Search NASA⌕ Search

SEARCH · Search NASA

Results for “load analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Study leading to the refinement of the SRB structural analysis program

The constructed SRB math model was used for the analysis of the 85/32/5(VV/VH/theta) cavity collapse load condition for the aft end of the SRB structure. Linear, nonlinear collapse and bifurcation buckling analyses were performed. The linear and bifurcation buckling analyses showed that structural integrity and positive margins of safety are maintained for the applied maximum load case using a design factor of 1.25. The nonlinear collapse analysis predicts stresses in the skirt above the yield for a load factor of 1.0. Applying the 1.25 design factor gives a negative margin of safety against the material ultimate. The predicted collapse occurs at a load factor higher than 1.25.

Jones, W. E.↗
NASA NTRS2010

Wind Tunnel Investigation of Ground Wind Loads for Ares Launch Vehicle

A three year program was conducted at the NASA Langley Research Center (LaRC) Aeroelasticity Branch (AB) and Transonic Dynamics Tunnel (TDT) with the primary objective to acquire scaled steady and dynamic ground-wind loads (GWL) wind-tunnel data for rollout, on-pad stay, and on-pad launch configurations for the Ares I-X Flight Test Vehicle (FTV). The experimental effort was conducted to obtain an understanding of the coupling of aerodynamic and structural characteristics that can result in large sustained wind-induced oscillations (WIO) on such a tall and slender launch vehicle and to generate a unique database for development and evaluation of analytical methods for predicting steady and dynamic GWL, especially those caused by vortex shedding, and resulting in significant WIO. This paper summarizes the wind-tunnel test program that employed two dynamically-aeroelastically scaled GWL models based on the Ares I-X Flight Test Vehicle. The first model tested, the GWL Checkout Model (CM), was a relatively simple model with a secondary objective of restoration and development of processes and methods for design, fabrication, testing, and data analysis of a representative ground wind loads model. In addition, parametric variations in surface roughness, Reynolds number, and protuberances (on/off) were investigated to determine effects on GWL characteristics. The second windtunnel model, the Ares I-X GWL Model, was significantly more complex and representative of the Ares I-X FTV and included the addition of simplified rigid geometrically-scaled models of the Kennedy Space Center (KSC) Mobile Launch Platform (MLP) and Launch Complex 39B primary structures. Steady and dynamic base bending moment as well as model response and steady and unsteady pressure data was acquired during the testing of both models. During wind-tunnel testing of each model, flow conditions (speed and azimuth) where significant WIO occurred, were identified and thoroughly investigated. Scaled data from the Ares I-X GWL model test was used in the determination of worst-case loads for the analysis of Ares I-X FTV design wind conditions. Finally, this paper includes a brief discussion of the limited full-scale GWL data acquired during the rollout and on-pad stay of the Ares I-X FTV that was launched from KSC on October 28, 2009.

Keller, Donald F.↗
NASA NTRS1990

Innovative design of composite structures: Axisymmetric deformations of unsymmetrically laminated cylinders loaded in axial compression

The study focuses on the axisymmetric deformation response of unsymmetrically laminate cylinders loaded in axial compression by known loads. A geometrically nonlinear analysis is used. Though buckling is not studied, the deformations can be considered to be the prebuckling response. Attention is directed at three 16 layer laminates: a (90 sub 8/0 sub 8) sub T; a (0 sub 8/90 sub 8) sub T and a (0/90) sub 4s. The symmetric laminate is used as a basis for comparison, while the two unsymmetric laminates were chosen because they have equal but opposite bending-stretching effects. Particular attention is given to the influence of the thermally-induced preloading deformations that accompany the cool-down of any unsymmetric laminate from the consolidation temperature. Simple support and clamped boundary conditions are considered. It is concluded that: (1) The radial deformations of an unsymmetric laminate are significantly larger than the radial deformations of a symmetric laminate, although for both symmetric and unsymmetric laminates the large deformations are confined to a boundary layer near the ends of the cylinder; (2) For this nonlinear problem the length of the boundary layer is a function of the applied load; (3) The sign of the radial deformations near the supported end of the cylinder depends strongly on the sense (sign) of the laminate asymmetry; (4) For unsymmetric laminates, ignoring the thermally-induced preloading deformations that accompany cool-down results in load-induced deformations that are under predicted; and (5) The support conditions strongly influence the response but the influence of the sense of asymmetry and the influence of the thermally-induced preloading deformations are independent of the support conditions.

Hyer, M. W.↗
DOE OSTI2016

Rotating Disk Slurry Au Electrodeposition at Unsupported Carbon Vulcan XC-72 and Ce 3+ Impregnation for Ethanol Oxidation in Alkaline Media

A robust electrodeposition method consisting of the rotating disk slurry electrode (RoDSE) technique to obtain Au nanoparticles highly dispersed on a conductive carbonaceous support, i.e., Vulcan XC-72R, for ethanol electrooxidation reaction in alkaline media was developed. Ceria was used as a cocatalyst using a Ce(III)-EDTA impregnation method in order to enhance the catalytic activity and improve the catalyst’s overall stability. Furthermore, the RoDSE method used to obtain highly dispersed Au nanoparticles does not require the use of a reducing agent or stabilizing agent, and the noble-metal loading was controlled by the addition and tuning of the metal precursor concentration. Inductively coupled plasma and thermogravimetric analysis indicated that the Au loading in the catalyst was 9 %. We determined the particle size and characteristic Au fcc crystal facets by X-ray diffraction. The morphology of the catalyst was also investigated using electron microscopy techniques. In addition, X-ray absorption spectroscopy was used to corroborate the presence and identify the oxidation state of Ce in the system and to observe if there are any electronic interactions within the 8 % Au/CeO x /C system. Cyclic voltammetry of electrodeposited 9 % Au/C and Ce-promoted 8 % Au/C showed a higher catalytic current density for ethanol oxidation when compared with commercially available catalysts (20 % Au/C) of a higher precious metal loading. Additionally, we report a higher stability toward the ethanol electrooxidation process, which was corroborated by 1 mV/s linear sweep voltammetry and chronoamperometric studies.

36 MATERIALS SCIENCE↗
NASA NTRS1954

Analytical investigation of off-design performance of a transonic turbine

The off-design performance and a breakdown of the losses of a transonic turbine were determined by an analytical method that was previously developed for turbines of more conservative design. The analytically obtained performance map is compared with the performance map obtained from an experimental investigation of the turbine. The rotor hub conditions of incidence angle, relative Mach number, and reaction calculated from the analytical results are compared with those calculated from experimental data. The loss breakdown obtained for the transonic turbine did not differ substantially from that previously obtained from a turbine of more conservative design, except that large stator-exit shock losses were predicted for the transonic turbine at low speeds. The trends of the rotor hub incidence angle, relative Mach number, and reaction calculated from the analytical results agreed well with those calculated from the experimental data over the performance range. These trends indicate that, compared with a turbine of more conservative design, the transonic turbine operated over a much smaller range of incidence angle, a much wider range of rotor relative Mach number, and at a considerably lower level of reaction. Good over-all agreement was obtained between the analytically predicted performance and the experimental performance, except at 40-percent design speed, where in the analysis the stator reached limiting loading before the rotor choked. Since this discrepancy resulted from errors in the simplifying assumptions used in the analysis, it is regarded as a limitation in the analytical method as applied to a transonic turbine.

Whitney, Warren J↗
NASA NTRS1990

Response of laminated composite flat panels to sonic boom and explosive blast loadings

This paper deals with a theoretical analysis of the dynamic response of shear deformable symmetrically laminated rectangular composite flat panels exposed to sonic boom and explosive blast loadings. The pertinent governing equations incorporating transverse shear deformation, transverse normal stress, as well as the higher-order effects are solved by using the integral-transform technique. The obtained results are compared with their counterparts obtained within the framework of the first-order transverse shear deformation and the classical plate theories and some conclusions concerning their range of applicability are outlined. The paper also contains a detailed analysis of the influence played by the various parameters characterizing the considered pressure pulses as well as the material and geometry of the plate.

Librescu, L.↗
NASA NTRSDate not supplied

An Improved Weighted Least Squares Algorithm for the Analysis of Strain-Gage Balance Calibration Data

An improved version of an algorithm is presented that uses a weighted least squares fit of balance calibration data for the generation of the balance load prediction equations. The weighted least squares fit assigns a weighting factor between zero and one to each calibration data point that depends on a simple count of the number of intentionally loaded balance gages. The greater the number of the loaded gages is, the smaller a data point's weighting factor becomes. This strategy has two advantages. First, single-component loads become more influential during the regression analysis of the calibration data. In addition, the negative influence of load schedule asymmetries on the regression analysis results can more effectively be controlled. The original algorithm of 2017 was improved in 2020. Now, gage output differences relative to the natural zeros are exclusively used as input for the determination of the number of intentionally loaded gages. The improved weighted least squares fit can be applied with both the Non-Iterative Method and the Iterative Method that are used for the balance load prediction in the aerospace testing community. Machine calibration data of a force balance is used to illustrate benefits of the application of the improved weighted least squares fit of balance calibration data.

strain-gage balance↗
NASA NTRS1979

Rail shear test method

The results of both an experimental test program and a finite element analysis of selected graphite/polyimide rail shear test specimens are discussed. The two dimensional finite element analysis includes both mechanical and thermal loading (differential expansion) of the specimens and their elastic rails. Parameters in this analysis of unidirectional and symmetric, balanced angle-ply laminates include ply layup angles, the effect of flexible rails, the method of load introduction to the specimen and the effect of uniform heating of the specimen and rails. Two types of tensile rail shear fixtures were investigated experimentally: a uniform thickness, bolted-rail shear fixture loaded diagonally across the specimen test section; and a tapered thickness, bonded-rail shear fixture loaded axially along the center-line of the specimen test section. Test results include room-temperature and 589K strain data taken from the center of the specimen test section during loading.

Garcia, R.↗
DOE OSTI2011

Magnifying lens for 800 MeV proton radiography

This article describes the design and performance of a magnifying magnetic-lens system designed, built, and commissioned at the Los Alamos National Laboratory (LANL) for 800 MeV flash proton radiography. The technique of flash proton radiography has been developed at LANL to study material properties under dynamic loading conditions through the analysis of time sequences of proton radiographs. The requirements of this growing experimental program have resulted in the need for improvements in spatial radiographic resolution. To meet these needs, a new magnetic lens system, consisting of four permanent magnet quadrupoles, has been developed. This new lens system was designed to reduce the second order chromatic aberrations, the dominant source of image blur in 800 MeV proton radiography, as well as magnifying the image to reduce the blur contribution from the detector and camera systems. The recently commissioned lens system performed as designed, providing nearly a factor of three improvement in radiographic resolution.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2018

MSiReader v1.0: Evolving Open-Source Mass Spectrometry Imaging Software for Targeted and Untargeted Analyses

A major update to the mass spectrometry imaging (MSI) software MSiReader is presented, offering a multitude of newly added features critical to MSI analyses. MSiReader is a free, open-source, and vendor-neutral software written in the MATLAB platform and is capable of analyzing most common MSI data formats. A standalone version of the software, which does not require a MATLAB license, is also distributed. The newly incorporated data analysis features expand the utility of MSiReader beyond simple visualization of molecular distributions. The MSiQuantification tool allows researchers to calculate absolute concentrations from quantification MSI experiments exclusively through MSiReader software, significantly reducing data analysis time. An image overlay feature allows the incorporation of complementary imaging modalities to be displayed with the MSI data. A polarity filter has also been incorporated into the data loading step, allowing the facile analysis of polarity switching experiments without the need for data parsing prior to loading the data file into MSiReader. A quality assurance feature to generate a mass measurement accuracy (MMA) heatmap for an analyte of interest has also been added to allow for the investigation of MMA across the imaging experiment. Most importantly, as new features have been added performance has not degraded, in fact it has been dramatically improved. These new tools and the improvements to the performance in MSiReader v1.0 enable the MSI community to evaluate their data in greater depth and in less time. .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1985

Development and test of advanced composite components. Center Directors discretionary fund program

This report describes the design, analysis, fabrication, and test of a complex bathtub fitting. Graphite fibers in an epoxy matrix were utilized in manufacturing of 11 components representing four different design and layup concepts. Design allowables were developed for use in the final stress analysis. Strain gage measurements were taken throughout the static load test and correlation of test and analysis data were performed, yielding good understanding of the material behavior and instrumentation requirements for future applications.

Faile, G.↗
NASA NTRS2011

Utilizing Photogrammetry and Strain Gage Measurement to Characterize Pressurization of Inflatable Modules

This paper focuses on integrating a large hatch penetration into inflatable modules of various constructions. This paper also compares load predictions with test measurements. The strain was measured by utilizing photogrammetric methods and strain gages mounted to select clevises that interface with the structural webbings. Bench testing showed good correlation between strain data collected from an extensometer and photogrammetric measurements, even when the material transitioned from the low load to high load strain region of the curve. The full-scale torus design module showed mixed results as well in the lower load and high strain regions. After thorough analysis of photogrammetric measurements, strain gage measurements, and predicted load, the photogrammetric measurements seem to be off by a factor of two.

Mohammed, Anil↗
DOE OSTI2013

2012 White Book, Pacific Northwest Loads and Resources Study

The White Book is a planning analysis produced by BPA that informs BPA of its load and resource conditions for sales and purchases. The White Book provides a 10-year look at the expected obligations and resources in the Federal system and PNW region. The White Book is used as a planning tool for the Columbia River Treaty (Treaty) studies, as an information tool for customers and regional interests, and as a publication of information utilized by other planning entities for their analyses. The White Book is not used to guide day-to-day operations of the Federal Columbia River Power System (FCRPS) or determine BPA revenues or rates.

White book, Pacific Northwest Loads and Resources ↗
DOE OSTI2021

Fuel/Basket Degradation Modeling Summary

This report documents the activities in a preliminary phase of development for three models: 1) waste package breach model, 2) fuel/basket degradation model, and 3) dual-purpose canister (DPC) crush model. The waste package breach model describes the coupling of mass flow, heat transport, and canister shell deformation in response to a heat-generating (criticality) event. The fuel/basket degradation model describes potential weakening and disaggregation of the DPC structure from corrosion, possibly accelerated by seismic ground motion. Progressively degraded three-dimensional (3D) configurations of the fuel, basket, and shell are generated for future analysis of reactivity (with as-loaded DPC fuel characteristics). Another important application for the fuel/basket degradation model is validation of the two stylized degradation cases currently being used by other investigators for analysis of the as-loaded DPC inventory under disposal conditions. The DPC crush model investigates stability of a typical DPC after breach of the disposal overpack allows fluids from the repository near-field environment to penetrate and externally pressurize the canister shell. Preliminary results show that large deformation of the DPC could occur for external pressure on the order of 10 to 15 MPa, or the shell could be stable (not collapse) with pressure of 20 MPa or greater if the basket plates are fully welded at the connections.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1983

Thermal Elastohydrodynamic Lubrication of Spur Gears

Analysis and computer program (TELSGE) predict variations of dynamic load and surface temperature and lubricant film thickness along contacting path of pair of involute spur gears. Analysis of dynamic load includes effect of gear inertia, effect of load sharing of adjacent teeth, and effect of variable tooth stiffness obtained by element method. TELSGE written in FORTRAN IV.

Wang, K. L.↗
NASA NTRS1987

Integrated analysis and applications

A select overview is provided of ongoing research focusing on the development and verification of integrated structural analysis and optimal design capabilities for advanced aerospace propulsion and power systems. Subjects discussed include the following: (1) Composites - analytical models (composite mechanics), integrated computational methods, and characterization of composite structural response and durability for resin-, metal-, and ceramic-matrix systems; (2) Advanced inelastic analysis - algorithm/numerical methods for more accurate and efficient analysis; (3) Constitutive modeling - theoretical formulation and characterization of thermoviscoplastic material behavior; (4) Computational simulation - engine structures from components to assembly, and up to an entire engine system subjected to simulated test-stand and mission load histories; (5) Probabilistic structural analysis - quantification of the effects of uncertainty in geometry, material, loads, and boundary conditions on structural response for true reliability assessment; and (6) Interdisciplinary optimization - incorporation of mathematical optimization and multidisciplinary analyses to provide streamlined, autonomous optimal design systems.

Hopkins, Dale A.↗
NASA NTRS2008

Assessment of the LC-2 Prelaunch Fatigue Spectra of the CM-to-SM Flange Weld

The pad stay and rollout components of the Ares I-X life cycle can generate cyclic stress oscillations to the vehicle that could initiate and grow fatigue cracks from weld defects. The Ares I-X Project requested that a study be performed to determine if stabilization of the vehicle is required to reduce the stresses that could initiate and grow fatigue cracks at the flange-to-skin weld of the Command Module (CM) and Service Module (SM) interface. A fatigue crack growth analysis was conducted that used loads (LC-2) and stress analyses developed by the Ares I-X Project and utilized material data and analysis methods developed by a critical initial flaw size (CIFS) analysis conducted by NASA Engineering and Safety Center (NESC) for the Upper Stage Simulator (USS) of the Ares I-X vehicle. A full CIFS analysis for the CM-to-SM flange-to-skin weld was not performed because the full flight spectrum was not provided and was not necessary to answer the question posed by the Ares I-X Project. Instead, an approach was developed to determine if the crack growth due to the pad stay and rollout components of the flight spectrum would adversely influence the CIFS. The approach taken used a number of conservative assumptions that eliminated the need for high-fidelity analyses and additional material testing, but still provided a bounding solution for the uncertainties of the problem. The results from this analysis indicate that the LC-2 pad stay and rollout spectrum components would not produce significant fatigue crack growth on the CM-to-SM flange-to-skin weld. Thus, from a fatigue crack growth standpoint, no stabilization is required to reduce the LC-2 pad stay and rollout cyclic stresses on the CM-to-SM flange-to-skin weld.

Dawicke, David S.↗
DOE OSTI2025

Refining Control, Charging, and Battery Chemistry for CO 2 e Savings in Heavy-Duty Off-Road Plug-In Series Hybrid

With current and future regulations continuing to drive reductions in carbon dioxide equivalent (CO 2 e) emissions in the on-road industry, the off-road industry is also likely to be regulated for fuel and CO 2 e savings. This work focuses on converting a heavy-duty off-road material handler from a conventional diesel powertrain to a plug-in series hybrid, achieving a 49% fuel reduction and 29% CO 2 e reduction via simulation. Control strategies were refined for energy savings, including a regenerative braking strategy to increase regenerative braking and a load-following hydraulic strategy to decrease electrical energy consumption. The load-following hydraulic control shuts off the hydraulic electric machine when it is not needed—an approach not previously seen in a load-sensing, pressure-compensated system. Furthermore, these strategies achieved a 24.1% fuel savings, resulting in total savings of 61% in fuel and 41% in CO 2 e in the plug-in series compared to the conventional machine. Beyond control strategies, this study evaluated battery chemistry and charging strategy refinements for total cost of ownership (TCO) and lifetime CO 2 e. LFP batteries emerged as the most cost-effective and least emitting due to their longer lifespan, which reduced replacement frequency. Charging comparisons showed that Level 2 charging (L2C) typically resulted in lower TCO but higher lifetime CO 2 e than DC fast charging (DCFC). DCFC costs were heavily influenced by local demand charges, and DCFC emissions were heavily influenced by local grid emissions.

33 ADVANCED PROPULSION SYSTEMS↗