Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Non-Destructive Characterization of Subsurface Residual Stress Fields and Correlation with Microstructural Conditions in a Shot-Peened Inconel Component

Shot-peening is an important surface treatment used in a preventative way to guard against fatigue failures. The residual stress state imparted by shot-peening deters the formation and propagation of surface cracks. In this paper, we describe the measurement of residual stresses in an Inconel, IN100, sample using lattice strains measured using High Energy X-ray Diffraction (HEXD) and a Bi-Scale Optimization Method (BSOM). HEXD enabled rapid, non-destructive lattice strain measurements over a large region of the sample. Subsurface strains were obtained using a conical slit setup. The BSOM utilizes a macroscale representation of the sample and a spherical harmonic-based crystal scale representation of crystal orientation space at each experimental point (diffraction volume). A roughly biaxial stress state was predicted with a von Mises equivalent stress between 300 MPa and 400 MPa near the surface. The layer of material with high residual stress induced by shot-peening was found to be approximately 1 mm thick. Diffraction peak width, EBSD, and microhardness measurements were also made on the same sample, which rendered more qualitative measures of the plasticity-related effects of the shot-peening induced residual stress field. All of these measurements show a dimishing shot-peening plasticity with the increasing depth.

42 ENGINEERING↗

iCHORD-SI combination as an alternative to EDS-EBSD coupling for the characterization of γ-γ′ nickel-based superalloy microstructures

Highlights: • A new method to get orientation maps discriminating the gamma and gamma’ phases of Ni superalloys is described. • The method combines the iCHORD technique with secondary ion imaging. • The new method resolves precipitates down to 150 nm within a reasonable acquisition time. - Abstract: Because they exhibit very similar diffraction patterns, the γ and γ′ phases of nickel-based superalloys cannot be distinguished by the conventional EBSD technique alone. This paper presents an original method which discriminates those phases on an orientation map by exploiting their chemical differences. Performed with a Focused Ion Beam (FIB) microscope, the method is the combination of the ion CHanneling ORientation Determination technique (iCHORD) – recently developed by Langlois et al. [1] – with the chemical information obtained from Secondary Ion (SI) images. The performances of the method are compared to the EDS-EBSD coupling which also discriminates phases based on their chemical compositions. Applied filters, angular resolution, spatial resolution of the phase discrimination and acquisition time are discussed. It results that the iCHORD–SI combination offers an orientation map with an angular resolution slightly decreased compared to that of the EBSD technique, but with a good phase resolution (down to 150 nm) and within a reasonable acquisition time. Thus, the iCHORD–SI combination appears to be an interesting method for the crystallographic systems where phases are difficult to discriminate by the EBSD technique alone but present a significant chemical contrast.

36 MATERIALS SCIENCE↗

Synthesis and characterization of lignin-based carbon materials with tunable microstructure

Lignin-based carbons can be used as a low-cost alternative to graphite and petroleum-based carbons enabling the production of sustainable, functional carbon materials for various applications. The microstructure development of these carbons can be controlled through chemical modification of the lignin precursor and choice of carbonization parameters. In this work, microstructured carbon materials are synthesized from lignin using a combination of chemical modification and carbon fiber processing techniques. Lignin is modified by incorporating different ester groups which results in a precursor highly compatible with melt processing using the fiber extrusion technique and conversion into microstructured carbons by oxidative stabilization and subsequent carbonization. Furthermore, the impact of esterifications on precursor chemistry and carbonizations is investigated. A nuclear magnetic resonance study of modified lignins shows characteristic spectral changes as a result of esterifications. Ultrahigh resolution Fourier transform ion cyclotron resonance mass spectrometry shows the modification process does not affect the polymeric character of the lignin backbone. Esterifications result in moderate shifts in O:C and H:C ratios. Thermogravimetric analysis of lignins reveals distinct differences in mass loss trends during oxidations and carbonizations.

anode↗

USE OF TWO-PISTON SPLAT QUENCHING TO INVESTIGATE & CHARACTERIZE THE IMPACT OF COMPOSITIONAL VARIATIONS ON RAPID SOLIDIFICATION MICROSTRUCTURES & SUB-MICROSCALE FEATURES IN STAINLESS STEEL ALLOY.

The objective of this dissertation was to use two-piston splat quenching (SQ) to investigate the impact of compositional modifications on the solidification and microstructure of rapidly solidified austenitic stainless steels (SS) and to demonstrate the ability of SQ to quickly and effectively simulate rapid solidification conditions similar to those found in powder bed fusion (PBF) additive techniques. PBF techniques like laser powder bed fusion (LPBF) are being implemented across a breadth of research and industrial applications to create parts with complex geometries and performance capabilities while pushing the current limits of processing conditions and understanding of material systems. In this work, SQ was used to experimentally produce rapid solidification in 20+ unique austenitic SS compositions with systematic variations of the chrome and nickel equivalency ratio (Cr/Nieq) through targeted compositional modifications. From the targeted change of Cr, Ni, and Mo concentrations in rapidly solidified SS alloys, the ferrite solidification mode was found to be the primary solidification mode at significantly lower Cr/Nieq than previously predicted for RS. Also, decreasing concentrations of Fe at a constant Cr/Nieq ratio (i.e., different Fe isopleths), or increased Mo concentrations at a constant Cr/Nieq ratio were found to suppress the ferrite to austenite massive transformation when compared to alloys with lower concentrations at the same Cr/Nieq. Using an established empirical relationship between cell size and cooling rate, the SQ technique was estimated to produce cooling rates between 106 and 108 K/s. Thermal gradients were extracted from 2-D heat transfer simulations of the SQ solidification event and used with these cooling rates to produce solidification rate estimates for SQ which were between 0.4-1.6m/s. The primary solidification mode was observed to be the determining factor in which elements segregated to the cell boundaries during RS, for which Cr and Mo were the main elements to segregate during primary austenite solidification and Ni during primary ferrite solidification. Finally, the solidification rates and conditions produced by SQ experiments resulted in similar microstructures, features, and microsegregation to what was found in LPBF samples of the same feedstock.

Hasenbusch, Zachary↗

Effect of pre-cold rolling on the evolution of microstructure, microtexture, and mechanical properties of the mushy state rolled in-situ Al-4.5Cu-5TiB2 composite

Highlights: • Microstructure-Microtexture evolution study of the mushy state rolled composite (MRC) and MRC with pre-cold rolling (PCMRC). • The Microstructure and microtexture were characterized using SEM, EBSD, and TEM. • Exactly opposite trends in micro-hardness variation across the thickness of MRC and PCMRC were discussed. • The PCMRC exhibited the best combination of hardness, strength, and ductility. • A proper microstructure-microtexture-property correlation was established with experimental evidence. The mushy state rolling has been found as a promising technique for near-net forming of the cast Al-4.5 wt% Cu-5 wt% TiB{sub 2} in-situ composite to obtain microstructural refinement and moderate mechanical properties. Cold rolling with 30% reduction in thickness was carried out before mushy state rolling, for achieving a relatively more homogeneous distribution of CuAl{sub 2}-TiB{sub 2} particles as well as an appropriate microstructure to enhance the mechanical properties. A comparative investigation on the microstructural and microtextural evolution, along with mechanical properties of both the mushy state rolled composite (MRC) and pre-cold rolled mushy-state rolled composite (PCMRC) was performed, and the microstructure-property correlation was established. The PCMRC exhibited the lowest homogenized lengthscale parameter (L{sub H} 29 μm) indicating the maximum uniformity of particle distribution, computed with the help of multi-scalar analysis of area fractions (MSAAF) technique. Electron back-scattered diffraction (EBSD) and transmission electron microscopy (TEM) studies revealed the presence of fine sub-grains within centrally located deformed Al grains due to dynamic recovery, as well as the particle stimulated nucleation of equiaxed fine Al grains by dynamic recrystallization or rapid solidification of liquid near edges for both the investigated composites. The PCMRC displayed a superior combination of hardness (96.82 ± 4.5 HV{sub 5kgf}), 40% higher ultimate tensile strength (301.4 ± 1.8 MPa), and 68% more uniform elongation (30.8% ± 0.5%), compared to the MRC. The improvement in mechanical properties is attributed to the uniform particle distribution and presence of both higher density of low angle boundaries and recrystallized grains adjacent to the particles, obtained from prior cold rolling.

36 MATERIALS SCIENCE↗

High Entropy Alloys: Irradiation

High entropy alloys (HEAs) have been considered as structural materials for nuclear applications due to their promising mechanical properties and radiation resistance. For this purpose, irradiation-induced defect evolution and microstructure change have been characterized to evaluate the irradiation performance of different HEAs. This article reviews recent advances in understanding the irradiation response of HEAs, including the effect of disordered states on the defect energy landscape and defect evolution, irradiation-induced microstructure changes, void swelling, phase stability, mechanical properties under irradiation, as well as the He irradiation effects.

Zhao, Shijun↗

Deformation and damage of sintered low-porosity aluminum under planar impact: microstructures and mechanisms

In this paper, plate impact experiments are conducted to study compaction and spallation of 5% porosity aluminum. Free surface velocity histories, the Hugoniot elastic limit (HEL), and spall strengths are obtained at different peak stresses and pulse durations. Scanning electron microscopy, electron backscatter diffraction, and X-ray computed tomography are used to characterize 2D and 3D microstructures. 3D void topology analyses yield rich information on size distribution, shape, orientation, and connectivity of voids. HEL decreases/increases with sample thickness/impact velocity and approaches saturation. Its tensile strength increases with increasing peak stress and shock-induced densification. With the enhanced compaction under increasing impact velocities, spall damage modes change from growth of original voids to inter-particle crack propagation and to “random” nucleation of new voids. Such a change in damage mechanism also gives rise to a distinct decrease in damage extent at high impact velocities. Finally, compaction induces strain localizations around the original voids, while subsequent tension results in grain refinement, and shear deformation zones between staggered cracks.

36 MATERIALS SCIENCE↗

Investigation on Equal-Channel Angular Pressing-Induced Grain Refinement in an Aluminum Matrix Composite Reinforced with Al-Cu-Ti Metallic Glass Particles

In the present study, a homogeneous ultrafine grain structure composite consisting of metallic glass particles reinforcements was developed by equal-channel angular pressing (ECAP) process. The microstructure of composite was characterized using x-ray diffraction (XRD), transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD) techniques. The uniaxial compression test was used to determine the mechanical properties. The mechanisms of grain refinement during ECAP process were discussed based on the microstructural evolutions. A composite was successfully produced after four passes of ECAP, having an average grain size of 610 nm and compressive yield strength of 242 MPa. Also, the yield strength of composite after each pass was quantitatively estimated by considering all the effective strengthening mechanism. The findings showed that the dislocations strengthening mechanism with contribution of more than 50% plays a major role in strengthening the composite. There was a negligible gap between the experimental and theoretical values of yield strength for all ECAP pass numbers.

36 MATERIALS SCIENCE↗

Geometry-Induced Spatial Variation of Microstructure Evolution During Selective Electron Beam Melting of Rene-N5

High gamma prime (γ') nickel-based alloys produced by selective electron beam melting are of interest to the turbine industry which requires control of microstructure in relation to loading conditions within complex component geometry. Welding literature predicts cracking and microstructure evolution as a function of alloy composition and process parameters in this class of alloys. In addition, Additive manufacturing causes variations in the above conditions due to the interaction of geometry on processing and heat transfer. The influence of geometry on processing conditions was explored for alloy Rene N5 by characterizing the solidification grain microstructure and solid-state precipitation. A Semi-Analytical Heat Transfer Model was employed to explain the resulting variation in solidification grain morphology that occurred due to the part geometry. Finally, the as-built precipitation structure was found to vary as a function of build height and had no correlation to the solidification grain structure or the layer geometry.

36 MATERIALS SCIENCE↗

Chemical banding revealed by chemical etching in a cold-rolled metastable stainless steel

The current work describes the metallographic characterization of the initial microstructure of a cold rolled precipitation hardening semi-austenitic stainless steel (12Cr–9Ni–4Mo–2Cu–1Ti, in wt.%). The use of the Lichtenegger and Blöch (L–B) color etching solution has been shown to reveal not only the phases present in the microstructure, but also the existence of chemical banding along the rolling direction. The L–B reagent has been found to color the microstructure in bands depending on what alloying elements have segregated to each band. Two-dimensional electron probe microanalysis (EPMA) maps have shown that Ni, Cu and Ti segregate together in the bands, while Cr has an opposite behavior. Mo has a mixed segregation behavior although much weaker than the other elements and more prompt to segregate like Ni does. A direct comparison of light optical micrographs with the EPMA maps of the same area of the microstructure has enable to establish a direct relationship between the alloying element band concentration and the resulting etching color contrast obtained with the L–B reagent. Thermodynamic calculations predict that solidification in this steel takes place with ferrite as the primary phase. Equilibrium partitioning coefficient calculations seem to support the observed segregation patterns. - Highlights: • A cold rolled metastable stainless steel has been characterized thoroughly. • EPMA shows that Ni, Cu and Ti segregate together; Cr in an opposite way. • L–B color etching is sensitive to the segregation of these chemical elements. • This chemical banding has been reduced by applying a homogenization heat treatment. • Partitioning coefficient calculations agree with the observed segregation patterns.

36 MATERIALS SCIENCE↗

Behavior of Au Species in Au/Fe 2 O 3 Catalysts Characterized by Novel In Situ Heating Techniques and Aberration-Corrected STEM Imaging

The recent advent of a novel design of in situ heating technology for electron microscopes has permitted unprecedented control of elevated temperature studies of catalytic materials, particularly when coupled with the sub- ngstr m imaging performance of a modern aberration-corrected scanning transmission electron microscope (STEM). In using micro-electro-mechanical-systems (MEMS)-based Aduro heating chips from Protochips, Inc. (Raleigh, NC, USA) it allows nearly instantaneous heating and cooling of catalyst powders, while avoiding the effects of temperature ramping as experienced with standard heating stages. The heating technology also provides stable operation limited only by the inherent drift in the microscope stage, thus allowing full image resolution to be achieved even at elevated temperatures. Our study details the use of both the high X-Y spatial resolution in both dark-field and simultaneous bright-field imaging, along with the high resolution in Z (depth sectioning) provided by the large probe incidence semiangle in the aberration-corrected instrument, to characterize the evolution of microstructure in a commercial Au/Fe 2 O 3 water-gas shift catalyst during elevated temperature treatment. The phenomenon of Au diffusion to the surface of hematite support particles to form discrete crystalline Au nanoparticles in the 1-2 nm size range, after a prior leaching treatment to remove surface Au species has been characterized.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The effect of neutron irradiation on conventional and nanocrystalline nickel: NSUF Work Package UA-22PN080501 Milestone M3UA-22PN0805012 (Final Report)

Even though nanocrystalline materials (20-100 nm) present an unprecedented potential, scientific knowledge related to the effect of neutron irradiation on the mechanical properties and microstructure is still scarce. Most of the past studies were conducted using ion irradiation which may not have the same effect as neutron irradiation because of the smaller irradiation volume and the higher dose rate. To reach a firm conclusion on the potential of nanocrystalline materials for nuclear reactor applications, extensive study of model metals with different stacking fault energy (SFE) is required to elucidate their behavior in radiation environments. Nanocrystalline copper and nickel are typically chosen because they are commonly used as model FCC metals in studies of radiation effects. Nickel is an FCC metal with a high stacking-fault energy (~125 mJ/m 2 ) compared to copper (~45 mJ/m 2 ). Hence, microcrystalline and nanocrystalline nickel samples were irradiated in the INL’s Advanced Test Reactor (ATR), as a part of FY08 North Carolina State University NSUF Irradiation Experiment# 96 to evaluate the irradiation behavior of these materials. The objective of this FY20 NSUF project# 19122 is to perform PIE (at PNNL NSUF facility) on previously ATR-neutron irradiated (1.2 and 2.6 dpa; 80-89°C) nanocrystalline and microcrystalline nickel samples to investigate the changes in mechanical properties and microstructures and evaluate whether nanocrystalline nickel is relatively more radiation resistant compared to conventional microcrystalline nickel. To perform PIE at PNNL, sixteen neutron irradiated specimens (microcrystalline and nanocrystalline) were transferred from the NSUF Nuclear Fuels and Materials Library at INL. Experimental techniques such as SEM/EBSD, XRD, TEM, Vickers microhardness and tensile testing were employed to characterize the effect of neutron irradiation on the microstructure and mechanical properties of nanocrystalline nickel and compared them with corresponding characteristics of microcrystalline nickel.

36 MATERIALS SCIENCE↗

Influence of microstructure on replacement and porosity generation during experimental dolomitization of limestones

Replacement reactions commonly alter the multiscale pore structures of rocks during fluid-rock interactions. Analysis of these processes in various model fluid-rock systems during controlled laboratory experiments provides insights into the origins of microstructures found in natural materials. This study focused on understanding the effects of initial starting material permeability and resultant differences in transport pathways on porosity and mineralogical changes during limestone dolomitization.A series of replacement experiments (32–317 days in duration) have been conducted in which 1.59 cm (5/8 in.) diameter cores of two different limestones were reacted with saturated MgCl2 solutions at 200 °C. The Texas Cream (Austin Chalk) is a high-porosity, high-permeability limestone, whereas both the porosity and permeability of the Carthage Marble (Burlington Limestone) are relatively low. Altered limestones were imaged using scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), Time-of-Flight Secondary Ion Mass Spectrometry (ToF–SIMS) and electron microprobe analysis (EMPA). A representative grain boundary of the low-porosity limestone was targeted for a focused ion beam (FIB) lift-out and characterized using transmission electron microscopy (TEM). These results were coupled with analyses of radial changes in the porosity distribution of the core derived from X-ray and neutron small- and ultra-small angle scattering ((U)SANS/(U)SAXS).The high-porosity/permeability limestone showed a four times faster bulk replacement rate than the lower-porosity/permeability material, and a different mechanism of porosity development. For the low-porosity limestone, a two-stage replacement occurred, with the reacted region of the core consisting of an inner rim in which the limestone was replaced by two calcite-dolomite solid solutions, and an outer rim in which the dolomite was replaced by magnesite. Elongated pores formed along grain boundaries at the initial limestone/dolomite reaction interface, and additional nanometer-scale porosity was formed at the secondary magnesite replacement rim. Grain boundaries were identified as preferential pathways for transport leading to dolomitization and a grain boundary diffusion rate was calculated based on microstructural characterization. In contrast, replacement in the high-porosity limestone was accompanied by porosity generation through replacement of individual grains by dolomite throughout the sample and, in longer runs, magnesite in outer parts of the core. These observations emphasize that both the mechanisms of the replacement reaction and the microstructure and chemistry of the replaced product are contingent on the initial structure of the starting material.

36 MATERIALS SCIENCE↗

Oxygen deficiency induced deterioration in microstructure and magnetic properties at Y{sub 3}Fe{sub 5}O{sub 12}/Pt interface

Transport efficiency of pure spin current across the ferromagnetic films adjacent with a nonmagnetic metal is strongly dependent on the spin mixing conductance, which is very sensitive to atomic-level interface conditions. Here, by the means of advanced electron microscopy techniques, atomic structure, electronic structure, and magnetic properties at Y{sub 3}Fe{sub 5}O{sub 12} (YIG)/Pt interface are detailed characterized to correlate the microstructure and magnetic properties with interfacial transport properties. It is found that the order-disorder structure transformation at the interface is accompanied with oxygen deficiency, thus the reduced iron valence and the break of magnetic atom-O-magnetic atom bridges, which is responsible for superexchange interaction and magnetic order. It is also found that the magnetic moment of interfacial iron ions is decreased. The disorder interfacial layer with suppressed magnetism finally contributes to the declined spin transport efficiency. Our results provide the knowledge to control and manipulate the interfacial structure and properties in order to obtain higher spin transport efficiency.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Microstructure reconstruction of battery polymer separators by fusing 2D and 3D image data for transport property analysis

A new approach to generate high-fidelity 3D microstructure reconstructions by leveraging resolution and sample volume characteristics from 2D and 3D microscopy methods is presented here. This approach is employed to model the microstructure of a highly orthotropic polypropylene separator used in lithium-ion batteries, which have challenging multi-scale features of fibrils (<100 nm) and lamellae (>100 nm) to resolve in 3D. Phase contrast nano X-ray computed tomographic data are used to reconstruct the lamellae phase, while 2D scanning electron microscopy data are used to characterize sub-100 nm microstructure features such as the thin fibrils that are beyond the effective resolution of X-ray computed tomography. Fibril geometries are reconstructed stochastically based on the 2D higher resolution data, and integrated with the lamellae geometries in 3D space. Transport property analyses are performed to investigate the bias of microstructure models without considering the fibrils. A sensitivity study is also conducted to facilitate understanding of the relationship between microstructure characteristics and transport properties.

25 ENERGY STORAGE↗

In-situ single-grain peak profile measurements on Ti-7Al during tensile deformation.

High-energy three-dimensional X-ray diffraction with medium and high reciprocal space resolution was applied to study in situ tensile deformation of Ti-7Al specimens. Samples with planar and random dislocation microstructures were prepared and characterized by electron microscopy. Stress tensors of individual grains were obtained at several loads up to 2% deformation. The stress tensors were found to rotate, and resolved shear stresses were calculated. High-resolution reciprocal space maps of selected grains were recorded. Azimuthal and radial distributions were visualized and discussed in terms of idealized dislocation structures. Heterogeneous grain rotations were observed for the planar microstructure and found to be consistent with activation of the highest stressed basal slip system. Intra-granular strain gradients were detected in excess of the intrinsic radial dislocation peak broadening. The potential of combining the applied techniques with modeling to obtain multiple length-scale information during deformation of bulk specimens is discussed.

36 MATERIALS SCIENCE↗

In Situ Investigation of Chemomechanical Effects in Thiophosphate Solid Electrolytes

Solid-state batteries can suffer from catastrophic failure at high current densities due to solid electrolyte fracture, interface decomposition, or lithium filament growth. Failure is linked to chemomechanical material transformations that can manifest during electrochemical cycling. We systematically investigate how solid electrolyte microstructure and interfacial decomposition (e.g., interphase) affect failure mechanisms in lithium thiophosphates (Li3PS4, LPS) electrolytes. Kinetically metastable interphases are engineered with iodine doping, and microstructural control is achieved using milling and annealing processing techniques. In situ transmission electron microscopy reveals iodine diffusion to the interphase, and upon electrochemical cycling, pores are formed in the interphase region. In situ synchrotron tomography reveals that interphase pore formation drives edge fracture events, which are the origin of through-plane fracture failure. Fractures in thiophosphate electrolytes actively grow toward regions of higher porosity and are affected by heterogeneity in microstructure (e.g., porosity factor). This report provides fundamental design guidelines for high-performance solid-state batteries.

25 ENERGY STORAGE↗