SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A fan-driven transonic cryogenic tunnel was designed, and its purging, cooldown, and warmup times were determined satisfactory. Cooling with liquid nitrogen is at the power levels required for transonic testing. Good temperature distributions are obtained by using a simple nitrogen injection system.
The constraints that any plausible thermal model of the moon should fulfill are reviewed, and the shortcomings exhibited by models so far proposed are pointed out. A model satisfying the constraints is suggested. It involves a giant impact on the temperature distribution of the moon.
Elastic wave velocities of two Apollo 14 rocks, 14053 and 14321, three Apollo 15 rocks, 15058, 15415, and 15545, and one Apollo 16 rock 60315 have been determined at pressures up to 10 kb. For sample 14321, the variation of the compressional wave velocities with temperature has been measured over the temperature range from 27 to 200 C. Overall elastic properties of these samples except sample 15415 are very similar to those of Apollo 11, 12, and 14 rocks and are concordant with Toksoz et al.'s (1972) interpretation that lunar upper crust is of basaltic composition. Temperature derivative of the P wave velocity for sample 14321 is a half to one order of magnitude larger than that for single crystalline minerals. This suggests that the seismic velocity in the lunar crust may be affected significantly by the temperature distribution.
The design of cooled skin panels, which requires consideration of many parameters such as heat load, skin thickness, panel size, tube spacing, tube size, temperature limits, coolant flow, etc., must minimize weight and thermal stresses. A design procedure for such panels has been developed by Bell Aerospace Company (Helenbrook and Anthony, 1971). This design procedure assumes a uniform heating rate to the panel, i.e., the variation of aerodynamic heating rate due to the cyclic wall temperature distribution, which results from the discrete coolant tube locations in such a panel, has been neglected. This study was made to determine if these variations were sufficiently large to cause variations in aerodynamic heating rate which would require coupling of boundary layer and conductive thermal analysis solutions.
It is pointed out that the lunar magnetometer experiment has made important contributions to studies of the lunar interior. Numerical inversions of the lunar electromagnetic response have been carried out, taking into account a void region behind the moon. The amplitude of the transfer function of an eight-layer model is considered along with a model of the temperature distribution inside the moon and the amplitude of the transfer function of a semiconductor lunar model.
Derivation of a model for the chromosphere and upper photosphere of Procyon (F5 IV-V) based on calibrated observations of the K and 8542-A lines of Ca II, the k(2796-A) line of Mg II, and the K-line wings. The feasibility of this model synthesis approach to derive a preliminary model chromosphere is demonstrated despite the lack of spatial and spectral resolution associated with solar chromospheric studies. The proposed upper photosphere model is very similar to the radiative equilibrium Procyon model of Strom and Kurucz (1966), while the proposed chromospheric model is similar to the quiet solar chromosphere temperature distribution of Shine (1973) in the 6000 to 8000 K range.
Tests were conducted to determine the net heat leak to a source of liquid nitrogen caused by a metal penetration through the blanket of multilayer insulation. The conditions under which the tests were conducted are described. A graph of the theoretical and experimental temperature distribution is developed for comparison. The variables involved in the computer program to process the data are defined. A study was conducted to develop analytical methods for predicting the effect and magnitudes of thermoacoustic oscillations on the penetration heat leak to cryogens. The oscillations develop as a result of large thermal gradients imposed on a compressible fluid. The predominant amplitudes and frequencies of the thermal acoustic oscillations were investigated.
A parametric study of the heat transfer rate along the wall of a rocket nozzle is presented. The influences of different parameters; laminar and turbulent Lewis number, mixture ratio, initial wall temperature distribution, and eddy viscosity, were considered. The numerical evaluation of these influences on heat transfer rate was done by using three different compressible, reacting laminar and turbulent boundary layer computer programs; MABL (Mass Addition Boundary Layer Program), MABL-KE (MABL program is modified to include turbulent kinetic energy equation), and BLIMP (Boundary Layer Integral Matrix Procedure). This study also provided an excellent opportunity to evaluate the efficiencies of these three computer programs and to suggest one of them for future computational purposes.
The author has identified the following significant results. Successful tentative calibration permits computer programs to be written to convert Skylab thermal tapes into line-printed graymaps showing actual surface radiation temperature distributions at the time of imaging. The calibrations will be further checked when atmospheric soundings are available. Success of Skylab calibration suggests that satellite are feasible platforms for thermal scanning and provide a much broader geographical field of view than is possible with airborne platforms.
A lumped parameter thermal nodal network was developed for a 30 cm Engineering Model Mercury Ion Thruster. The network consists of approximately 100 nodes coded in SINDA format for use on the Univac 1106/1108 computer. This model takes into account internal dissipation, radiation, and conduction as well as environmental heating. A series of tests were performed to simulate a wide range of thermal environments on an operating 30 cm thruster, instrumented to measure the temperature distribution within the thruster. The results of these tests were used to calibrate the analytical model. The analytical model along with comparisons between analytical and experimental results for the various operating conditions are presented.
Data obtained on a VCHP heat-pipe radiator system tested in a vacuum environment were studied. Analyses and interpretation of the steady-state results are presented along with an initial analysis of some of the transient data. Particular emphasis was placed on quantitative comparisons of the experimental data with computer model simulations. The results of the study provide a better understanding of the system but do not provide a complete explanation for the observed low VCHP performance and the relatively flat radiator panel temperature distribution. The results of the study also suggest hardware, software, and testing improvements.
Absorption of solar radiation by sea water with contact heat exchange and evaporation leads to the formation of a thin cold film on the ocean surface. Microconvection to ice in this thin surface layer is attributed to nonuniform temperature distributions in wind and water and irregular drag by the air currents.
Comparative steady state nonlinear thermal analyses of a scramjet fuel injection strut are presented. The analyses were performed using the NASTRAN finite element program and MITAS, a lumped-parameter thermal analyzer. The strut is subjected to aerodynamic heating on two sides and is internally cooled by hydrogen flowing from internal manifolds through heat exchangers bonded to the primary structure. Based on coolant temperatures determined by MITAS, NASTRAN predicted temperature distributions throughout the strut which were in close agreement with similar MITAS predictions.
A lumped parameter thermal nodal network has been developed for a 30 cm engineering model mercury ion thruster. The network consists of approximately 100 nodes coded in SINDA format for use on the Univac 1106/1108 computer. This model takes into account internal dissipation, radiation, and conduction as well as environmental heating. A series of tests were performed at NASA-Lewis Research Center to simulate a wide range of thermal environments on an operating 30 cm thruster, instrumented to measure the temperature distribution within the thruster. The results of these tests were used to calibrate the analytical model. Presented in this paper are a description of the analytical model along with comparisons between analytical and experimental results for the various operating conditions.
Techniques for recovering atmospheric refractivity profiles from simulated satellite-to-satellite tracking data are documented. Examples are given using the geometric configuration of the ATS-6/NIMBUS-6 Tracking Experiment. The underlying refractivity model for the lower atmosphere has the spherically symmetric form N = exp P(s) where P(s) is a polynomial in the normalized height s. For the simulation used, the Herglotz-Wiechert technique recovered values which were 0.4% and 40% different from the input values at the surface and at a height of 33 kilometers, respectively. Using the same input data, the model fitting technique recovered refractivity values 0.05% and 1% different from the input values at the surface and at a height of 50 kilometers, respectively. It is also shown that if ionospheric and water vapor effects can be properly modelled or effectively removed from the data, pressure and temperature distributions can be obtained.
A flightweight panel based on a metallic thermal-protection-system concept for hypersonic and reentry vehicles was subjected repeatedly to thermal cycling by quartz-lamp radiant heating using a thermal history representative of a reentry heat pulse and to aerodynamic heating at heating rates required to sustain a surface temperature of 1089 K (1960 R). The panel consisted of a corrugated heat shield and support members of 0.05-cm (0.02-in.) thick Rene 41 of riveted construction and 5.08-cm (2-in.) thick silica fibrous insulation packages covered by Rene 41 foil and inconel screening. All tests were conducted in the Langley 8-foot high-temperature structures tunnel with the heat shield corrugations alined in the stream direction. The panel sustained 5.33 hr of intermittent radiant heating and 6.5 min of intermittent aerodynamic heating of up to 1-min duration for differential pressures up to 6.2 kPa (0.9 psi) with no apparent degradation of thermal or structural integrity, as indicated by temperature distributions and results from load deflection tests and vibration surveys of natural frequencies.
The technical feasibility is studied of growing single-crystal silicon ribbon in the space environment. Procedures are described for calculating the electromagnetic fields produced in a silicon ribbon by an rf shaping coil. The forces on the ribbon and the degree of shaping to be expected are determined. The expected steady-state temperature distribution in the ribbon is calculated in the one-dimensional approximation. Calculations on simplified models indicate, that lack of flatness of the shaped ribbon and excessive heating of the melt by the eddy currents induced by the shaping fields may pose problems. An analysis of the relative effects of various kinds of forces other than electromagnetic showed that in the space environment capillarity forces would dominate, and that the shape of the melt is thus principally determined by the shape of any solids with which it comes in contact. This suggests that ribbon may be produced simply by drawing between parallel wires. A concept is developed for a process of off-angle growth, in which the ribbon is pulled at an angle to the solidification front. Such a process promises to offer increased growth rate, better homogeneity, and thinner ribbon.
Radiation pyrometry principles and imaging methods like photography and photoelectric scanning are combined to make accurate research quality temperature measurements on turbine airfoils. Two systems are described for obtaining detailed temperature distribution measurements: an infrared photographic system for stationary vanes and a photoelectric scanning system for rotating blades. An overview is presented outlining the design, calibration methods, and recent test results.