Search NASA⌕ Search

SEARCH · Search NASA

Results for “atomic processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Precision Tomography of a Three-Qubit Donor Quantum Processor in Silicon

Nuclear spins were among the first physical platforms to be considered for quantum information processing, because of their exceptional quantum coherence and atomic-scale footprint. However, their full potential for quantum computing has not yet been realized, owing to the lack of methods with which to link nuclear qubits within a scalable device combined with multi-qubit operations with sufficient fidelity to sustain fault-tolerant quantum computation. Here we demonstrate universal quantum logic operations using a pair of ion-implanted 31 P donor nuclei in a silicon nanoelectronic device. A nuclear two-qubit controlled-Z gate is obtained by imparting a geometric phase to a shared electron spin, and used to prepare entangled Bell states with fidelities up to 94.2(2.7)%. The quantum operations are precisely characterized using gate set tomography (GST), yielding one-qubit average gate fidelities up to 99.95(2)%, two-qubit average gate fidelity of 99.37(11)% and two-qubit preparation/measurement fidelities of 98.95(4)%. These three metrics indicate that nuclear spins in silicon are approaching the performance demanded in fault-tolerant quantum processors. We then demonstrate entanglement between the two nuclei and the shared electron by producing a Greenberger-Horne-Zeilinger three-qubit state with 92.5(1.0)% fidelity. Because electron spin qubits in semiconductors can be further coupled to other electrons or physically shuttled across different locations, these results establish a viable route for scalable quantum information processing using donor nuclear and electron spins.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Highly Selective Oxygen Reduction to Hydrogen Peroxide on a Carbon-Supported Single-Atom Pd Electrocatalyst

Selective electrochemical two-electron oxygen reduction is a promising route for renewable and on-site H 2 O 2 generation as an alternative to the anthraquinone process. In this study, we report a high-performance nitrogen-coordinated single-atom Pd electrocatalyst, which is derived from Pd-doped zeolitic imidazolate frameworks (ZIFs) through one-step thermolysis. High-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) combined with X-ray absorption spectroscopy verifies atomically dispersed Pd atoms on nitrogen-doped carbon (Pd-NC). The single-atom Pd-NC catalyst exhibits excellent electrocatalytic performance for two-electron oxygen reduction to H 2 O 2 , which shows ~95% selectivity toward H 2 O 2 and an unprecedented onset potential of ~0.8 V versus revisable hydrogen electrode (RHE) in 0.1 M KOH. Density functional theory (DFT) calculations demonstrate that the Pd-N 4 catalytic sites thermodynamically prefer *–O bond breaking to O–O bond breaking, corresponding to a high selectivity for H 2 O 2 production. This work provides a deep insight into the understanding of the catalytic process and design of high-performance 2e– ORR catalysts.

36 MATERIALS SCIENCE↗

Revisiting W–ZrC interfaces: A first principles study

We investigate W–ZrC interfaces using first-principles calculations based on the density functional theory. There have been theoretical and experimental studies exploring W–ZrC interfaces, however, the debate regarding the most stable interface continues to persist. In this study, we systematically simulated various W–ZrC interfaces merging W and ZrC surfaces with different orientations. Subsequently, we evaluated their stabilities and explained the corresponding stabilities in terms of the nature of bonding and charge-transfer processes at the interface. We find ZrC(111)–W(110) is the most stable interface with higher adhesive energy than the other interfaces. The additional stability associated with the ZrC(111)–W(110) results from significant interface reconstruction. Three layers of W and ZrC adjacent to the interface are involved in the charge-transfer process leading to stronger ionic bonds in ZrC(111)–W(110) as compared to the other potential candidate: ZrC(100)–W(100). The C and W atoms are found to be displaced from their symmetric position during the reconstruction process at the interface to facilitate stronger bonds with shorter W–C and W–Zr bonds in ZrC(111)–W(110) as compared to ZrC(100)–W(100). This leads to stronger covalent bonds in ZrC(111)–W(110) than that in ZrC(100)–W(100). Therefore, we conclude that the stronger covalent and ionic forces in ZrC(111)–W(110) than those in ZrC(100)–W(100) are responsible for making ZrC(111)–W(110) to be the most stable interface. In conclusion, this study addresses the long-standing question of the most stable W–ZrC interface and derives a number of implications for other W-transition metal carbide interfaces which are potential candidates for improving the mechanical properties of plasma facing materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Monte Carlo Computational Modeling of the Energy Dependence of Atomic Oxygen Undercutting of Protected Polymers

A Monte Carlo computational model has been developed which simulates atomic oxygen attack of protected polymers at defect sites in the protective coatings. The parameters defining how atomic oxygen interacts with polymers and protective coatings as well as the scattering processes which occur have been optimized to replicate experimental results observed from protected polyimide Kapton on the Long Duration Exposure Facility (LDEF) mission. Computational prediction of atomic oxygen undercutting at defect sites in protective coatings for various arrival energies was investigated. The atomic oxygen undercutting energy dependence predictions enable one to predict mass loss that would occur in low Earth orbit, based on lower energy ground laboratory atomic oxygen beam systems. Results of computational model prediction of undercut cavity size as a function of energy and defect size will be presented to provide insight into expected in-space mass loss of protected polymers with protective coating defects based on lower energy ground laboratory testing.

Banks, Bruce A.↗

Defect formation and bending properties in graphite under He atom implantation investigated by molecular dynamics method

The formation and evolution of radiation defects and their effects on bending property of a single graphite under low energy helium atom implantation have been studied at atomic scale through molecular dynamics simulations. Various simple interstitial and vacancy defects are observed during the implantation process, which is a function of incident energy and cross section of helium-carbon interaction. Large defects are observed after continuous helium atom implantations. The effects of incident energy on the density, size and distribution of defects are analyzed in detail. Furthermore, the kinetic evolution process of radiation defects at different annealing temperatures have also been simulated, including the migration, aggregation, transformation, coalescence, and self-healing. Here, the large defect clusters, crossing several carbon layers, have been confirmed to be the primary reasons that affect the bending property of graphite. All these results provide a new understanding for further applications of graphite in nuclear reactors.

Atomic implantation↗

Plastic scintillators in coincidence for the study of multi-particle production of sea level cosmic rays in dense medium

Cosmic ray particles at sea level penetrate a thick layer of dense medium without appreciable interaction. These penetrating particles are identified with muons. The only appreciable interaction of muons are by knock on processes. A muon may have single, double or any number of knock on with atoms of the material so that one, two, three or more particles will come out from the medium in which the knock on processes occur. The probability of multiparticle production is expected to decrease with the increase of multiplicity. Measurements of the single, double, and triple particles generated in a dense medium (Fe and Al) by sea level cosmic rays at 22.42 N. Lat. and 114.20 E. Long. (Hong Kong) are presented using a detector composed of two plastic scintillators connected in coincidence.

Chuang, L. S.↗

Morphology-controlled transformation of Cu@Au core-shell nanowires into thermally stable Cu 3 Au intermetallic nanowires

Multimetallic nanowires with long-range atomic ordering hold the promise of unique physicochemical properties in many applications. Here we demonstrate the synthesis and study the stability of Cu 3 Au intermetallic nanowires. The synthesis is achieved by using Cu@Au core-shell nanowires as precursors. With appropriate Cu/Au stoichiometry, the Cu@Au core-shell nanowires are transformed into fully ordered Cu 3 Au nanowires under thermal annealing. Thermally-driven atom diffusion accounts for this transformation as revealed by X-ray diffraction and electron microscopy studies. The twin boundaries abundant in the Cu@Au core-shell nanowires facilitate the ordering process. The resulting Cu 3 Au intermetallic nanowires have uniform and accurate atomic positioning in the crystal lattice, which enhances the nobility of Cu. No obvious copper oxides are observed in fully ordered Cu 3 Au nanowires after annealing in air at 200 °C, a temperature that is much higher than those observed in Cu@Au core-shell and pure Cu nanowires. This work opens up an opportunity for further research into the development and applications of intermetallic nanowires.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Fe-single-atom catalyst nanocages linked by bacterial cellulose-derived carbon nanofiber aerogel for Li-S batteries

Li-S battery (LSB) is promising for achieving high capacity. Still, its development is hindered by the complex redox process with sluggish kinetics and particularly the resulting lithium polysulfides (LiPS) shuttle effects. Single-atom catalysts (SACs), with their maximized atom utilization, could effectively chemisorb soluble LiPSs and expedite the sulfide conversion reaction kinetics. Here we report incorporating Fe single metal atom catalyst (Fe-SAC) in the sulfur cathode design and its electrocatalytic effects. Fe-doped ZIF-8 nanocages were introduced into a cheap biomass bacteria cellulose. A pyrolysis process converted them into an aerogel structure with Fe-SAC-functionalized N-doped carbon nanocages linked by a carbon nanofiber network (FeSA-NC@CBC), which was applied as a scaffold to fabricate freestanding and binder-free sulfur cathodes. He we conducted electrochemical measurements to reveal Fe-SAC functions including lowering energy barriers for S 8 reduction to liquid-phase LiPSs and further to solid-phase Li 2 S 2 /Li 2 S and accelerating Li 2 S 2 /Li 2 S nucleation and deposition, as corroborated by our theoretical calculation results. Benefiting from the synergistic effects of highly active Fe-SAC and three-dimensional conductive network, the sulfide reaction kinetics is improved, which can diminish LiPS shuttle effects and therefore improve LBS rate performance and cycling stability. Accordingly, the fabricated FeSA-NC@CBC composite cathode delivers an excellent rate capability at 2C with a reversible capacity of 840 mAh/g and a long-term cyclic stability of 800 mAh/g at 1C after 500 cycles.

25 ENERGY STORAGE↗

Manufacturing Oxide Dispersion-Strengthened (ODS) Steel Fuel Cladding Tubes Using the Cold Spray Process

The cold spray materials deposition process has been explored for manufacturing oxide dispersion-strengthened (ODS) steel fuel cladding tubes. Gas-atomized 14YWT ODS steel powder was used as the feedstock material. A parametric investigation of the cold spray process involving substrate materials of various hardnesses, gas preheat temperatures, and carrier gas compositions was performed to gain the highest quality deposit. The high-velocity impact of the powder on the substrate led to dissolution of discrete oxide nanoparticles, which subsequently reprecipitated during postdeposition annealing at high temperatures. The tubes were manufactured by deposition on an Al-alloy mandrel substrate and subsequent chemical dissolution of the substrate. A 204-mm-long and 1-mm-thick ODS steel cladding tube was successfully manufactured. The grain growth and distribution of oxide nanoparticles in ferritic steel matrix were identified at elevated temperatures. In general, the cold spray process holds considerable promise for rapid, cost-effective manufacturing of ODS steel cladding tubes.

36 MATERIALS SCIENCE↗

Effect of Powder Shape and Size on Rheological, Thermal, and Segregation Properties of Low-Pressure Powder Injection Molding Feedstocks

Optimization of molding parameters at different filling stages requires that the characteristics of low-viscosity feedstocks must be properly known. In this study, the influence of the particle size (3, 7, and 12 μm) and powder morphology (gas- and water-atomized) was quantified using different feedstock formulations based on a 17-4 PH stainless steel powder, all combined with the same binder system. The specific heat capacity, viscosity, and segregation levels were assessed using a differential scanning calorimeter, a rotational rheometer, and a thermogravimetric analyzer, respectively. It was then shown that the feedstock prepared with the gas-atomized powder exhibits a higher specific heat capacity value when compared to a water-atomized powder (i.e., Cp varying from 0.6 to 0.3 J/g K, respectively). It was also shown that the feedstock viscosity profiles and the intensity of segregation both depend significantly on the powder shape and size used in the feedstock formulation. For short processing times (e.g., < 1 min spent in molten state), a feedstock formulated with coarse gas-atomized powder can be considered to be the best candidate for an injection process because its viscosity and segregation potential are relatively low (with a viscosity varying from 0.5 to 2 Pa s, and a volume fraction of powder close to 60 vol.%). Following this, the moldability index was used to predict that coarser water-atomized powder (i.e., 12 versus 7 μm) will not have a significant effect on the molding properties, and can be seen as a potential means of decreasing shrinkage during sintering without impacting the injection properties. For very long processing times, the magnitude of segregation remains insignificant for feedstock formulated with fine powder (i.e., a volume fraction of powder remaining close to 60 vol.%). However, this important gain (i.e., no segregation) comes with a significant increase in viscosity varying from 2 to 10 Pa s, resulting in a decrease in the molding properties.

36 MATERIALS SCIENCE↗

Identification of the glassy state in nanoparticles by transmission electron microscopy

Identification of amorphous phases in nanoparticles by atomic-resolution transmission electron microscopy (TEM) requires analyses such as tilt-angle-dependent TEM imaging and single-nanoparticle electron diffraction, rather than relying on a single TEM image. Here, the disordered structures of amorphous nanoparticles offer unique atomic configurations and properties that differ from the properties of their crystalline counterparts. These characteristics have motivated the exploration of such materials for mechanical, sensing and catalytic applications. In addition, the formation of amorphous metal nanoparticles is an important endeavour to understand the process of vitrification and the nature of the glassy state. Atomic-resolution transmission electron microscopy (TEM) is increasingly being used as a tool for characterizing structures of nanoparticles produced by vitrification. In this Comment, we discuss the pitfalls of using TEM for ascertaining whether nanoparticles are amorphous. We also make recommendations of best practices.

Alcorn, Francis M. [Sandia National Laboratories (↗

Ultra-High Resolution Elemental/Isotopic Mass Spectrometry (m/?m> 1,000,000): Coupling of the Liquid Sampling-Atmospheric Pressure Glow Discharge with an Orbitrap Mass Spectrometer for Applications in Biological Chemistry and Environmental Analysis

Many fundamental questions of astrophysics, biochemistry, and geology rely on the ability to accurately and precisely measure the mass and abundance of isotopes. Taken a step further, the capacity to perform such measurements on intact molecules provides insights into processes in diverse biological systems. Described here is the coupling of a combined atomic and molecular (CAM) ionization source, the liquid sampling-atmospheric pressure glow discharge (LS-APGD) microplasma, with a commercially available ThermoScientific Fusion Lumos mass spectrometer. Demonstrated for the first time is the ionization and isotopically-resolved fingerprinting of a long-postulated, but never mass-spectrometrically observed, bi-metallic complex Hg:Se-cysteine. Such a complex has been implicated as having a role in observations of Hg detoxification by selenoproteins/amino acids. Demonstrated as well is the ability to mass spectrometrically-resolve the geochronologically important isobaric 87Sr and 87Rb species (?m ~ 0.3 mDa, mass resolution m/?m ? 1,700,000). The mass difference in this case reflects the beta-decay of the 87Rb to the stable Sr isotope. These two demonstrations highlight what may be a significant change in bioinorganic and atomic mass spectrometry, with impact expected across a broad spectrum of the physical, biological and geological sciences.

Hoegg, Edward D.↗

Spatiotemporal characterization of cerium monoxide in laser ablation plasmas using spectrally-resolved fast-gated imaging

The impact of oxidation chemistry on the emission characteristics and spatial structure of laser-produced Ce metal plasmas was investigated using laser-induced breakdown spectroscopy (LIBS) and time-resolved fast-gated imaging employing narrowband optical filters. Images of the plasma emission show that CeO coexists with atomic species in the periphery and vortex ring of the plasma plume. Image processing was also applied to combine independent monochromatic images of the plasma emission into a single merged image, culminating in a timelapse on the spatiotemporal evolution of atomic and molecular species within the plasma plume. The formation of CeO species was observed to proceed faster for plasmas generated in atmospheres containing larger concentrations of oxygen based on ratios of CeO-to-atomic emission intensities. Furthermore, these same ratios were shown to plateau and decrease at later times (≥25 μs), potentially indicating the depletion of CeO number densities in the plasma as the monoxide undergoes reactions to form higher polyatomic oxides. Altogether, these results provide fundamental insights into the chemical dynamics and intermixing between plasma-gas species in laser ablation cerium plasmas, advancing our understanding on optical signatures of nuclear-relevant materials to enable in-field measurement capabilities.

47 OTHER INSTRUMENTATION↗

Facet-dependent growth and dissolution of hematite resulting from autocatalytic interactions with Fe(II) and oxalic acid

The ability to simultaneously monitor the flux of iron atoms within the solution and solid phases can provide considerable insight into mechanisms of iron oxide mineral transformations. The autocatalytic interaction between hematite and Fe(II)-oxalate has long been of interest for its environmental and industrial relevance. In this study we take advantage of iron isotopic labelling and mass-sensitive imaging at the single particle scale to determine how changes in solution composition correlate with the morphologic evolution of faceted, micrometer-sized hematite platelets. Net dissolution is confirmed through analyses of aqueous iron chemistry, as well as by quantitative atomic force microscopy. Isotopic mapping techniques show that Fe(II) readily adsorbs to (001) and (012) surfaces in the absence of oxalate, but when oxalate is present selective dissolution of the (001) surface prevails and 57Fe deposition via recrystallization is not observed. Comparison between particle microtopographies following reaction with Fe(II), oxalate, and Fe(II)-oxalate show substantially different behavior, consistent with distinct mechanisms of interaction with hematite surfaces. The extensive characterization conducted on the coupled solution/solid dynamics in this system provides new insight for distinguishing crystal growth, dissolution, and recrystallization processes.

Taylor, Sandra D. [BATTELLE (PACIFIC NW LAB)]↗

The surface properties of fluorinated polyimides exposed to VUV and atomic oxygen

The effect of atomic oxygen flux and VUV radiation alone and in combination on the surface of fluorinated polyimide films was studied using XPS spectroscopy. Exposure of fluorinated polyimides to VUV radiation alone caused no observable damage to the polymer surface, while an atomic oxygen flux resulted in substantial oxidation of the surface. On the other hand, exposure to VUV radiation and atomic oxygen in combination caused extensive oxidation of the polymer surface after only 2 minutes of exposure. The amount of oxidized carbon on the polymer surface indicated that there is aromatic ring opening oxidation. The changes in the O1s/C1s, N1s/C1s, and F1s/C1s ratios suggested that an ablative degradation process is highly favorable. A synergistic effect of VUV radiation in the presence of atomic oxygen is clearly evidenced from the XPS study. The atomic oxygen could be considered as the main factor in the degradation process of fluorinated polyimide films exposed to a low earth orbit environment.

Forsythe, John S.↗

Inception of electronic damage of matter by photon-driven post-ionization mechanisms

“Probe-before-destroy” methodology permitted diffraction and imaging measurements of intact specimens using ultrabright but highly destructive X-ray free-electron laser (XFEL) pulses. The methodology takes advantage of XFEL pulses ultrashort duration to outrun the destructive nature of the X-rays. Atomic movement, generally on the order of >50 fs, regulates the maximum pulse duration for intact specimen measurements. In this contribution, we report the electronic structure damage of a molecule with ultrashort X-ray pulses under preservation of the atoms' positions. A detailed investigation of the X-ray induced processes revealed that X-ray absorption events in the solvent produce a significant number of solvated electrons within attosecond and femtosecond timescales that are capable of coulombic interactions with the probed molecules. The presented findings show a strong influence on the experimental spectra coming from ionization of the probed atoms' surroundings leading to electronic structure modification much faster than direct absorption of photons. This work calls for consideration of this phenomenon in cases focused on samples embedded in, e.g., solutions or in matrices, which in fact concerns most of the experimental studies.

43 PARTICLE ACCELERATORS↗

MgO-Al2O3-ZrO2 Amorphous Ternary Composite: A Dense and Stable Optical Coating

The process-parameter-dependent optical and structural properties of MgO-Al2O3-ZrO2 ternary mixed-composite material were investigated. Optical properties were derived from spectrophotometric measurements. The surface morphology, grain size distributions, crystallographic phases, and process- dependent material composition of films were investigated through the use of atomic force microscopy, x-ray diffraction analysis, and energy-dispersive x-ray analysis. Energy-dispersive x-ray analysis made evident the correlation between the optical constants and the process-dependent compositions in the films. It is possible to achieve environmentally stable amorphous films with high packing density under certain optimized process conditions.

Shaoo, Naba K.↗

Gaussian approximation potential for amorphous Si : H

Hydrogenation of amorphous silicon (a–Si : H) is critical for reducing defect densities, passivating midgap states and surfaces, and improving photoconductivity in silicon-based electro-optical devices. Modeling the atomic-scale structure of this material is critical to understanding these processes, which in turn is needed to describe c–Si/a–Si : H heterojunctions that are at the heart of modern solar cells with world-record efficiency. Density functional theory (DFT) studies achieve the required high accuracy but are limited to moderate system sizes of 100 atoms or so by their high computational cost. Simulations of amorphous materials have been hindered by this high cost because large structural models are required to capture the medium-range order that is characteristic of such materials. Empirical potential models are much faster, but their accuracy is not sufficient to correctly describe the frustrated local structure. Data-driven, machine-learned interatomic potentials have broken this impasse and have been highly successful in describing a variety of amorphous materials in their elemental phase. Here, we extend the Gaussian approximation potential (GAP) for silicon by incorporating the interaction with hydrogen, thereby significantly improving the degree of realism with which amorphous silicon can be modeled. We show that our Si : H GAP enables the simulation of hydrogenated silicon with an accuracy very close to DFT but with computational expense and run times reduced by several orders of magnitude for large structures. Here, we demonstrate the capabilities of the Si : H GAP by creating models of hydrogenated liquid and amorphous silicon and showing that their energies, forces, and stresses are in excellent agreement with DFT results, and their structure as captured by bond and angle distributions are in agreement with both DFT and experiments.

36 MATERIALS SCIENCE↗