Search NASA⌕ Search

SEARCH · Search NASA

Results for “Parametric Operators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Parametric study of the lubrication of thrust loaded 120-mm bore ball bearings to 3 million DN

A parametric study was performed with 120-mm bore angular-contact ball bearings under varying thrust loads, bearing and lubricant temperatures, and cooling and lubricant flow rates. Contact angles were nominally 20 and 24 deg with bearing speeds to 3 million DN. Endurance tests were run at 3 million DN and a temperature of 492 K (425 F) with 10 bearings having a nominal 24 deg contact angle at a thrust load of 22241 N (5000 lb). Bearing operating temperature, differences in temperatures between the inner and outer races, and bearing power consumption can be tuned to any desirable operating requirement by varying 4 parameters. These parameters are outer-race cooling, inner-race cooling, lubricant flow to the inner race, and oil inlet temperature. Preliminary endurance tests at 3 million DN and 492 K (425 F) indicate that long term bearing operation can be achieved with a high degree of reliability.

Signer, H.↗

The measurement of atmospheric water vapor - Radiometer comparison and spatial variations

Two water vapor radiometer (WVR) experiments were conducted to evaluate whether such instruments are both suitable and necessary to correct for propagation effects that are induced by precipitable water vapor (PWV) on signals from GPS and VLBI. WVRs are suitable for these corrections if they provide wet path delays to better than 0.5 cm. They are needed if spatial variations of PWV result in complicated, direction-dependent propagation effects that are too complex to be parametrized in the GPS or VLBI geodetic solution. The suitability of radiometers was first addressed by comparing six airport WVRs for two weeks. While two WVRs showed an average wet path delay bias of only 0.1 cm, others were biased by 1-3 cm relative to each other and relative to radiosondes. The second experiment addressed the question whether radiometers are needed for the detection of inhomogeneities in the wet delay. Three JPL D-series radiometers were operated at three sites 50 km apart. The WVRs simultaneously sampled PWV at different azimuths and elevations in search of spatial variations of PWV. On one day of this second experiment evidence was found for spatial variations of the wet path delay as high as 20 percent of the total wet path delay.

Rocken, C.↗

A Deformed Geometry Synthesis Technique for Determining Stacking and Cryogenically Induced Preloads for the Space Launch System

The Space Launch System (SLS) stacking and Core Stage (CS) fueling induce significant preloads that contribute to the liftoff pad separation “twang”. To accurately capture this, an approach is required that can replicate the physics of all SLS physical stacking steps, CS cryogenic shrinkage, associated geometric nonlinearities, and the transient behavior and decay of the preloads with changing boundary conditions as the vehicle separates from the pad. The Deformed Geometry Synthesis (DGS) approach presented here satisfies the above requirements. DGS determines induced preloads by modeling components in their deformed geometry states and then enforcing compatibility by closing the resulting “deadbands”. DGS seamlessly integrates into the multibody modal synthesis framework and does not require the use of artificial external loads to enforce preloads or post-processing steps to remove their influence. Since DGS iterates to solve for the deformed state inclusive of geometric nonlinearities, running linearized parametrics to exercise different potential orientations of ball jointed struts that connect the CS to Boosters for cryo-shrinkage analyses is entirely avoided. Relative to the transient behavior and decay of stacking and cryo-induced preloads with SLS liftoff pad separation, this is an area of considerable interest to the SLS program. To capture this in the most accurate way possible, DGS algorithms are designed to work with Henkel-Mar nonlinear pad separation algorithms which operate on the separating longitudinal and lateral degrees of freedom (DoFs) between the vehicle and the pad. As the separating DoFs release, in whatever manner as dictated by the interface geometries, interface loads and interface flexibilities as well as the external loading on the vehicle, the subject preloads generate a complex twang/decay time-trace as dictated by the physics of the problem. This paper presents DGS numerical verification against the closed-form solution for Timoshenko’s 3 ball-jointed strut preload problem. This problem is then extended by the authors to the geometric nonlinear case where DGS is compared to the Newton-Raphson solution of the nonlinear equations. Next, DGS is utilized to solve the SLS stacking and cryogenic shrinkage coupled loads analyses. Finally, Henkel-Mar pad separation simulations are executed that isolate the impact of the induced preloads’ twang and decay characteristics.

Space Launch System↗

SELF-DESTRUCTING SPIRAL WAVES: GLOBAL SIMULATIONS OF A SPIRAL-WAVE INSTABILITY IN ACCRETION DISKS

We present results from a suite of three-dimensional global hydrodynamic simulations that shows that spiral density waves propagating in circumstellar disks are unstable to the growth of a parametric instability that leads to break down of the flow into turbulence. This spiral wave instability (SWI) arises from a resonant interaction between pairs of inertial waves, or inertial-gravity waves, and the background spiral wave. The development of the instability in the linear regime involves the growth of a broad spectrum of inertial modes, with growth rates on the order of the orbital time, and results in a nonlinear saturated state in which turbulent velocity perturbations are of a similar magnitude to those induced by the spiral wave. The turbulence induces angular momentum transport and vertical mixing at a rate that depends locally on the amplitude of the spiral wave (we obtain a stress parameter α ∼ 5 × 10{sup −4} in our reference model). The instability is found to operate in a wide range of disk models, including those with isothermal or adiabatic equations of state, and in viscous disks where the dimensionless kinematic viscosity ν ≤ 10{sup −5}. This robustness suggests that the instability will have applications to a broad range of astrophysical disk-related phenomena, including those in close binary systems, planets embedded in protoplanetary disks (including Jupiter in our own solar system) and FU Orionis outburst models. Further work is required to determine the nature of the instability and to evaluate its observational consequences in physically more complete disk models than we have considered in this paper.

79 ASTRONOMY AND ASTROPHYSICS↗

Experimentally validated multiphysics modeling of fracture induced by thermal shocks in sintered UO 2 pellets

Uranium Dioxide (UO 2 ) fuel powers almost all commercial Nuclear Power Plants (NPPs) worldwide, generating carbon-free energy and contributing to the fight against climate change. UO 2 fuel incurs damage and fractures due to large thermal gradients that develop across the fuel pellet during normal and transient operating conditions. A comprehensive understanding of the underlying mechanisms by which these processes take place is still lacking. A combined experimental and computational approach is utilized here to quantify the behavior of UO 2 fuel fracture induced by thermal shock. Here, this work introduces both (1) an experimental study to understand the fuel fracturing behavior of sintered UO 2 pellets when exposed to thermal shock, and (2) a Multiphysics phase-field fracture model capable of simulating this process. Parametric studies were conducted to evaluate the effects of uncertainties in fracture properties on the fracture behavior of UO 2 due to thermal shocking. A set of energy release rate (or equivalently fracture toughness) and contract area (the part of the fuel pellet in direct contact with the cold bath) were able to capture the overall fracture trends of the corresponding experimental data. Our combined approach presents a new method for accounting for the effects of microstructure and sample size on the energy release rate/fracture toughness. The experimental data were collected from multiple experiments that exposed UO 2 pellets to high-temperature conditions (589–676 °C) followed by a quench in sub-zero water. This work demonstrates that joint experimental and computational efforts are able to advance the understanding of thermal fracture in the primary fuel source for existing and future NPPs.

36 MATERIALS SCIENCE↗

Effects of grain size and porosity on cladding failure in high-burnup UO 2 : A sensitivity and uncertainty study

Isotopic taggants are being studied to aid in the provenance assessment of nuclear materials. However, these taggants must be selected such that they do not adversely affect fuel performance during normal operation or accident scenarios. Taggants are known to affect the fuel’s grain size and porosity. In the work described in this paper, the BISON fuel performance code was used to assess the potential effects of taggants (i.e., grain size and porosity) on fuel rod behavior and cladding failure during a high-burnup, large-break loss-of-coolant accident. Here, 281 individual fuel rods from the same reactor core were modeled for a sensitivity study, a parametric study, and uncertainty quantification. The cladding failure predictions often exhibited stochastic behavior. After additional study, it was found that the cladding failure model is highly sensitive to residual error inherent to numerical approximation solvers. Some strategies to mitigate this sensitivity are discussed. The study found no relationship between known taggant effects and cladding failure status. However, taggants were found to affect the time and location of failure in certain rods. In conclusion, future work to continue investigating and validating these findings is briefly discussed.

Doped UO 2↗

Visible BaB2O4 optical parametric oscillator pumped at 355 nm by a single-axial-mode pulsed source

A visible BaB2O4 optical parametric oscillator (OPO) pumped by a single-axial-mode 355-nm source has been demonstrated. An average output power of 140 mW with a signal wave conversion efficiency of 13 percent and an idler conversion efficiency of 11 percent for a total conversion efficiency of 24 percent has been achieved. The oscillator has continuously tuned from 412 nm to 2.55 microns limited by the infrared transmission range of the crystal. Through injection seeding, single-axial-mode OPO operation with a corresponding OPO linewidth of less than 3 GHz was obtained.

Fan, Y. X.↗

An experimental parametric study of geometric, Reynolds number, and ratio of specific heats effects in three-dimensional sidewall compression scramjet inlets at Mach 6

The effects of the decrease in the ratio of specific heats have been investigated in generic 3D sidewall compression scramjet inlets with leading-edge sweep angles of 30 and 70 degrees. The effects of a decrease in ratio of specific heats were seen by comparing data from two facilities in two test gases: in the Langley Mach 6 CF4 Tunnel in tetrafluoromethane and in the Langley 15-Inch Mach 6 Air Tunnel in perfect gas air. In addition to the simulated real gas effects, the parametric effects of cowl position, contraction ratio, leading-edge sweep, and Reynolds number were investigated in the 15-Inch Mach 6 Air Tunnel. The models were instrumented with a total of 45 static pressure orifices distributed on the sidewalls and baseplate. Surface streamline patterns were examined via oil flow, and schlieren videos were made of the external flow field. The results of these tests have significant implications to ground based testing of inlets in facilities which do not operate at flight enthalpies.

Holland, Scott D.↗

Design of high performance multivariable control systems for supermaneuverable aircraft at high angle of attack

The main motivation for the work under the present grant was to use nonlinear feedback linearization methods to further enhance performance capabilities of the aircraft, and robustify its response throughout its operating envelope. The idea was to use these methods in lieu of standard Taylor series linearization, in order to obtain a well behaved linearized plant, in its entire operational regime. Thus, feedback linearization was going to constitute an 'inner loop', which would then define a 'design plant model' to be compensated for robustness and guaranteed performance in an 'outer loop' application of modern linear control methods. The motivation for this was twofold; first, earlier work had shown that by appropriately conditioning the plant through conventional, simple feedback in an 'inner loop', the resulting overall compensated plant design enjoyed considerable enhancement of performance robustness in the presence of parametric uncertainty. Second, the nonlinear techniques did not have any proven robustness properties in the presence of unstructured uncertainty; a definition of robustness (and performance) is very difficult to achieve outside the frequency domain; to date, none is available for the purposes of control system design. Thus, by proper design of the outer loop, such properties could still be 'injected' in the overall system.

Valavani, Lena↗

An Experimental Parametric Study of Geometric, Reynolds Number, and Ratio of Specific Heats Effects in Three-Dimensional Sidewall Compression Scramjet Inlets at Mach 6

Since mission profiles for airbreathing hypersonic vehicles such as the National Aero-Space Plane include single-stage-to-orbit requirements, real gas effects may become important with respect to engine performance. The effects of the decrease in the ratio of specific heats have been investigated in generic three-dimensional sidewall compression scramjet inlets with leading-edge sweep angles of 30 and 70 degrees. The effects of a decrease in ratio of specific heats were seen by comparing data from two facilities in two test gases: in the Langley Mach 6 CF4 Tunnel in tetrafluoromethane (where gamma=1.22) and in the Langley 15-Inch Mach 6 Air Tunnel in perfect gas air (where gamma=1.4). In addition to the simulated real gas effects, the parametric effects of cowl position, contraction ratio, leading-edge sweep, and Reynolds number were investigated in the 15-Inch Mach 6 Air Tunnel. The models were instrumented with a total of 45 static pressure orifices distributed on the sidewalls and baseplate. Surface streamline patterns were examined via oil flow, and schlieren videos were made of the external flow field. The results of these tests have significant implications to ground based testing of inlets in facilities which do not operate at flight enthalpies.

Holland, Scott D.↗

Results for an Electrified Aircraft Propulsion Design Exploration

An electrified aircraft propulsion (EAP) design exploration study was performed to determine the impact of EAP technologies on a set of regional transport aircraft concepts. A range of aircraft sizes and types were assessed, including 18, 48, and 70 passenger turboprops, as well as 50 and 78 passenger turbofan aircraft configurations. A previous paper discussed the approaches, technology assumptions, and tools used to carry out the design exploration. The study team designed a series of baseline and advanced EAP aircraft concepts based on existing reference aircraft in the fleet. We then conducted a set of parametric trade studies on the EAP aircraft to better understand the design and performance implications of EAP. This paper documents results from the trade studies, including battery weight versus motor size, climb hybrid power versus cruise hybrid power, and range vs. battery specific energy. Assuming a 500 W-hr/kg battery specific energy, the turboprop aircraft demonstrated a significant fuel savings and modest energy savings. The turbofan aircraft demonstrated no fuel or energy benefits from electrification. In addition, operating cost results are presented on the most promising EAP designs. The cost analysis revealed that the EAP aircraft concepts were not competitive with their baselines, mainly due to the additional depreciation and interest cost for the much heavier and more expensive EAP aircraft.

Ty V Marien↗

Development of an Unmanned Mobile Current Turbine Platform: Preprint

The design and development of a prototype unmanned mobile floating platform, equipped with a custom low-flow marine current turbine for autonomously seeking and harnessing tidal/coastal currents is described. The platform is an unmanned surface vehicle in the form of a catamaran with two electric outboard motors and capabilities for autonomous navigation. An undershot water wheel, aided by a custom flow concentrator, has been selected as the basic design for the marine current turbine, which is mounted on the stern of the unmanned surface vehicle platform. The concept of operation is that the platform would navigate to a designated marine current resource, autonomously anchor at the location, align itself in the current and deploy the current turbine using a custom cable-lift deployment mechanism. As the turbine harnesses the local current, an onboard power-take-off device converts the harnessed mechanical energy to electricity which is stored in onboard batteries. Considerations of deployment in tidal and coastal waters required obtaining the necessary environmental permits for conducting in-water testing; developing required mitigation measures in protecting local wildlife and their habitats; and identifying potential in-water test sites and surveying them for their suitability in terms of the current resource, bottom type, water depth, and local boat traffic. The design and development of the turbine and the results of initial in-water testing are discussed. The potential for scaling up the system for extended capacity is presented.

ENGINEERING,TIDAL AND WAVE POWER↗

Completion of the Edward Air Force Base Statistical Guidance Wind Tool

The goal of this task was to develop a GUI using EAFB wind tower data similar to the KSC SLF peak wind tool that is already in operations at SMG. In 2004, MSFC personnel began work to replicate the KSC SLF tool using several wind towers at EAFB. They completed the analysis and QC of the data, but due to higher priority work did not start development of the GUI. MSFC personnel calculated wind climatologies and probabilities of 10-minute peak wind occurrence based on the 2-minute average wind speed for several EAFB wind towers. Once the data were QC'ed and analyzed the climatologies were calculated following the methodology outlined in Lambert (2003). The climatologies were calculated for each tower and month, and then were stratified by hour, direction (10" sectors), and direction (45" sectors)/hour. For all climatologies, MSFC calculated the mean, standard deviation and observation counts of the Zminute average and 10-minute peak wind speeds. MSFC personnel also calculated empirical and modeled probabilities of meeting or exceeding specific 10- minute peak wind speeds using PDFs. The empirical PDFs were asymmetrical and bounded on the left by the 2- minute average wind speed. They calculated the parametric PDFs by fitting the GEV distribution to the empirical distributions. Parametric PDFs were calculated in order to smooth and interpolate over variations in the observed values due to possible under-sampling of certain peak winds and to estimate probabilities associated with average winds outside the observed range. MSFC calculated the individual probabilities of meeting or exceeding specific 10- minute peak wind speeds by integrating the area under each curve. The probabilities assist SMG forecasters in assessing the shuttle FR for various Zminute average wind speeds. The A M ' obtained the processed EAFB data from Dr. Lee Bums of MSFC and reformatted them for input to Excel PivotTables, which allow users to display different values with point-click-drag techniques. The GUI was created from the PivotTables using VBA code. It is run through a macro within Excel and allows forecasters to quickly display and interpret peak wind climatology and probabilities in a fast-paced operational environment. The GUI was designed to look and operate exactly the same as the KSC SLF tool since SMG forecasters were already familiar with that product. SMG feedback was continually incorporated into the GUI ensuring the end product met their needs. The final version of the GUI along with all climatologies, PDFs, and probabilities has been delivered to SMG and will be put into operational use.

Dreher, Joseph G.↗

Parametric performance of circumferentially grooved heat pipes with homogeneous and graded-porosity slab wicks at cryogenic temperatures

A recently developed, potentially high-performance nonarterial wick was extensively tested. This slab wick has an axially varying porosity which can be tailored to match the local stress imposed on the wick. The purpose of the tests was to establish the usefulness of the graded-porosity slab wick at cryogenic temperatures between 110 and 260 K, with methane and ethane as working fluids. For comparison, a homogeneous (i.e., uniform porosity) slab wick was also tested. The tests included: maximum heat pipe performance as a function of fluid inventory, maximum performance as a function of operating temperature, maximum performance as a function of evaporator elevation, and influence of slab wick orientation on performance. The experimental data were compared with theoretical predictions obtained with the GRADE computer program.

Groll, M.↗

Operational Condition and Superfinishing Effect on High-Speed Helical Gearing System Performance

An experimental effort has been conducted on an aerospace-quality helical gear train to investigate the thermal behavior of the gear system. Oil inlet temperature was varied from 160 to 250 F. Also, the test gears were run in both an as-ground condition and after isotropic superfinishing (ISF) condition. In-depth temperature measurements were made across the face width and at the axial end of the gear mesh. Supply power measurements were made at varying speeds and loads up to 5000 hp and 15000 rpm (pitch line velocity to 24000 feet per minute). Test results from the parametric studies and the superfinishing process are presented. The tests indicated that superfinishing offered no improvement in performance due to the high lubricant film thickness generated by the extremely high pitch line velocity that the majority of the tests were conducted. Increasing lubricant inlet temperature had the most dramatic effect on performance improvement.

Handschuh, R.↗

Production of oxygen from lunar ilmenite

The overall objective of this project was to develop a novel carbothermal reduction process for production of oxygen from lunar ilmenite. The specific objective was to use a reaction sequence in which a wide variety of carbonaceous compounds (including carbonaceous wastes) can be used as reducing agents. During the first phase, two reactor systems were designed, constructed, and operated to study the reaction fundamental important in this process. One system is a small fluidized bed, and the other is a thermo-gravimetric reactor system. Preliminary experiments on synthetic ilmenite are conducted to study the effect of carbon type, carbon loading, temperature, and gas flow rate. Results indicate that a reaction path based on carbon gasification can be used to promote the overall kinetics. A unique temperature and concentration-programmed reaction procedure was being developed for rapid parametric study of the process.

Shadman, F.↗

Flow visualization studies of the internal flow characteristics in a simulated mixed flow vectored thrust ASTOVL engine configuration

The characteristics of internal flowfields in a Mixed Flow Vectored Thrust (MFVT) propulsion system for Short Take Off and Vertical Landing (STOVL) fighter aircraft were investigated using flow visualization techniques. A highly parametric 14 percent scale transparent model was used to simulate the MFVT propulsion system. The working medium was water. The mixing between the fan and core flow was studied using flow visualization for a variety of geometrical and flow parameters including three bypass ratio variations. The flow visualization technique involves the use of laser light sheet for illumination and fluorescent dye or air bubbles as tracers. Results indicate the existence of a strong vortex flowfield in the hover mode of operation that is responsible for good mixing between the fan and core flows.

Saripalli, K. R.↗

Science Yield Estimates and Sensitivities With the AstroPIC Integrated Photonic Coronagraph for the Habitable Worlds Observatory

The Habitable Worlds Observatory (HWO) flagship has a goal to survey ~100 of the nearest stellar systems and their habitable zones in order to detector and spectroscopically characterize ~25 potentially “Earth-like planets” (or “Exoearths”). The HWO telescope will feature a >6-m diameter aperture and a coronagraph that will suppress starlight by ten orders of magnitude to enable the detection and characterization of Earth analogues in the habitable zone. Three Exploratory Analytic Cases (EACs) are currently considering different aperture configurations for HWO including on-axis and off-axis apertures and both different hexagonal and keystone segmentation configurations. Photonic Integrated Circuits (PICs) offer a path to miniaturize traditional, bulk optics coronagraph functionality reducing risk margins and increasing mission science exoearth yields for the HWO mission. We have developed a simulation pipeline that enables evaluation of the AstroPIC photonic integrated coronagraph through to estimates mission yields. We present sensitivities to aberrations for different types of segmentation and low-order aberrations for HWO EACs demonstrating that AstroPIC is suitable for both on-axis and off-axis configurations. We perform a parametric sweep of the exoearth science yield sensitivities in terms of key coronagraph parameters including coronagraphic end-to-end throughput, inner working angle, robustness to aberrations, and bandwidth. We consider both a hybrid and a pure photonic architecture; a pure integrated photonic architecture provides the greatest potential in science yield improvements, although a hybrid PIC limited in its numbers of modes can provide complementary science to a traditional, bulk-optic coronagraph and increasing the estimated science yield when operated jointly.

Photonics↗