Search NASA⌕ Search

SEARCH · Search NASA

Results for “Numerical approximation & analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

On the Rates of Coronal Mass Ejections: Remote Solar and In Situ Observations

We compare the rates of coronal mass ejections (CMEs) as inferred from remote solar observations and interplanetary CMEs (ICMEs) as inferred from in situ observations at both 1 AU and Ulyssses from 1996 through 2004. We also distinguish between those ICMEs that contain a magnetic cloud (MC) and those that do not. While the rates of CMEs and ICMEs track each other well at solar minimum, they diverge significantly in early 1998, during the ascending phase of the solar cycle, with the remote solar observations yielding approximately 20 times more events than are seen at 1 AU. This divergence persists through 2004. A similar divergence occurs between MCs and non-MC ICMEs. We argue that these divergences are due to the birth of midlatitude active regions, which are the sites of a distinct population of CMEs, only partially intercepted by Earth, and we present a simple geometric argument showing that the CME and ICME rates are consistent with one another. We also acknowledge contributions from (1) an increased rate of high-latitude CMEs and (2) focusing effects from the global solar field. While our analysis, coupled with numerical modeling results, generally supports the interpretation that whether one observes a MC within an ICME is sensitive to the trajectory of the spacecraft through the ICME (i.e., an observational selection effect), one result directly contradicts it. Specifically, we find no systematic offset between the latitudinal origin of ICMEs that contain MCs at 1 AU in the ecliptic plane and that of those that do not.

Riley, Pete↗

Hypersonic Boundary-Layer Transition over a Blunt Circular Cone in a Mach 8 Digital Wind Tunnel

To understand the effects of freestream acoustic disturbances on transition reversal over a blunt body, three-dimensional direct numerical simulations (DNS) were conducted to investigate the interaction of a tunnel-like acoustic disturbance field with a Mach 8 laminar boundary layer over a 7 deg half-angle blunt cone with a nose radius of 𝑅 𝑛 = 5.2 mm. The flow conditions and the axisymmetric cone geometry matched those measured in the Sandia Hypersonic Wind Tunnel at Mach 8 (Sandia HWT-8), and the incident freestream acoustic disturbances in the DNS were generated by acoustic radiation from the nozzle-wall turbulent boundary layer in the same tunnel. Consistent with the predictions of the nonmodal instability analysis, the study shows the emergence of a second spectral peak for moderately oblique waves between 150 kHz and 200 kHz in the aft part of the cone. The spectral energy of temperature and streamwise velocity fluctuations is initially concentrated within the entropy layer. These fluctiations are eventually “swallowed” by the boundary layer as the entropy-layer thickness 𝛿 𝑆 becomes similar to the boundary-layer thickness 𝛿h𝑡 at downstream locations. The numerical schlieren contours show the same inclined structures commonly observed in blunt cone experiments, and these structures are found to be three dimensional and advect with a constant speed approximately equal to the mean flow speed near the edge of the boundary layer.

Hypersonic Flow↗

Hypersonic Boundary-Layer Transition over a Blunt Circular Cone in a Mach 8 Digital Wind Tunnel

To understand the effects of freestream acoustic disturbances on transition reversal over a blunt body, three-dimensional direct numerical simulations (DNS) were conducted to investigate the interaction of a tunnel-like acoustic disturbance field with a Mach 8 laminar boundary layer over a 7 deg half-angle blunt cone with a nose radius of 𝑅 𝑛 = 5.2 mm. The flow conditions and the axisymmetric cone geometry matched those measured in the Sandia Hypersonic Wind Tunnel at Mach 8 (Sandia HWT-8), and the incident freestream acoustic disturbances in the DNS were generated by acoustic radiation from the nozzle-wall turbulent boundary layer in the same tunnel. Consistent with the predictions of the nonmodal instability analysis, the study shows the emergence of a second spectral peak for moderately oblique waves between 150 kHz and 200 kHz in the aft part of the cone. The spectral energy of temperature and streamwise velocity fluctuations is initially concentrated within the entropy layer. These fluctiations are eventually “swallowed” by the boundary layer as the entropy-layer thickness 𝛿 𝑆 becomes similar to the boundary-layer thickness 𝛿h𝑡 at downstream locations. The numerical schlieren contours show the same inclined structures commonly observed in blunt cone experiments, and these structures are found to be three dimensional and advect with a constant speed approximately equal to the mean flow speed near the edge of the boundary layer.

Hypersonic Flow↗

Filament Wound Composite Analysis Using the NASA Multiscale Analysis Tool (NASMAT) and Finite Element Analysis

Fiber reinforced composite materials, owing to their tailorable thermomechanical and functional properties, allow one to produce a structure that is stronger, stiffer, and lighter than its metal counterpart while performing the same function, yielding a more efficient structure. This not only allows for the improvement of current technologies like aircraft structures, but also enables new technologies like gaseous hydrogen storage for mobility applications, which are otherwise impractical when manufactured using traditional metals due to weight and space restrictions or material embrittlement. However, the use of composites imposes greater design and manufacturing challenges on an engineer, since they are heterogenous, having a distinct structure across multiple length scale, behave generally anisotropically at the structural level and require complex manufacturing and processing methods. Capturing this complex behavior requires detailed numerical simulations, including the modeling of microstructural features like undulations, voids, and fiber alignment. In this paper, multiple repeating unit cells (RUCs), representing filament wound composites, are developed (via a script provided in the Appendix) and analyzed. The refinement of these RUCs is varied, and the analyses are performed using both the Abaqus finite element software and the NASA Multiscale Analysis Tool (NASMAT). A study is undertaken to compare the predicted effective elastic properties of the wound RUC to a laminate representation of the wound RUC, which neglects the undulations. Additionally, two different sets of periodic boundary conditions (PBCs) have been examined. One approximates the real boundary conditions using a standard approach and the other represents the PBCs exactly through the use of an offset. Lastly, a comparison of the local elastic stress fields is made among the models and approaches. Since wound structures are often approximated as laminated structures, it is important to understand the degree to which this assumption is valid, namely by first comparing the elastic constants and local elastic fields. This will provide, on the one hand, information concerning the bulk mechanical behavior and, on the other hand, insights concerning local load distributions and likely damage initiation sites.

Composites↗

An extended/generalized phase-field finite element method for crack growth with global-local enrichment

In this paper, an extended/generalized finite element method (XFEM/GFEM) for simulating quasistatic crack growth based on a phase-field method is presented. The method relies on approximations to solutions associated with two different scales: a global scale, that is, structural and discretized with a coarse mesh, and a local scale encapsulating the fractured region, that is, discretized with a fine mesh. A stable XFEM/GFEM is employed to embed the displacement and damage fields at the global scale. The proposed method accommodates approximation spaces that evolve between load steps, while preserving a fixed background mesh for the structural problem. In addition, a prediction-correction algorithm is employed to facilitate the dynamic evolution of the confined crack regions within a load step. Several numerical examples of benchmark problems in two- and three-dimensional quasistatic fracture are provided to demonstrate the approach.

multiscale↗

Mind the Gap: Addressing Data Gaps and Assessing Noise Mismodeling in LISA

Due to the sheer complexity of the Laser Interferometer Space Antenna (LISA) space mission, data gaps arising from instrumental irregularities and/or scheduled maintenance are unavoidable. Focusing on merger-dominated massive black hole binary signals, we test the appropriateness of the Whittle-likelihood on gapped data in a variety of cases. From first principles, we derive the likelihood valid for gapped data in both the time and frequency domains. Cheap-to-evaluate proxies to p-p plots are derived based on a Fisher-based formalism, and verified through Bayesian techniques. Our tools allow to predict the altered variance in the parameter estimates that arises from noise mismodeling, as well as the information loss represented by the broadening of the posteriors. The result of noise mismodeling with gaps is sensitive to the characteristics of the noise model, with strong low-frequency (red) noise and strong high-frequency (blue) noise giving statistically significant fluctuations in recovered parameters. We demonstrate that the introduction of a tapering window reduces statistical inconsistency errors, at the cost of less precise parameter estimates. We also show that the assumption of independence between inter-gap segments appears to be a fair approximation even if the data set is inherently coherent. However, if one instead assumes fictitious correlations in the data stream, when the data segments are actually independent, then the resultant parameter recoveries could be inconsistent with the true parameters. The theoretical and numerical practices that are presented in this work could readily be incorporated into global-fit pipelines operating on gapped data.

LISA↗

Fluctuations in strongly coupled cosmologies

In the early Universe, a dual component made of coupled CDM and a scalar field Φ, if their coupling β > (3){sup 1/2}/2, owns an attractor solution, making them a stationary fraction of cosmic energy during the radiation dominated era. Along the attractor, both such components expand ∝a{sup −4} and have early density parameters Ω{sub d} = 1/(4β{sup 2}) and Ω{sub c} = 2 Ω{sub d} (field and CDM, respectively). In a previous paper it was shown that, if a further component, expanding ∝a{sup −3}, breaks such stationary expansion at z ∼ 3–5 × 10{sup 3}, cosmic components gradually acquire densities consistent with observations. This paper, first of all, considers the case that this component is warm. However, its main topic is the analysis of fluctuation evolution: out of horizon modes are then determined; their entry into horizon is numerically evaluated as well as the dependence of Meszaros effect on the coupling β; finally, we compute: (i) transfer function and linear spectral function; (ii) CMB C{sub l} spectra. Both are close to standard ΛCDM models; in particular, the former one can be so down to a scale smaller than Milky Way, in spite of its main DM component being made of particles of mass < 1 keV. The previously coupled CDM component, whose present density parameter is O(10{sup −3}), exhibits wider fluctuations δρ/ρ, but approximately β-independent δρ values. We discuss how lower scale features of these cosmologies might ease quite a few problems that ΛCDM does not easily solve.

79 ASTRONOMY AND ASTROPHYSICS↗

On the relationship between acoustic energy density flux near the jet axis and far field acoustic intensity

By measurement and analysis, the relationship between the distribution of the outflow of acoustic energy over the jet boundary and the far-field intensity is considered. The physical quantity used is the gradient of the pressure evaluated on a geometrical plane at the smallest possible radial distance from the jet axis, but outside the vortical region, in the area where the homogeneous wave equation is reasonably well satisfied. The numerical and experimental procedures involved have been checked out by using a known source. Results indicate that the acoustic power output per unit length of the jet, in the region from which the sound emanates, peaks at approximately 9 diameters downstream. The acoustic emission for a jet Strouhal number of about 0.3 exceeds the emission for all other Strouhal numbers nearly everywhere along the measurement plane. However, the far-field peak intensity distribution obtained from the contribution of each station was found to depend on the spatial extent of the region where sound emanates from the jet, which, in turn, depends more on the far-field angle than on the Strouhal number.

Maestrello, L.↗

Multi-Scale Modeling of Low-Density Carbon-Phenolic Ablators

Protecting a spacecraft during atmospheric entry is one of highest risk factors that needs to be mitigated during design of a space exploration mission. At entry speeds from space, air turns into high-temperature plasma, and spacecraft Thermal Protection Systems (TPS) are needed to protect the vehicle payload. Modern successful material architectures of spacecraft shields use a porous carbon fiber substrate impregnated with phenolic as an ablator material. In the lecture, efforts to build a Predictive Material Modeling framework for porous ablators from micro-scale to macro-scale will be presented. Several numerical methods and techniques will be summarized that use voxelized images to compute geometrical properties of the porous substrate. These computed properties include porosity, specific surface area and tortuosity that are otherwise indirectly measured through experimental techniques. Direct simulation Monte Carlo (DSMC), a particle-based method for approximating the Boltzmann equation, is used to compute the permeability coefficient of the porous substrate based on its digitized representation. The method computes the flow within the microstructure, where the size of the pores may approach the mean-free-path of the flow. Finally, a high-fidelity model implemented in PATO (Porous-material Analysis Toolbox) is discussed, and some examples of ablative material response are presented, including for the first time 3D simulations of the full tiled heat shield for the Mars Science Laboratory (MSL) capsule.

Ablators↗

Analysis of thermo-elastic problems using the improved element-free Galerkin method

The improved element-free Galerkin method (IEFG) is presented to deal with thermo-elastic problems. This mesh-free method is a combination between the element-free Galerkin method and the improved moving least-square approximation. It has not the Kronecker delta property, and the penalty method is used to impose the essential boundary conditions. In this paper, linear and stationary thermo-elasticity is treated. To solve the thermo-elastic problem, this latter is decoupled into two separate parts: first, the heat transfer problem is analyzed to reach the temperature field, which is used as input in the mechanical problem to calculate the displacement field and then the stress fields. Numerical examples with different boundary conditions are illustrated. The performance and the accuracy of the IEFG method are approved when obtained results are compared to finite-element results and analytical solution.

97 MATHEMATICS AND COMPUTING↗

Spectral analysis of the efficiency of vertical mixing in the deep ocean due to interaction of tidal currents with a ridge running down a continental slope

Efficiency of mixing, resulting from the reflection of an internal wave field imposed on the oscillatory background flow with a three-dimensional bottom topography, is investigated using a linear approximation. The radiating wave field is associated with the spectrum of the linear model, which consists of those mode numbers n and slope values α, for which the solution represents the internal waves of frequencies ω = nω0 radiating upwrad of the topography, where ω0 is the fundamental frequency at which internal waves are generated at the topography. The effects of the bottom topography and the earth’s rotation on the spectrum is analyzed analytically and numerically in the vicinity of the critical slope, which is a slope with the same angle to the horizontal as the internal wave characteristic. In this notation, θ is latitude, f is the Coriolis parameter and N is the buoyancy frequency, which is assumed to be a constant, which corresponds to the uniform stratification.

Ibragimov, Ranis N.↗

Thermoviscoplastic analysis of fibrous periodic composites by the use of triangular subvolumes

The non-linear viscoplastic behavior of fibrous periodic composites is analyzed by discretizing the unit cell into triangular subvolumes. A set of these subvolumes can be configured by the analyst to construct a representation for the unit cell of a periodic composite. In each step of the loading history the total strain increment at any point is governed by an integral equation which applies to the entire composite. A Fourier series approximation allows the incremental stresses and strains to be determined within a unit cell of the periodic lattice. The non-linearity arising from the viscoplastic behavior of the constituent materials comprising the composite is treated as a fictitious body force in the governing integral equation. Specific numerical examples showing the stress distributions in the unit cell of a fibrous tungsten/copper metal-matrix composite under viscoplastic loading conditions are given. The stress distribution resulting in the unit cell when the composite material is subjected to an overall transverse stress loading history perpendicular to the fibers is found to be highly heterogeneous, and typical homogenization techniques based on treating the stress and strain distributions within the constituent phases as homogeneous result in large errors under inelastic loading conditions.

Walker, Kevin P.↗

Fracture Analysis of Semi-Elliptical Surface Cracks in Ductile Materials

Accurate life assessment of structural components may require advanced life prediction criteria and methodologies. Structural components often exhibit several different types of defects, among the most prevalent being surface cracks. A semi-elliptical surface crack subjected to monotonic loading will exhibit stable crack growth until the crack has reached a critical size, at which the crack loses stability and fracture ensues (Newman, 2000). The shape and geometry of the flaw are among the most influential factors. When considering simpler crack configurations, such as a through-the-thickness crack, a three-dimensional (3D) geometry may be modeled under the approximation of two-dimensional (2D) plane stress or plane strain. The more complex surface crack is typically modeled numerically with the Finite Element Method (FEM). A semi-elliptical surface crack is illustrated in Figure 1-1.

Daniewicz, S. R.↗

Enhancement of lanthanide evaporation by complexation: Dysprosium tri-iodide mixed with indium iodide and thulium tri-iodide mixed with thallium iodide

The vapors in equilibrium with condensates of DyI{sub 3}, DyI{sub 3}/InI, TmI{sub 3}, and TmI{sub 3}/TlI were observed over the temperature range from 900 K to 1400 K using x-ray induced fluorescence. The total densities of each element (Dy, Tm, In, Tl, and I) in the vapor, summed over all atomic and molecular species, were determined. Dramatic enhancements in the total vapor densities of Dy and Tm were observed in the vapors over DyI{sub 3}/InI and TmI{sub 3}/TlI as compared to the vapors over pure DyI{sub 3} and pure TmI{sub 3}, respectively. An enhancement factor exceeding 10 was observed for Dy at T≈ 1020 K, decreasing to 0 at T≈ 1250 K. An enhancement factor exceeding 20 was observed for Tm at T≈ 1040 K, decreasing to 0 at T≈ 1300 K. Such enhancements are expected from the formation of the vapor-phase hetero-complexes DyInI{sub 4} and TmTlI{sub 4}. Numerical simulations of the thermo-chemical equilibrium suggest the importance of additional complexes in liquid phases. A description of the measurement technique is given. Improvements in the absolute calibration lead to an approximately 40% correction to previously reported preliminary results [J. J. Curry et al., Chem. Phys. Lett. 507, 52 (2011); Appl. Phys. Lett. 100, 083505 (2012)].

36 MATERIALS SCIENCE↗

Sonic boom analysis for high-altitude flight at high Mach number

Numerical programs for the computation of the flow field from the airplane at the flight altitude to the ground are presented. They take into account the nonlinear effects of high Mach number, the entropy change across the shock, the entropy and enthalpy variations in the atmospheric layer, and the gravitational effect. Extension of the programs for the axisymmetric problems to handle nonaxisymmetric terms is described. The asymmetry can be caused by the geometry of the body and the lift, and also by the fact that the variations in the atmospheric layer are two-dimensional. Numerical results for ground level signatures of several configurations at various flight conditions are presented and compared with existing approximate theories to demonstrate the influences of these nonlinear effects.

Ferri, A.↗

Solution verification, goal-oriented adaptive methods for stochastic advection–diffusion problems

A goal-oriented analysis of linear, stochastic advection–diffusion models is presented which provides both a method for solution verification as well as a basis for improving results through adaptation of both the mesh and the way random variables are approximated. A class of model problems with random coefficients and source terms is cast in a variational setting. Specific quantities of interest are specified which are also random variables. A stochastic adjoint problem associated with the quantities of interest is formulated and a posteriori error estimates are derived. These are used to guide an adaptive algorithm which adjusts the sparse probabilistic grid so as to control the approximation error. Numerical examples are given to demonstrate the methodology for a specific model problem.

97 MATHEMATICS AND COMPUTING↗

System noise analysis of the dumbbell tethered satellite for gravity-gradient measurements

An analysis of the dumbbell gravity gradiometer concept for measuring short wavelength variations in the earth's gravity gradient is presented. Variations in the gradient are recorded by measuring tension variations in a vertically stabilized satellite consisting of heavy masses connected by a long wire or rod. Tension noise arises from the excitation of various mechanical oscillations of the system. The principal noise sources that were identified are fluctuations in atmospheric drag heating and drag force resulting from density variations and winds. Approximate analytical expressions are presented for the tension noise as a function of the system design parameters for various possible configurations. Computer simulations using numerical integration were performed to study the tension noise for several sample cases. Three designs consistent with Shuttle launch capabilities are discussed.

Colombo, G.↗

Analysis of the fluid flow and heat transfer in a thin liquid film in the presence and absence of gravity

The hydrodynamic and thermal behavior of a thin liquid film flowing over a solid horizontal surface is analyzed for both plane and radially spreading flows. The situations where the gravitational force is completely absent and where it is significant are analyzed separately and their practical relevance to a micro-gravity environment is discussed. In the presence of gravity, in addition to Reynolds number, the Froude number of the film is found to be an important parameter that determines the supercritical and subcritical flow regimes and any associated hydraulic jump. A closed-form solution is possible under some flow situations, whereas others require numerical integration of ordinary differential equations. The approximate analytical results are found to compare well with the available two-dimensional numerical solutions.

Rahman, M. M.↗