Search NASA⌕ Search

SEARCH · Search NASA

Results for “etch”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Effects of chemo-mechanical polishing on CdZnTe X-ray and gamma-ray detectors

Here, mechanically polishing cadmium zinc telluride (CdZnTe) wafers for x-ray and gamma-ray detectors often is inadequate in removing surface defects caused by cutting them from the ingots. Fabrication-induced defects, such as surface roughness, dangling bonds, and nonstoichiometric surfaces, often are reduced through polishing and etching the surface. In our earlier studies of mechanical polishing with alumina powder, etching with hydrogen bromide in hydrogen peroxide solution, and chemomechanical polishing with bromine–methanol–ethylene glycol solution, we found that the chemomechanical polishing process produced the least surface leakage current. In this research, we focused on using two chemicals to chemomechanically polish CdZnTe wafers after mechanical polishing, viz. bromine–methanol–ethylene glycol (BME) solution, and hydrogen bromide (HBr) in a hydrogen peroxide and ethylene–glycol solution. We used x-ray photoelectron spectroscopy (XPS), current–voltage (I–V) measurements, and Am-241 spectral response measurements to characterize and compare the effects of each solution. The results show that the HBr-based solution produced lower leakage current than the BME solution. Results from using the same chemomechanical polishing solution on two samples confirmed that the surface treatment affects the measured bulk current (a combination of bulk and surface currents). XPS results indicate that the tellurium oxide to tellurium peak ratios for the mechanical polishing process were reduced significantly by chemomechanical polishing using the BME solution (78.9% for Te 3d 5/2 O 2 and 76.7% for Te 3d 3/2 O 2 ) compared with the HBr-based solution (27.6% for Te 3d 5/2 O 2 and 35.8% for Te 3d 3/2 O 2 ). Spectral response measurements showed that the 59.5-keV peak of Am-241 remained under the same channel number for all three CdZnTe samples. While the BME-based solution gave a better performance of 7.15% full-width at half-maximum (FWHM) compared with 7.59% FWHM for the HBr-based solution, the latter showed a smaller variation in performance of 0.39% FWHM over 7 days compared with 0.69% for the BME-based solution.

36 MATERIALS SCIENCE↗

Bilayer self-assembly on a hydrophilic, deterministically nano-patterned surface

We present measurements of the in-situ, microscopic architecture of a self-assembled bilayer at the interface between a regularly nano-patterned surface and an aqueous sub-phase using neutron reflectometry. The substrate is patterned with a rectangular array of nano-scaled holes. Because of the high quality of the pattern, using neutron reflectometry, we are able to map the surface-normal density distribution of the patterned silicon, the penetration of water into the pattern, and the distribution of a deposited film inside and outside of the etched holes. In this study, 1,2-dilauroyl-sn-glycero-3-phosphocholine (DLPC) single bilayers were deposited on the hydrophilic patterned surface. For bilayers deposited either by vesicle fusion (VF) or by the Langmuir Schaefer (L-S) technique, the most consistent model found to fit the data shows that the lipids form bilayer coatings on top of the substrate as well as the bottoms of the holes in an essentially conformal fashion. However, while there is a single bilayer on the unetched silicon surface, the lipids coating the bottoms of the holes form a complex bimodal structure consistent with a rough surface produced by the etching process. This study provides insight into film transfer both outside and inside regular nano-patterned features.

Smith, Gregory Scott↗

Compositional effects in Ag 2 ZnSnSe 4 thin films and photovoltaic devices

Ag 2 ZnSnSe 4 (AZTSe) is a relatively new n-type photovoltaic (PV) absorber material which has recently demonstrated a conversion efficiency of ~5% in a Schottky device architecture. To date, little is known about how the influence of composition on AZTSe material properties and the resulting PV performance. In this study, the Ag/Sn ratio is shown to be critical in the controlling grain growth, non-radiative recombination, and the bulk defect structure of the absorber. Insufficient Ag (relative to Zn and Sn) results in small grains, low photoluminescence intensities, and band gap narrowing, possibly due to an increase in the bulk defect density. Additionally, etching the AZTSe films in KCN prior to junction formation is found to be important for achieving reproducible efficiencies. Surface analysis using Auger Nanoprobe Microscopy analysis reveals that a KCN etch can selectively remove potentially harmful Ag-rich secondary phases, therefore improving the MoO 3 /AZTSe junction quality. Moreover, grain boundaries in AZTSe are found to be enriched in Sn and O following KCN; the role this oxide plays in surface passivation and junction formation has yet to be determined.

36 MATERIALS SCIENCE↗

Temperature-dependent dynamic fouling on superhydrophobic and slippery nonwetting copper surfaces

Bioinspired, superhydrophobic and slippery liquid infused surfaces that offer nonwetting characteristics have been explored in recent years for fouling mitigation. However, most of the studies are in the context of biofouling or under static immersion at ambient temperature conditions that are not reflective of the dynamic flow environment in practice. This article presents, for the first time, a systematic study of dynamic fouling of superhydrophobic (SHS) and slippery lubricant-infused surfaces (LIS) over a range of flow and temperature conditions. In this work, copper metallic surfaces were textured via electrodeposition or etching and further functionalized to achieve SHS and, additionally, infiltrated with a lubricant to fabricate LIS. The nonwetting surfaces were studied for their fouling behavior in a rotating Couette flow of a supersaturated calcium sulfate solution at different rotational speed and temperature. Fouling mineral mass accumulation on the different surfaces was measured as a function of time over a period of days using inductively coupled plasma mass spectroscopy and the fouled surfaces were investigated using scanning electron microscopy. Both SHS and LIS showed superior anti-scaling performance at all ranges of variables. An analytical Hill-Langmuir model is presented, for the first time, to describe the time evolution of scaling within 20% accuracy over the range of parameters studied. The study is the first to juxtapose two surface texturing methods, electrodeposition and etching, and two nonwetting surface types, SHS and LIS, subject to a common suite of experiments to elucidate fundamental understanding of mineral fouling on nonwetting surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A comparative study of mechanical and chemical durability of non-wetting superhydrophobic and lubricant-infused surfaces

Fabrication of bioinspired non-wetting superhydrophobic surfaces (SHS) and lubricant-infused surfaces (LIS) has been studied extensively on a variety of materials. In contrast, durability of the surfaces exposed to harsh mechanical and chemical environments has been the subject of little attention. This study considers the mechanical and chemical durability of SHS and LIS copper surfaces fabricated via facile electrodeposition and chemical etching methods. The as-fabricated surfaces demonstrate excellent non-wetting characteristics with water contact angle of 160° and sliding angle below 5°. The surfaces are subject to mechanical wear through scratch test and water jet impingement at 15 psi and 20 psi as well as accelerated corrosion following the ASTM-E407 standard. The performance of the electrodeposited and etched non-wetting surfaces is systematically assessed in terms of contact and sliding angles and corrosion rate in a simulated marine environment. All surfaces are shown to be robust to mechanical wear after scratch test, with excellent stability of contact and sliding angles, and up to two orders of magnitude reduced corrosion rate compared to bare copper surface. SHS retained steadfast non-wetting characteristics under high-pressure water jet tests compared to the other surfaces while LIS, regardless of texturing method, showed one to two orders of magnitude reduced corrosion rate compared to bare copper surface throughout water jet impingement and chemical durability tests. The study presents for the first time a systematic comparison of durability of SHS and LIS through a common set of fabrication and testing protocol and helps identify appropriate non-wetting surfaces and fabrication methods based on the use environment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hierarchically porous electrospun carbon nanofiber for high-rate capacitive deionization electrodes

Capacitive deionization (CDI) is a promising technology that has gained interest for the desalination of brackish water. Hierarchically porous carbons are commonly used as electrodes for CDI due to their high surface areas and controlled pore size distributions that maximize ion adsorption capacity and rate. Electrospinning is an effective way of generating carbon nanofibers with high inter-fiber macroporosity that can be further modified to improve surface area, total pore volume, and pore size distribution. This work describes the use of sacrificial mesopore formers in tandem with a micropore etching technique to induce hierarchical porosity in electrospun fibers. Mesopores are formed via the dissolution of silica nanoparticles that are introduced into the fibers during the electrospinning step. After mesopore formation, micropores are etched into the resulting surface through KOH impregnation and thermal activation. This sequential technique creates a hierarchical network of pores from the inherent macroporosity of the fiber network, to the mesopores, and finally micropores to simultaneously maximize surface area and accessibility. Micropore formation is optimized to maximize specific surface area while maintaining physical integrity of the fibers. Further, the combination of mesopores and micropores enables fast ion adsorption rates and capacity. Carbon fiber electrodes fabricated in this method achieve specific surface areas exceeding 1400 m 2 g -1 , with pore volumes exceeding 1.0cc g -1 . The pore size distributions are highly controlled, with 80% of total pore volume coming from pores <20nm in radius. In 500 ppm constant voltage CDI tests, these fiber electrodes obtain a salt adsorption capacity of over 14 mg g -1 at a salt adsorption rate of ~4mg g -1 min -1 , showcasing the high capacity matched with high rate of these easily fabricated, inexpensive materials.

36 MATERIALS SCIENCE↗

Atomic structure and grain shape evolution of nanodiamond during annealing in oxidizing atmosphere from neutron diffraction and MD simulations

In this work, real space pair-distribution function (PDF) analysis in conjunction with molecular dynamics (MD) simulations was applied to characterize crystal structure, shape and surface structure of diamond nanoparticles annealed in air up to 880 °C. MD simulated models of individual nanodiamond particles of various shapes and sizes were used to calculate theoretical radial distribution functions G(r) for powders with different grain size distributions. The calculated curves, showing distinct differences for the explored parameter space, were compared to the experimental G(r) functions obtained from neutron scattering for annealed detonated nanodiamond samples in a search for a model best describing the actual powders. It was found that as-synthesized nanodiamond grains are terminated by equally abundant (100), (110) and (111) crystallographic faces and their structure does not change upon annealing in air up to 280 °C. The shape and size of grains annealed above 480 °C changes due to surface etching. The etching rate differs between crystals faces and depends on temperature, resulting in the observed differences in grain shape. Below 680 °C the share of the (110) facets gradually increases and at 680 °C the grains become rhombic dodecahedra terminated solely by (110) surfaces. Further increase of the annealing temperature promotes formation of (111) surfaces and at 880 °C the preferred grain shape becomes an octahedron terminated by a variant of (111) surfaces possessing three dangling sp3 bonds per atom. At lower temperatures all grains become smaller and the size distribution moves towards the lower values. Furthermore, as the annealing temperature increases, the smallest grains disappear entirely and the average grain size grows back.

36 MATERIALS SCIENCE↗

Effect of pinholes in Nb 4 C 3 MXene sheets on its electrochemical behavior in aqueous electrolytes

Two-dimensional (2D) niobium carbide, Nb 4 C 3 T x (T x : O, OH, and F), a representative member of the 43 MXene structural motif, has shown promising electrochemical performance in acidic electrolytes. The capacitive performance of Nb 4 C 3 T x in neutral aqueous electrolytes has been reported as moderate, but little effort has been made to improve it. In this paper, we report a method to introduce nanopores (pinholes) in Nb 4 C 3 T x MXene flakes by adjusting the etching time. The pinholes generated during the etching process improve ion diffusion pathways, which are otherwise hindered by the restacking of the 2D flakes. The “holey Nb 4 C 3 T x ” shows a 50 % improved rate capability at charge/discharge time scales of 1–2 s in 1 M Li 2 SO 4 , Na 2 SO 4 , and (NH 4 ) 2 SO 4 electrolytes. Our strategy of controlling the permeability of Nb 4 C 3 T x sheets can potentially be applied to other MXenes, providing guidance for improving the capacitance and rate capability of 2D materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanoengineering of 2D MBenes for energy storage applications: A review

2D transition metal borides (MBenes), a flourishing member of the 2D nanomaterial family, show great potential in a number of study areas. MBenes have received increasing attention thanks to their excellent electrical conductivity, structural and mechanical properties, and chemical stability, which have captivated researchers and sparked further exploration. Extensive theoretical and experimental investigations have unveiled its remarkable potential as electrode materials for electrochemical storage applications, making MBenes a subject of great interest. Despite the growing interest and numerous studies conducted, there is a lack of a comprehensive and systematic appraisal of MBenes' applications in electrochemical energy storage systems. Here, in light of this, firstly, we provide an overview of the current progress in the fabrication and characterization of MAB phases and MBenes. For the synthesis of MBenes, the following fabrication techniques were discussed; liquid-phase exfoliation, solid-state mechanical exfoliation, chemical vapor deposition, high-pressure chemical vapor deposition, microwave-assisted chemical etching, and ultrasound-assisted chemical etching methods. Then, we delve into the captivating potential of MBenes, specifically in the realm of energy storage applications and their role in enhancing electrochemical storage capabilities. The discussion encompasses their application in lithium-ion, lithium-sulfur, and lithium-selenide batteries, supercapacitors and other energy storage systems, providing a comprehensive perspective on their contributions to the energy landscape. Finally, a brief but significant summary of the challenges and opportunities of MBenes in practical applications was summarized. The present review provides a guide and scientific motivation for creating and developing advanced MBene-based nanomaterials, addressing the growing demand for cutting-edge energy storage systems.

25 ENERGY STORAGE↗

Enhanced internal condensation of R1233zd(E) on micro- and nanostructured copper and aluminum surfaces

In-tube condensation of refrigerants is an important process which affects thermal efficiency in many applications, ranging from refrigeration and air conditioning to electronics thermal management. In-tube heat transfer and pressure drop are important to heat exchanger sizing and design. Here, in this work, micro- and nanostructured surfaces are applied to the internal wetted areas of copper and aluminum mini-channels to enhance the condensation heat transfer coefficient of hydrofluorocarbon R1233zd(E) refrigerant. To achieve scalable nanomanufacturing, surfaces were uniformly structured by relying on hydrochloric acid etching of aluminum and chemical oxidation of copper. The etched aluminum surfaces exhibited a 150% increase in heat transfer coefficient compared to smooth aluminum channels at specific qualities, with a 66% heat transfer coefficient improvement for complete phase change from saturated vapor to saturated liquid. Copper oxide structures showed no discernable difference in thermal-hydraulic performance when compared to smooth copper channels. Critical dimensionless parameters governing the heat transfer enhancement were identified by varying the tube internal diameter (2.3 mm to 4.7 mm), refrigerant mass flux (50 to 300 kg/(m 2 ·s)), and refrigerant quality (0 to 1). The dimensionless parameters include the Bond number normalized to the condensate film thickness, and the Weber number modified by the vapor friction factor. The relatively small increase in pressure drop (< 10%) associated with these surface enhancements further supports the promise of this method. The scalable and cost-effective techniques used to create these aluminum microstructures may reduce manufacturing cost when compared with current enhancement approaches such as extrusion, drawing, and welding.

42 ENGINEERING↗

Bioinspired nonwetting surfaces for corrosion inhibition over a range of temperature and corrosivity

Applications of superhydrophobic (SHS) and lubricant infused surfaces (LIS) involve exposure to corrosive environments from the acidic to the basic, at a range of temperatures, that are not fully characterized. Here, we present for the first time a multifactorial study of the effects of surface fabrication method, surface modification, surface functionalization time, temperature and pH of the immersion medium on the corrosion performance of nonwetting copper surfaces. Bioinspired SHS and LIS fabricated using facile methods of etching and electrodeposition are systematically assessed using potentiodynamic polarization measurements for their corrosion resistance in saline solution (pH ≈7) over a temperature range 23–85°C. SHS and LIS are shown to exhibit diminished corrosion rate, by up to two orders of magnitude, compared to bare copper surface. An Arrhenius model is developed for the first time, describing the temperature- dependent corrosion rate of SHS and LIS. Electrochemical impedance spectroscopy is used to show that corrosion resistance of LIS is larger by three orders of magnitude in extremely acidic (pH = 1) and by an order magnitude in extremely alkaline (pH = 14) media compared to bare copper surface. Etched LIS are generally more resistant to corrosion compared to SHS at all temperatures with excellent microstructural durability.

42 ENGINEERING↗

Epitaxial Regrowth and Hole Shape Engineering for Photonic Crystal Surface Emitting Lasers (PCSELs)

In the present research, epitaxial regrowth by molecular beam epitaxy (MBE) is investigated as a fabrication process for void-semiconductor photonic crystal (PhC) surface emitting lasers (PCSELs). The PhC is patterned by electron beam lithography (EBL) and inductively coupled plasma (ICP) etch and is subsequently regrown by molecular beam epitaxy to embed a series of voids in bulk semiconductor. Experiments are conducted to investigate the effects of regrowth on air-hole morphology. The resulting voids have a distinct teardrop shape with the radius and depth of the etched hole playing a very critical role in the final regrown void’s dimensions. We demonstrate that specific hole diameters can encourage deposition to the bottom of the voids or to their sidewalls, allowing us to engineer the shape of the void more precisely as is required by the PCSEL design. A 980 nm InGaAs quantum well laser structure is optimized for low threshold lasing at the design wavelength and full device structures are patterned and regrown. An optically pumped PCSEL is demonstrated from this process.

36 MATERIALS SCIENCE↗

Using electron channeling contrast imaging to inform and improve the growth of high-efficiency GaAs solar cells on nanopatterned GaAs substrates

Patterned substrates provide opportunities for reducing the cost of high-efficiency III-V devices by incorporating mechanically weak layers beneficial for substrate reuse (e.g. by spalling). In this work, the functionality of electron channeling contrast imaging (ECCI) as a tool to efficiently understand and mitigate defect formation is exemplified by developing a process in which high-quality III-V material can be grown on nanopatterned GaAs substrates. Reactive ion etching used in the patterning process was found to damage the GaAs substrate surface, leading to the formation of stacking faults in the epitaxial material as observed by ECCI. Etching the patterned substrates in a 1 NH4OH: 1 H2O2: 50 DI H2O solution for 10 s prior to growth removed the substrate surface damage and stacking faults were no longer present. Growth of solar cell device structures initially produced samples with many macroscale flaws creating shunts in the devices, which complicated the assessment of material quality by device measurements. However, ECCI revealed that the epitaxial material surrounding macroscale flaws was free from any crystallographic defects such as stacking faults and threading dislocations. With this knowledge, we focused on refining the patterning process to eliminate the macroscale flaws. Solar cells were then grown on the improved nanopatterned substrates and exhibited device structures with defect densities less than 5 x 105 cm -2 and average conversion efficiency of 24.8%, nearly identical to devices grown on unpatterned epi-ready substrates (25.0%).

14 SOLAR ENERGY↗

Elucidating mechanisms of oxide growth and surface passivation on zinc thin film electrodes in alkaline solutions using the electrochemical quartz crystal microbalance

For this study, we utilized electrochemical quartz crystal microbalance to understand electrochemical passivation of the zinc electrode in alkaline media and subsequent oxide growth and stripping. The formation of native zinc oxide on a near pristine Zn surface upon contact with 1 M KOH electrolyte was observed. The surface was seen to roughen with time. During Zn dissolution, the measured mass-charge ratio corresponded to the removal of ZnO and not merely Zn. The mechanism of passivation was determined to be caused by electrochemical etching to form pores. The etching leads to a build-up of solid ZnO and Zn(OH) 2 due to electrochemical reactions on the surfaces of the pores. These reactions functionally close the pores off from the bulk. The cycle of Zn deposition and dissolution develops a porous network, which may be the origin of mossy Zn deposits that plague reversible Zn metal batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fabrication of carbon microcapsules containing silicon nanoparticles-carbon nanotubes nanocomposite by sol-gel method for anode in lithium ion battery

Carbon microcapsules containing silicon nanoparticles (Si NPs)-carbon nanotubes (CNTs) nanocomposite (Si-CNT-C) have been fabricated by a surfactant mediated sol-gel method followed by a carbonization process. Silicon nanoparticles-carbon nanotubes (Si-CNT) nanohybrids were produced by a wet-type beadsmill method. To obtain Si-CNT nanocomposites with spherical morphologies, a silica precursor (tetraethylorthosilicate, TEOS) and polymer (PMMA) mixture was employed as a structure-directing medium. Thus the Si-CNT/Silica-Polymer microspheres were prepared by an acid catalyzed sol-gel method. Then a carbon precursor such as polypyrrole (PPy) was incorporated onto the surfaces of pre-existing Si-CNT/silica-polymer to generate Si-CNT/Silica-Polymer-PPy microspheres. Subsequent thermal treatment of the precursor followed by wet etching of silica produced Si-CNT-C microcapsules. The intermediate silica/polymer must disappear during the carbonization and etching process resulting in the formation of an internal free space. The carbon precursor polymer should transform to carbon shell to encapsulate remaining Si-CNT nanocomposites. Therefore, hollow carbon microcapsules containing Si-CNT nanocomposites could be obtained (Si-CNT-C). The successful fabrication was confirmed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). These final materials were employed for anode performance improvement in lithium ion battery. The cyclic performances of these Si-CNT-C microcapsules were measured with a lithium battery half cell tests. - Graphical Abstract: Carbon microcapsules containing silicon nanoparticles (Si NPs)-carbon nanotubes (CNTs) nanocomposite (Si-CNT-C) have been fabricated by a surfactant mediated sol-gel method. Highlights: > Polymeric microcapsules containing Si-CNT transformed to carbon microcapsules. > Accommodate volume changes of Si NPs during Li ion charge/discharge. > Sizes of microcapsules were controlled by experimental parameters. > Lithium storage capacity and coulombic efficiency were demonstrated. > Use of sol-gel procedure as intermediate reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fabrication of Ag-Fe{sub 3}O{sub 4}/Fe superhydrophobic surface on galvanic sheet for its application

Highlights: • Ag-Fe{sub 3}O{sub 4}/Fe superhydrophobic surface (SHS) was fabricated on galvanic sheet. • The SHS has water contact angle of 165° and sliding angle of 2°. • The SHS has excellent properties of anti-icing, self-cleaning and catalysis. • This is an easy and cheap method to fabricate SHS on the galvanic sheet. - Abstract: Durable Ag-Fe{sub 3}O{sub 4}/Fe superhydrophobic surface (SHS) with dendritic structures on the galvanic sheet was obtained by chemical etching, deposition and following annealing process. The promising SHS showed fine superhydrophobicity having the water contact angle of 165° and dynamic sliding angle of 2°. Experimental results showed that the obtained SHS sample has excellent properties of anti-corrosion, catalysis, anti-icing, rolling-off and self-cleaning. The conditions of etching, chemical immersion, and annealing to obtain SHS were investigated. Chemical stability and durability of SHS were investigated via storage in air for ten months. The SHS as a catalyst showed long-term stability, catalytic activity, and reusability, as compared to the substrate of the un-annealed surface. It is an effortless and cheap method to fabricate SHS on the galvanic sheet for industrial applications. The SHS has a potential utilization in a diverse range of bio-medicines, chemistry, microfluidics fields, and electronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis of boron nitride nanotubes with SiC nanowire as template

Highlights: {yields} Boron nitride nanotubes (BNNTs) have been fabricated using SiC nanowires as template. {yields} SiC nanowires could be effectively etched out by the vapors decomposed from ammonia borane, leading to the formation of BNNTs. {yields} A template self-sacrificing mechanism is responsible for the formation of BNNTs. -- Abstract: A novel template method for the preparation of boron nitride nanotubes (BNNTs) using SiC nanowire as template and ammonia borane as precursor is reported. We find out that the SiC nanowires could be effectively etched out by the vapors decomposed from ammonia borane, leading to the formation of BNNTs. The as-prepared products are well characterized by means of complementary analytical techniques. A possible formation mechanism is disclosed. The method developed here paves the way for large scale production of BNNTs.

36 MATERIALS SCIENCE↗

The growth of benzophenone crystals by Sankaranarayanan-Ramasamy (SR) method and slow evaporation solution technique (SEST): A comparative investigation

Highlights: Black-Right-Pointing-Pointer Benzophenone single crystal was grown by Sankaranarayanan-Ramasamy method which has the sizes of 1060 mm length and 55 mm diameter for the first time. Black-Right-Pointing-Pointer The conventional and SR-grown benzophenone crystals were characterized and compared using HRXRD, etching, laser damage threshold, microhardness, UV-transmittance, birefringence and dielectric analysis. Black-Right-Pointing-Pointer The SR-grown benzophenone crystal has higher LDT, microhardness, transparency, dielectric permittivity, birefringence and lower FWHM, EPD, dielectric loss than the crystal grown by conventional method. Black-Right-Pointing-Pointer The probable reason for higher crystalline perfection in SR-grown crystal was discussed. -- Abstract: Longest unidirectional Left-Pointing-Angle-Bracket 1 0 0 Right-Pointing-Angle-Bracket benzophenone (BP) crystal having dimension of 1060 mm length and 55 mm diameter was grown by Sankaranarayanan-Ramasamy method. The growth rate was measured by monitoring the elevation of the crystal-solution interface at different temperatures. The high resolution X-ray diffraction and etching measurements indicate that the unidirectional grown benzophenone crystal has good crystalline perfection and less density of defects. The optical damage threshold of SEST and SR grown BP crystals has been investigated and found that the SR grown benzophenone crystal has higher laser damage threshold value than the conventional method grown crystal. Microhardness measurement shows that crystals grown by SR method have a higher mechanical stability than the crystals grown by SEST method. Dielectric permittivity and birefringence are high in SR grown crystal compared to SEST grown BP crystal. The UV-vis-NIR results show that SR method grown crystal exhibits 7% higher transmittance as against crystals grown by conventional method.

36 MATERIALS SCIENCE↗