Search NASA⌕ Search

SEARCH · Search NASA

Results for “PASSIVATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

A Passive Magnetoelastic Radiation Sensor

A passive gamma detection technology, consisting of a fielded sensor and a separate analysis system, is described. The sensor is a small cylinder, about 2.5 mm in diameter and 15 mm in length. It requires no onboard power sources or physical connections for power or data transfer, and retains its cumulative response to radiation. The sensor consists of an amorphous magnetoelastic wire held in a longitudinally-stressed state by a radiation-sensitive material. When the radiation-sensitive material is subjected to gamma radiation, it mechanically degrades, relaxing the stress on the wire and lowering the wire’s magnetic permeability. The changes in permeability are observed by switching the magnetic domains in the wire and measuring the reduction in the Faraday voltage as the stress is diminished. The analysis package is built around an excitation-detection coil set and can communicate wirelessly with the sensor through a metallic or nonmetallic barrier at distances up to about 25 mm. The sensor response is linear up to a dose of at least 7 kGy.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

All-Ceramic Passive Wireless Temperature Sensor Realized by Tin-Doped Indium Oxide (ITO) Electrodes for Harsh Environment Applications

In this work, an all-ceramic passive wireless inductor–capacitor (LC) resonator was presented for stable temperature sensing up to 1200 °C in air. Instead of using conventional metallic electrodes, the LC resonators are modeled and fabricated with thermally stable and highly electroconductive ceramic oxide. The LC resonator was modeled in ANSYS HFSS to operate in a low-frequency region (50 MHz) within 50 × 50 mm geometry using the actual material properties of the circuit elements. The LC resonator was composed of a parallel plate capacitor coupled with a planar inductor deposited on an Al2O3 substrate using screen-printing, and the ceramic pattern was sintered at 1250 °C for 4 h in an ambient atmosphere. The sensitivity (average change in resonant frequency with respect to temperature) from 200–1200 °C was ~170 kHz/°C. The temperature-dependent electrical conductivity of the tin-doped indium oxide (ITO, 10% SnO2 doping) on the quality factor showed an increase of Qf from 36 to 43 between 200 °C and 1200 °C. The proposed ITO electrodes displayed improved sensitivity and quality factor at elevated temperatures, proving them to be an excellent candidate for temperature sensing in harsh environments. The microstructural analysis of the co-sintered LC resonator was performed using a scanning electron microscope (SEM) which showed that there are no cross-sectional and topographical defects after several thermal treatments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Wireless Passive Ceramic Sensor for Far-Field Temperature Measurement at High Temperatures

A passive wireless high-temperature sensor for far-field applications was developed for stable temperature sensing up to 1000 °C. The goal is to leverage the properties of electroceramic materials, including adequate electrical conductivity, high-temperature resilience, and chemical stability in harsh environments. Initial sensors were fabricated using Ag for operation to 600 °C to achieve a baseline understanding of temperature sensing principles using patch antenna designs. Fabrication then followed with higher temperature sensors made from (In, Sn) O2 (ITO) for evaluation up to 1000 °C. A patch antenna was modeled in ANSYS HFSS to operate in a high-frequency region (2.5–3.5 GHz) within a 50 × 50 mm2 confined geometric area using characteristic material properties. The sensor was fabricated on Al2O3 using screen printing methods and then sintered at 700 °C for Ag and 1200 °C for ITO in an ambient atmosphere. Sensors were evaluated at 600 °C for Ag and 1000 °C for ITO and analyzed at set interrogating distances up to 0.75 m using ultra-wideband slot antennas to collect scattering parameters. The sensitivity (average change in resonant frequency with respect to temperature) from 50 to 1000 °C was between 22 and 62 kHz/°C which decreased as interrogating distances reached 0.75 m.

47 OTHER INSTRUMENTATION↗

Front/Back Poly-Si/SiO2 Passivated Contact Device with Voc > 720 mV

We report on front/back poly-Si/SiO2 passivated contact solar cells with iVoc > 735 mV and Voc > 720 mV. The devices were grown on n-Cz wafers using PECVD to deposit doped a-Si layers which were then annealed at 850 degrees C. Our best device has an efficiency of 21% which is limited by: (1) low current density from a large grid shadow loss and parasitic absorption in the front poly-Si:P layer; and (2) high series resistance from a high Al-poly-Si:P contact resistivity. We discuss the role of high temperature anneals throughout the process flow to preserve and improve the bulk lifetime of the n-Cz wafers.

14 SOLAR ENERGY↗

Discussion of the General Electric proposal to develop a computer program to select thermal coatings for passive temperature control of satellites

The General Electric Company, Missiles and Space Division, submitted/a proposal to NASA for the development of an IBM 7094 computer program which would select the exterior surface coatings for passively controlling spacecraft temperatures. G. E. claims that the "trial and error" procedures currently used can be accomplished more rationally and can therefore be programmed for a digital computer. In the ASME paper, 63-HT-41, which was presented at the ASME-AIChE Heat Transfer Conference at Boston in August, 1963, Costello, Harper, and Cline, described the procedures that have been used at G. E. to develop a coating selection program subject to the following restrictions: 1. Steady-state conditions prevail, 2. Heat transfer occurs by radiation only, 3. Temperatures are optimized at only one interior point in the spacecraft, an d 4. Only the solar absorptance of the external coatings is varied to optimize temperature. The emittance must remain constant at initially specified values. General Electric proposes to develop a generalized program in three steps: 1. The program would vary both solar absorptance and hemispherical emittance to obtain the optimum coating patterns; 2. Temperatures would be optimized at more than one interior point; and 3. The equations would be modified to account for both conduction and radiation heat transfer. In the development of the general program, the scope would be restricted to steady-state heat transfer. Since the thermal designs of most spacecraft are based primarily on nearly equilibrium conditions, the proposed program could have wide application. An obvious extension of the proposed program would be to account for transient temperatures.

IBM 7090 COMPUTER↗