Search NASA⌕ Search

SEARCH · Search NASA

Results for “DIODE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

High-power low-droop violet semipolar (303{sup ¯}1{sup ¯}) InGaN/GaN light-emitting diodes with thick active layer design

Devices grown on nonpolar and semipolar planes of GaN offer key performance advantages over devices grown on the conventional c-plane, including reduced polarization fields. This allows for a wider design space on semipolar planes for light emitting diodes (LEDs) to address the problem of efficiency droop at high current densities. LED structures with very thick (10–100 nm) InGaN single-quantum-well/double heterostructure active regions were grown using conventional metal organic chemical vapor deposition on semipolar (303{sup ¯}1{sup ¯}) free-standing GaN substrates and processed and packaged using conventional techniques. Simulated band diagrams showed reduced polarization fields on the (303{sup ¯}1{sup ¯}) plane. The calculated critical thickness for misfit dislocation formation is higher on the (303{sup ¯}1{sup ¯}) plane than on other semipolar planes, such as (202{sup ¯}1{sup ¯}), allowing for thicker active regions than our previous work to further reduce droop. The higher critical thickness was confirmed with defect characterization via cathodoluminescence. A trend is demonstrated in lower efficiency droop for devices with thicker active regions. Thermal droop characteristics of these devices are also presented. These observed results were utilized to demonstrate over 1 W of output power at a current density of 1 kA/cm{sup 2} from a single 0.1 mm{sup 2} LED device.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Temperature-dependent efficiency droop of blue InGaN micro-light emitting diodes

Temperature-dependent trends in radiative and Auger recombination coefficients have been determined at different injection carrier concentrations using InGaN micro-light emitting diodes 40 μm in diameter. The differential lifetime was obtained first from the measured modulation bandwidth and was then employed to calculate the carrier concentration in the quantum well active region. When the temperature increases, the carrier concentration increases, but both the radiative and Auger recombination coefficients decrease. In addition, the temperature dependence of radiative and Auger recombination coefficients is weaker at a higher injection carrier concentration, which is strongly related to phase space filling.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Green (In,Ga,Al)P-GaP light-emitting diodes grown on high-index GaAs surfaces

We report on green (550–560 nm) electroluminescence (EL) from (Al{sub 0.5}Ga{sub 0.5}){sub 0.5}In{sub 0.5}P-(Al{sub 0.8}Ga{sub 0.2}){sub 0.5}In{sub 0.5}P double p-i-n heterostructures with monolayer-scale GaP insertions in the cladding layers and light-emitting diodes based thereupon. The structures are grown side-by-side on high-index and (100) GaAs substrates by molecular beam epitaxy. At moderate current densities (∼500 A/cm{sup 2}), the EL intensity of the structures is comparable for all substrate orientations. Opposite to the (100)-grown strictures, the EL spectra of (211) and (311)-grown devices are shifted towards shorter wavelengths (∼550 nm at room temperature). At high current densities (>1 kA/cm{sup 2}), a much higher EL intensity is achieved for the devices grown on high-index substrates. The integrated intensity of (311)-grown structures gradually saturates at current densities above 4 kA/cm{sup 2}, whereas no saturation is revealed for (211)-grown structures up to the current densities above 14 kA/cm{sup 2}. We attribute the effect to the surface orientation-dependent engineering of the GaP band structure, which prevents the escape of the nonequilibrium electrons into the indirect conduction band minima of the p-doped (Al{sub 0.8}Ga{sub 0.2}){sub 0.5}In{sub 0.5}P cladding layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Remarkably reduced efficiency droop by using staircase thin InGaN quantum barriers in InGaN based blue light emitting diodes

The efficiency droop of InGaN/GaN(InGaN) multiple quantum well (MQW) light emitting diodes (LEDs) with thin quantum barriers (QB) is studied. With thin GaN QB (3 nm–6 nm thickness), the efficiency droop is not improved, which indicates that hole transport cannot be significantly enhanced by the thin GaN QBs. On the contrary, the efficiency droop was remarkably reduced by using a InGaN staircase QB (InGaN SC-QB) MQWs structure where InGaN SC-QBs lower the transport energy barrier of holes. The efficiency droop ratio was as low as 3.3% up to 200 A/cm{sup 2} for the InGaN SC-QB LED. By using monitoring QW with longer wavelength we observe a much uniform carrier distribution in the InGaN SC-QB LEDs, which reveals the mechanism of improvement in the efficiency droop.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High-efficiency fluorescent organic light-emitting diodes enabled by triplet-triplet annihilation and horizontal emitter orientation

A green organic light-emitting diode with the fluorescent emitter Coumarin 545T shows an external quantum efficiency (η{sub EQE}) of 6.9%, clearly exceeding the classical limit of 5% for fluorescent emitters. The analysis of the angular dependent photoluminescence spectrum of the emission layer reveals that 86% of the transition dipole moments are horizontally oriented. Furthermore, transient electroluminescence measurements demonstrate the presence of a delayed emission originating from triplet-triplet annihilation. A simulation based efficiency analysis reveals quantitatively the origin for the high η{sub EQE}: a radiative exciton fraction higher than 25% and a light-outcoupling efficiency of nearly 30%.

36 MATERIALS SCIENCE↗

Carrier transport in graphite/Si{sub 3}N{sub 4}-nanobelt/PtIr Schottky barrier diodes

Understanding the roles of contacts and interfaces between metals and semiconductors is critically important for exploring nanostructure-based nanodevices. The present study shed some light on the dominated mechanism of size-dependent carrier transfer in the Schottky barrier diodes configured by the Pt-Ir/Si{sub 3}N{sub 4}-nanobelt/graphite (metal-semiconductor-metal (MSM)) sandwiched structure via a conductive atomic force microscopy using nanobelts with various thicknesses. The observed I-V behaviors suggested that the charge transports under the low and high biases were dominated by the reverse-biased Schottky barrier and space-charge-limited current (SCLC), respectively. The intermediate region between the low and high biases presented the transition between the Ohmic and SCLC behaviors, in which the ≡Si and =N dangling bonds acted as the defects within the Si{sub 3}N{sub 4} nanobelt surface are predominant in the charge transfer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Roles of V-shaped pits on the improvement of quantum efficiency in InGaN/GaN multiple quantum well light-emitting diodes

The roles of V-shaped pits on the improvement of quantum efficiency in InGaN/GaN multiple quantum well (MQW) light-emitting diodes are investigated by numerical simulation. The simulation results show that V-shaped pits cannot only screen dislocations, but also play an important role on promoting hole injection into the MQWs. It is revealed that the injection of holes into the MQW via the sidewalls of the V-shaped pits is easier than via the flat region, due to the lower polarization charge densities in the sidewall structure with lower In concentration and (10–11)-oriented semi-polar facets.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Enhancing optical power of GaN-based light-emitting diodes by nanopatterning on indium tin oxide with tunable fill factor using multiple-exposure nanosphere-lens lithography

In this study, the multiple-exposure nanosphere-lens lithography method utilizing the polystyrene nanospheres with focusing behavior is investigated and introduced to fabricate diverse photonic crystals (PCs) on indium tin oxide to enhance the optical output power of GaN-based light-emitting diode (LED). Simulated results indicate that the focused light intensity decreases with increasing tilted angle due to the shadow effect introduced by adjacent nanospheres. The fill factor of nanopattern is tunable by controlling tilted angles and exposure times. To attain quadruple PC without overlapping patterns, mathematical calculation model is used to define the optimum range of tilted angles. Angular emission patterns and three-dimensional finite-difference time domain simulated results indicate that the enhanced light extraction of PC LEDs results mainly from diffused scattering effects, and the diffraction effects of PC on light extracted efficiency increase with the increase of fill factor. Furthermore, it is confirmed that the multiple PC can extract more light from GaN into air than common PC with same period and fill factor.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Phosphorescence lifetimes of organic light-emitting diodes from two-component time-dependent density functional theory

“Spin-forbidden” transitions are calculated for an eight-membered set of iridium-containing candidate molecules for organic light-emitting diodes (OLEDs) using two-component time-dependent density functional theory. Phosphorescence lifetimes (obtained from averaging over relevant excitations) are compared to experimental data. Assessment of parameters like non-distorted and distorted geometric structures, density functionals, relativistic Hamiltonians, and basis sets was done by a thorough study for Ir(ppy){sub 3} focussing not only on averaged phosphorescence lifetimes, but also on the agreement of the triplet substate structure with experimental data. The most favorable methods were applied to an eight-membered test set of OLED candidate molecules; Boltzmann-averaged phosphorescence lifetimes were investigated concerning the convergence with the number of excited states and the changes when including solvent effects. Finally, a simple model for sorting out molecules with long averaged phosphorescence lifetimes is developed by visual inspection of computationally easily achievable one-component frontier orbitals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Recoverable degradation of blue InGaN-based light emitting diodes submitted to 3 MeV proton irradiation

This paper reports on the degradation and recovery of two different series of commercially available InGaN-based blue light emitting diodes submitted to proton irradiation at 3 MeV and various fluences (10{sup 11}, 10{sup 13}, and 10{sup 14} p{sup +}/cm{sup 2}). After irradiation, we detected (i) an increase in the series resistance, in the sub-turn-on current and in the ideality factor, (ii) a spatially uniform drop of the output optical power, proportional to fluence, and (iii) a reduction of the capacitance of the devices. These results suggest that irradiation induced the generation of non-radiative recombination centers near the active region. This hypothesis is further confirmed by the results of the recovery tests carried out at low temperature (150 °C)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Direct transparent electrode patterning on layered GaN substrate by screen printing of indium tin oxide nanoparticle ink for Eu-doped GaN red light-emitting diode

Transparent electrodes were formed on Eu-doped GaN-based red-light-emitting diode (GaN:Eu LED) substrates by the screen printing of indium tin oxide nanoparticle (ITO np) inks as a wet process. The ITO nps with a mean diameter of 25 nm were synthesized by the controlled thermolysis of a mixture of indium complexes and tin complexes. After the direct screen printing of ITO np inks on GaN:Eu LED substrates and sintering at 850 °C for 10 min under atmospheric conditions, the resistivity of the ITO film was 5.2 mΩ cm. The fabricated LED up to 3 mm square surface emitted red light when the on-voltage was exceeded.

36 MATERIALS SCIENCE↗

High light extraction efficiency in bulk-GaN based volumetric violet light-emitting diodes

We report on the light extraction efficiency of III-Nitride violet light-emitting diodes with a volumetric flip-chip architecture. We introduce an accurate optical model to account for light extraction. We fabricate a series of devices with varying optical configurations and fit their measured performance with our model. We show the importance of second-order optical effects like photon recycling and residual surface roughness to account for data. We conclude that our devices reach an extraction efficiency of 89%.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The effect of the hole injection layer on the performance of single layer organic light-emitting diodes

Efficient single-layer organic light-emitting diodes (OLEDs) were reported based on a green fluorescent dye 10-(2-benzothiazolyl)-2,3,6,7-tetrahydro-1,1,7,7–tetramethyl-1H,5H,11H-(1) benzopyropyrano (6,7-8-I,j)quinolizin-11-one (C545T). Herein, poly(3,4-ethylenedioxy thiophene) poly(styrene sulfonate) were, respectively, applied as the injection layer for comparison. The hole transport properties of the emission layer with different hole injection materials are well investigated via current-voltage measurement. It was clearly found that the hole injection layers (HILs) play an important role in the adjustment of the electron/hole injection to attain transport balance of charge carriers in the single emission layer of OLEDs with electron-transporting host. The layer of tris-(8-hydroxyquinoline) aluminum played a dual role of host and electron-transporting materials within the emission layer. Therefore, appropriate selection of hole injection layer is a key factor to achieve high efficiency OLEDs with single emission layer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Exciton quenching at PEDOT:PSS anode in polymer blue-light-emitting diodes

The quenching of excitons at the poly(3,4-ethylenedioxythiophene):poly(styrenesulfonic acid) (PEDOT:PSS) anode in blue polyalkoxyspirobifluorene-arylamine polymer light-emitting diodes is investigated. Due to the combination of a higher electron mobility and the presence of electron traps, the recombination zone shifts from the cathode to the anode with increasing voltage. The exciton quenching at the anode at higher voltages leads to an efficiency roll-off. The voltage dependence of the luminous efficiency is reproduced by a drift-diffusion model under the condition that quenching of excitons at the PEDOT:PSS anode and metallic cathode is of equal strength. Experimentally, the efficiency roll-off at high voltages due to anode quenching is eliminated by the use of an electron-blocking layer between the anode and the light-emitting polymer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electrically injected near-infrared light emission from single InN nanowire p-i-n diode

We report on the achievement of electroluminescence emission of single InN p-i-n nanowire devices. InN p-i-n nanowire structures were grown directly on Si substrate by plasma-assisted molecular beam epitaxy and subsequently transferred to foreign substrate for the fabrication of single nanowire light emitting diodes. Electroluminescence emission with a peak energy of 0.71 eV (1.75 μm) was observed at 77 K. The measurement of near-bandgap electroluminescence provides unambiguous evidence for the achievement of p-type conduction of InN.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Enhanced emission from mid-infrared AlInSb light-emitting diodes with p-type contact grid geometry

We report on the impact of lateral current spreading on light emission from aluminium indium antimonide (AlInSb) mid-infrared p-i-n light-emitting diodes (LEDs) grown by molecular beam epitaxy on a GaAs substrate. Due to the high effective mass of holes in Al{sub x}In{sub 1−x}Sb, the resistivity of p-type material determines the 3-D distribution of current flow in the devices. This work shows that maximum light emission, as measured by electroluminescence, and 3-times wall-plug efficiency improvement were obtained at room temperature from devices with a p-type contact grid geometry with a spacing of twice the current spreading length in the p-type material, which was measured by spatially resolved photocurrent. The LED with the optimal contact geometry exhibits improved performance at high injection current levels thanks to the more uniform carrier distribution across the device area.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Luminescent properties of Eu{sup 2+}-doped BaGdF{sub 5} glass ceramics a potential blue phosphor for ultra-violet light-emitting diode

Eu{sup 2+} doped transparent oxyfluoride glass ceramics containing BaGdF{sub 5} nanocrystals were successfully fabricated by melt-quenching technique under a reductive atmosphere. The structure of the glass and glass ceramics were investigated by differential scanning calorimetry, X-ray diffraction (XRD), and transmission electron microscopy (TEM). The luminescent properties were investigated by transmission, excitation, and emission spectra. The decay time of the Gd{sup 3+} ions at 312 nm excited with 275 nm were also investigated. The results of XRD and TEM indicated the existence of BaGdF5 nanocrystals in the transparent glass ceramics. The excitation spectra of Eu{sup 2+} doped glass ceramics showed an excellent overlap with the main emission region of an ultraviolet light-emitting diode (UV-LED). Compared with the as-made glass, the emission of glass ceramics is much stronger by a factor of increasing energy transfer efficiency from Gd{sup 3+} to Eu{sup 2+} ions, the energy transfer efficiency from Gd{sup 3+} to Eu{sup 2+} ions was discussed. In addition, the chromaticity coordinates of glass and glass ceramics specimens were also discussed, which indicated that the Eu{sup 2+} doped BaGdF{sub 5} glass ceramics may be used as a potential blue-emitting phosphor for UV-LED.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Acceptor impurity activation in III-nitride light emitting diodes

In this work, the role of the acceptor doping and the acceptor activation and its impact on the internal quantum efficiency (IQE) of a Gallium Nitride (GaN) based multi-quantum well light emitting diode is studied by microscopic simulation. Acceptor impurities in GaN are subject to a high activation energy which depends on the presence of proximate dopant atoms and the electric field. A combined model for the dopant ionization and activation barrier reduction has been developed and implemented in a semiconductor carrier transport simulator. By model calculations, we demonstrate the impact of the acceptor activation mechanisms on the decay of the IQE at high current densities, which is known as the efficiency droop. A major contributor to the droop is the electron leakage which is largely affected by the acceptor doping.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗