Search NASA⌕ Search

SEARCH · Search NASA

Results for “Operating Mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Decarbonization of the Electric Power Sector and Implications for Low-Cost Hydrogen Production from Water Electrolysis

Increasing development of wind and solar generation in the power sector can create economic opportunities for the deployment of water electrolyzers that produce hydrogen. Temporal variation in the marginal cost of energy in future decarbonized grids can make it favorable for electrolyzers to dispatchably ramp hydrogen production up and down in response to low- and high-cost times. Using this strategy, low-cost hydrogen production is enabled by electrolyzers that are low-capital cost and tolerant to frequent on/off cycling. Ramping down hydrogen production to a designated turndown ratio can avoid performance degradation caused by on/off cycling by not shutting the electrolyzer completely off. This comes with a slight cost penalty which can be minimized if the turndown ratio is low (i.e., the system ramps down hydrogen production to close to zero). These results suggest that electrolyzers integrated into future power systems are likely to benefit from the ability to ramp operation up and down quickly and operate in a standby mode. This analysis forms a basis for comparative tradeoffs between electrolyzer capital cost, operating strategy, and system durability and demonstrates the importance of considering all three factors in technoeconomic analysis.

capital cost↗

Experiments and theory on parametric instabilities excited in HF heating experiments at HAARP

Parametric instabilities excited by O-mode HF heater and the induced ionospheric modification were explored via HAARP digisonde operated in a fast mode. The impact of excited Langmuir waves and upper hybrid waves on the ionosphere are manifested by bumps in the virtual spread, which expand the ionogram echoes upward as much as 140 km and the downward range spread of the sounding echoes, which exceeds 50 km over a significant frequency range. The theory of parametric instabilities is presented. The theory identifies the ionogram bump located between the 3.2 MHz heater frequency and the upper hybrid resonance frequency and the bump below the upper hybrid resonance frequency to be associated with the Langmuir and upper hybrid instabilities, respectively. The Langmuir bump is located close to the upper hybrid resonance frequency, rather than to the heater frequency, consistent with the theory. Each bump in the virtual height spread of the ionogram is similar to the cusp occurring in daytime ionograms at the E-F2 layer transition, indicating that there is a small ledge in the density profile similar to E-F2 layer transitions. The experimental results also show that the strong impact of the upper hybrid instability on the ionosphere can suppress the Langmuir instability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Grassmann phase space theory and the Jaynes–Cummings model

The Jaynes–Cummings model of a two-level atom in a single mode cavity is of fundamental importance both in quantum optics and in quantum physics generally, involving the interaction of two simple quantum systems—one fermionic system (the TLA), the other bosonic (the cavity mode). Depending on the initial conditions a variety of interesting effects occur, ranging from ongoing oscillations of the atomic population difference at the Rabi frequency when the atom is excited and the cavity is in an n-photon Fock state, to collapses and revivals of these oscillations starting with the atom unexcited and the cavity mode in a coherent state. The observation of revivals for Rydberg atoms in a high-Q microwave cavity is key experimental evidence for quantisation of the EM field. Theoretical treatments of the Jaynes–Cummings model based on expanding the state vector in terms of products of atomic and n-photon states and deriving coupled equations for the amplitudes are a well-known and simple method for determining the effects. In quantum optics however, the behaviour of the bosonic quantum EM field is often treated using phase space methods, where the bosonic mode annihilation and creation operators are represented by c-number phase space variables, with the density operator represented by a distribution function of these variables. Fokker–Planck equations for the distribution function are obtained, and either used directly to determine quantities of experimental interest or used to develop c-number Langevin equations for stochastic versions of the phase space variables from which experimental quantities are obtained as stochastic averages. Phase space methods have also been developed to include atomic systems, with the atomic spin operators being represented by c-number phase space variables, and distribution functions involving these variables and those for any bosonic modes being shown to satisfy Fokker–Planck equations from which c-number Langevin equations are often developed. However, atomic spin operators satisfy the standard angular momentum commutation rules rather than the commutation rules for bosonic annihilation and creation operators, and are in fact second order combinations of fermionic annihilation and creation operators. Though phase space methods in which the fermionic operators are represented directly by c-number phase space variables have not been successful, the anti-commutation rules for these operators suggest the possibility of using Grassmann variables—which have similar anti-commutation properties. However, in spite of the seminal work by Cahill and Glauber and a few applications, the use of phase space methods in quantum optics to treat fermionic systems by representing fermionic annihilation and creation operators directly by Grassmann phase space variables is rather rare. This paper shows that phase space methods using a positive P type distribution function involving both c-number variables (for the cavity mode) and Grassmann variables (for the TLA) can be used to treat the Jaynes–Cummings model. Although it is a Grassmann function, the distribution function is equivalent to six c-number functions of the two bosonic variables. Experimental quantities are given as bosonic phase space integrals involving the six functions. A Fokker–Planck equation involving both left and right Grassmann differentiations can be obtained for the distribution function, and is equivalent to six coupled equations for the six c-number functions. The approach used involves choosing the canonical form of the (non-unique) positive P distribution function, in which the correspondence rules for the bosonic operators are non-standard and hence the Fokker–Planck equation is also unusual. Initial conditions, such as those above for initially uncorrelated states, are discussed and used to determine the initial distribution function. Transformations to new bosonic variables rotating at the cavity frequency enable the six coupled equations for the new c-number functions–that are also equivalent to the canonical Grassmann distribution function–to be solved analytically, based on an ansatz from an earlier paper by Stenholm. It is then shown that the distribution function is exactly the same as that determined from the well-known solution based on coupled amplitude equations. In quantum–atom optics theories for many atom bosonic and fermionic systems are needed. With large atom numbers, treatments must often take into account many quantum modes—especially for fermions. Generalisations of phase space distribution functions of phase space variables for a few modes to phase space distribution functionals of field functions (which represent the field operators, c-number fields for bosons, Grassmann fields for fermions) are now being developed for large systems. For the fermionic case, the treatment of the simple two mode problem represented by the Jaynes–Cummings model is a useful test case for the future development of phase space Grassmann distribution functional methods for fermionic applications in quantum–atom optics. -- Highlights: •Novel phase space theory of the Jaynes–Cummings model using Grassmann variables. •Fokker–Planck equations solved analytically. •Results agree with the standard quantum optics treatment. •Grassmann phase space theory applicable to fermion many-body problems.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Real-time atomic-resolution imaging of crystal growth process in water by phase modulation atomic force microscopy at one frame per second

Recent advancement in dynamic-mode atomic force microscopy (AFM) has enabled its operation in liquid with atomic-scale resolution. However, its imaging speed has often been too slow to visualize atomic-scale dynamic processes. Here, we propose a method for making a significant improvement in the operation speed of dynamic-mode AFM. In this method, we use a wideband and low-latency phase detector with an improved algorithm for the signal complexification. We demonstrate atomic-scale imaging of a calcite crystal growth process in water at one frame per second. The significant improvement in the imaging speed should enable various studies on unexplored atomic-scale interfacial processes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Load-cell based characterization system for a “Violin-Mode” shadow-sensor in advanced LIGO suspensions

The background to this work was a prototype shadow sensor, which was designed for retro-fitting to an advanced LIGO (Laser Interferometer Gravitational wave Observatory) test-mass/mirror suspension, in which 40 kg test-mass/mirrors are each suspended by four approximately 600 mm long by 0.4 mm diameter fused-silica suspension fibres. The shadow sensor comprised a LED source of Near InfraRed (NIR) radiation and a rectangular silicon photodiode detector, which, together, were to bracket the fibre under test. The aim was to detect transverse Violin-Mode resonances in the suspension fibres. Part of the testing procedure involved tensioning a silica fibre sample and translating it transversely through the illuminating NIR beam, so as to measure the DC responsivity of the detection system to fibre displacement. However, an equally important part of the procedure, reported here, was to keep the fibre under test stationary within the beam, whilst trying to detect low-level AC Violin-Mode resonances excited on the fibre, in order to confirm the primary function of the sensor. Therefore, a tensioning system, incorporating a load-cell readout, was built into the test fibre’s holder. The fibre then was excited by a signal generator, audio power amplifier, and distant loudspeaker, and clear resonances were detected. A theory for the expected fundamental resonant frequency as a function of fibre tension was developed and is reported here, and this theory was found to match closely with the detected resonant frequencies as they varied with tension. Consequently, the resonances seen were identified as being proper Violin-Mode fundamental resonances of the fibre, and the operation of the Violin-Mode detection system was validated.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Quantum random number generator

A quantum random number generator (QRNG) and a photon generator for a QRNG are provided. The photon generator may be operated in a spontaneous mode below a lasing threshold to emit photons. Photons emitted from the photon generator may have at least one random characteristic, which may be monitored by the QRNG to generate a random number. In one embodiment, the photon generator may include a photon emitter and an amplifier coupled to the photon emitter. The amplifier may enable the photon generator to be used in the QRNG without introducing significant bias in the random number and may enable multiplexing of multiple random numbers. The amplifier may also desensitize the photon generator to fluctuations in power supplied thereto while operating in the spontaneous mode. In one embodiment, the photon emitter and amplifier may be a tapered diode amplifier.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Quasilinear modelling of collisional trapped electron modes

The simplification of collision operators is necessary for quasilinear turbulence modelling used with integrated modelling frameworks, such as the gyrokinetic code QuaLiKiz. The treatment of collisions greatly impacts the accuracy of trapped electron mode (TEM) modelling, which is necessary to predict the electron heat flux and the balance between inward and outward particle fluxes. In particular, accurate particle flux predictions are necessary to successfully model density peaking in the tokamak core. We explored two ways of improving collisional TEM model reduction for tokamak core plasmas. First, we carried out linear GENE simulations to study the complex interplay between collisions and trapped electrons. We then used these simulations to define an effective trapped fraction to characterize the collisional TEM based on two key parameters, the local inverse-aspect ratio $\epsilon$ and the collisionality $\nu ^\ast$. One aspect missing from analytical TEM research is that the collisional frequency and the bounce-transit frequency are both velocity dependent; this effective trapped fraction takes both into account. In doing so, we determined that two parameters are not enough to model the collisional TEM, as an additional third free parameter was necessary. We determined that this model, as currently formulated, is not suitable for integrated modelling purposes. Second, we directly improved QuaLiKiz's Krook operator, which relies on two free parameters. We determined that these parameters required adjustments against higher-fidelity collisional models. In order to improve density profile predictions when paired with integrated models, we refined the Krook operator by using GENE simulations as a higher-fidelity point of comparison. We then demonstrate strong improvement of density peaking predictions of QuaLiKiz within the integrated modelling framework JETTO.

fusion plasma↗

Coordinated operation of pumped-storage hydropower with power and water distribution systems

Small pumped-storage hydropower (PSH) units have gained popularity as distributed energy storage options that can provide flexibility to the operation of power distribution systems. Optimal operation of small PSH units is not only dependent on the energy storage provided to power distribution system, but also on the inflow and outflow of water from and to the water distribution system. Here, in this context, this paper develops an optimization model for coordinated operation of PSH units with power and water distribution systems. The proposed model optimizes the operation of water tanks, variable-speed pumps and PSH in pumping and generating modes to minimize the operation cost of power distribution system, while respecting the power flow constraints of power distribution and hydraulic constraints of water distribution system. Appropriate electricity tariffs are implemented to avoid additional expenses in water distribution system that can be enforced by its coordinated operation in favor of power distribution system. The proposed model is implemented on a 33-bus and a 123-bus test power distribution system connected to a 16-node test water distribution system. Results demonstrate the effectiveness of proposed model in tapping PSH flexibility to reduce the operation cost of power and water distribution systems, while meeting the power and water demands.

13 HYDRO ENERGY↗

Propagation And Damping Of High Harmonic Fast Waves And Electron Cyclotron Waves In The Nstx-U-Device

For the spherical torus and for conventional tokamaks to be viable means of producing fusion energy there are two important requirements. The first is to heat the plasma in the experimental devices to high temperatures; preferably, to fusion relevant temperatures. The second is to drive a current in the plasma so that the fusion device operates in a steady-state mode. A pulsed fusion reactor for energy production is not desirable. A favored means to achieve both of these requirements is through the use of microwaves, commonly referred to as radio frequency waves. This proposal was to understand observations from the National Spherical Torus Experiment Upgrade (NSTX-U) device on radio frequency wave heating of the confined plasma during operations with high harmonic fast waves. The proposed research was also directed toward assisting in the optimization of the experimental modes of operation so as to maximize the heating efficiency. A detailed analysis of the experiments has shown that about one-third of the input radio frequency power does not make it into the core region of the plasma where heating is required. The losses are believed to occur primarily in the edge region where the radio frequency power is initially coupled into the plasma. Using sophisticated computational codes and theoretical models, that have been developed for the NSTX-U experimental program, this research quantified the physical processes which occur in the edge plasma and lead to a decrease in the heating efficiency. The effect of edge turbulence on the scattering of radio frequency waves was studied for waves in the ion cyclotron and electron cyclotron range of frequencies. For high harmonic fast waves in the ion cyclotron range of frequencies, simulations were carried out using a full-wave solver that was extended to the vacuum vessel wall. These simulations successfully reproduced trends that were observed experimentally. This simulation capability was also used to study the interaction of high harmonic fast waves with the scrape-off layer plasma. More recently, a new technique has been developed for the calculation of radio frequency waves in toroidal geometry that enables the simultaneous incorporation of antenna geometry, plasma facing components, the scrape off-layer, and core propagation in the high harmonic fast wave regime. The effect of turbulent plasmas on the mode conversion of extraordinary electromagnetic waves in the electron cyclotron range of frequencies in the NSTX-U plasma has been studied theoretically. In the over-dense plasmas of NSTX-U, the traditional electromagnetic waves are not effective for delivering energy and momentum to the core plasma. However, electron Bernstein waves generated by mode conversion are efficient carriers of wave energy and momentum to the core. The mode conversion occurs in the turbulent edge region. A theory for mode conversion in such plasmas has been developed. The parameters that can optimize the mode conversion can be readily determined. Also, the model is useful for experimentalists to analyze observation on a shot-to-shot basis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Propagation And Damping Of High Harmonic Fast Waves And Electron Cyclotron Waves In The Nstx-U-Device

For the spherical torus and for conventional tokamaks to be viable means of producing fusion energy there are two important requirements. The first is to heat the plasma in the experimental devices to high temperatures; preferably, to fusion relevant temperatures. The second is to drive a current in the plasma so that the fusion device operates in a steady-state mode. A pulsed fusion reactor for energy production is not desirable. A favored means to achieve both of these requirements is through the use of microwaves, commonly referred to as radio frequency waves. This proposal was to understand observations from the National Spherical Torus Experiment Upgrade (NSTX-U) device on radio frequency wave heating of the confined plasma during operations with high harmonic fast waves. The proposed research was also directed toward assisting in the optimization of the experimental modes of operation so as to maximize the heating efficiency. A detailed analysis of the experiments has shown that about one-third of the input radio frequency power does not make it into the core region of the plasma where heating is required. The losses are believed to occur primarily in the edge region where the radio frequency power is initially coupled into the plasma. Using sophisticated computational codes and theoretical models, that have been developed for the NSTX-U experimental program, this research quantified the physical processes which occur in the edge plasma and lead to a decrease in the heating efficiency. The effect of edge turbulence on the scattering of radio frequency waves was studied for waves in the ion cyclotron and electron cyclotron range of frequencies. For high harmonic fast waves in the ion cyclotron range of frequencies, simulations were carried out using a full-wave solver that was extended to the vacuum vessel wall. These simulations successfully reproduced trends that were observed experimentally. This simulation capability was also used to study the interaction of high harmonic fast waves with the scrape-off layer plasma. More recently, a new technique has been developed for the calculation of radio frequency waves in toroidal geometry that enables the simultaneous incorporation of antenna geometry, plasma facing components, the scrape off-layer, and core propagation in the high harmonic fast wave regime. The effect of turbulent plasmas on the mode conversion of extraordinary electromagnetic waves in the electron cyclotron range of frequencies in the NSTX-U plasma has been studied theoretically. In the over-dense plasmas of NSTX-U, the traditional electromagnetic waves are not effective for delivering energy and momentum to the core plasma. However, electron Bernstein waves generated by mode conversion are efficient carriers of wave energy and momentum to the core. The mode conversion occurs in the turbulent edge region. A theory for mode conversion in such plasmas has been developed. The parameters that can optimize the mode conversion can be readily determined. Also, the model is useful for experimentalists to analyze observation on a shot-to-shot basis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

CERN’s Linac4 H{sup −} sources: Status and operational results

Two volume sources equipped with DESY and CERN plasma generators and a low voltage electron dump were operated at 45 kV in the Linac4 tunnel and on a dedicated test stand. These volume sources delivered approximately 20 mA and ensured the commissioning of the Radio Frequency Quadrupole accelerator and of the first section of the Drift Tube Linac. CERN’s prototype of a cesiated surface source equipped with this electron dump was operated continuously from November 2013 to April 2014 on the ion source test stand and is being commissioned in the Linac4 tunnel. Before cesiation, the prototype conditioned in volume mode provided up to 30 mA H{sup −} beam. Short cesiations, of the order of 10 mg effectively reduced the intensity of co-extracted electrons down to 2 - 8 times the H{sup −} current; this cesiated surface operation mode delivered up to 60 mA H{sup −} beam. An H{sup −} beam of the order of 40 mA was sustained up to four weeks operation with 500 μs pulses at 1.2s spacing. A new extraction was designed to match these beam properties. A copy of BNL’s magnetron produced at CERN was tested at BNL and delivered at 40 kV H{sup −} beam exceeding Linac4’s nominal intensity of 80 mA. In this contribution, the performances, dynamic response to cesiation, stability and availability of these prototypes are described. The needed optimization of the emittance of H{sup −} beam above 40 mA is presented, which requires an evolution of the front end that encompasses implementation of a large ceramic insulator.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High duty cycle inverse Compton scattering X-ray source

Inverse Compton Scattering (ICS) is an emerging compact X-ray source technology, where the small source size and high spectral brightness are of interest for multitude of applications. However, to satisfy the practical flux requirements, a high-repetition-rate ICS system needs to be developed. To this end, this article reports the experimental demonstration of a high peak brightness ICS source operating in a burst mode at 40 MHz. A pulse train interaction has been achieved by recirculating a picosecond CO 2 laser pulse inside an active optical cavity synchronized to the electron beam. The pulse train ICS performance has been characterized at 5- and 15- pulses per train and compared to a single pulse operation under the same operating conditions. Lastly, with the observed near-linear X-ray photon yield gain due to recirculation, as well as noticeably higher operational reliability, the burst-mode ICS offers a great potential for practical scalability towards high duty cycles.

43 PARTICLE ACCELERATORS↗

Real-Time Model-Adaptive Relaying Applied to Microgrid Protection

In microgrids, the short-circuit current magnitude is significantly limited by more than an order of magnitude due to the relatively small inverter-based resources. Commercially available protective devices for distribution cannot reliably protect a microgrid due to their dependence on the magnitude of the fault current. Moreover, overcurrent relays typically cannot function properly for a microgrid because they are incapable of detecting faults and/or performing the coordination between the relays in inverter-based microgrids operated in the islanded mode. This paper proposes a model-adaptive relay designed to adjust the relay curves based on the available generation and the network topology. The proposed method runs a real-time model of the microgrid, which gathers information from the network to calculate the available short-circuit current in the specified node. The fault current from the model is then used for the adaptive algorithm to calculate the relay settings, considering coordination with the downstream fuses and upstream reclosers. This work presents the validation of the proposed method in Hardware-in-the-Loop, in a hardware testbed as well as field deployed in a real microgrid in East-Tennessee.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Simulations of Multi-Mode Combustion Regimes Realizable In a Gasoline Direct Injection Engine

Lean and dilute gasoline compression ignition (GCI) operation in spark ignition (SI) engines are an attractive strategy to attain high fuel efficiency and low NOx levels. However, this combustion mode is often limited to low-load engine conditions due to the challenges associated with autoignition controllability. In order to overcome this constrain, multi-mode (MM) operating strategies, consisting of advanced compression ignition (ACI) at low load and conventional SI at high load, have been proposed. In this three-dimensional computational fluid dynamics study, the concept of multi-mode combustion using two RON98 gasoline fuel blends (Co-Optima Alkylate and E30) in a gasoline direct injection (GDI) engine were explored. To this end, a new reduced mechanism for simulating the kinetics of E30 fuel blend is introduced in this study. To cover the varying engine load demands for multi-mode engines, primary combustion dynamics observed in ACI and SI combustion modes was characterized and validated against experimental measurements. In order to implement part-load conditions, a strategy of mode transition between SI and ACI combustion (i.e., mixed-mode combustion) was then explored numerically by creating a virtual test condition. The results obtained from the mixed-mode simulations highlight an important feature that deflagrative flame propagation regime coexists with ignition-assisted end-gas autoignition. This study also identifies a role of turbulent flow property adjacent to premixed flame front in characterizing the mixed-mode combustion. The employed hybrid combustion model was verified to perform simulations aiming at suitable range of multi-mode engine operations.

Kim, Sayop↗

An Active and Robust Air Electrode for Reversible Protonic Ceramic Electrochemical Cells

Reversible protonic ceramic electrochemical cells (RPCECs) are a promising option for efficient and low-cost generation of electricity and hydrogen. Commercialization of R-PCECs, however, hinges on the development of highly active and robust air electrodes. Here, we report an air electrode consisting of PrBa 0.8 Ca 0.2 Co 2 O 5+δ and in situ exsolved BaCoO 3–δ nanoparticles (PBCC–BCO) that shows minimal polarization resistance (~0.24 Ω cm 2 at 600 °C) and high stability when exposed to humidified air with 3–50% H 2 O. An R-PCEC utilizing PBCC-BCO demonstrates remarkable performances at 600 °C: achieving a peak power density of 1.06 W cm –2 in the fuel cell mode and a current density of 1.51 A cm –2 at 1.3 V in an electrolysis mode. More importantly, the RPCECs demonstrate an exceptionally high durability over 1833 h of continuous operation in the electrolysis mode. Furthermore, this work offers an efficient approach to design of high-performance and durable electrodes for R-PCECs.

25 ENERGY STORAGE↗

Standard model and the lattice

The S U ( 3 ) ⊗ S U ( 2 ) ⊗ U ( 1 ) standard model maps smoothly onto a conventional lattice gauge formulation, including the parity violation of the weak interactions. The formulation makes use of the pseudoreality of the weak group and requires the inclusion a full generation of both leptons and quarks. As in continuum discussions, chiral eigenstates of the Dirac operator generate known anomalies, although with rough gauge configurations these are no longer exact zero modes of the Dirac operator. Published by the American Physical Society 2024

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Crystallization Characteristics and In-Mold Performance of Electroslag Remelting-Type TiO{sub 2}-Bearing Slag

The non-isothermal crystallization characteristics of the electroslag remelting (ESR)-type TiO{sub 2}-bearing slag were studied. The effect of crystallization characteristics of the slag on the in-mold performance was verified by ESR pilot trials operating in a static mode. The results showed that increasing TiO{sub 2} content decreased the crystallization temperature and liquidus temperature of the slag and suppressed the crystallization tendency of the slag. There is no change in the types of the crystalline phases in the slag with different TiO{sub 2} contents during cooling, i.e., 11CaO·7Al{sub 2}O{sub 3}·CaF{sub 2}, CaTiO{sub 3}, and CaF{sub 2}. The sequence of crystal precipitation during cooling was 11CaO·7Al{sub 2}O{sub 3}·CaF{sub 2} to CaTiO{sub 3}, and then CaF{sub 2} with increasing TiO{sub 2} content from 4.2 to 12.6 mass pct. With adding 16.8 mass pct TiO{sub 2} in the slag, the precipitation of 11CaO·7Al{sub 2}O{sub 3}·CaF{sub 2} and CaTiO{sub 3} took place simultaneously, followed by CaF{sub 2}. With the increase in the TiO{sub 2} content from 4.2 to 16.8 mass pct in the slag, the dominant crystalline phase changed from 11CaO·7Al{sub 2}O{sub 3}·CaF{sub 2} to CaTiO{sub 3}. The morphology of 11CaO·7Al{sub 2}O{sub 3}·CaF{sub 2} and CaTiO{sub 3} changed from faceted and bonelike to elliptically faceted and blocky, respectively. The morphology of CaF{sub 2} were spherical in all cases, irrespective of TiO{sub 2} contents in the slag. The decrease in the crystallization tendency of the slag with increasing TiO{sub 2} contents was attributed to the decrease in the activity of CaO in the slag. The increasing of TiO{sub 2} content in the slag are favorable for providing thin slag skin and stable heat flux across the slag skin, which improved the surface quality of the as-cast ESR ingot as demonstrated by ESR pilot trials operating in a static mode.

36 MATERIALS SCIENCE↗

Performance Validation of a Thermally Integrated 50 kW High Temperature Electrolyzer System

In the proposed project, INL and OxEon seek to improve the value proposition of hydrogen production by integrating reversible fuel cell operations at relatively small scale for distributed energy applications. This goal will be accomplished by converting a 50 kW solid oxide electrolysis cell or SOEC system into a reversible system that operates at 30 kW in electrolysis mode and approximately 10 kW in fuel cell mode. The reversible SOC system will be operated for over 3,000 hours using an improved catalyst in the fuel electrode. Steam for the electrolysis will come from an electric boiler Thermal Energy Distribution System that will be configured to mimic an industrial source of low-grade heat. Thermodynamic analysis will be performed to demonstrate the potential of the system to achieve >85% system efficiency in electrolysis mode. Finally, a technoeconomic analysis will be completed to show potential to produce hydrogen at a cost of $2/kg. The figure at the right indicates a target cost breakdown to achieve that goal.

08 HYDROGEN↗