Search NASA⌕ Search

SEARCH · Search NASA

Results for “Level density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Memory implications of the spin-value effect in soft multilayers

New multilayer permalloy materials with thin separation layers that have significantly increased M-R coefficients at room temperature have the potential for substantially increasing both the speed and density of M-R memories. An analysis in the following discussion shows that the bit density at a given performance level is related to the product of M-R response and sheet resistivity when operating at the current-density limit. With a doubling of both sheet resistivity and M-R response over existing materials, the bit area can be reduced by about a factor of 4. Alternatively, if the bit area is kept the same, signal output is increased by a factor of 4 and circuit time constants can be reduced by a factor of 16.

Pohm, A. V.↗

Radio observations of peculiar emission-line Algol binary stars

Twelve peculiar emission-line Algol (PELA) binaries were observed at cm wavelengths. Six of these objects, WW And (tentative), KX And, AM Aur, V644 Mon, DN Ori, and AY Per were detected at the 100 to 400 micro-Jy level, corresponding to luminosity densities of order 10 exp 17 erg/s/Hz. These luminosity densities, combined with nearly flat cm spectra and high brightness temperatures, are consistent with the nonthermal gyrosynchrotron radiation model proposed as the result of observations from the previous PELA survey. Also, the star V367 Cyg was reobserved at thirteen different orbital phases; no variability was found within the errors. V367 Cyg's lack of variability and well-determined average spectral index, however, imply the possibility of a different emission mechanism, thermal bremsstrahlung, although the nonthermal model cannot be entirely ruled out. The characteristic brightness temperature of thermal bremsstrahlung is only about 10,000 K, which means that the radius of the emission region would have to be much larger than previously assumed, about 10 AU. Suggestions for further observations of all previously observed PELAS are presented in order to determine the correct emission mechanism.

Elias, Nicholas M., II↗

Calibration and Lag of a Friez Type Cup Anemometer

Tests on a Friez type cup anemometer have been made in the variable density wind tunnel of the Langley Memorial Aeronautical Laboratory to calibrate the instrument and to determine its suitability for velocity measurements of wind gusts. The instrument was calibrated against a Pitot-static tube placed directly above the anemometer at air densities corresponding to sea level, and to an altitude of approximately 6000 feet. Air-speed acceleration tests were made to determine the lag in the instrument reading. The calibration results indicate that there should be an altitude correction. It is concluded that the cup anemometer is too sluggish for velocity measurements of wind gusts.

INSTRUMENTS - ANEMOMETERS - FRIEZ↗

High amplitude waves in the expanding solar wind plasma

We simulated the 1-D nonlinear time-evolution of high-amplitude Alfven, slow and fast magnetoacoustic waves in the solar wind propagating outward at different angles to the mean magnetic (spiral) field, using the expanding box model. The simulation results for Alfven waves and fast magnetoacustic waves fit the observational constraints in the solar wind best, showing decreasing trends for energies and other rms-quantities due to expansion and the appearance of inward propagating waves as minor species in the wind. Inward propagating waves are generated by reflection of Alfven waves propagating at large angles to the magnetic field or they coincide with the occurrence of compressible fluctuations. In our simulations, fast and slow magnetoacoustic waves seem to have a level in the density-fluctuations which is too high when we compare with the observations. Furthermore, the evolution of energies for slow magnetoacoustic waves differs strongly from the evolution of fluctuation energies in situ.

Schmidt, J. M.↗

Applications of Power Spectral Analysis Methods to Maneuver Loads Obtained on Jet Fighter Airplanes During Service Operations

Power spectral densities of normal load factor have been obtained for two service operational training flights of a Republic F-84G airplane and three service operational training flights of a North American F-86A airplane in order to indicate the load-factor frequency content and possible uses of power spectral methods in analyzing maneuver load data. It was determined that the maneuvering load-factor time histories appeared to be described by a truncated normal distribution. The power spectral densities obtained were relatively level at frequencies below 0.03 cycle per second and varied inversely with approximately the cube of the frequency at the higher frequencies. In general, the frequency content was very low above 0.2 cycle per second. The load-factor peak distributions were estimated fairly well from the spectrum analysis. In addition, peak load data obtained during service operations of fighter-type airplanes with flight time totaling about 24,000 hours were examined and appeared to agree reasonably well with the type of equations obtained from spectrum peak-load distributions.

Mayer, John P.↗

Research Lasers and Air Traffic Safety: Issues, Concerns and Responsibilities of the Research Community

The subject of outdoor use of lasers relative to air traffic has become a diverse and dynamic topic. During the past several decades, the use of lasers in outdoor research activities have increased significantly. Increases in the outdoor use of lasers and increases in air traffic densities have changed the levels of risk involved. To date there have been no documented incidents of air traffic interference from research lasers; however, incidents involving display lasers have shown a marked increase. As a result of the national response to these incidents, new concerns over lasers have arisen. Through the efforts of the SAE G-10T Laser Safety Hazards Subcommittee and the ANSI Z136.6 development committee, potential detrimental effects to air traffic beyond the traditional eye damage concerns have been identified. An increased emphasis from the Federal Aviation Administration (FAA), the Center for Devices and Radiological Hazards (CDRH), and the National Transportation Safety Board (NTSB) along with increased concern by the public have resulted in focused scrutiny of potential hazards presented by lasers. The research community needs to rethink the traditional methods of risk evaluation and application of protective measures. The best current approach to assure adequate protection of air traffic is the application of viable hazard and risk analysis and the use of validated protective measures. Standards making efforts and regulatory development must be supported by the research community to assure that reasonable measures are developed. Without input, standards and regulations can be developed that are not compatible with the needs of the research community. Finally, support is needed for the continued development and validation of protective measures.

Nessler, Phillip J., Jr.↗

Correlations Between Topex Altimeter and Temperature Profile Data in the Equatorial Pacific

Observations of sea-surface heights from satellite altimeters have been a major contributor to monitoring the evolution of the recent major El Nino event. Assimilating altimeter data directly into numerical models only takes advantage of the surface signature provided by the data. However, that surface signature is usually indicative of processes occurring at depth, especially in the equatorial Pacific. In order for assimilation schemes to make maximum use of surface data, it is helpful to have knowledge of how to best extend that data in the vertical to account for that variability. Toward that end, the vertical correlation structure between satellite-observed sea-surface heights and in situ temperature measurements is examined using TOPEX altimeter and TOGA TAO profile data for the period 1993-1998. This time period includes several states of the tropical Pacific, including a perturbed state from 1993-1994, a quiescent state encompassing 1995-1996, and the major ENSO event of 1997-1998. Analyses for each of these periods, as well as the total period will be presented. In addition to analyses at specific depth levels, analyses for particular density surfaces will also be presented.

Adamec, David↗

The Calculation of Accurate Harmonic Frequencies of Large Molecules: The Polycyclic Aromatic Hydrocarbons, a Case Study

The vibrational frequencies and infrared intensities of naphthalene neutral and cation are studied at the self-consistent-field (SCF), second-order Moller-Plesset (MP2), and density functional theory (DFT) levels using a variety of one-particle basis sets. Very accurate frequencies can be obtained at the DFT level in conjunction with large basis sets if they are scaled with two factors, one for the C-H stretches and a second for all other modes. We also find remarkably good agreement at the B3LYP/4-31G level using only one scale factor. Unlike the neutral PAHs where all methods do reasonably well for the intensities, only the DFT results are accurate for the PAH cations. The failure of the SCF and MP2 methods is caused by symmetry breaking and an inability to describe charge delocalization. We present several interesting cases of symmetry breaking in this study. An assessment is made as to whether an ensemble of PAH neutrals or cations could account for the unidentified infrared bands observed in many astronomical sources.

Bauschlicher, Charles W., Jr.↗

Sampling Strategy and Curation Plan of "Hayabusa" Asteroid Sample Return Mission

On the 9th May 2003 JST, Japanese spacecraft MUSES-C was successfully launched from Uchinoura. The spacecraft was directly inserted to interplanetary trajectory and renamed as Hayabusa , or "Falcon" to be the world s first sample return spacecraft to a near Earth asteroid (NEA). The NEA (25143)Itokawa (formerly known as "1998SF36") is its mission target. Its orbital and physical characteristics were well observed; the size is (490 +/- 100)x (250 +/- 55)x(180 +/- 50) m with about 12-hour rotation period. It has a red-sloped S(IV)-type spectrum with strong 1- and 2-micron absorption bands, analogous to ordinary LL chondrites with space weathering effect. Assuming its bulk density, the surface gravity level of Itokawa is in the order of 10 micro-G with its escape velocity = approx. 20 cm/s.

Yano, H.↗

Toward Effective Shell Modeling of Wrinkled Thin-Film Membranes Exhibiting Stress Concentrations

Geometrically nonlinear shell finite element analysis has recently been applied to solar-sail membrane problems in order to model the out-of-plane deformations due to structural wrinkling. Whereas certain problems lend themselves to achieving converged nonlinear solutions that compare favorably with experimental observations, solutions to tensioned membranes exhibiting high stress concentrations have been difficult to obtain even with the best nonlinear finite element codes and advanced shell element technology. In this paper, two numerical studies are presented that pave the way to improving the modeling of this class of nonlinear problems. The studies address the issues of mesh refinement and stress-concentration alleviation, and the effects of these modeling strategies on the ability to attain converged nonlinear deformations due to wrinkling. The numerical studies demonstrate that excessive mesh refinement in the regions of stress concentration may be disadvantageous to achieving wrinkled equilibrium states, causing the nonlinear solution to lock in the membrane response mode, while totally discarding the very low-energy bending response that is necessary to cause wrinkling deformation patterns. An element-level, strain-energy density criterion is suggested for facilitating automated, adaptive mesh refinements specifically aimed at the modeling of thin-film membranes undergoing wrinkling deformations.

Tessler, Alexander↗

Small-Scale Gravity Waves in ER-2 MMS/MTP Wind and Temperature Measurements during CRYSTAL-FACE

Lower stratospheric wind and temperature measurements made from NASA's high-altitude ER-2 research aircraft during the CRYSTAL-FACE campaign in July 2002 were analyzed to retrieve information on small scale gravity waves (GWs) at the aircraft's flight level (typically approximately 20 km altitude). For a given flight segment, the S-transform (a Gaussian wavelet transform) was used to search for and identify small horizontal scale GW events, and to estimate their apparent horizontal wavelengths. The horizontal propagation directions of the events were determined using the Stokes parameter method combined with the cross S-transform analysis. The vertical temperature gradient was used to determine the vertical wavelengths of the events. GW momentum fluxes were calculated from the cross S-transform. Other wave parameters such as intrinsic frequencies were calculated using the GW dispersion relation. More than 100GW events were identified. They were generally high frequency waves with vertical wavelength of approximately 5 km and horizontal wavelength generally shorter than 20 km. Their intrinsic propagation directions were predominantly toward the east, whereas their ground-based propagation directions were primarily toward the west. Among the events, approximately 20% of them had very short horizontal wavelength, very high intrinsic frequency, and relatively small momentum fluxes, and thus they were likely trapped in the lower stratosphere. Using the estimated GW parameters and the background winds and stabilities from the NCAR/NCEP reanalysis data, we were able to trace the sources of the events using a simple reverse ray-tracing. More than 70% of the events were traced back to convective sources in the troposphere, and the sources were generally located upstream of the locations of the events observed at the aircraft level. Finally, a probability density function of the reversible cooling rate due to GWs was obtained in this study, which may be useful for cirrus cloud models.

Wang, L.↗

Computer Code for Nanostructure Simulation

Due to their small size, nanostructures can have stress and thermal gradients that are larger than any macroscopic analogue. These gradients can lead to specific regions that are susceptible to failure via processes such as plastic deformation by dislocation emission, chemical debonding, and interfacial alloying. A program has been developed that rigorously simulates and predicts optoelectronic properties of nanostructures of virtually any geometrical complexity and material composition. It can be used in simulations of energy level structure, wave functions, density of states of spatially configured phonon-coupled electrons, excitons in quantum dots, quantum rings, quantum ring complexes, and more. The code can be used to calculate stress distributions and thermal transport properties for a variety of nanostructures and interfaces, transport and scattering at nanoscale interfaces and surfaces under various stress states, and alloy compositional gradients. The code allows users to perform modeling of charge transport processes through quantum-dot (QD) arrays as functions of inter-dot distance, array order versus disorder, QD orientation, shape, size, and chemical composition for applications in photovoltaics and physical properties of QD-based biochemical sensors. The code can be used to study the hot exciton formation/relation dynamics in arrays of QDs of different shapes and sizes at different temperatures. It also can be used to understand the relation among the deposition parameters and inherent stresses, strain deformation, heat flow, and failure of nanostructures.

Filikhin, Igor↗

Generation of Requirements for Simulant Measurements

This TM presents a formal, logical explanation of the parameters selected for the figure of merit (FoM) algorithm. The FoM algorithm is used to evaluate lunar regolith simulant. The objectives, requirements, assumptions, and analysis behind the parameters are provided. A requirement is derived to verify and validate simulant performance versus lunar regolith from NASA s objectives for lunar simulants. This requirement leads to a specification that comparative measurements be taken the same way on the regolith and the simulant. In turn, this leads to a set of nine criteria with which to evaluate comparative measurements. Many of the potential measurements of interest are not defensible under these criteria. For example, many geotechnical properties of interest were not explicitly measured during Apollo and they can only be measured in situ on the Moon. A 2005 workshop identified 32 properties of major interest to users. Virtually all of the properties are tightly constrained, though not predictable, if just four parameters are controlled. Three parameters (composition, size, and shape) are recognized as being definable at the particle level. The fourth parameter (density) is a bulk property. In recent work, a fifth parameter (spectroscopy) has been identified, which will need to be added to future releases of the FoM.

Rickman, D. L.↗

Using CTX Image Features to Predict HiRISE-Equivalent Rock Density

Methods have been developed to quantitatively assess rock hazards at candidate landing sites with the aid of images from the HiRISE camera onboard NASA s Mars Reconnaissance Orbiter. HiRISE is able to resolve rocks as small as 1-m in diameter. Some sites of interest do not have adequate coverage with the highest resolution sensors and there is a need to infer relevant information (like site safety or underlying geomorphology). The proposed approach would make it possible to obtain rock density estimates at a level close to or equal to those obtained from high-resolution sensors where individual rocks are discernable.

Serrano, Navid↗

Mitigating Structural Defects in Droop-Minimizing InGaN/GaN Quantum Well Heterostructures

Modern commercial InGaN/GaN blue LEDs continue to suffer from efficiency droop, a reduction in efficiency with increasing drive current. External quantum efficiency (EQE) typically peaks at low drive currents (< 10 A cm 2 ) and drops monotonically at higher current densities, falling to <85% of the peak EQE at a drive current of 100 A cm 2 . Mitigating droop-related losses will yield tremendous gains in both luminous efficacy (lumens/W) and cost (lumens/$). Such improvements are critical for continued large-scale market penetration of LED technologies, particularly in high-power and high flux per unit area applications. However, device structures that reduce droop typically require higher indium content and are accompanied by a corresponding degradation in material quality which negates the droop improvement via enhanced Shockley-Read-Hall (SRH) recombination. In this work, we use advanced characterization techniques to identify and classify structural defects in InGaN/GaN quantum well (QW) heterostructures that share features with low-droop designs. Using aberration-corrected scanning transmission electron microscopy (C s -STEM), we find the presence of severe well width fluctuations (WWFs) in a number of low droop device architectures. However, the presence of WWFs does not correlate strongly with external quantum efficiency nor defect densities measured via deep level optical spectroscopy (DLOS). Hence, performance losses in the heterostructures of interest are likely dominated by nanoscale point or interfacial defects rather than large-scale extended defects.

36 MATERIALS SCIENCE↗

New View of the QCD Phase Diagram

Quarkyonic matter is confining but can have densities much larger than 3QCD. Its existence isargued in the large Nc limit of QCD and implies that there are at least three phases of QCD with greatly different bulk properties. These are a Confined Phase of hadrons, a Deconfined Phase ofquarks and gluons, and the Quarkyonic Phase. In the Quarkyonic Phase, the baryon density isaccounted for by a quasi-free gas of quarks, and the the antiquarks and gluons are confined intomesons, glueballs. Quarks near the Fermi surface also are treated as baryons. (In addition tothese phases, there is a color superconducting phase that has vastly different transport properties than the above, but with bulk properties, such as pressure and energy density, that are not greatlydifferent than that of Quarkyonic Matter.)

18-FDG↗

Fermi Surface Evolution Across Multiple Charge Density Wave Transitions in ErTe3

The Fermi surface (FS) of ErTe{sub 3} is investigated using angle-resolved photoemission spectroscopy (ARPES). Low temperature measurements reveal two incommensurate charge density wave (CDW) gaps created by perpendicular FS nesting vectors. A large {Delta}{sub 1} = 175 meV gap arising from a CDW with c* - q{sub CDW1} {approx} 0.70(0)c* is in good agreement with the expected value. A second, smaller {Delta}{sub 2} = 50 meV gap is due to a second CDW with a* - q{sub CDW2} {approx} 0.68(5)a*. The temperature dependence of the FS, the two gaps and possible interaction between the CDWs are examined.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗