SEARCH · Search NASA

Results for “MAGNETIC CONFINEMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

All sources NASA NTRS DOE OSTI

DOE OSTI2018

Grassy-ELM regime with edge resonant magnetic perturbations in fully noninductive plasmas in the DIII-D tokamak

Resonant magnetic perturbations (n=3 RMPs) are used to eliminate large amplitude ELMs and reduce the amplitude of weaker "grassy"-ELMs in DIII-D plasmas relevant to the ITER steady-state mission. Fully non-inductive discharges in the ITER shape and pedestal collisionality (n*e ≈ 0.05-0.15) are routinely achieved in DIII-D with RMP suppression of Type-I ELMs. The residual grassy-ELMs deliver a low peak heat flux to the divertor, within 50% of the inter-ELM heat flux, in plasmas with sustained high H-factor (H98y2≈1.2). These grassy-ELM plasmas have a pedestal width that is typically 10% of the poloidal minor radius and ≈50% wider than EPED model predictions. The operating window for RMP grassy-ELMs in edge magnetic safety factor and external torque is in the range required for a steady-state tokamak reactor, such as q95 between 5.3 and 7.1, and co-Ip neutral beam torque down to 0.7 Nm. Small amplitude RMPs (dBvac/B≈1.5x10-4) are sufficient to access this regime, consistent with the large amplification of the vacuum field by the plasma, typically 3-4x the amplification produced by ITER baseline plasmas due to the high pedestal pressure. Cyclic pulsations are observed in the pedestal and plasma magnetic response, consistent with theoretically predicted limit cycle behavior of magnetic island penetration and screening. The grassy ELMs are strongly modulated and sometimes fully suppressed during these pedestal pulsations, consistent with the stabilizing effect of resonant field penetration on peeling-ballooning mode stability. The use of low amplitude edge-resonant magnetic perturbations to access enhanced grassy-ELM operation in a naturally wide pedestal plasma with weak confinement degradation opens the possibility for further optimization of the steady-state tokamak by improved coupling between external fields and weakly stable modes of the plasma.

43 PARTICLE ACCELERATORS↗

DOE OSTI2021

High-performance ECRH at W7-X: experience and perspectives

The second operation phase of W7-X (OP1.2) showed the potential of exclusively electron cyclotron resonance heating (ECRH)-sustained plasma operations in stellarators. Employing multi-pass ECRH scenario in the second harmonic O-mode (O2-ECRH), stationary densities of up to 1.4 × 10 20 m -3 could be achieved. This scenario also made stationary divertor detachment possible, which is a reactor-relevant scenario for power and particle exhaust. At high densities and with sufficiently high density gradients for an improved ion confinement, the coupling between the electrons and ions was strong enough to bring the ion temperature to values above 3 keV and to the neoclassical limit for some magnetic configurations, thus enabling to test the W7-X neoclassical optimization. The planned enhancement of the ECRH performance will enable to advance towards reactor-relevant beta values and to investigate their stability and confinement of fast particles, which is a priority goal of W7-X.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2017

Improvements in Fabrication of Elastic Scattering Foils Used to Measure Neutron Yield by the Magnetic Recoil Spectrometer

The magnetic recoil spectrometer uses a deuterated polyethylene polymer (CD 2 ) foil to measure neutron yield in inertial confinement fusion experiments. Higher neutron yields in recent experiments have resulted in primary signal saturation in the detector CR-39 foils, necessitating the fabrication of thinner CD 2 foils than established methods could provide. A novel method of fabricating deuterated polymer foils is described. The resulting foils are thinner, smoother, and more uniform in thickness than the foils produced by previous methods. Here, these new foils have successfully been deployed at the National Ignition Facility, enabling higher neutron yield measurements than previous foils, with no primary signal saturation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2026

A new layered kagome strip structure Na 2 Co 3 (AsO 4 ) 2 (OH) 2 : static and dynamic magnetic properties

One-dimensional kagome strip chains share much of the same frustrated structural motif as two-dimensional kagome antiferromagnets, making them valuable for deepening our understanding of kagome lattice magnetism. In this paper, we report the hydrothermal synthesis and detailed structural and property characterization of Na 2 Co 3 (AsO 4 ) 2 (OH) 2 , a striped kagome system. The crystal structure was characterized using single crystal X-ray diffraction which reveals that Na 2 Co 3 (AsO 4 ) 2 (OH) 2 crystallizes in monoclinic crystal system C2/m. The structure features a one-dimensional kagome strip lattice built from Co 2+ ions and undergoes an antiferromagnetic transition at T N = 14 K. The magnetic ground state at zero field was characterized using neutron powder diffraction. Below the magnetic transition, Na 2 Co 3 (AsO 4 ) 2 (OH) 2 orders into an antiferromagnetic structure with a k-vector (0.5, 0.5, 0.5). In the proposed model, the Co1 moment is predominantly confined to the ac-plane while the Co2 moment is primarily aligned along the b-axis. Two flat bands were observed in the inelastic neutron spectra below the magnetic transition, 5 and 10 meV. Inelastic neutron spectra were modeled with a Heisenberg Hamiltonian including three nearest-neighbor exchange interactions (J 1 , J 2 , J 3 ) and strong single-ion anisotropy to stabilize the observed magnetic structure. Our study highlights the complexity of Co 2+ -based kagome strip magnetic lattice compound Na 2 Co 3 (AsO 4 ) 2 (OH) 2 which provides an excellent platform to broaden our understanding of the frustrated kagome magnetic lattice space.

Liurukara, Duminda S. [Oak Ridge National Laborato↗

DOE OSTI2017

Comparative H-mode density limit studies in JET and AUG

Identification of the mechanisms for the H-mode density limit in machines with fully metallic walls, and their scaling to future devices is essential to find for these machines the optimal operational boundaries with the highest attainable density and confinement. Systematic investigations of H-mode density limit plasmas in experiments with deuterium external gas fuelling have been performed on machines with fully metallic walls, JET and AUG and results have been compared with one another. Basically, the operation phases are identical for both tokamaks: the stable H-mode phase, degrading H-mode phase, breakdown of the H-mode with energy confinement deterioration usually accompanied by a dithering cycling phase, followed by the l-mode phase. The observed H-mode density limit on both machines is found close to the Greenwald limit (n/n GW = 0.8–1.1 in the observed magnetic configurations). The similar behavior of the radiation on both tokamaks demonstrates that the density limit (DL) is neither related to additional energy losses from the confined region by radiation, nor to an inward collapse of the hot discharge core induced by overcooling of the plasma periphery by radiation. It was observed on both machines that detachment, as well as the X-point MARFE itself, does not trigger a transition in the confinement regime and thus does not present a limit on the plasma density. It is the plasma confinement, most likely determined by edge parameters, which is ultimately responsible for the transition from H- to l-mode. The measured Greenwald fractions are found to be consistent with the predictions from different theoretical models, based on MHD instability theory in the near-SOL.

36 MATERIALS SCIENCE↗

DOE OSTI2017

Long-range spin wave mediated control of defect qubits in nanodiamonds

Hybrid architectures that combine nitrogen-vacancy (NV) centers in diamond with other materials and physical systems have been proposed to enhance the NV center’s capabilities in many quantum sensing and information applications. In particular, spin waves (SWs) in ferromagnetic materials are a promising candidate to implement these platforms due to their strong magnetic fields, which could be used to efficiently interact with the NV centers. Here we develop an yttrium iron garnet-nanodiamond hybrid architecture constructed with the help of directed assembly and transfer printing techniques. Operating at ambient conditions, we demonstrate that surface confined SWs excited in the ferromagnet (FM) can strongly amplify the interactions between a microwave source and the NV centers by enhancing the local microwave magnetic field by several orders of magnitude. Crucially, we show the existence of a regime in which coherent interactions between SWs and NV centers dominate over incoherent mechanisms associated with the broadband magnetic field noise generated by the FM. These accomplishments enable the SW mediated coherent control of spin qubits over distances larger than 200 um, and allow low power operations for future spintronic technologies.

36 MATERIALS SCIENCE↗

DOE OSTI2017

The Ingestion of Fluorescent, Magnetic Nanoparticles for Determining Fluid-uptake Abilities in Insects

Here, fluid-feeding insects ingest a variety of liquids, which are present in the environment as pools, films, or confined to small pores. Studies of liquid acquisition require assessing mouthpart structure and function relationships; however, fluid uptake mechanisms are historically inferred from observations of structural architecture, sometimes unaccompanied with experimental evidence. Here, we report a novel method for assessing fluid-uptake abilities with butterflies (Lepidoptera) and flies (Diptera) using small amounts of liquids. Insects are fed with a 20% sucrose solution mixed with fluorescent, magnetic nanoparticles from filter papers of specific pore sizes. The crop (internal structure used for storing fluids) is removed from the insect and placed on a confocal microscope. A magnet is waved by the crop to determine the presence of nanoparticles, which indicate if the insects are able to ingest fluids. This methodology is used to reveal a widespread feeding mechanism (capillary action and liquid bridge formation) that is potentially shared among Lepidoptera and Diptera when feeding from porous surfaces. In addition, this method can be used for studies of feeding mechanisms among a variety of fluid-feeding insects, including those important in disease transmission and biomimetics, and potentially other studies that involve nano- or micro-sized conduits where liquid transport requires verification.

36 MATERIALS SCIENCE↗

DOE OSTI2016

The locking and unlocking thresholds for tearing modes in a cylindrical tokamak

The locking and unlocking thresholds for tearing modes are in general different. In this work, the physics origin for this difference is illustrated from theory analysis, and a numerical procedure is developed to find both locking and unlocking thresholds. In particular, a new scaling law for the unlocking threshold that is valid in both weak and strong rotation regimes has been derived from the lowest amplitude of the RMP (resonant magnetic perturbation) allowed for the locked-mode solution. Above the unlocking threshold, the criterion for the phase-flip instability is extended to identify the entire locked-mode states. Two different regimes of the RMP amplitude in terms of the accessibility of the locked-mode states have been found. In the first regime, the locked-mode state may or may not be accessible depending on the initial conditions of an evolving island. In the second regime, the locked-mode state can always be reached regardless of the initial conditions of the tearing mode. The lowest RMP amplitude for the second regime is determined to be the mode-locking threshold. The different characteristics of the two regimes above the unlocking threshold reveal the underlying physics for the gap between the locking and unlocking thresholds and provide an explanation for the closely related and widely observed hysteresis phenomena in island evolution during the sweeping process of the RMP amplitude up and down across that threshold gap.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2017

Photonic-band-gap gyrotron amplifier with picosecond pulses

Here, we report the amplification of 250 GHz pulses as short as 260 ps without observation of pulse broadening using a photonic-band-gap circuit gyrotron traveling-wave-amplifier. The gyrotron amplifier operates with a device gain of 38 dB and an instantaneous bandwidth of 8 GHz. The operational bandwidth of the amplifier can be tuned over 16 GHz by adjusting the operating voltage of the electron beam and the magnetic field. The amplifier uses a 30 cm long photonic-band-gap interaction circuit to confine the desired TE 03 -like operating mode while suppressing lower order modes which can result in undesired oscillations. The circuit gain is >55 dB for a beam voltage of 23 kV and a current of 700 mA. These results demonstrate the wide bandwidths and a high gain achievable with gyrotron amplifiers. The amplification of picosecond pulses of variable lengths, 260–800 ps, shows good agreement with the theory using the coupled dispersion relation and the gain-spectrum of the amplifier as measured with quasi-CW input pulses.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2020

Evaluation method of beam instability in laser ion source using solenoid

In a laser ion source using solenoid field confinement, it is known that an ion beam becomes unstable in the certain range of a magnetic field. Although it is essential to quantify the instability when discussing the unstable region of the beam, it is difficult to evaluate the beam instability by peak current or the amount of charge because an irregular change of temporal profile occurs in addition to the shot-by-shot fluctuation of amplitude. In this study, I propose the most appropriate method to evaluate the beam instability using the difference from an average waveform. The validity of the new method was evaluated by comparing three evaluation methods (variation of maximum value, variation of integral of waveforms, and the proposed evaluation method) with the experimentally obtained waveforms with the stable and unstable regions of a solenoid field. The proposed method was verified to best represent the beam instability by laser-induced plasma.

43 PARTICLE ACCELERATORS↗

DOE OSTI2023

Characterization of fast magnetosonic waves driven by compact toroid plasma injection along a magnetic field

Magnetosonic waves are low-frequency, linearly polarized magnetohydrodynamic (MHD) waves commonly found in space, responsible for many well-known features, such as heating of the solar corona. In this work, we report observations of interesting wave signatures driven by injecting compact toroid (CT) plasmas into a static Helmholtz magnetic field at the Big Red Ball Facility at Wisconsin Plasma Physics Laboratory. By comparing the experimental results with the MHD theory, we identify that these waves are the fast magnetosonic modes propagating perpendicular to the background magnetic field. Additionally, we further investigate how the background field, preapplied poloidal magnetic flux in the CT injector, and the coarse grid placed in the chamber affect the characteristics of the waves. Since this experiment is part of an ongoing effort of creating a target plasma with tangled magnetic fields as a novel fusion fuel for magneto-inertial fusion (MIF), our current results could shed light on future possible paths of forming such a target for MIF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2016

Emerging single-phase state in small manganite nanodisks

In complex oxides systems such as manganites, electronic phase separation (EPS), a consequence of strong electronic correlations, dictates the exotic electrical and magnetic properties of these materials. A fundamental yet unresolved issue is how EPS responds to spatial confinement; will EPS just scale with size of an object, or will the one of the phases be pinned? Understanding this behavior is critical for future oxides electronics and spintronics because scaling down of the system is unavoidable for these applications. In this work, we use La 0.325 Pr 0.3 Ca 0.375 MnO 3 (LPCMO) single crystalline disks to study the effect of spatial confinement on EPS. The EPS state featuring coexistence of ferromagnetic metallic and charge order insulating phases appears to be the low-temperature ground state in bulk, thin films, and large disks, a previously unidentified ground state (i.e., a single ferromagnetic phase state emerges in smaller disks). The critical size is between 500 nm and 800 nm, which is similar to the characteristic length scale of EPS in the LPCMO system. The ability to create a pure ferromagnetic phase in manganite nanodisks is highly desirable for spintronic applications.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Stochastic and a posteriori optimization to mitigate coil manufacturing errors in stellarator design

Abstract It was recently shown in Wechsung et al (2022 Proc. Natl Acad. Sci. USA 119 e2202084119) that there exist electromagnetic coils that generate magnetic fields, which are excellent approximations to quasi-symmetric fields and have very good particle confinement properties. Using a Gaussian process-based model for coil perturbations, we investigate the impact of manufacturing errors on the performance of these coils. We show that even fairly small errors result in noticeable performance degradation. While stochastic optimization yields minor improvements, it is not possible to mitigate these errors significantly. As an alternative to stochastic optimization, we then formulate a new optimization problem for computing optimal adjustments of the coil positions and currents without changing the shapes of the coil. These a-posteriori adjustments are able to reduce the impact of coil errors by an order of magnitude, providing a new perspective for dealing with manufacturing tolerances in stellarator design.

Physics↗

DOE OSTI2021

Lagrangian particle model for 3D simulation of pellets and SPI fragments in tokamaks

A 3D numerical model for the ablation of pellets and shattered pellet injection (SPI) fragments in tokamaks in the plasma disruption mitigation and fueling parameter space has been developed based on the Lagrangian particle code [R. Samulyak, X. Wang, H.-S. Chen, Lagrangian Particle Method for Compressible Fluid Dynamics, J. Comput. Phys., 362 (2018), 1-19]. The pellet code implements the low magnetic Reynolds number MHD equations, kinetic models for the electronic heating, a pellet surface ablation model, an equation of state that supports multiple ionization states, radiation, and a model for grad-B drift of the ablated material across the magnetic field. The Lagrangian particle algorithm is highly adaptive, capable of simulating a large number of fragments in 3D while eliminating numerical difficulties of dealing with the tokamak background plasma. The code has achieved good agreement with theory for spherically symmetric ablation flows. Axisymmetric simulations of neon and deuterium pellets in magnetic fields ranging from 1 to 6 Tesla have been compared with previous simulations using the FronTier code, and very good agreement has also been obtained. Furthermore, the main physics contribution of the paper is a detailed study of the influence of 3D effects, in particular grad-B drift, on pellet ablation rates and properties of ablation clouds. Smaller reductions of ablation rates in magnetic fields compared to axially symmetric simulations have been demonstrated because the ablated material is not confined to narrowing channels in the presence of grad-B drift. Contribution of various factors in the grad-B drift model has also been quantified.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2015

Aharonov–Anandan quantum phases and Landau quantization associated with a magnetic quadrupole moment

The arising of geometric quantum phases in the wave function of a moving particle possessing a magnetic quadrupole moment is investigated. It is shown that an Aharonov–Anandan quantum phase (Aharonov and Anandan, 1987) can be obtained in the quantum dynamics of a moving particle with a magnetic quadrupole moment. In particular, it is obtained as an analogue of the scalar Aharonov–Bohm effect for a neutral particle (Anandan, 1989). Besides, by confining the quantum particle to a hard-wall confining potential, the dependence of the energy levels on the geometric quantum phase is discussed and, as a consequence, persistent currents can arise from this dependence. Finally, an analogue of the Landau quantization is discussed. -- Highlights: •Scalar Aharonov–Bohm effect for a particle possessing a magnetic quadrupole moment. •Aharonov–Anandan quantum phase for a particle with a magnetic quadrupole moment. •Dependence of the energy levels on the Aharonov–Anandan quantum phase. •Landau quantization associated with a particle possessing a magnetic quadrupole moment.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2025

Magnetically and optically active edges in phosphorene nanoribbons

Abstract Nanoribbons, nanometre-wide strips of a two-dimensional material, are a unique system in condensed matter. They combine the exotic electronic structures of low-dimensional materials with an enhanced number of exposed edges, where phenomena including ultralong spin coherence times 1,2 , quantum confinement 3 and topologically protected states 4,5 can emerge. An exciting prospect for this material concept is the potential for both a tunable semiconducting electronic structure and magnetism along the nanoribbon edge, a key property for spin-based electronics such as (low-energy) non-volatile transistors 6 . Here we report the magnetic and semiconducting properties of phosphorene nanoribbons (PNRs). We demonstrate that at room temperature, films of PNRs show macroscopic magnetic properties arising from their edge, with internal fields of roughly 240 to 850 mT. In solution, a giant magnetic anisotropy enables the alignment of PNRs at sub-1-T fields. By leveraging this alignment effect, we discover that on photoexcitation, energy is rapidly funnelled to a state that is localized to the magnetic edge and coupled to a symmetry-forbidden edge phonon mode. Our results establish PNRs as a fascinating system for studying the interplay between magnetism and semiconducting ground states at room temperature and provide a stepping-stone towards using low-dimensional nanomaterials in quantum electronics.

Science & Technology - Other Topics↗

DOE OSTI2016

Electric field controlled spin interference in a system with Rashba spin-orbit coupling

There have been intense research efforts over the last years focused on understanding the Rashba spin-orbit coupling effect from the perspective of possible spintronics applications. An important component of this line of research is aimed at control and manipulation of electron’s spin degrees of freedom in semiconductor quantum dot devices. A promising way to achieve this goal is to make use of the tunable Rashba effect that relies on the spin-orbit interaction in a two-dimensional electron system embedded in a host semiconducting material that lacks inversion-symmetry. This way, the Rashba spin-orbit coupling effect may potentially lead to fabrication of a new generation of spintronic devices where control of spin, thus magnetic properties, is achieved via an electric field and not a magnetic field. In this work we investigate theoretically the electron’s spin interference and accumulation process in a Rashba spin-orbit coupled system consisting of a pair of two-dimensional semiconductor quantum dots connected to each other via two conducting semi-circular channels. The strength of the confinement energy on the quantum dots is tuned by gate potentials that allow “leakage” of electrons from one dot to another. While going through the conducting channels, the electrons are spin-orbit coupled to a microscopically generated electric field applied perpendicular to the two-dimensional system. We show that interference of spin wave functions of electrons travelling through the two channels gives rise to interference/conductance patterns that lead to the observation of the geometric Berry’s phase. Achieving a predictable and measurable observation of Berry’s phase allows one to control the spin dynamics of the electrons. It is demonstrated that this system allows use of a microscopically generated electric field to control Berry’s phase, thus, enables one to tune the spin-dependent interference pattern and spintronic properties with no need for injection of spin-polarized electrons.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2015

The high-β{sub N} hybrid scenario for ITER and FNSF steady-state missions

New experiments on DIII-D have demonstrated the steady-state potential of the hybrid scenario, with 1 MA of plasma current driven fully non-inductively and β{sub N} up to 3.7 sustained for ∼3 s (∼1.5 current diffusion time, τ{sub R}, in DIII-D), providing the basis for an attractive option for steady-state operation in ITER and FNSF. Excellent confinement is achieved (H{sub 98y2} ∼ 1.6) without performance limiting tearing modes. The hybrid regime overcomes the need for off-axis current drive efficiency, taking advantage of poloidal magnetic flux pumping that is believed to be the result of a saturated 3/2 tearing mode. This allows for efficient current drive close to the axis, without deleterious sawtooth instabilities. In these experiments, the edge surface loop voltage is driven down to zero for >1 τ{sub R} when the poloidal β is increased above 1.9 at a plasma current of 1.0 MA and the ECH power is increased to 3.2 MW. Stationary operation of hybrid plasmas with all on-axis current drive is sustained at pressures slightly above the ideal no-wall limit, while the calculated ideal with-wall MHD limit is β{sub N} ∼ 4–4.5. Off-axis Neutral Beam Injection (NBI) power has been used to broaden the pressure and current profiles in this scenario, seeking to take advantage of higher predicted kink stability limits and lower values of the tearing stability index Δ′, as calculated by the DCON and PEST3 codes. Results based on measured profiles predict ideal limits at β{sub N} > 4.5, 10% higher than the cases with on-axis NBI. A 0-D model, based on the present confinement, β{sub N} and shape values of the DIII-D hybrid scenario, shows that these plasmas are consistent with the ITER 9 MA, Q = 5 mission and the FNSF 6.7 MA scenario with Q = 3.5. With collisionality and edge safety factor values comparable to those envisioned for ITER and FNSF, the high-β{sub N} hybrid represents an attractive high performance option for the steady-state missions of these devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗