Search NASA⌕ Search

SEARCH · Search NASA

Results for “Process sensitivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Photocatalytic degradation of pentachlorophenol in aqueous solution by visible light sensitive N-F-codoped TiO{sub 2} photocatalyst

Graphical abstract: Schematic representation for the visible light photocatalytic process of N and F codoped TiO{sub 2}. Highlights: ► Visible light sensitive N-F-codoped TiO{sub 2}. ► Photocatalytic degradation of pentachlorophenol. ► Effect of oxidants on photocatalytic degradation of pentachlorophenol. ► PMS is a more efficient oxidant for the photodegradation of PCP. - Abstract: In this present study, N-F-codoped titanium dioxide nanocatalyst (NFTO) has been synthesized by simple sol–gel assisted solvothermal method for the effective utilization of visible light in photocatalytic reactions. Structural characterization of the photocatalyst is analyzed by XRD, UV–vis diffuse reflectance spectra (DRS), SEM and TEM. Moreover the chemical statuses of NFTO are gathered by X-ray photoelectron spectroscopy (XPS). The results show that a high surface area with photoactive anatase phase crystalline is obtained. In addition, nitrogen and fluorine atoms are doped into TiO{sub 2} crystal lattice to extend the visible light absorption and higher photocatalytic activity. The photocatalytic degradation of pentachlorophenol in aqueous solution is examined under visible light irradiation, the addition of oxidants such as PMS, PDS and H{sub 2}O{sub 2} is analyzed in detail. The rate of photocatalytic degradation of pentachlorophenol is obtained in the following order: PMS > PDS > H{sub 2}O{sub 2}.

36 MATERIALS SCIENCE↗

Non-Equilibrium Processes, Stability, Design and Control of Pulsed Plasmas for Materials Processing

The energy and angle of impact of ions, interspersed with fluxes of neutral radicals, on the surface of wafers during plasma materials processing are critical parameters for the fabrication of microelectronic devices, nanostructure materials and biocompatible materials. This sensitivity extends to nearly all applications of plasmas to materials processing and surface modification. Low temperature plasmas for plasma materials processing have traditionally used continuously excited plasmas. However, pulsed plasma processing is an enabling technology for achieving finer resolution of microelectronics fabrication and for producing unique surface properties in a wide range of applications. This research project is addressing fundamental plasma physics issues in materials processing – the control of pulsed plasmas and the means for optimizing plasma produced reactant fluxes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Resonance self-shielding effects on Eigenvalue sensitivity

We present a quick and accurate way to compute the eigenvalue sensitivity coefficients in multigroup lattice cell calculations. We look at both the explicit and implicit sensitivities, the latter resulting from the resonance self-shielding process. A self-shielding model is presented, and we show how to obtain cross section sensitivities to a variation on a light isotope density. As an example, we look at how a perturbation on the hydrogen density affects the multigroup cross sections for resonant reactions such as U'capture and U'fission, in two uranium spheres with different enrichments. Explicit sensitivities are also computed, and we discuss the relative importance of the implicit sensitivities. (authors)

97 MATHEMATICS AND COMPUTING↗

Effects of mesh resolution on large eddy simulation of reacting flows in complex geometry combustors

The power of current parallel computers is becoming sufficient to apply large eddy simulation (LES) tools to reacting flows not only in academic configurations but also in real gas turbine chambers. The most limiting factor in performing LES of real systems is the mesh size, which directly controls the overall cost of the simulation, so that the effects of mesh resolution on LES results become a key issue. In the present work, an unstructured compressible LES solver is used to compute the reacting flow in a domain corresponding to a sector of a realistic helicopter chamber. Three grids ranging from 1.2 to 44 million elements are used for LES and results are compared in terms of mean and fluctuating fields as well as of pressure spectra. Results show that the mean temperature, reaction rate, and velocity fields are almost insensitive to the grid size. The RMS field of the resolved velocity is also reasonably independent of the mesh, while the RMS fields of temperature exhibit more sensitivity to the grid, as expected from the fact that most of the combustion process proceeds at small scales. The acoustic field exhibits a limited sensitivity to the mesh, suggesting that LES is adapted to the computation of combustion instabilities in complex systems. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Benchmarking of a treatment planning system for spot scanning proton therapy: Comparison and analysis of robustness to setup errors of photon IMRT and proton SFUD treatment plans of base of skull meningioma

Purpose: Base of skull meningioma can be treated with both intensity modulated radiation therapy (IMRT) and spot scanned proton therapy (PT). One of the main benefits of PT is better sparing of organs at risk, but due to the physical and dosimetric characteristics of protons, spot scanned PT can be more sensitive to the uncertainties encountered in the treatment process compared with photon treatment. Therefore, robustness analysis should be part of a comprehensive comparison between these two treatment methods in order to quantify and understand the sensitivity of the treatment techniques to uncertainties. The aim of this work was to benchmark a spot scanning treatment planning system for planning of base of skull meningioma and to compare the created plans and analyze their robustness to setup errors against the IMRT technique. Methods: Plans were produced for three base of skull meningioma cases: IMRT planned with a commercial TPS [Monaco (Elekta AB, Sweden)]; single field uniform dose (SFUD) spot scanning PT produced with an in-house TPS (PSI-plan); and SFUD spot scanning PT plan created with a commercial TPS [XiO (Elekta AB, Sweden)]. A tool for evaluating robustness to random setup errors was created and, for each plan, both a dosimetric evaluation and a robustness analysis to setup errors were performed. Results: It was possible to create clinically acceptable treatment plans for spot scanning proton therapy of meningioma with a commercially available TPS. However, since each treatment planning system uses different methods, this comparison showed different dosimetric results as well as different sensitivities to setup uncertainties. The results confirmed the necessity of an analysis tool for assessing plan robustness to provide a fair comparison of photon and proton plans. Conclusions: Robustness analysis is a critical part of plan evaluation when comparing IMRT plans with spot scanned proton therapy plans.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Herbaceous Feedstock 2018 State of Technology Report

The U.S. Department of Energy (DOE) promotes the production of advanced liquid transportation fuels from lignocellulosic biomass by funding fundamental and applied research that advances the state of technology (SOT). As part of its involvement with this mission, Idaho National Laboratory (INL) completes an annual SOT report for biomass feedstock logistics. This report summarizes supply system impacts of Bioenergy Technologies Office (BETO)-funded research and development efforts at INL and elsewhere (such as the High-Tonnage Feedstock Logistics projects (Webb et al. 2013a, Webb et al. 2013b, Webb et al. 2013c, Webb and Sokhansanj 2014, Sokhansanj et al. 2014) that lead to improvements in feedstock supply systems. These include improvements to and observed performance of innovative harvest and collection methods, storage technologies, transportation and handling approaches, and advanced preprocessing technologies. Biomass quality and variability, and the interface between feedstock quality and conversion performance are key drivers in addition to delivered feedstock cost. In this report, we estimate the benefits of R&D improvements to individual supply system unit operations, and present the status of feedstock logistics technology development for converting biomass into biofuels. These analyses are supported by experimental data where possible, and help to align the SOT relative to the cost goals defined in the Multi-Year Program Plan. The 2018 Herbaceous SOT aligned feedstock logistic design with current biorefinery’s design capacity utilized by biochemical conversion platform. Currently biochemical conversion platform utilizes a 725,000 dry ton/year biorefiney design for the techno economic analysis. Hence, feedstock delivered cost in the 2018 Herbaceous SOT is calculated based on biorefinery’s 725,000 dry ton design capacity instead of 800, 000 dry ton capacity utilized in the 2017 Herbaceous SOT. Biomass availabilities in this SOT were updated to year 2018 data from the 2016 Billion-Ton Report (BT16) (DOE 2016a), with the exception of switchgrass, for which the 2018 Herbaceous SOT utilized the 2019 switchgrass availability data from BT16. The BT16 report (DOE 2016a) does not project switchgrass availability in 2018; the soonest switchgrass is available in the BT16 report is 2019. Therefore, availability of switchgrass for this analysis was that projected for 2019. The 2018 Herbaceous SOT incorporates same technologies utilized in the 2017 Herbaceous SOT. However, a sensitivity analysis is performed to understand the impact of variation of process parameters on those technologies on feedstock logistic cost. New R&D data that shows the variations of process parameters affecting process performance is incorporated in the 2018 SOT to measure the variations in delivered feedstock cost. The 2018 Herbaceous SOT has also provided projected delivered feedstock of 2022 design case based on near term technical target under BETO funded R&D project. Finally, updated biorefinery size of 725,000 dry ton/year was incorporated within least-cost formulation model to select optimal siting and depot scales during optimization of the least cost blend. This modification to the optimization algorithm allows the trade-off between the cost of increased supply radius and the savings from selecting biomass from higher producing counties to be assessed. Such optimization has also showed the economic benefit of decentralized depots in comparison to centralized preprocessing co-located with the biorefinery by decoupling the biorefinery and feedstock locations. The 2018 Herbaceous SOT report documents the current modeled cost of a herbaceous feedstock supply system (from harvest to the pretreatment reactor throat, including grower payment) for hydrocarbon fuel production via biochemical conversion, based on equipment and processes now available or potentially available in the near term. The modeled cost also considers both the required quality and the availability of the biomass resources. The 2018 Herbaceous SOT predicts a modeled delivered feedstock cost of $83.67/dry ton (2016$); this is a $0.23/dry ton (2016$) decrease from the 2017 Herbaceous SOT. The modification of biorefinery’s designed capacity and increased projected biomass availability in the same supply shed contributed to this modeled cost reduction. The least-cost formulation model to optimally site and scale local distributed preprocessing depots also contributed to the cost reduction by considering county-level grower payment and distance from the biorefinery as variables in the optimization algorithm. Sensitivity analysis on various process parameters that affect delivered feedstock cost in the 2018 Herbaceous SOT shows that the delivered cost could varies from $80.45-$88.83/dry ton. The top factors that causes such variations are: effective baling rate, bale density, hammer mill throughput, interest rate and storage dry matter loss.

09 BIOMASS FUELS↗

Structural damage response of lanthanum and yttrium aluminate crystals to nuclear collisions and electronic excitation: Threshold assessment of irradiation damage

A comparative analysis is performed on the structural damage response and associated mechanisms in lanthanum aluminate and yttrium aluminate crystals under various irradiation conditions by a combination of experimental and theoretical approaches. Under low-energy Au+ irradiation, the damage accumulation curve shows a higher damage rate for LaAlO 3 crystals than YAlO 3 crystals. The relatively low irradiation tolerance of LaAlO 3 to the action of nuclear collisions is ascribed to the large amorphization cross-section and effective cross-section for defect-stimulated amorphization. Under swift Ar 12+ , Ni 19+ and Kr 17+ irradiation with different ion energies and velocities, the formed highly-disordered/amorphous latent tracks with different morphologies in pristine and predamaged crystals are discussed, and the corresponding electronic energy loss and lattice temperature thresholds are quantitatively determined. Compared to YAlO 3 , LaAlO 3 exhibits lower sensitivity and higher damage tolerance to the electronic energy loss process, attributing to its relatively high recrystallization efficiency during the rapid quenching process. Furthermore, the introduction of lattice defects into LaAlO 3 and YAlO 3 crystals considerably enhances the sensitivity and intensity of thermal spike response to the electronic energy loss, and the induced effective modification of track morphologies demonstrates the synergistic effect between the electronic energy loss and pre-existing defects created by nuclear collisions. In this case, even under the action of electronic energy loss below the threshold, the lattice temperature in the nuclear-collision damaged crystalline system could still meet the criterion for track production. The irradiation energy deposited to atoms and induced lattice temperature evolution discussed in this work provide a deeper insight into the complex processes involved in irradiation-induced latent track behaviors.

36 MATERIALS SCIENCE↗

Sensitivity of aerosol properties to new particle formation mechanism and to primary emissions in a continental-scale chemical transport model

Four theoretical formulations of new particle formation (NPF) and one empirical formulation are used to examine the sensitivity of observable aerosol properties to NPF formulation and to properties of emitted particles in a continental-scale model for the United States over a 1-month simulation (July 2004). For each formulation the dominant source of Aitken mode particles is NPF with only a minor contribution from primary emissions, whereas for the accumulation mode both emissions and transfer of particles from the Aitken mode are important. The dominant sink of Aitken mode number is coagulation, whereas the dominant sink of accumulation mode number is wet deposition (including cloud processing), with a minor contribution from coagulation. The aerosol mass concentration, which is primarily in the accumulation mode, is relatively insensitive to NPF formulation despite order-of-magnitude differences in the Aitken mode number concentration among the different parameterizations. The dominant sensitivity of accumulation mode number concentration is to the number of emitted particles (for constant mass emission rate). Comparison of modeled aerosol properties with aircraft measurements shows, as expected, better agreement in aerosol mass concentration than in aerosol number concentration for all NPF formulations considered. These comparisons yield instances of rather accurate simulations in the planetary boundary layer, with poor model performance in the free troposphere attributed mainly to lack of representation of biomass burning and/or to long-range transport of particles from outside the model domain. Agreement between model results and measurements is improved by using smaller grid cells (12 km versus 60 km).

09 BIOMASS FUELS↗

Picoflow Liquid Chromatography–Mass Spectrometry for Ultrasensitive Bottom-Up Proteomics Using 2-μm-i.d. Open Tubular Columns

In many areas of applications key objectives of chemical separations and analysis are to minimize the sample quantity while maximizing the chemical information obtained. Increasing measurement sensitivity is especially critical for proteomics research, especially when processing trace samples and where multiple measurements are desired. A rich collection of technologies has been developed, but the resulting sensitivity remains insufficient for achieving in-depth coverage of proteomic samples as small as single cells. In this paper, we combine picoliter-scale liquid chromatography (picoLC) with mass spectrometry (MS) to address this issue. The picoLC employs 2-µm-i.d. open tubular column to reduce the sample input needed to greatly increase the sensitivity achieved using electrospray ionization (ESI) with MS. With this picoLC-MS system, we show that we can identify ~1000 proteins reliably using only 30 pg of tryptic peptides, representing a 10–100-fold sensitivity improvement compared with the state-of-the-art liquid chromatography (LC) or capillary electrophoresis (CE)-MS methods. PicoLC-MS extends the limit of separation science and is expected to be a powerful tool for single cell proteomics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Resolution Three-Dimensional Sculpting of Two-Dimensional Graphene Oxide by E-Beam Direct Write

On demand switchable additive/subtractive patterning of 2D nanomaterials is an essential capability for developing new concepts of functional nanomaterials and their device realizations. Traditionally, this is performed via a multi-step process using photoresist coating and patterning by conventional photo or electron beam lithography, which is followed by bulk dry/wet etch or deposition. This limits the range of functionalities and structural topologies that can be achieved, as well as increases the complexity, cost, and possibility of contamination which are significant barriers to device fabrication from highly sensitive 2D materials. Focused electron beam induced processing (FEBIP) enables a material chemistry/site-specific, high-resolution multi-mode atomic scale processing and provides unprecedented opportunities for direct-write, single-step surface patterning of 2D nanomaterials with an in-situ imaging capability. It allows for realizing a rapid multi-scale/multi-mode approach, ranging from an atomic scale manipulation (e.g., via targeted defect introduction as an active site) to a large-area surface modification on nano and micro scales, including patterned doping and material removal/deposition with 2D (in-plane)/3D (out-of-plane) control. In this work, we report on a new capability of FEBIP for nanoscale patterning of graphene oxide via removal of oxygenated carbon moieties with no use of reactive gas required for etching complemented by carbon atom deposition using focused electron beam. The mechanism of experimentally observed phenomena is explored using the density functional theory (DFT) calculations, revealing that interactions of e-beam liberated reactive oxygen radicals with carbon atoms on graphene basal plane lead to creation of atomic vacancies in the material. The reaction by-products are volatile carbon di-oxides, which are dissociated and volatilized from the graphene oxide surface functional groups by interactions with an energetic focused electron beam. Along with selective “subtractive” patterning of graphene oxide, the same electron beam with increased irradiation doses can deposit out-of-plane 3D carbon nanostructures on top of or around the 2D etched pattern, thus forming a hybrid 2D/3D nanocomposite with feature control down to a few nanometers. Furthermore, this in-operando dual nanofabrication capability of FEBIP is unmatched by any other nanopatterning techniques and opens a new design window for forming 2D/3D complex nanostructures and functional nanodevices.

36 MATERIALS SCIENCE↗

First inverse kinematics measurement of resonances in Be 7 ( α , γ ) C 11 relevant to neutrino-driven wind nucleosynthesis using DRAGON

A possible mechanism to explain the origin of the light $\textit{p}$ nuclei in the Galaxy is the nucleosynthesis in the proton-rich neutrino-driven wind ejecta of core-collapse supernovas via the $\textit{νp}$ process. However, this production scenario is very sensitive to the underlying supernova dynamics and the nuclear physics input. As far as the nuclear uncertainties are concerned, the breakout from the $\textit{pp}$ chains via the 7 Be(α,γ) 11 C reaction has been identified as an important link which can influence the nuclear flow and, therefore, the efficiency of the $\textit{νp}$ process. However, its reaction rate is poorly known over the relevant temperature range, $\textit{T}$ = 1.5–3 GK. We report on the first direct measurement of two resonances of the 7 Be(α,γ) 11 C reaction with previously unknown strengths using an intense radioactive 7 Be beam from the Isotope Separator and Accelerator (ISAC-I) Center facility and the DRAGON recoil separator in inverse kinematics. In this work, we have decreased the 7 Be(α,γ) 11 C reaction rate uncertainty to ≈9.4–10.7% over the relevant temperature region.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Effect of Pre- and Post-Coat Processing on the Fatigue Life of Coated Disk Alloys

Increasing temperatures in aero gas turbines is resulting in oxidation and hot corrosion attack of turbine disks. Since disks are sensitive to low cycle fatigue (LCF), any environmental attack, and especially hot corrosion pitting, can seriously degrade the life of the disk. Application of metallic coatings is one means of protecting disk alloys from this environmental attack. However, since LCF is sensitive to surface conditions, pre- and post-coat processing can have a significant effect on the LCF life of coated bars. Various pre-and post-coating conditions were examined with a Ni-45wt. Cr coating applied by High-power impulse magnetron sputtering (HiPiMS) to a Ni-based disk alloy. Initial pre-coat surface conditions examined a grit blasted surface. Later pre-coat surface treatments involved wet blasting, two shot peening levels (8N-200 and 16N-200) and a highly polished surface. Post-coat treatments involved two shot peening levels (4N-100 and 16N-200) and a post-coat diffusion anneal in high purity Ar or a low PO2 environment to encourage chromia scale formation. Half of the coated and uncoated bars were LCF tested at 760C without further environmental exposure to evaluate the pre- and post-coat treatments. The second half of samples were either oxidized for 500 hours at 760C in air, hot corroded for 50 hours at 760C in air using a Na2SO4-MgSO4 salt, or subjected to both exposures. Results of the LCF testing and post-test characterization of the various coatings will be presented and future research directions discussed.

LCF Life↗

Feature extraction for structural dynamics model validation

This study focuses on defining and comparing response features that can be used for structural dynamics model validation studies. Features extracted from dynamic responses obtained analytically or experimentally, such as basic signal statistics, frequency spectra, and estimated time-series models, can be used to compare characteristics of structural system dynamics. By comparing those response features extracted from experimental data and numerical outputs, validation and uncertainty quantification of numerical model containing uncertain parameters can be realized. In this study, the applicability of some response features to model validation is first discussed using measured data from a simple test-bed structure and the associated numerical simulations of these experiments. issues that must be considered were sensitivity, dimensionality, type of response, and presence or absence of measurement noise in the response. Furthermore, we illustrate a comparison method of multivariate feature vectors for statistical model validation. Results show that the outlier detection technique using the Mahalanobis distance metric can be used as an effective and quantifiable technique for selecting appropriate model parameters. However, in this process, one must not only consider the sensitivity of the features being used, but also correlation of the parameters being compared.

42 ENGINEERING↗

M-H loop tracer based on digital signal processing for low frequency characterization of extremely thin magnetic wires

A high-sensitivity ac hysteresis loop tracer has been developed to measure the low frequency hysteresis loop of soft magnetic materials. It has been applied successfully to characterize straight pieces of amorphous glass-covered microwires with metallic nucleus down to 1.5 {mu}m thick. Based on the electromagnetic induction law, the proposed design is extremely simple and exploits the capabilities of commercially available data acquisition cards together with digital signal processing in order to achieve high-sensitivity without the need of expensive analog equipment.

36 MATERIALS SCIENCE↗

Sensitivity analysis of a parameterization of coagulation in an aqueous transport model

A three-dimensional aqueous transport model, ALGE, was developed at the Savannah River National Laboratory (SRNL) as a tool for emergency response. Recently, coagulation and break-up of sediment and particulate (contaminant adhered to sediment) matter has been added as a new model capability, representing both processes as functions of salinity and turbulence. A sensitivity analysis was performed by comparing time series of sediment and particulate concentrations at various locations when the model’s parameters (particle size and density) are altered. The results show significant differences between experiments in both freshwater and saltwater systems parameters vary (P-values < 0.05). From this sensitivity study, we have concluded the importance of incorporating both salinity and turbulent effects, as they have a large role in the physical process of coagulation and breakup of sediment. By accounting for these physical processes, we have made the ALGE model a more robust tool for emergency response.

Aqueous fate and transport↗

Synthesis of an aqueous, air-stable, superconducting 1T'-WS 2 monolayer

Liquid-phase chemical exfoliation can achieve industry-scale production of two-dimensional (2D) materials for a wide range of applications. However, many 2D materials with potential applications in quantum technologies often fail to leave the laboratory setting because of their air sensitivity and depreciation of physical performance after chemical processing. We report a simple chemical exfoliation method to create a stable, aqueous, surfactant-free, superconducting ink containing phase-pure 1T'-WS 2 monolayers that are isostructural to the air-sensitive topological insulator 1T'-WTe 2 . The printed film is metallic at room temperature and superconducting below 7.3 kelvin, shows strong anisotropic unconventional superconducting behavior with an in-plane and out-of-plane upper critical magnetic field of 30.1 and 5.3 tesla, and is stable at ambient conditions for at least 30 days. Our results show that chemical processing can make nontrivial 2D materials that were formerly only studied in laboratories commercially accessible.

36 MATERIALS SCIENCE↗

Functionalization of polymers using an atmospheric plasma jet in a fluidized bed reactor and the impact on SLM-processes

In order to improve thermoplastics (e.g. Polyamide, Polypropylene and Polyethylene) for Selective Laser Beam Melting (SLM) processes a new approach to functionalize temperature sensitive polymer powders in a large scale is investigated. This is achieved by combining an atmospheric pressure plasma jet and a fluidized bed reactor. Using pressurized air as the plasma gas, radicals like OH* are created. The functionalization leads to an increase of the hydrophilicity of the treated polymer powder without changing the bulk properties. Using the polymers in a SLM process to build single layers of melted material leads to an improvement of the melted layers.

36 MATERIALS SCIENCE↗

A Novel Additive Manufacturing Process Metric for Predicting Spatter-related Porosity in Laser Powder Bed Fusion

Components fabricated using the powder bed fusion laser beam metallic (PBF) additive manufacturing (AM) process comprise a multitude of sequential weld passes. Porosity defects resulting from weld pass inconsistencies are a concern for PBF materials and have a strong adverse effect on the mechanical properties. In an effort to understand and avoid spatter induced porosity, this work aims to provide a novel computational technique that can be used to quantify and predict the sequence-sensitive impact of spatter upon the PBF process stability and consequential porosity in as-printed material. A novel spatter impact AM model-based process metric (AM-PM) is introduced to model and quantify the impact that spatter has on the PBF process. The occurrence of spatter induced porosity is studied using thermal rise, lack of fusion, and spatter impact AM-PMs synchronized with porosity measured by high-resolution X-ray computed tomography. Six cylindrical specimens were designed to compare the AM-PM correlations with porosity across two different laser powers and three hatch scanning strategies. A point field based computational approach is shown to be effective for testing the influence of the different AM-PMs and interrogating the physical process conditions underlying the porosity formation. Further, characterization using optical metallography and scanning electron microscopy indicated that both keyhole and lack of fusion porosity correlated with the spatter impact AM-PM, which can be exploited to predict and control spatter related porosity by the hatch strategy. Efforts to predict porosity composition within PBF material should incorporate the PBF process disturbances that can result from spatter. The spatter impact AM-PM can be readily incorporated into the development of defect prediction models at the part scale.

Additive Manufacturing↗