsurface deposits, buried to depths of ~80 cm (125 g/cm 2 ), can be identified using gamma-ray measurements. Going beyond identification to characterization (burial depth, relative composition of the layers) of the deposits requires knowledge of the vertical and horizontal variability in the water content of the near-surface surface materials, the local Galactic Cosmic Ray environment (magnitude and energy distribution), the depth-dependent neutron flux, gamma-ray production cross sections, and knowledge of the composition and column density of the atmosphere. The results of our experiments and models provided a basis for examining the utility of using orbiter- and lander-based gamma-ray measurements to identify subsurface deposits on Mars.
42 ENGINEERING↗
Effect of Surface Roughness on Dynamic Stall in Pitching Motion
Dynamic stall plays a critical role in determining the performance and stability of a wide range of fluid-dynamics systems in various engineering applications. This unsteady aerodynamic phenomenon is particularly significant for maneuvering aircraft wings, jet aircraft subjected to gust encounters, helicopter rotor blades, and wind turbine blades [1–3]. The prediction of the dynamic stall vortex (DSV) is challenging due to factors such as unsteady aerodynamics, three-dimensional (3-D) effects, turbulence and flow separation, incoming gust, and surface impact effects [4–6]. Hence, advanced computational techniques and modeling approaches in computational fluid dynamics (CFD) would be required to enhance the accuracy and reliability of DSV predictions in dynamic stall scenarios. In the past, Batther and Lee [7] employed delayed detached eddy simulations (DDES) to understand the flow physics associated with the onset of dynamic stall. Their approach demonstrated that DDES achieves results comparable to those obtained from large-eddy simulations at a reduced computational cost. In another study, Khalifa et al. [8] examined the 3-D aspects of dynamic stall on a NACA 0012 airfoil using DES solvers. In conclusion, the findings underlined the superiority of 3-D simulations over two-dimensional approaches, particularly in predicting the lift coefficient values and capturing dynamic stall stages more precisely.
97 MATHEMATICS AND COMPUTING↗
Broadband surface-enhanced coherent anti-Stokes Raman spectroscopy with high spectral resolution
Both the surface-enhanced Raman spectroscopy (SERS) and coherent anti-Stokes Raman spectroscopy (CARS) are widely used methods in the bio-sensing field for improving the intensity of Raman scattering process. By combining the mechanisms of CARS (coherence and nonlinear process) and SERS (plasmon resonance), a multiplicative enhancement can be achieved through surface-enhanced CARS (SECARS). Besides sensitivity, high specificity with wide spectral bandwidth is also preferred for bio-sensing techniques but not well developed in SECARS setups reported in the literature. A broadband SECARS setup with high sensitivity and high spectral resolution is presented. Rhodamine 6G dye molecules and several biomolecules are used as the model system to benchmark the functionality of the SECARS system in terms of its sensitivity, the lowest detectable concentration, and the spectral resolution. Our setup rendered single-molecule sensitivity with spectral resolution of <35 cm -1 . More than 10 2 times stronger signal-to-noise ratio compared with that of SERS is observed with the detection limit being 10 -9 m. Different from the SECARS systems in the literature, our setup employs a unique graphene-Au pyramids hybrid platform. The graphene in this structure provides additional SERS enhancement and a bio-compatible surface. Finally, this powerful technique could be instrumental in furthering the understanding of various chemical and biological processes.
42 ENGINEERING↗
Metal Oxide Nanoarrays for Chemical Sensing: A Review of Fabrication Methods, Sensing Modes, and Their Inter-correlations
In recent years, engineered nanostructure assemblies such as nanowire arrays have attracted much research attention due to their unique chemical and functional characteristics collectively. The engineered nano-assemblies usually carry the characteristics distinct from bulk as a result of a size effect in their comprised elemental building blocks. The nanoscale size induced high surface-to-volume ratio is a fundamental attribute responsible for various chemical and physical properties required in various technologically important applications such as catalysts and sensors. This review article surveys the latest progress in engineered metal oxide nanostructure arrays, i.e., nanoarrays, for advanced chemical sensors' design and application. It starts with an overview of gaseous chemical sensors followed by surveys of various fabrication methods and routes for metal oxide nanoarrays. Different sensing modes and corresponding applications have been highlighted in the mixed gaseous chemical sensing, which provides new approaches and perspectives to meet the challenges of selective gas sensing, such as the cross-sensitivity and inter-correlation of multiple sensing signals.
36 MATERIALS SCIENCE↗
Investigation of TiN thin film oxidation depending on the substrate temperature at vacuum break
Due to the reduction of the thickness of the layers used in the advanced technology nodes, there is a growing importance of the surface phenomena in the definition of the general properties of the materials. One of the least controlled and understood phenomenon is the oxidation of metals after deposition, at the vacuum break. In this study, the influence of the sample temperature at vacuum break on the oxidation level of TiN deposited by metalorganic chemical vapor deposition is investigated. TiN resistivity appears to be lower for samples which underwent vacuum break at high temperature. Using X-ray photoelectron spectrometry analysis, this change is correlated to the higher oxidation of the TiN layer. Moreover, angle resolved XPS analysis reveals that higher is the temperature at the vacuum break, higher is the surface oxidation of the sample. This surface oxidation is in turn limiting the diffusion of oxygen in the volume of the layer. Additionally, evolution of TiN layers resistivity was monitored in time and it shows that resistivity increases until a plateau is reached after about 10 days, with the lowest temperature at vacuum break resulting in the highest increase, i.e., the resistivity of the sample released to atmosphere at high temperature increased by a factor 1.7 whereas the resistivity of the sample cooled down under vacuum temperature increased by a factor 2.7.
42 ENGINEERING↗
Analysis of tow architecture variability in biaxially braided composite tubes
Spatial deviations in composite braid unit cell dimensions limit mechanical performance and are challenging to model. Full-field measurements of the irregular tow placement in biaxially braided composite tubes were obtained by digital image correlation. Analysis of the reconstructed tow paths showed long-range defects along the hoop direction with short-range defects dominating the biased tow direction. A route toward numerical simulation of the composite response is established by developing a 3D model of the composite using the measured tow trajectories. Finally, a comparison to previously-published triaxial braid results indicates axial tows work to constrain unit cells dimensions along the hoop direction.
3-Dimensional reinforcement↗
Biologically inspired reinforcement using polydopamine of polymer bound composites
Interfacial strength plays a critical role in the mechanical properties of a composite system. In this work, a proven mock high explosive (HE), 5-iodo-2’-deoxyuridine (IDOX) was coated by the adhesive promoting polymer polydopamine (PDA), then formulated with an Estane binder system to form an improved HE mock composite. An extensive comparison study of mechanical properties was performed to determine the effects, if any, of PDA on the composite system. To aid in interpretation of the mechanical test data, neutron reflectometry experiments were performed to determine the thickness and structure of the as deposited PDA films. The mechanical performance of PDA-treated IDOX was then compared to untreated specimens by compression testing in the Brazilian disk geometry. The results strongly suggested that the structure of PDA consists of two layers: one low in density caused by polymer agglomerates attaching to the substrate during polymerization, and the second high in density caused by controlled linear deposition of polydopamine. Finally, the mechanical testing showed that PDA greatly increased the stiffness and yield strength of IDOX based mocks without causing any disruption to the underlying crystal system.
42 ENGINEERING↗
Application of thiolate self-assembled monolayers in selective alcohol oxidation for suppression of Pd catalyst deactivation
Rapid deactivation often reduces the effectiveness of Pt-group catalysts in the low-temperature aerobic oxidation of alcohols. We report the use of thiolate self-assembled monolayers (SAMs) as activity promoters in the liquid-phase oxidation of trans-2-hexen-1-ol (HOL) under low air pressure; the oxidation rate was significantly improved, particularly at high conversion, in contrast to the frequently observed activity decrease induced by SAM modification in hydrogenation reactions. Reaction studies indicated that in the regime of low air pressure, catalyst deactivation was mainly caused by the carbonaceous poisons generated from the reaction product 2-hexenal (HAL). Infrared spectroscopy revealed that HAL produced surface residues on Pd that poisoned the catalyst, hypothetically through decarbonylation and dimerization. This poisoning can be suppressed by the SAM modifiers, in a manner that was controllable by varying thiolate surface coverage through use of either 1-adamantanethiol (AT) or 1-octadecanethiol (C18) SAMs.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Towards standardized nuclear reactors: Seismic isolation and the cost impact of the earthquake load case
We report nuclear energy has a key role to play in global decarbonization. Impediments to the widespread deployment of reactors are their projected high capital cost and levelized cost of energy, and time required to analyze, design, license, construct, and commission them. The earthquake load case is a key cost driver for a new build nuclear plant, because near-surface soils and seismic hazard are different at each site, requiring site-specific analysis, design, engineering, qualification, licensing, and regulatory review, essentially making every design First-of-a-Kind (FoaK). To enable deployment at the scale needed for deep decarbonization, the cost and time impact of the seismic load case must be significantly mitigated, and plants must be standardized. Seismic base isolation has been proven to considerably reduce the earthquake response of structures and equipment but has yet to be applied to a nuclear power plant in the United States, in part because the financial impacts, positive or negative, are not known. Because there are no recent non-proprietary data to characterize the influence of the seismic load case on capital cost, it is difficult to confidently quantify the financial benefits of seismic isolation. Scheme-level designs of two fundamentally different advanced reactor buildings were developed to assemble cost data on the influence of the seismic load case. Both buildings were equipped with three bespoke pieces of safety-related equipment and analyzed for incremented levels of earthquake shaking to quantify the seismic penalty on equipment, in terms of vessel weights and horizontal accelerations. Using analysis results, a questionnaire was developed and transmitted to nuclear utilities, reactor developers, engineers, and equipment suppliers to collect cost data on engineering and fabrication costs for these unique pieces of safety-class equipment. Synthesis of the cost data showed that the seismic load case significantly affects the capital cost (sum of engineering and fabrication cost) of safety-class equipment, with engineering costs being comparable to fabrication costs. Standardization of safety-class equipment is made possible by seismic isolation, that is, equipment designed for minimal seismic robustness can resist earthquake shaking at a site of much higher seismic hazard. The average reduction in the capital cost of the safety-related equipment, enabled by seismic isolation, is a factor of two for FoaK equipment and a factor of five for standardized equipment.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Enhanced Absorption and <1% Spectrum-and-Angle-Averaged Reflection in Tapered Microwire Arrays
Not provided.
Materials Science↗