Search NASA⌕ Search

SEARCH · Search NASA

Results for “flow improvers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Exact and approximate gas dynamics using the tangent gas

For the determination of aerodynamic characteristics such as lift, drag, and moment coefficients, it is crucial to compute the properties of steady flow past an airfoil. This investigation provides a set of flow dependent grid systems and initial flowfield guesses which substantially improve convergence rates when applied to the Euler equations for flows past an airfoil. The basic equations are examined, taking into account nonlinear equations which are difficult to solve. A good approximation to these equations under certain conditions can be obtained by introducing the so-called 'tangent gas approximation' considered by Woods (1961), in which the isentropic relation between rho and p is replaced by a tangent to a curve. Attention is given to the solution procedure, the analysis (direct) problem, and a comparison of the tangent gas solution with the converged Euler solution.

Daripa, P. K.↗

Oxygen extraction from lunar materials - An experimental test of an ilmenite reduction process

The reaction of ilmenite with hydrogen to produce water has been studied experimentally in order to evaluate the effectiveness of using a cold trap to improve yields in a continuous flow process. Yields were enhanced, but not to the degree observed in batch processing systems. The terrestrial simulant used in these studies contained traces of iron sulfide, which released H2S during processing with a deleterious effect on several components of the test system. More sophisticated testing should be undertaken to obtain kinetic data and attention given to the removal of sulfides in the pre-process beneficiation.

Williams, R. J.↗

NASA small civil airplane research

NASA-Langley's ongoing research programs on behalf of performance, safety, and utility enhancements for small civil aircraft have over the last decade introduced important advancements in natural laminar flow inducement and stall/spin recovery and prevention. The achievability and maintainability of natural laminar flow has led to performance improvements of as much as 25 percent. Recent research has improved predictive techniques for aircraft stall/spin characteristics, and also led to the development of a wing leading edge design for enhanced spin resistance.

Stough, H. Paul, III↗

Wake model for helicopter rotors in high speed flight

Two alternative approaches are developed to calculate blade-vortex interaction airloads on helicopter rotors: second order lifting-line theory, and a lifting surface theory correction. The common approach of using a larger vortex core radius to account for lifting-surface effects is quantified. The second order lifting-line theory also improves the modeling of yawed flow and swept tips. Calculated results are compared with wind tunnel measurements of lateral flapping, and with flight test measurements of blade section lift on SA349/2 and H-34 helicopter rotors. The tip vortex core radius required for good correlation with the flight test data is about 20 percent chord, which is within the range of measured viscous core sizes for helicopter rotors.

Johnson, Wayne R.↗

Additional development of the XTRAN3S computer program

Additional developments and enhancements to the XTRAN3S computer program, a code for calculation of steady and unsteady aerodynamics, and associated aeroelastic solutions, for 3-D wings in the transonic flow regime are described. Algorithm improvements for the XTRAN3S program were provided including an implicit finite difference scheme to enhance the allowable time step and vectorization for improved computational efficiency. The code was modified to treat configurations with a fuselage, multiple stores/nacelles/pylons, and winglets. Computer program changes (updates) for error corrections and updates for version control are provided.

Borland, C. J.↗

Turbulence energy redistributive model

A study is made to improve the predictions of turbulent flows through modifications of the pressure-strain correlation of the Reynolds stress equations. The mean-strain term of the pressure-strain correlation is formulated by incorporating the tensor with the Reynolds stresses that account for a non-isotropic turbulence effect in the flows which are accompanied by a turbulent separating flow. This model is compared with other existing models and results are verified with existing experimental results for turbulent shear flows.

Amano, R. S.↗

Hypersonic nonequilibrium viscous solutions over slender bodies

An extension is undertaken of a previous numerical study in order to improve current understanding of nonequilibrium flow effects over slender bodies. Upon extension of the parametric study to encompass smaller nose radii, the downstream influence of equilibrium nonequilibrium flow is found to be much smaller than for the larger nose radii. A comparison of individual stagnation nonequilibrium heating rates demonstrates that a relative comparison of the ratios was not indicative of the actual heating reduction.

Zoby, E. V.↗

New addition curing polyimides

In an attempt to improve the thermal-oxidative stability (TOS) of PMR-type polymers, the use of 1,4-phenylenebis (phenylmaleic anhydride) PPMA, was evaluated. Two series of nadic end-capped addition curing polyimides were prepared by imidizing PPMA with either 4,4'-methylene dianiline or p-phenylenediamine. The first resulted in improved solubility and increased resin flow while the latter yielded a compression molded neat resin sample with a T(sub g) of 408 C, close to 70 C higher than PME-15. The performance of these materials in long term weight loss studies was below that of PMR-15, independent of post-cure conditions. These results can be rationalized in terms of the thermal lability of the pendant phenyl groups and the incomplete imidization of the sterically congested PPMA. The preparation of model compounds as well as future research directions are discussed.

Frimer, Aryeh A.↗

MAG3D and its application to internal flowfield analysis

MAG3D (multiblock adaptive grid, 3D) is a 3D solution-adaptive grid generation code which redistributes grid points to improve the accuracy of a flow solution without increasing the number of grid points. The code is applicable to structured grids with a multiblock topology. It is independent of the original grid generator and the flow solver. The code uses the coordinates of an initial grid and the flow solution interpolated onto the new grid. MAG3D uses a numerical mapping and potential theory to modify the grid distribution based on properties of the flow solution on the initial grid. The adaptation technique is discussed, and the capability of MAG3D is demonstrated with several internal flow examples. Advantages of using solution-adaptive grids are also shown by comparing flow solutions on adaptive grids with those on initial grids.

Lee, K. D.↗

Stiffnesses by (TtN) ensemble molecular dynamics

Calculation of elastic constants requires initializing a lattice of atoms, an h matrix defining the computational cell boundaries, and the parameters defining the interatomic potentials, then numerically integrating the equations of motion for the atoms and the computational cell boundaries, calculating strains and stresses at each timestep, and updating at each timestep the average quantities required for calculation of fluctuations. Enforcements of the DYNAMO FORTRAN code included addition of documentation, improved memory management and data flow, and enabling use of several interatomic potentials. Documentation included headers for each subroutine, which document the parameters input to the routine, algorithms employed, and output.

Tibbits, Patrick↗

Direct numerical simulation of turbulent H2-O2 combustion using reduced chemistry

Results of direct numerical simulations of hydrogen-oxygen combustion using a partial-equilibrium chemistry scheme in constant density, decaying, isotropic turbulence are reported. The simulations qualitatively reproduce many features of experimental results, such as superequilibrium radical species mole fractions, with temperature and major species mole fractions closer to chemical equilibrium. It was also observed that the peak reaction rates occur in narrow zones where the stoichiometric surface intersects regions of high scalar dissipation, as might be expected for combustion conditions close to chemical equilibrium. Another finding was that high OH mole fraction correspond more closely to the stoichiometric surface than to areas of high reaction rate for conditions of the simulations. Simulation results were compared to predictions of the Conditional Moment Closure model. This model was found to give good results for all quantities of interest when the conditionally averaged scalar dissipation was used in the prediction. When the nonconditioned average dissipation was used, the predictions compared well to the simulations for most of the species and temperature, but not for the reaction rate. The comparison would be expected to improve for higher Reynolds number flows, however.

Montgomery, Christopher J.↗

Three-dimensional Navier-Stokes calculations using solution-adapted grids

A three-dimensional solution-adaptive grid generation technique is presented. The adaptation technique redistributes grid points to improve the accuracy of a flow solution without increasing the number of grid points. It is applicable to structured grids with a multiblock topology. The method uses a numerical mapping and potential theory to modify the initial grid distribution based on the properties of the flow solution on the initial grid. The technique is demonstrated with two examples - a transonic finite wing and a supersonic blunt fin. The advantages are shown by comparing flow solutions on the adapted grids with those on the initial grids.

Henderson, T. L.↗

A Visualization Study of Secondary Flows in Cascades

Flow-visualization techniques are employed to ascertain the streamline patterns of the nonpotential secondary flows in the boundary layers of cascades, and thereby to provide a basis for more extended analyses in turbomachines. The three-dimensional deflection of the end-wall boundary layer results in the formation of a vortex within each cascade passage. The size and tightness of the vortex generated depend upon the main-flow turning in the cascade passage. Once formed, a vortex resists turning in subsequent blade rows, with consequent unfavorable angles of attack and possible flow disturbances on the pressure surfaces of subsequent blade rows when the vortices impinge on these surfaces. Two major tip-clearance effects are observed, the formation of a tip-clearance vortex and the scraping effect of a blade with relative motion past the wall boundary layer. The flow patterns indicate methods for improving the blade tip-loading characteristics of compressors and of low- and high-speed turbulence.

Herzig, Howard Z↗

Rapid distortion analysis and direct simulation of compressible homogeneous turbulence at finite Mach number

The effect of rapid mean compression on compressible turbulence at a range of turbulent Mach numbers is investigated. Rapid distortion theory (RDT) and direct numerical simulation results for the case of axial (one-dimensional) compression are used to illustrate the existence of two distinct rapid compression regimes. These regimes are set by the relationships between the timescales of the mean distortion, the turbulence, and the speed of sound. A general RDT formulation is developed and is proposed as a means of improving turbulence models for compressible flows.

Cambon, C.↗

Use of Blade Lean in Turbomachinery Redesign

Blade lean is used to improve the uniformity of exit flow distributions from turbomachinery blading. In turbines, it has been used to control secondary flows by tailoring blade turning to reduce flow overturning and underturning and to create more uniform loss distributions from hub to shroud. In the present study, the Pump Consortium centrifugal impeller has been redesigned using blade lean. The flow at the exit of the baseline impeller had large blade-to-blade variations, creating a highly unsteady flow for the downstream diffuser. Blade lean is used to redesign the flow to move the high loss fluid from the suction side to the hub, significantly reducing blade-toblade variations at the exit.

Moore, John↗

Support of gas flowmeter upgrade

A project history review, literature review, and vendor search were conducted to identify a flowmeter that would improve the accuracy of gaseous flow measurements in the White Sands Test Facility (WSTF) Calibration Laboratory and the Hydrogen High Flow Facility. Both facilities currently use sonic flow nozzles to measure flowrates. The flow nozzle pressure drops combined with corresponding pressure and temperature measurements have been estimated to produce uncertainties in flowrate measurements of 2 to 5 percent. This study investigated the state of flowmeter technology to make recommendations that would reduce those uncertainties. Most flowmeters measure velocity and volume, therefore mass flow measurement must be calculated based on additional pressures and temperature measurement which contribute to the error. The two exceptions are thermal dispersion meters and Coriolis mass flowmeters. The thermal dispersion meters are accurate to 1 to 5 percent. The Coriolis meters are significantly more accurate, at least for liquids. For gases, there is evidence they may be accurate to within 0.5 percent or better of the flowrate, but there may be limitations due to inappropriate velocity, pressure, Mach number and vibration disturbances. In this report, a comparison of flowmeters is presented. Candidate Coriolis meters and a methodology to qualify the meter with tests both at WSTF and Southwest Research Institute are recommended and outlined.

Waugaman, Dennis↗

Rapid Distortion Analysis and Direct Simulation of Compressible Homogeneous Turbulence at Finite Mach Number

The effect of rapid mean compression on compressible turbulence at a range of turbulent Mach numbers is investigated. Rapid dist'ortion theory (RDT) and direct numerical simulation results for the case of axial (one-dimensional) compression are used to illustrate the existence of two distinct rapid compression regimes. These regimes - the nearly solenoidal and the 'pressure-released' - are defined by a single parameter involving the timescales of the mean distortion, the turbulence, and the speed of sound. A general RDT formulation is developed and is proposed as a means of improving turbulence models for compressible flows. In contrast to the well-documented observation that 'compressibility' (measured, for example, by the turbulent Mach number) is often associated with a decrease in the growth rate of turbulent kinetic energy, we find that under rapid distortion compressibility can produce an amplification of the kinetic energy growth rate. We also find that as the compressibility increases, the magnitude of the pressure-dilation correlation increases, in absolute terms, but its relative importance decreases compared to the magnitude of the kinetic energy production.

Cambon, C.↗

Seasonal Cycles of Meridional Overturning and Heat Transport of the Indian Ocean

A general circulation model of the Indian Ocean is fitted to monthly averaged climatological temperatures, salinities, and surface fluxes using the adjoint method. Interannual variability is minimized by penalizing the temporal drift from one seasonal cycle to another during a two-year integration. The resultant meridional overturning and heat transport display large seasonal variations, with maximum amplitudes of 18 and 22 (x 10(exp 6) cubic m/s) for the overturning and 1.8 and 1.4 (x 10(exp 15) W) for heat transport near 10 S and 10 N, respectively. A dynamical decomposition of the overturning and heat transport shows that the time-varying Ekman How plus its barotropic compensation can explain a large part of the seasonal variations in overturning and heat transport. The maximum variations at 10 deg N and 10 deg S are associated with monsoon reversal over the northern Indian Ocean and changes of the easterlies over the southern Indian Ocean. An external mode with variable topography has a moderate contribution where the Somali Current and the corresponding gyre reverse direction seasonally. Contribution front vertical shear (thermal wind and ageostrophic shear) is dominant near the southern boundary and large near the Somali Current latitudes. The dominant balance in the zonally integrated heat budget is between heat storage change and heat transport convergence except south of 15 S. Optimization with seasonal forcings improves estimates of sea surface temperatures, but the annual average overturning and heat transport are very similar to previous results with annual mean forcings. The annual average heat transport consists of roughly equal contributions from time-mean and time-varying fields of meridional velocities and temperatures in the northern Indian Ocean. indicating a significant rectification to the heat transport due to the time-varying fields. The time-mean and time-varying contributions are primarily due to the overturning and horizontal gyre, respectively. Inclusion of TOPEX data enhances the seasonal cycles of the estimated overturning and heat transport in the central Indian Ocean significantly and improves the estimated equatorial zonal flows but leads 10 unrealistic estimates of the velocity structure near the Indonesian Throughflow region, most likely owing to the deficiencies in the lateral boundary conditions.

Lee, Tong↗