Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inlets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Predicted upwash angles at engine inlets for STOL aircraft

Upwash angles were predicted for a STOL lifting system by using a two-dimensional potential flow analysis. Upwash angles are presented for distances ahead of the wing leading edge of 50, 75, and 100 percent of wing chord. The upwash angle was determined to be insensitive to the vertical location of the engine inlet. For a wide range of takeoff and landing conditions, the upwash angle was found to be a function of the total two-dimensional lift coefficient. Upwash angles, along with typical flow fields, are presented for a range of total two-dimensional lift coefficients from 2 to 12. Three-dimensional effects were considered in estimating upwash angles for an unswept-wing externally blown flap aircraft. For this STOL configuration, effective upwash angles during takeoff, approach, and waveoff conditions were found to be 22 deg, 26 deg, and 36 deg, respectively.

Albers, J. A.↗
NASA NTRS1972

Performance estimates for a supersonic axisymmetric inlet system.

Results of recent tests of a large-scale axisymmetric mixed-compression inlet system designed for Mach number 2.65 indicate that the performance of the supersonic diffuser and required boundary-layer bleed system can be accurately estimated with relatively new analytic methods. Thus, many wind tunnel testing hours can be saved by avoiding much of the usual ?cut and try' wind tunnel development.

Sorensen, N. E.↗
NASA NTRS1972

Flight investigation of an underwing nacelle installation of an auxiliary-inlet ejector nozzle with a clamshell flow diverter from Mach 0.6 to 1.3

A nozzle installation of general interest is a podded engine mounted near the aft lower surface of the wing. The effect of this installation on the performance of an auxiliary-inlet ejector nozzle with a clamshell flow diverter was investigated over a Mach number range of 0.6 to 1.3 by using a modified F-106B aircraft. The clamshell flow diverter was tested in a 17 deg position with double-hinged synchronized floating doors. The ejector nozzle trailing-edge flaps were simulated in the closed position with a rigid structure which provided a boattail angle of 10 deg. Primary nozzle area was varied as exhaust gas temperature was varied between 975 and 1561 K. With the nozzle in a subsonic cruise position, the nozzle gross thrust coefficient was 0.918 at a flight Mach number of 0.9.

Head, V. L.↗
NASA NTRS1973

Design of a bleed system for a Mach 3.5 inlet

An analytical bleed system design procedure is applied to a Mach 3.5, axisymmetric, translating centerbody inlet. The design features a traveling centerbody bleed system with a ducting arrangement separating low-, medium-, and high-pressure bleed. Three forward plenums and nine throat plenums are installed on the centerbody to meet the bleed requirements in the started Mach range between 1.6 and 3.5. The cowl contains four stationary plenums, three for forward and one for throat bleed. To achieve maximum bleed plenum pressure and thereby minimize bleed drag all bleed holes are inclined 20 deg to the surface except in the cowl throat region. Here the requirement of high stability margin with minimum total pressure recovery penalty resulted in 90 deg bleed holes. The bleed hole diameter varies from bleed plenum to bleed plenum to achieve the most efficient boundary layer control, while the bleed exits are sized to operate at the highest possible plenum pressure without unchoking the bleed holes. Bleed flow rates, bleed plenum pressures, and boundary layer development along the cowl and centerbody are predicted over the entire started Mach range.

Syberg, J.↗
NASA NTRS1973

The effect of nozzle inlet shape, lip thickness, and exit shape and size on subsonic jet noise

Far field noise data were taken for convergent nozzles of various shapes and sizes at subsonic velocities exceeding 400 feet per second. For a circular nozzle, the nozzle inlet shape and lip thickness had no effect on the noise level, directivity, or spectra when compared at the same nozzle exit diameter and peak exhaust velocity. A sharp edged orifice was one exception to this statement. Coannular nozzles can produce additional high frequency noise. Blunt ended centerbodies, where there is significant base drag, also generate significant additional noise. The total noise power generation was essentially the same for circular, slot, and plug nozzles of good aerodynamic shape. The noise radiation patterns were essentially the same for these nozzle shapes except near the nozzle exhaust axis.

Olsen, W. A.↗
NASA NTRS1973

Effect of reducing rotor blade inlet diameter on the performance of a 11.66-Centimeter radial-inflow turbine

The effect of increased rotor blade loading on turbine performance was investigated by reducing rotor blade inlet diameter. The reduction was made in four stages. Each modification was tested with the same stator using cold air as the working fluid. Results are presented in terms of equivalent mass flow and efficiency at equivalent design rotative speed and over a range of pressure ratios. Internal flow characteristics are shown in terms of stator exit static pressure and the radial variation of local loss and rotor-exit flow angle with radius ratio. Included are velocity diagrams calculated from the experimental results.

Kofskey, M. G.↗
NASA NTRS1972

Effects of vane-induced rotation on diffuser flow distortion in an axisymmetric mixed-compression inlet

An investigation of vane-induced flow rotation to modify distorted steady-state total-pressure patterns in the subsonic diffuser of a supersonic mixed-compression inlet was conducted. Radial static-pressure gradients generated by the rotation was the mechanism used to modify the total-pressure distributions. Significant redistribution of circumferential distortion patterns into more compatible radial patterns was realized, but flow problems near the duct walls reduced the general effectiveness of the technique. Total-pressure losses associated with the swirl vanes were slight. Limited turbulence data indicated that vane istallation resulted in reduced turbulence levels.

Meleason, E. T.↗
NASA NTRS1973

Afterburner Performance of Circular V-Gutters and a Sector of Parallel V-Gutters for a Range of Inlet Temperatures to 1255 K (1800 F)

Combustion tests of two V-gutter types were conducted in a 19.25-in. diameter duct using vitiated air. Fuel spraybars were mounted in line with the V-gutters. Combustor length was set by flame-quench water sprays which were part of a calorimeter for measuring combustion efficiency. Although the levels of performance of the parallel and circular array afterburners were different, the trends with geometry variations were consistent. Therefore, parallel arrays can be used for evaluating V-gutter geometry effects on combustion performance. For both arrays, the highest inlet temperature produced combustion efficiencies near 100 percent. A 5-in. spraybar - to - V-gutter spacing gave higher efficiency and better lean blowout performance than a spacing twice as large. Gutter durability was good.

Brandstetter, J. Robert↗
NASA NTRS1973

Analysis of inlet flow distortion and turbulence effects on compressor stability

The effect of steady state circumferential total pressure distortion on the loss in compressor stall pressure ratio has been established by analytical techniques. Full scale engine and compressor/fan component test data were used to provide direct evaluation of the analysis. Specifically, since a circumferential total pressure distortion in an inlet system will result in unsteady flow in the coordinate system of the rotor blades, analysis of this type distortion must be performed from an unsteady aerodynamic point of view. By application of the fundamental aerothermodynamic laws to the inlet/compressor system, parameters important in the design of such a system for compatible operation have been identified. A time constant, directly related to the compressor rotor chord, was found to be significant, indicating compressor sensitivity to circumferential distortion is directly dependent on the rotor chord.

Melick, H. C., Jr.↗
NASA NTRS1973

Investigation of the effect of inlet turbulence length scale on fan discrete tone noise

Results of an experimental investigation at the Ames 40- by 80-Foot Wind Tunnel of fan rotor alone discrete tone noise is presented. The investigation examines rotor interaction with fan inlet turbulence. The importance of turbulence length scale is shown by comparing the fan radiated acoustic spectrum with and without modified turbulence length scales. A small-scale low pressure ratio fan was used for the experiment.

Hodder, B. K.↗
NASA NTRS1973

Experimental investigation of a large-scale, two-dimensional, mixed-compression inlet system: Internal performance and drag at transonic conditions, free stream Mach equals 0.6 to 1.28

A large scale, variable-geometry inlet system with a design Mach number of 3.0 was tested at Mach numbers from 0.6 to 1.28. Variable features for off-design operation are an adjustable-height ramp system and a translating cowl. Experimental results are presented for transonic ramp and cowl positions showing the effect of throat boundary layer bleed and vortex generators on engine-face performance. Detailed pressure and force-balance data are used to evaluate transonic drag characteristics.

Wong, N. D.↗
NASA NTRS1973

The effects of inlet temperature and pressure distortion on turbojet performance

The effects on stability of steady-state, 180 degree extent circumferential distortions of inlet total temperature and pressure were experimentally determined for a turbojet engine. Results for both individual and combined temperature and pressure distortions are presented showing the losses incurred in stall pressure ratio and are compared with results predicted using a simplified parallel compressor model. The loss due to combined distortions was dependent upon the relative orientation between the low pressure and high temperature regions. Reasonable agreement was achieved between the predicted and observed loss in stall pressure ratio when based on a constant corrected speed relationship.

Braithwaite, W. M.↗
NASA NTRS1973

The effect of nozzle inlet shape, lip thickness, and exit shape and size on subsonic jet noise.

Far field noise data were taken for convergent nozzles of various shapes and sizes at subsonic velocities exceeding 400 ft/sec. For a circular nozzle, the nozzle inlet shape and lip thickness had no effect on the noise level, directivity, or spectra when compared at the same nozzle exit diameter and peak exhaust velocity. A sharp edged orifice was one exception to this statement. Coannular nozzles can produce additional high frequency noise. Blunt ended centerbodies, where there is significant base drag, also generate significant additional noise.

Olsen, W. A.↗
NASA NTRS1973

Spontaneous ignition in afterburner segment tests at an inlet temperature of 1240 K and a pressure of 1 atmosphere with ASTM jet-A fuel

A brief testing program was undertaken to determine if spontaneous ignition and stable combustion could be obtained in a jet engine afterburning operating with an inlet temperature of 1240 K and a pressure of 1 atmosphere with ASTM Jet-A fuel. Spontaneous ignition with 100-percent combustion efficiency and stable burning was obtained using water-cooled fuel spraybars as flameholders.

Schultz, D. F.↗