Search NASA⌕ Search

SEARCH · Search NASA

Results for “flow improvers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Experimental Investigation of Separated and Transitional Boundary Layers Under Low-Pressure Turbine Airfoil Conditions

Modern low-pressure turbine airfoils are subject to increasingly stronger pressure gradients as designers impose higher loading in an effort to improve efficiency and to reduce part count. The adverse pressure gradients on the suction side of these airfoils can lead to boundary-layer separation, particularly under cruise conditions. Separation bubbles, notably those which fail to reattach, can result in a significant degradation of engine efficiency. Accurate prediction of separation and reattachment is hence crucial to improved turbine design. This requires an improved understanding of the transition flow physics. Transition may begin before or after separation, depending on the Reynolds number and other flow conditions, has a strong influence on subsequent reattachment, and may even eliminate separation. Further complicating the problem are the high free-stream turbulence levels in a real engine environment, the strong pressure gradients along the airfoils, the curvature of the airfoils, and the unsteadiness associated with wake passing from upstream stages. Because of the complicated flow situation, transition in these devices can take many paths that can coexist, vary in importance, and possibly also interact, at different locations and instances in time. The present work was carried out in an attempt to systematically sort out some of these issues. Detailed velocity measurements were made along a flat plate subject to the same nominal dimensionless pressure gradient as the suction side of a modern low-pressure turbine airfoil ('Pak-B'). The Reynolds number based on wetted plate length and nominal exit velocity, Re, was varied from 50;000 to 300; 000, covering cruise to takeoff conditions. Low, 0.2%, and high, 7%, inlet free-stream turbulence intensities were set using passive grids. These turbulence levels correspond to about 0.2% and 2.5% turbulence intensity in the test section when normalized with the exit velocity. The Reynolds number and free-stream turbulence level do not have a significant effect on the location of boundary-layer separation unless they are high enough to induce transition upstream of separation. The location and extent of the transition zone, in contrast, depend strongly on Re and TI. The beginning of reattachment closely follows the onset of transition. Under low free-stream turbulence conditions the boundary layer is laminar at separation and then begins to exhibit fluctuations in a finite frequency band in the shear layer over the separation bubble. These fluctuations are due to instability waves. The fluctuations grow in magnitude, higher harmonics are generated, and finally lead to a breakdown to turbulence. Transition begins in the shear layer, but quickly spreads to the near wall region and causes the boundary layer to reattach. The transition is rapid and the resulting turbulence contains a full range of high and low frequencies. Under high free-stream turbulence conditions, slowly growing low-frequency fluctuations are induced in the pretransitional boundary layer by the free-stream. The separation bubbles are considerably thinner than in the low TI cases, resulting in thinner boundary layers at the end of the test wall. At Re=50,000 and 100,000, the pre-transitional boundary layer separates at about the same location as in the low TI cases. Transition occurs through a bypass mode, begins upstream of the corresponding low-TI location, and proceeds in a manner similar to that of an attached boundary layer. Under high TI at Re=200,000 and 300,000, transition begins before separation. The boundary layer may separate, but if it does the separation bubble is very short and does not significantly affect the downstream development of the boundary layer. A comparison is made to previous work in a simulated cascade.

Hultgren, Lennart S.↗

Application of THEMIS Data to an Investigation of a Long Lava Flow in the Tharsis Montes Region of Mars

The Tharsis region of Mars has long been known for the numerous lava flows radiating from the Tharsis Montes shield volcanoes. A 480-km-long flow southwest of Ascraeus Mons has been the subject of previous investigations using Viking and MGS data. The new data currently being obtained with the Thermal Emission Imaging System (THEMIS) on the Mars Odyssey spacecraft can shed new light on the volcanology of Martian lava flows, illustrated in this paper by two THEMIS images of the previously studied flow near Ascraeus Mons. The lava flow examined is on the western flank of the topographic saddle between the Ascraeus Mons and Pavonis Mons shield volcanoes. Flow morphology in the dust-covered Tharsis region is revealed in exquisite detail in daytime IR and VIS images from THEMIS, which will aid in documentation and analysis of lava flow features on Mars and improve constraints for volcanic modeling.

Zimbelman, J. R.↗

Minnowbrook IV: 2003 Workshop on Transition and Unsteady Aspects of Turbomachinery Flows

On August 17 to 20, 2003, over 40 attendees participated in a workshop entitled "Minnowbrook IV.2003 Workshop on Transition and Unsteady Aspects of Turbomachinery Flows. Earlier themes focused on improving the understanding of late stage (final breakdown) of boundary layer transition. The specific engineering application of improving design codes for turbomachinery was encouraged by the attendance of representatives from gas turbine manufacturers. Written papers were not requested. Abstracts and copies of figures were the only written record of the workshop aside from specifically commissioned transcriptions of a workshop summary and the extensive working group reports, discussions, and summary that followed on the final morning of the workshop.

LaGraff, John E.↗

Slat Cove Unsteadiness Effect of 3D Flow Structures

Previous studies have indicated that 2D, time accurate computations based on a pseudo-laminar zonal model of the slat cove region (within the framework of the Reynolds-Averaged Navier-Stokes equations) are inadequate for predicting the full unsteady dynamics of the slat cove flow field. Even though such computations could capture the large-scale, unsteady vorticity structures in the slat cove region without requiring any external forcing, the simulated vortices were excessively strong and the recirculation zone was unduly energetic in comparison with the PIV measurements for a generic high-lift configuration. To resolve this discrepancy and to help enable physics based predictions of slat aeroacoustics, the present paper is focused on 3D simulations of the slat cove flow over a computational domain of limited spanwise extent. Maintaining the pseudo-laminar approach, current results indicate that accounting for the three-dimensionality of flow fluctuations leads to considerable improvement in the accuracy of the unsteady, nearfield solution. Analysis of simulation data points to the likely significance of turbulent fluctuations near the reattachment region toward the generation of broadband slat noise. The computed acoustic characteristics (in terms of the frequency spectrum and spatial distribution) within short distances from the slat resemble the previously reported, subscale measurements of slat noise.

Choudhari, Meelan M.↗

Simulation of an Isolated Tiltrotor in Hover with an Unstructured Overset-Grid RANS Solver

An unstructured overset-grid Reynolds Averaged Navier-Stokes (RANS) solver, FUN3D, is used to simulate an isolated tiltrotor in hover. An overview of the computational method is presented as well as the details of the overset-grid systems. Steady-state computations within a noninertial reference frame define the performance trends of the rotor across a range of the experimental collective settings. Results are presented to show the effects of off-body grid refinement and blade grid refinement. The computed performance and blade loading trends show good agreement with experimental results and previously published structured overset-grid computations. Off-body flow features indicate a significant improvement in the resolution of the first perpendicular blade vortex interaction with background grid refinement across the collective range. Considering experimental data uncertainty and effects of transition, the prediction of figure of merit on the baseline and refined grid is reasonable at the higher collective range- within 3 percent of the measured values. At the lower collective settings, the computed figure of merit is approximately 6 percent lower than the experimental data. A comparison of steady and unsteady results show that with temporal refinement, the dynamic results closely match the steady-state noninertial results which gives confidence in the accuracy of the dynamic overset-grid approach.

Lee-Rausch, Elizabeth M.↗

Conclusions and Recommendations

This chapter provides a brief wrap-up of the task group report and focuses on the overall conclusions and recommendations for future work for the CAWAPI and VFE-2 facets beyond the task group. The overall conclusion is that the Technology Readiness Level (TRL) of CFD solvers has been improved in predicting the flow-physics of vortex-dominated flows during the work of the task group, by having flight and wind-tunnel data available for comparison. Moreover, like all good scientific studies, this task group has identified flight conditions on the F-16XL airplane or wind-tunnel test conditions for a specific leading-edge radius on the 65 delta-wing model where the TRL still needs to be increased.

Lamar, John E.↗

Sub-Scale Testing and Development of the J-2X Fuel Turbopump Inducer

In the early stages of the J-2X upper stage engine program, various inducer configurations proposed for use in the fuel turbopump (FTP) were tested in water. The primary objectives of this test effort were twofold. First, to obtain a more comprehensive data set than that which existed in the Pratt & Whitney Rocketdyne (PWR) historical archives from the original J-2S program, and second, to supplement that data set with information regarding the cavitation induced vibrations for both the historical J-2S configuration as well as those tested for the J-2X program. The J-2X FTP inducer, which actually consists of an inducer stage mechanically attached to a kicker stage, underwent 4 primary iterations utilizing sub-scaled test articles manufactured and tested in PWR's Engineering Development Laboratory (EDL). The kicker remained unchanged throughout the test series. The four inducer configurations tested retained many of the basic design features of the J-2S inducer, but also included variations on leading edge blade thickness and blade angle distribution, primarily aimed at improving suction performance at higher flow coefficients. From these data sets, the effects of the tested design variables on hydrodynamic performance and cavitation instabilities were discerned. A limited comparison of impact to the inducer efficiency was determined as well.

Sargent, Scott R.↗

Unsteady Aerodynamic Modeling in Roll for the NASA Generic Transport Model

Reducing the impact of loss-of-control conditions on commercial transport aircraft is a primary goal of the NASA Aviation Safety Program. One aspect in developing the supporting technologies is to improve the aerodynamic models that represent these adverse conditions. Aerodynamic models appropriate for loss of control conditions require a more general mathematical representation to predict nonlinear unsteady behaviors. In this paper, a more general mathematical model is proposed for the subscale NASA Generic Transport Model (GTM) that covers both low and high angles of attack. Particular attention is devoted to the stall region where full-scale transports have demonstrated a tendency for roll instability. The complete aerodynamic model was estimated from dynamic wind-tunnel data. Advanced computational methods are used to improve understanding and visualize the flow physics within the region where roll instability is a factor.

Murphy, Patrick C.↗

Flow Quality Surveys in the Settling Chamber of the NASA Glenn Icing Research Tunnel (2011 Tests)

In 2011, the heat exchanger and refrigeration plant for NASA Glenn Research Center's Icing Research Tunnel (IRT) were upgraded. Flow quality surveys were performed in the settling chamber of the IRT in order to understand the effect that the new heat exchanger had on the flow quality upstream of the spray bars. Measurements were made of the total pressure, static pressure, total temperature, airspeed, and ow angle (pitch and yaw). These measurements were directly compared to measurements taken in 2000, after the previous heat exchanger was installed. In general, the flow quality appears to have improved with the new heat exchanger.

Steen, Laura E.↗

Flow Quality Surveys in the Settling Chamber of the NASA Glenn Icing Research Tunnel (2011 Tests)

In 2011, the heat exchanger and refrigeration plant for NASA Glenn Research Center's Icing Research Tunnel (IRT) were upgraded. Flow quality surveys were performed in the settling chamber of the IRT in order to understand the effect that the new heat exchanger had on the flow quality upstream of the spray bars. Measurements were made of the total pressure, static pressure, total temperature, airspeed, and flow angle (pitch and yaw). These measurements were directly compared to measurements taken in 2000, after the previous heat exchanger was installed. In general, the flow quality appears to have improved with the new heat exchanger.

Steen, Laura E.↗

Dynamic Responses of the Earth's Outer Core to Assimilation of Observed Geomagnetic Secular Variation

Assimilation of surface geomagnetic observations and geodynamo models has advanced very quickly in recent years. However, compared to advanced data assimilation systems in meteorology, geomagnetic data assimilation (GDAS) is still in an early stage. Among many challenges ranging from data to models is the disparity between the short observation records and the long time scales of the core dynamics. To better utilize available observational information, we have made an effort in this study to directly assimilate the Gauss coefficients of both the core field and its secular variation (SV) obtained via global geomagnetic field modeling, aiming at understanding the dynamical responses of the core fluid to these additional observational constraints. Our studies show that the SV assimilation helps significantly to shorten the dynamo model spin-up process. The flow beneath the core-mantle boundary (CMB) responds significantly to the observed field and its SV. The strongest responses occur in the relatively small scale flow (of the degrees L is approx. 30 in spherical harmonic expansions). This part of the flow includes the axisymmetric toroidal flow (of order m = 0) and non-axisymmetric poloidal flow with m (is) greater than 5. These responses can be used to better understand the core flow and, in particular, to improve accuracies of predicting geomagnetic variability in future.

secular variation↗

NASA AETC Test Technology Subproject

Funds directed to improve measurement capabilities (pressure, force, flow, and temperature), test techniques and processes, and develop technologies critical to meeting NASA research needs and applicable to a multitude of facilities. Primarily works by funding small ($40K - $400K) tasks which result in a demonstration or initial capability of a new technology in an AETC facility.TT research and development tasks are generally TRL 3-6; they should be things which work in small scale or lab environments but need further development for use in production facilities.TT differs from CA in its focus on smaller-scale tasks and on instrumentation. Technologies developed by TT may become CA projects in order be fully realized within a facility.

Bell, James↗

Application of Lattice Boltzmann and Navier-Stokes Methods to NASA's Wall Mounted Hump

Lattice Boltzmann (LB) based Large Eddy Simulation (LES), Reynolds-averaged Navier-Stokes (RANS) as well as hybrid RANS/LES methods within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework are applied to NASA's wall-mounted hump. Computational results are compared with experiments performed by Greenblatt et al. A detailed comparison between the accuracy and resolution requirements of the two approaches for turbulence resolving simulations, as well as the suitability of different grid paradigms (body-fitted curvilinear and block structured Cartesian) are presented. This test case is part of NASA's Revolutionary Computational Aerosciences (RCA) sub-project which addresses the technical challenge of predicting flow separation and reattachment accurately. Improvements in predictive accuracy by as much as 90% are demonstrated using LB as well as hybrid RANS/LES approaches compared to state-of-the-art steady state RANS simulations.

Lattice Boltzmann↗

Solving Two-Equation Turbulence Models With a Perspective on Solving Transport Equations

There are three principal objectives of this report. The first objective is to investigate frequently used two-equation models when solving the RANS equations. In this study, we consider the 2006Wilcox and the 2003 Menter Shear Stress Transport (SST) models. Also, a simple change of the Wilcox model is introduced to improve computational predictions for transonic flows. Computations for flows over two different airfoils are examined to compare these turbulence models. Effects on modeling the physics of each flow due to variations in the models, such as using either strainrate or vorticity in the turbulence production term, are considered and discussed. The second objective of this report is to not only explore but also evaluate the performance of the solution algorithm for the mean flow and the transport equations. The RANS and turbulence modeling equations aresolved in a weakly coupled manner with a diagonal implicit Runge-Kutta (DIRK) solution algorithm. Throughout this report, emphasis is given to reducing the residuals to machine zero in all flow calculations, so as to eliminate the error due to numerical integration of the discrete governing equations. The final objective is to provide a perspective on solving transport equations for turbulence modeling. Aspects of solving such stiff systems of equations, as well as various numerical difficulties and possible techniques to overcome them, are considered. Discussion is also provided concerning what is called ’numerical compatibility’, which is an essential requirement when designing a solution algorithm for solving transport equations.

turbulence modeling↗

Validation of Universal Cryogenic Flow Boiling Correlations in Thermal Desktop for Liquid Methane and Liquid Nitrogen

Future in-space cryogenic architectures will depend on the ability to accurately model various stages of cryogenic propellant transfer and storage. Currently there is a need for more accurate, direct cryogenic data-anchored models for various boiling phenomena. This paper presents the implementation and validation of recently developed universal cryogenic flow boiling correlations for saturated flow boiling heat transfer coefficients (HTC) and critical heat flux (CHF) into the Thermal Desktop (SINDA/FLUINT) modeling software. The correlations are validated against steady state cryogenic flow boiling historical heated tube cases from liquid nitrogen and liquid methane experiments covering a wide range of inlet conditions, mass flux, and heat flux. Overall, Thermal Desktop with the new universal cryogenic flow boiling correlations demonstrates significant improvement in predictive performance for both wall temperature and CHF location compared to the Thermal Desktop model with built-in correlations when both are compared to the data.

Mariano Mercado↗

Use of CFD in the Design of the 10- by 10-Foot Supersonic Wind Tunnel Characterization Array

At the 10- by 10-Foot Supersonic Wind Tunnel at the NASA Glenn Research Center, a future full test section characterization generated an ideal opportunity to design and build new characterization hardware to improve the understanding of the flow field, including flow quality, uniformity, and uncertainty in primary variables of interest. An array of flow sensing probes, referred to as the Characterization Array, was designed and built to replace 1960’s-era test section characterization hardware. Many references exist to guide wind tunnel characterization practitioners in the design of new hardware to properly measure various aspects of the flow within their wind tunnel facilities. Although reliable sources of information, these references tend to be over 30 years old and are not exhaustive. In scenarios where design decisions needed to be validated, computational simulations of the flow field around the characterization hardware were used. Decisions regarding probe location, probe spacing, and performance of various probes were justified using computational fluid dynamic simulations and rules-of-thumb from the legacy resources available in literature. This paper is intended to serve as an example of the benefits from integrating CFD into the design of wind tunnel hardware, particularly hardware for wind tunnel characterization.

CFD↗

Use of CFD in the Design of the 10- by 10-Foot Supersonic Wind Tunnel Characterization Array

At the 10- by 10-Foot Supersonic Wind Tunnel at the NASA Glenn Research Center, a future full test section characterization generated an ideal opportunity to design and build new characterization hardware to improve the understanding of the flow field, including flow quality, uniformity, and uncertainty in primary variables of interest. An array of flow sensing probes, referred to as the Characterization Array, was designed and built to replace 1960’s-era test section characterization hardware. Many references exist to guide wind tunnel characterization practitioners in the design of new hardware to properly measure various aspects of the flow within their wind tunnel facilities. Although reliable sources of information, these references tend to be over 30 years old and are not exhaustive. In scenarios where design decisions needed to be validated, computational simulations of the flow field around the characterization hardware were used. Decisions regarding probe location, probe spacing, and performance of various probes were justified using computational fluid dynamic simulations and rules-of-thumb from the legacy resources available in literature. This paper is intended to serve as an example of the benefits from integrating CFD into the design of wind tunnel hardware, particularly hardware for wind tunnel characterization.

CFD↗

Wall-Modeled LES of a Swept Wing with Leading-Edge Ice Using LAVA Curvilinear, Unstructured, and Cartesian Solvers

Wall-modeled large-eddy simulation (LES) of a swept wing with leading-edge ice build up is performed using three mesh paradigms and associated flow solvers and compared to experimental results. The study focuses on an 8.9% scale model of the CRM65 swept wing featuring both high-fidelity and smooth leading-edge ice shapes. The assessment is conducted using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) framework using the three actively supported meshing paradigms in LAVA: structured curvilinear overset, unstructured, andCartesian. For the iced configurations, these paradigms use hybrid body-fitted/source-term immersed-boundary, body-fitted, and ghost-cell immersed-boundary strategies, respectively.The unstructured and Cartesian mesh paradigms are particularly attractive for complex ice shapes as they avoid the manual mesh generation effort associated with the curvilinear approach. For the high-fidelity ice shape, good agreement with the experiment can be obtained with all three strategies; however, the curvilinear method is particularly sensitive to the source-term immersed-boundary timescale and span wise mesh resolution, and the Cartesian implementation is sensitive to the choice of numerical flux. For the smooth ice, larger discrepancies are observed across all methods. However, a mesh refinement study guided by flow visualizations leads to an improved comparison with the experiment that is particularly pronounced for the unstructured mesh paradigm.

TTT↗