Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES - ELASTICITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Simulations of Sweeping Wave Propagation in a Boron Carbide Plate

In February 2020, experiments were conducted at Los Alamos National Laboratory measuring the propagation of a sweeping wave through a plate of boron carbide which was induced by detonating an adjacent charge of high explosive. Six such shots were red and in each case progress of the wave along the exposed surface of the plate was tracked using photon doppler velocimetry (PDV). In this report we discuss calculations performed using the Lagrangian hydrocode FLAG to model data taken from these experiments. We discuss the models chosen for the different experimental components, the choice of mesh (focusing on, both, two- and three-dimensional geometries), and compare the results from these calculations to experimentally-extracted PDV traces. Notably, we find that the PDV traces for this experiment are most faithfully reproduced using the full three-dimensional geometry, even when the mesh resolution for the three-dimensional calculations was significantly lower than the resolution for the corresponding two-dimensional calculations. We attribute this to the geometry of the experimental setup. Moreover, we find only negligible differences for the PDV traces obtained using the sesame table equation of state for boron carbide and the Gruneisen equation of state.

36 MATERIALS SCIENCE↗

Empirical Formula for Puncture Energy of Flat Metal Plates by a Cylindrical Flat Punch

Impact problems of plate-like parts by punch-like objects with relatively large mass moving at slow speeds of a few feet per second constitute a subset of impact problems of interest at Sandia. This is in contrast to small objects moving in the range of hundreds or thousands of feet per second or higher. The objective of this work is to develop a simple formula that can be used to estimate a lower bound for the puncture energy of metal plates impacted by cylindrical, essentially rigid punches of circular cross-section and at nose. Such geometry is used as a basis in the design of puncture mitigation barriers or procedures. This was accomplished by deriving an expression using non-dimensional analysis and then calibrating it based on tests results in the range of speeds of interest. Lower bounds can then be determined based on confidence intervals or factors of safety.

36 MATERIALS SCIENCE↗

Measurements of the Dielectric Properties of Thin High-Explosive Samples Using a Parallel Plate Test Fixture

This report presents results of a study of the dielectric properties of several high explosive materials, including Composition B, C-4, Detasheet, Semtex 1A, Semtex 1H, and Semtex 10. The capacitance and dispersion of samples up to ten mm thick were measured at 24 and 65°C using a parallel plate test fixture. In this configuration, capacitance is proportional to the real component of the complex dielectric constant (or permittivity) of the material, while the dispersion is equal to the imaginary component of the dielectric constant divided by the real component. Measurements were performed at two temperatures to determine whether these dielectric properties might be used to monitor moderate temperature changes within these materials using an external fringing field capacitor. It was found that the real dielectric constant of the high explosives generally changed by only about 1% on heating from 24 to 65°C, and that the externally measured capacitance is therefore not a reliable parameter for monitoring temperature changes in these explosives. Temperature- based changes in the dispersion were often 20% or greater, and for several materials (e.g., Composition B, Detasheet) the temperature and dispersion showed good correlation as the temperature of the explosive was cycled up and down. It is thus possible that for some high explosives the externally measured dispersion is a useful parameter for monitoring temperature changes. However, other factors may limit the usefulness of this technique, including the need to have the plates of a fringing field capacitor in direct contact with the high explosive to obtain measurements, and the limited penetration depth of the fringing field into the explosive material.

36 MATERIALS SCIENCE↗

Large Plate Experiment of Chloride-induced Stress Corrosion Cracking in Spent Nuclear Fuel Storage Canisters

This report is the comprehensive description of the completed experiment to evaluate the corrosion behavior of a large section of welded plate material harvested from the Sandia National Laboratories’ (SNL) full-size mockup of a spent nuclear fuel (SNF) dry storage canister. The plate was subjected to conditions aggressive to chloride-induced stress corrosion cracking for a total time of 2 years. The details of the establishment of this experiment, and the corrosion results are reported. This work is intended to inform aging management programs for SNF canisters under conditions of extended dry storage.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Summary of Chloride-induced Stress Corrosion Cracking Experiments with a Spent Fuel Storage Canister Large Plate

This report provides a comprehensive summary of the crack growth rate testing and the experiments to evaluate the corrosion behavior of welded plate material taken from the Sandia National Laboratories’ full-size mockup of a spent nuclear fuel (SNF) dry storage canister. The information includes that previously reported, and new work on detailed surface characterization of the corrosion attack from the large plate experiment. The work and the results inform aging management programs for the SNF canisters.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

First-Principles Studies of Tritium Species Dissociability & Diffusivity Across the Interface of Nickel-Plated Zircaloy-4

Zirconium (Zr) and its alloys (Zircaloy-4) are widely used in nuclear reactors due to their low neutron adsorption cross-section and excellent corrosion resistance. In tritium-producing burnable absorber rods (TPBARs), the metal getter tube located between the cladding and the γ-LiAlO 2 pellets is composed of nickel (Ni)-plated Zircaloy-4, which is used to capture tritium ( 3 H) species (mainly 3 H 2 and 3 H 2 O) generated from γ-LiAlO 2 pellets during irradiation. The 3 H-related products transfer to the surface of metal Ni upon adsorption and dissociation to form new 3 H species and diffuse into the Zircaloy-4 getters to form metal hydrides (Zr 3 H x ). Therefore, exploring 3 H species ( 3 H 2 , 3 H 2 O) dissociation on the surface of Ni and diffusion across the interface of Ni-plated Zircaloy-4 getters can provide a better understanding of 3H species formation and transport from pellets into the getters.

36 MATERIALS SCIENCE↗

Neutron Absorber Plate Characterization Plan for Criticality Experiments Design [Slides]

The goal of this presentation is to show the feasibility of performing a critical experiment with a B 4 C/Aluminum alloy neutron absorber plate. The motivation of this experiment is to provide integral data on modern neutron absorber product “Boralcan” by Rio Tinto. In 2020, used in about 20% of spent fuel pools in the US, and in casks for storage and transportation in the US and in Europe. The added value of this experiment: Neutron absorber plate modeling method verification: homogeneous or not, a lot of potential savings by relaxing boron loading credit limits. No available critical benchmark involving Boralcan, other boron-related experiments are relatively old. Nuclear data validation for B, C, and Al in the form of B 4 C in Al matrix.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Design and Analysis of 10” Parallel Plate Relief Device

All Cryomodule (CM) and Cryogenic Distribution System (CDS) relieving into Helium Low Pressure (LP) return header, which is connected to compressor suction so, helium can be preserved during small flow relieving event and recirculated to system. However, during worst case scenario, Helium LP header requires a parallel plate relief device to relieve excess pressure from header. To complete the CDS Warm piping header, a new design for a 10 parallel plate relief device is necessary to relieve outside of the tunnel into atmosphere.

Chicas, Kelly↗

In Situ Li Seed Formation Enables Uniform Plating in Anode-Free Solid-State Batteries

Anode-free solid-state batteries (AFSSBs) are a promising route toward achieving high energy density. In these cells, the anode contains no pre-stored lithium (Li). Instead, all Li inventory originates from the cathode and is freshly deposited onto a bare current collector during charging. However, achieving uniform and defect-free Li plating on this bare current collector remains a major challenging, often resulting in low Li plating/stripping efficiency and rapid capacity decay. Here, for the first time, operando neutron imaging is employed to visualize Li plating/stripping behavior in an anode-free full cell with LiNi 0.82 Mn 0.07 Co 0.11 O 2 (NMC) as the cathode. Operando measurements reveal that complete stripping of Li leaves isolated Li residues on the current collector, which degrades interfacial contact between the current collector and solid-state electrolyte. To mitigate this interfacial issue and promote more uniform Li deposition, we implement a discharge cutoff voltage strategy that intentionally retains a thin residual Li layer after stripping. This thin Li layer, serving as an in situ–formed seed layer, not only enables more homogeneous subsequent Li plating but also improves interfacial contact. As a result, the anode-free cell with a controlled discharge voltage of 3.5 V exhibits excellent long-term cycling stability, maintaining a discharge capacity of 116 mAh g -1 with a retention rate of 83.4% and an average Coulombic efficiency of approximately 99.9% after 430 cycles at 0.25 C. In contrast, the cell with a conventional discharge cutoff voltage of 2.8 V exhibits rapid capacity decay, retaining only 59.7 mAh g -1 after 50 cycles with a capacity retention of 40.7%. This work offers a practical strategy to unlock the long-term viability of anode-free solid-state batteries.

25 ENERGY STORAGE↗

Calculation of the temperature of the internal surface of the heat-removing channel wall of the ray-absorbing heat-exchange panels of flat-plate solar water-heating collectors

The results of numerical research on the determination of the temperature value of the internal surface of the heat-removing channel (HRC) walls of the light-absorbing heat-exchange panels (LAHPs) with the tubeon- sheet and thin-parallelepiped form of flat-plate solar water-heating collectors (FPSWHCs) are presented. The research method is based on compilation of the system of the balance equations for the light-absorbing plate (LAP) and HRCs of the LAHPs of the studied types and their designs with respect to the desired parameter. A practical example of calculation of the determination of the temperature value of the internal surface of the HRC wall of the tube-on-sheet LAHP, where the results of experimental research on the determination of the specific thermal efficiency of the mean-quality FPSWHC in full-scale terms, as well as laboratory and numerical research on determination of the optical and thermotechnical indicators of the copper tube-on-sheet LAHP.

14 SOLAR ENERGY↗

2 kV Al 0.64 Ga 0.36 N-channel high electron mobility transistors with passivation and field plates

Abstract High voltage (∼2 kV) Al 0.64 Ga 0.36 N-channel high electron mobility transistors were fabricated with an on-resistance of ∼75 Ω. mm (∼21 mΩ. cm 2 ). Two field plates of variable dimensions were utilized to optimize the breakdown voltage. The breakdown voltage reached >3 kV (tool limit) before passivation however it reduced to ∼2 kV after Si 3 N 4 surface passivation and field plate deposition. The breakdown voltage and on-resistance demonstrated a strong linear correlation in a scattered plot of ∼50 measured transistors. The fabricated transistors were electrically characterized and benchmarked against the state-of-the-art high-voltage (> 1 kV) Al-rich (>40%) AlGaN-channel transistors in breakdown voltage and on-resistance, indicating significant progress.

Alam, Md Tahmidul (ORCID:000900086556839X)↗

On-sky performance analysis of the vector apodizing phase plate coronagraph on MagAO/Clio2

We report on the performance of a vector apodizing phase plate coronagraph that operates over a wavelength range of 2–5 μm and is installed in MagAO/Clio2 at the 6.5 m Magellan Clay telescope at Las Campanas Observatory, Chile. The coronagraph manipulates the phase in the pupil to produce three beams yielding two coronagraphic point-spread functions (PSFs) and one faint leakage PSF. The phase pattern is imposed through the inherently achromatic geometric phase, enabled by liquid crystal technology and polarization techniques. The coronagraphic optic is manufactured using a direct-write technique for precise control of the liquid crystal pattern and multitwist retarders for achromatization. By integrating a linear phase ramp to the coronagraphic phase pattern, two separated coronagraphic PSFs are created with a single pupil-plane optic, which makes it robust and easy to install in existing telescopes. The two coronagraphic PSFs contain a 180° dark hole on each side of a star, and these complementary copies of the star are used to correct the seeing halo close to the star. To characterize the coronagraph, we collected a data set of a bright (m{sub L} = 0–1) nearby star with ∼1.5 hr of observing time. By rotating and optimally scaling one PSF and subtracting it from the other PSF, we see a contrast improvement by 1.46 magnitudes at 3.5 λ/D. With regular angular differential imaging at 3.9 μm, the MagAO vector apodizing phase plate coronagraph delivers a 5σ Δmag contrast of 8.3 (=10{sup −3.3}) at 2 λ/D and 12.2 (=10{sup −4.8}) at 3.5 λ/D.

79 ASTRONOMY AND ASTROPHYSICS↗

Scanning Electron Microscopy Analysis of Fuel/Matrix Interaction Layers in Highly-Irradiated U–Mo Dispersion Fuel Plates with Al and Al–Si Alloy Matrices

In order to investigate how the microstructure of fuel/matrix-interaction (FMI) layers change during irradiation, different U–7Mo dispersion fuel plates have been irradiated to high fission density and then characterized using scanning electron microscopy (SEM). Specifially, samples from irradiated U–7Mo dispersion fuel elements with pure Al, Al–2Si and AA4043 (~4.5 wt.%Si) matrices were SEM characterized using polished samples and samples that were prepared with a focused ion beam (FIB). Features not observable for the polished samples could be captured in SEM images taken of the FIB samples. For the Al matrix sample, a relatively large FMI layer develops, with enrichment of Xe at the FMI layer/Al matrix interface and evidence of debonding. Overall, a significant penetration of Si from the FMI layer into the U–7Mo fuel was observed for samples with Si in the Al matrix, which resulted in a change of the size (larger) and shape (round) of the fission-gas bubbles. Additionally, solid-fission-product phases were observed to nucleate and grow within these bubbles. These changes in the localized regions of the microstructure of the U–7Mo may contribute to changes observed in the macroscopic swelling of fuel plates with Al–Si matrices.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effects of Accident Thermal Loading on In-Plane Shear Behavior of Steel-Plate Composite Walls

Structural walls in safety-related nuclear facilities are required to be designed for seismic and accident thermal (due to postulated high-energy pipe break events) loading combination. Current U.S. and international codes provide limited guidance for analysis and design of walls for this loading combination. This paper describes the experimental results and observations from tests conducted on a laboratory-scale (1:4 to 1:5) test unit representing steel-plate composite (SC) walls subjected to combined in-plane (seismic) and accident thermal loading. The test unit was subjected to surface temperatures of up to 450°F in combination with cyclic in-plane loading. Results of similar experiments recently conducted in Japan are also summarized (with surface temperatures up to 570°F). Surface heating combined with the low thermal conductivity and high specific heat of concrete resulted in nonlinear thermal gradients through the thickness of the specimens. These nonlinear thermal gradients and the associated self- or internal restraint led to extensive concrete cracking. This concrete cracking reduced the initial and secant stiffness of the specimens. The initial stiffness of the heated specimens reduced to 30 to 40% of the initial stiffness of the control (unheated) specimen. The secant stiffness of the heated specimens reduced up to 50% of the secant stiffness of the control (unheated) specimen. However, the in-plane shear strength of the heated SC specimens was still approximately 10 to 30% greater than the nominal in-plane shear strength calculated, for the limit state of steel plate von Mises yielding, using AISC N690 equations and measured material properties. Evaluation of the experimental results and observations suggests that the in-plane shear strength of SC walls subjected to typical accident surface temperatures (up to 570°F) can be estimated conservatively using the current provisions of AISC N690. The stiffness for accident thermal loading combinations can be considered to reduce from cracked composite stiffness at ambient temperature to fully cracked—that is, steel-only stiffness as the surface temperature increases up to typical accident value.

Construction & Building Technology↗

Metals plated on fluorocarbon polymers

Electroplating lead on fluorocarbon polymer parts is accomplished by etching the parts to be plated with sodium, followed by successive depositions of silver and lead from ultrasonically agitated plating solutions. Metals other than lead may be electroplated on the silvered parts.

Ford, H.↗