Results for “insertion” — Page 75

NASA NTRS2014

Investigating Delamination Migration in Composite Tape Laminates

A modification to a recently developed test specimen designed to investigate migration of a delamination between neighboring ply interfaces in tape laminates is presented. The specimen is a cross-ply laminated beam consisting of 40 plies with a polytetrafluoroethylene insert spanning part way along its length. The insert is located between a lower 0-degree ply (specimen length direction) and a stack of four 90-degree plies (specimen width direction). The modification involved a stacking sequence that promotes stable delamination growth prior to migration, and included a relocation of the insert from the specimen midplane to the interface between plies 14 and 15. Specimens were clamped at both ends onto a rigid baseplate and loaded on their upper surface via a piano hinge assembly, resulting in a predominantly flexural loading condition. Tests were conducted with the load-application point positioned at various locations along a specimen's span. This position affected the sequence of damage events during a test.

Ratcliffe, James G.↗

NASA NTRS2015

Early Mission Maneuver Operations for the Deep Space Climate Observatory Sun-Earth L1 Libration Point Mission

The Deep Space Climate Observatory mission launched on February 11, 2015, and inserted onto a transfer trajectory toward a Lissajous orbit around the Sun-Earth L1 libration point. This paper presents an overview of the baseline transfer orbit and early mission maneuver operations leading up to the start of nominal science orbit operations. In particular, the analysis and performance of the spacecraft insertion, mid-course correction maneuvers, and the deep-space Lissajous orbit insertion maneuvers are discussed, com-paring the baseline orbit with actual mission results and highlighting mission and operations constraints..

OPERATIONS↗

NASA NTRS2018

SLS Block 1-B and Exploration Upper Stage Navigation System Design

The SLS Block 1B vehicle is planned to extend NASA's heavy lift capability beyond the initial SLS Block 1 vehicle. The most noticeable change for this vehicle from SLS Block 1 is the swapping of the upper stage from the Interim Cryogenic Propulsion stage (ICPS), a modified Delta IV upper stage, to the more capable Exploration Upper Stage (EUS). As the vehicle evolves to provide greater lift capability and execute more demanding missions so must the SLS Integrated Navigation System to support those missions. The SLS Block 1 vehicle carries two independent navigation systems. The responsibility of the two systems is delineated between ascent and upper stage flight. The Block 1 navigation system is responsible for the phase of flight between the launch pad and insertion into Low-Earth Orbit (LEO). The upper stage system assumes the mission from LEO to payload separation. For the Block 1B vehicle, the two functions are combined into a single system intended to navigate from ground to payload insertion. Both are responsible for self-disposal once payload delivery is achieved. The evolution of the navigation hardware and algorithms from an inertial-only navigation system for Block 1 ascent flight to a tightly coupled GPS-aided inertial navigation system for Block 1-B is described. The Block 1 GN&C system has been designed to meet a LEO insertion target with a specified accuracy. The Block 1-B vehicle navigation system is designed to support the Block 1 LEO target accuracy as well as trans-lunar or trans-planetary injection accuracy. This is measured in terms of payload impact and stage disposal requirements. Additionally, the Block 1-B vehicle is designed to support human exploration and thus is designed to minimize the probability of Loss of Crew (LOC) through high-quality inertial instruments and Fault Detection, Isolation, and Recovery (FDIR) logic. The preliminary Block 1B integrated navigation system design is presented along with the challenges associated with meeting the design objectives. This paper also addresses the design considerations associated with the use of Block 1 and Commercial Off-the-Shelf (COTS) avionics for Block 1-B/EUS as part of an integrated vehicle suite for orbital operations.

Oliver, T. Emerson↗

NASA NTRS2018

NASA Plum Brook Station In-Space Propulsion Facility Test Stand Characterization Hot Fire Test

A test facility modification to enable small scale altitude propulsion testing at the NASA Glenn Research Center's In-Space Propulsion (ISP) Facility was verified with a hot fire test campaign. As the facility's primary steam supply system undergoes refurbishment, the alternate facility configuration, known as the "vacuum accumulator" mode, would enable rocket engine testing up to 10,000 lbf thrust. The NASA Johnson Space Center developed the vehicle for the verification test campaign: the Integrated Cryogenic Propulsion Test Article (ICPTA). Constructed primarily from assets of the former Morpheus Project, the ICPTA provided an integrated liquid oxygen (LOX) / liquid methane (LCH4) propulsion system including a 2,800 lbf thrust main engine. The ISP Facility's vacuum accumulator configuration leveraged the large test volume of the facility and a diffuser insert to maintain altitude conditions. During hot fire, the ICPTA main engine "started" the diffuser insert constructed for the test campaign. As a result, the test chamber upstream of the diffuser insert remained at altitude conditions throughout the hot fire. Upon engine shut down, a backflow deflector mitigated blow back into the test chamber by restricting the mass flow and redirecting it away from the test article. The test campaign successfully characterized the performance of the vacuum accumulator configuration. In addition, it provided an opportunity to collect data for an integrated LOX / LCH4 propulsion system in an altitude and thermal vacuum environment.

Rocket Engine Testing↗

NASA NTRS2019

Design, Prototyping, and Testing of a Novel Flowpath with an Array of Six 3D Matrix Vitvo Bioreactors for the NASA Bioculture System

The NASA Bioculture System is an advanced cell culture closed-loop system containing highly automated flowpaths designed to conduct long term biology experiments on ISS with earth remote controllable medium flow, temperature, gas composition, medium exchange, cell sampling and fixation. This technology was already demonstrated with successful cardiomyocyte and osteocyte cultures experiments onboard the ISS and is now supporting NASA PI science. The Bioculture System, however, can only support 10 cassettes with disposable flowpaths, each containing a single hollow fiber bioreactor with a culture capacity of about 2ml. This constraint not only severely limits the number of investigators that can conduct experiments in space, but also subjects the experiments to limitations in the number of replicates and conditions that can be studied. To address these limitations, we sought a novel design solution to maximize the number of separate bioreactor cultures and volume that can be conducted simultaneously. To this end we designed, prototyped, and are now testing a six-Vitvo 3D Matrix 2ml bioreactor insert that replaces the conventional Bioculture System hollow fiber bioreactor. This design will allow the Bioculture System to support up to 60 different bioreactors and samples at once. Specifically, the novel gas-tight containment housing insert contains six COTS Rigenerand VITVO bioreactors stacked on each side of a heat sink powered by the existing heating element and pair of temperature sensors. Medium will be distributed into each bioreactor's cell-free chamber via its built-in Luer connector, then across the 3D matrix to the cell chamber, dissipating laminar flow and limiting fluid shear stresses that might mechanostimulate cell cultures. Gas (5% CO2 in air) will be supplied directly to the bioreactor gas-tight housing for exchange via the bioreactor flat-surface gas-permeable membranes, eliminating the need for the existing Bioculture System cassette oxygenator. If successfully implemented on ISS, this new multi-bioreactor insert for the Bioculture System has the potential to make real-time cell science experimentation in space more efficient and accessible to more investigators.

Ma, Kristin R.↗

NASA NTRSDate not supplied

Ballistic Lunar Transfers to Near Rectilinear Halo Orbit: Operational Considerations

This paper presents a study of ballistic lunar transfer (BLT) trajectories from Earth launch to insertion into a near rectilinear halo orbit (NRHO). BLTs have favorable properties for uncrewed launches to orbits in the vicinity of the Moon, such as dramatically reduced spacecraft ΔV requirements. Results are described from a detailed set of related mission design studies: BLTs with and without an outbound lunar flyby, insertion and rendezvous of a single spacecraft with a target in an NRHO, and insertion and rendezvous of multiple spacecraft with a target NRHO in quick succession. Monte Carlo analyses are presented of simulated rendezvous operations with realistic errors. These analyses are presented to inform future missions to NRHOs.

Nathan L Parrish↗

NASA NTRS2020

Aerocapture as an Enhancing Option for Ice Giants Missions

Investigation of Uranus and Neptune, via orbiter and atmospheric probes, is required to answer pressing science questions that have been raised in previous Decadal Surveys. As the Ice Giants are the farthest planets from Earth, traditional fully-propulsive orbit insertion missions would require a large amount of propellant, leaving less mass for the scientific payload; additionally, transit time to the planetary bodies near 13-15 years. Aerocapture uses aerodynamic forces generated by flight within a planetary atmosphere to decelerate and achieve orbit insertion. Although, aerocapture has not been used in the past, recent developments in thermal protection systems, guidance and control, and navigation capabilities enable the use of rigid, heritage entry vehicle configurations already flown at other planetary bodies for Ice Giants aerocapture. With the addition of these recent capabilities, aerocapture can robustly deliver spacecraft to Ice Giant orbits, while substantially increasing on-orbit payload mass (more than 40%) and reducing the transit time by 2-5 years (15-30%) relative to fully-propulsive orbit insertion.

Soumyo Dutta↗

NASA NTRSDate not supplied

Thermal Protection System to Enable Ice Giant Aerocapture Mission for Delivering Both an Orbiter and an In Situ Probe

The Ice Giants have been identified as high priority science destinations in the last Decadal Survey [1] and could benefit from aerocapture as the primary method for orbit insertion [2]. A mass-efficient aerocapture system will enable the delivery of an orbiter along with an atmospheric probe (for in situ measurements to anchor global data collected by the orbiter) and possibly a lander at Triton [3]. Aerocapture could be executed either using low L/D rigid aeroshell with lift modulation (LMA) [4] or using deployable aeroshell using drag modulation (DMA) [3]. Nearly two decades ago, a NASA-funded team performed Neptune-Triton aerocapture studies with a mid-L/D lifting configuration [5] for achieving orbit using LMA. This study showed aerocapture challenges. Due to very high peak entry conditions combined with very high heat-load, a suite of TPS materials was required and this suite was deemed problematic from a qualification perspective, due test facility limitations. In the past 20 years, progress made in GN&C for lift-guided entry missions such as MSL, Orion EFT1, Mars 2020 and the upcoming Artemis missions, and the expertise in blunt body aerodynamics at large scale (~ 5m) has led the EDL community to conclude that aerocapture is a “go do” engineering activity and most technologies are in hand to propose missions with aerocapture [6] [7]. Aerocapture using DMA, currently in development, is an option for Ice Giant Missions. While DMA is simpler in some sense, due to ballistic entry and no need for lift-guided maneuvering, it has challenges and it’s maturity is lower. LMA and DMA both require one or more ablative Thermal Protection System (TPS) materials for the rigid aeroshell element. The ablative TPS needs to be robust and mass efficient due to the high heat loads and size of the rigid aeroshell. Currently, there are capable ablative thermal protection materials, e.g., Heatshield for Extreme Entry Environments Technology (HEEET), 3-D woven Mid-Density Carbon- Phenolic (3MDCP), and PICA (Phenolic-Impregnated Carbon Ablator) that are mature, i.e., at TRL 6 or higher. NASA also invested in Conformal PICA that was matured to TRL 5. Our goal is to evaluate the applicability of high TRL TPS and consider other design options. We first establish bounding aerocapture trajectories for a wide range of arrival conditions and the associated aerothermal environment. Based on the environments, we then determine the predicted TPS mass for the aeroshell [4]. In this presentation, we will outline the process by which we establish bounding aerocapture trajectories for hyperbolic excess velocities ranging from 27 km/s to 35 km/s, which are shown to be a range of velocities that can reduce the trip time from ~14 years to 8 years. The above velocity range translates to ~12 km/s to ~24 km/s arrival velocities at the planetary entry interface [2]. The velocity reduction required to achieve orbit ranges between ~2.5 km/s to 9.5 km/s for both Neptune and Triton. Propulsive insertion alone, due to the amount of fuel required to achieve the required velocity reduction, limits the science returned [2]. We establish the bounding aerocapture trajectories for a low L/D (~ 0.4) configuration for three different ballistic coefficients. The ballistic coefficient range is determined from three different aeroshell diameters of 3m, 4m and 5m and with an entry system mass of 2200 kg. With the above range of design parameters, we then determine conservative/bounding estimates of aerothermal environments by using a combination of CFD simulations and stagnation point heating estimates [7]. This engineering approach allows us to first assess the TPS need vs. TPS capability and determine the applicability of existing TPS. Once an applicable suite of TPS is determined, the TPS thickness and mass are computed. We show that the TPS mass fraction can be as low as 5% to as high as 20%, depending on total trip time reduction and other design parameters for a range of TPS. This is a large range for TPS mass fraction. We show PICA and HEEET can indeed enable aerocapture missions, but the missions incur a mass penalty. TPS mass savings, can be further reduced with the use of conformal PICA. Advancing the development of Conformal PICA to make it robust across the entire aerothermal environment (peak heat-flux, pressure and shear) range will result in TPS mass fractions of < 10% for Ice Giant aerocapture missions such as the Neptune-Triton mission. Aerocapture allows for not only shortening the trip time but enables larger mass to be placed in orbit. Furthermore, probes deployed from orbit will benefit in reduced entry environments allowing for a lower risk TPS implementation as compared to mission designs where the probe is released prior to orbit insertion. One of the challenges for the Ice Giant community is to ensure mission designs that maximize science and allow flexibility in the placement of the entry probe. The traditional approach to release the probe ahead of the orbiter may not optimize returned science. In this presentation, we will make the case for mature TPS such as HEEET and PICA. While these materials can enable aerocapture missions, completing the development of conformal PICA and extending Conformal PICA to be more robust, will have significant impact to TPS mass efficiency and significantly enhance science return for future Gas- and Ice-Giant missions.

E Venkatapathy↗

NASA NTRSDate not supplied

Aerocapture as an Enabling Option for Ice Giants Missions

Investigation of Uranus and Neptune, via orbiter and atmospheric probes, is required to answer pressing science questions that have been raised in previous Decadal Surveys. As the Ice Giants are the farthest planets from Earth, traditional fully-propulsive orbit insertion missions have transit times to the planetary bodies nearing 13-15 years and require a large amount of propellant, leaving less mass for the scientific payload (dry mass percentages of around 30-40%). Aerocapture uses aerodynamic forces generated by flight within a planetary atmosphere to decelerate and achieve orbit insertion. Although, aerocapture has not been used in the past, recent developments in thermal protection systems, guidance and control, and interplanetary navigation capabilities enable the use of rigid, heritage entry vehicle configurations already flown at other planetary bodies for Ice Giants aerocapture. With the addition of these recent capabilities, aerocapture can robustly deliver spacecraft to Ice Giant orbits, while substantially increasing on-orbit payload mass (more than 40%) and reducing the transit time by 2-5 years (15-30%) relative to fully-propulsive orbit insertion.

Soumyo Dutta↗

NASA NTRSDate not supplied

Clearance Sensitivity Mitigation in Small Core Compressors

As future aircraft become lighter and more aerodynamically efficient, thrust requirements will decrease, reducing the core size of the engine. Furthermore, in the pursuit of improved fuel burn, engine overall pressure ratio and bypass ratio will increase, further driving down engine core size. These drivers together mean that the core size, or corrected mass flow rate at the compressor exit, for future single-aisle aircraft applications will shrink below 3.0 lbm/s. Traditionally, this small core compressor size is in the domain of axi-centrifugal designs, machines that are typically less efficient and limited to pressure ratios of ~25 due to stress and thermomechanical fatigue in the centrifugal impeller. In this light, NASA, Pratt & Whitney and the Raytheon Technologies Research Center embarked upon a program to develop technologies to enable an all-axial high-pressure compressor with a core size below 3.0 lbm/s and an overall pressure ratio greater than 50. One of the challenges with an all-axial high-pressure compressor at this core size is the small span at the rear of the compressor. As core size is scaled down, the rotor tip clearances do not scale with span, leading to significant efficiency penalties. This paper documents a numerical and experimental effort to mitigate this penalty through design optimization and technology insertion, enabling an estimated 5 to 10% fuel burn reduction relative to 2020 best-in-class. The experimental program consisted of two builds of a high-speed rig: a baseline build and a second build to insert technology to manage large rotor tip gap/span ratios. The results demonstrated a reduction in the sensitivity of the compressor to large clearance ratios, which would be likely at the end-of-life of a small core application. The test campaign demonstrated that, with the insertion of technology, small core compressors can maintain a similar efficiency to current best-in-class large core size compressors. In addition to advancing the state-of-the-art of technology, the program also advanced the modeling standards for multistage compressors with large clearance-to-span ratios. The validation of this approach is described in the paper.

Axial Compressors↗

NASA NTRSDate not supplied

The maize rough endosperm6 (rgh6) mutant encodes a predicted DEAD-box RNA helicase

Maize rough endosperm (rgh) mutants have defective seeds with a rough, etched, or pitted endosperm surface. Molecular genetic analysis of this mutant class has identified multiple RNA processing proteins critical to endosperm development. We isolated the rgh6 locus from the UniformMu transposon tagging population. Mutant kernels have reduced grain-fill with defective embryos that fail to germinate. Self-pollination of rgh6 heterozygotes produces mutant seeds at frequency consistent with a single recessive mutation. Molecular mapping localized rgh6 to a 60 kbp interval on chromosome 5. PCR analysis of gene models within the fine-map interval identified a Mutator (Mu) transposon insertion within a predicted DEAD-box RNA helicase gene. A second allele of rgh6 was identified from UniformMu population. Reciprocal crosses between rgh6-umu1 and rgh6-umu2 heterozygotes produces mutant seeds at a frequency consistent with a 3:1 ratio indicating these mutants are allelic. Both rgh6-umu1 and rgh6-umu2 have Mu element insertions at the same insertion site within the DEAD-box RNA helicase gene. However, the terminal inverted repeat sequences are polymorphic between the alleles showing the alleles are independent mutations. We conclude that mutation of the DEAD-box RNA helicase causes the rgh6 phenotype. Further characterization of the rgh6 mutant phenotype and biochemical investigation of the RGH6 protein is expected to give further insights on the roles of RNA processing in endosperm development.

maize↗

NASA NTRSDate not supplied

Clearance Sensitivity Mitigation in Small Core Compressors

As future aircraft become lighter and more aerodynamically efficient, thrust requirements will decrease, reducing the core size of the engine. Furthermore, in the pursuit of improved fuel burn, engine overall pressure ratio and bypass ratio will increase, further driving down engine core size. These drivers together mean that the core size, or corrected mass flow rate at the compressor exit, for future single-aisle aircraft applications will shrink below 3.0 lb/s. Traditionally, this small core compressor size is in the domain of axi-centrifugal designs, machines that are typically less efficient and limited to pressure ratios of ~25 due to stress and thermomechanical fatigue in the centrifugal impeller. In this light, NASA, Pratt & Whitney and the Raytheon Technologies Research Center embarked upon a program to develop technologies to enable an all-axial high-pressure compressor with a core size below 3.0 lb/s and an overall pressure ratio greater than 50. One of the challenges with an all-axial high-pressure compressor at this core size is the small span at the rear of the compressor. As core size is scaled down, the rotor tip clearances do not scale with span, leading to significant efficiency penalties. This paper documents a numerical and experimental effort to mitigate this penalty through design optimization and technology insertion, enabling an estimated 5 to 10% fuel burn reduction relative to 2020 best-in-class. The experimental program consisted of two builds of a high-speed rig: a baseline build and a second build to insert technology to manage large rotor tip gap/span ratios. The results demonstrated a reduction in the sensitivity of the compressor to large clearance ratios, which would be likely at the end-of-life of a small core application. The test campaign demonstrated that, with the insertion of technology, small core compressors can maintain a similar efficiency to current best-in-class large core size compressors. In addition to advancing the state-of-the-art of technology, the program also advanced the modeling standards for multistage compressors with large clearance-to-span ratios. The validation of this approach is described in the paper.

Axial Compressors↗

NASA NTRSDate not supplied

Enabling In-Situ Exploration of the Ice Giants Using Aerocapture

Investigation of the Ice Giants, especially Uranus, via orbiter and atmospheric probes, is required to answer pressing science questions that have been raised in the latest Decadal Survey. As the Ice Giants are the farthest planets from Earth, traditional fully-propulsive orbit insertion missions have transit times to the planetary bodies nearing 13- 15 years and require a large amount of propellant, leaving less mass for the scientific payload and a planetary probe (dry mass percentages of around 30- 40%). Aerocapture uses aerodynamic forces generated by flight within a planetary atmosphere to decelerate and achieve orbit insertion. Although, aerocapture has not been used in the past, recent developments in thermal protection systems (TPS), guidance and control, and interplanetary navigation capabilities enable the use of rigid, heritage entry vehicle configurations already flown at other planetary bodies for Ice Giants aerocapture. Aerocapture can robustly deliver spacecraft to Ice Giant orbits, while substantially increasing on-orbit payload mass (more than 40%) that can be used for a robust atmospheric entry probe. Additionally, the aerocapture maneuver would reduce the interplanetary transit time by 2-5 years (15-30%) relative to fully-propulsive orbit insertion.

S Dutta↗

NASA NTRSDate not supplied

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas Turbine↗

NASA NTRS2023

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas turbine↗

NASA NTRSDate not supplied

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas turbine↗

NASA NTRS2023

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas Turbine↗

NASA NTRSDate not supplied

Overview of the Lunar Transit Trajectory Performed by the Power and Propulsion Element of NASA’s Gateway

NASA has committed to returning to the moon, landing the first woman and the next man on its surface. To support a sustained lunar presence, NASA is designing an orbital platform to be assembled in an orbit near the moon called the Near Rectilinear Halo Orbit (NRHO). This platform is known as the Gateway and its purpose it to support missions primarily to the lunar south pole. As NASA continues to study ways to reduce the cost of lunar exploration, a simplification implemented in 2020combinedthe first two elements of the Gateway, the Power and Propulsion Element (PPE) and NASA’s Habitation and Logistics Outpost (HALO), onto a single commercial launch vehicle (CLV). When launched together, the PPE and HALO make up the first two elements of NASA’s Gateway and exceed the performance capacity of commercially available launch vehicles to deliver directly to the moon. The delivery of the Gateway is enabled by and takes advantage of the high efficiency of the PPEs high-power Solar Electric Propulsion (SEP) system to transfer a significant starting mass from an initial Earth orbit to final insertion into the NRHO. The PPE is a 50-kW class high power solar electric propulsion stage comprised of two different types of electric thruster strings. The SEP system is operated in two different modes, a high thrust and high Isp (specific impulse), to both maximize the final delivered mass and attempt to minimize the time spent in the Van Allen Belts early in the transit trajectory. Additionally, this SEP system brings the capability to the assembled Gateway for transfer between orbits in cislunar space. This paper captures the preliminary low thrust lunar transfer reference trajectory to be flown by the PPE it delivers itself and HALO via a spiral trajectory from launch vehicle insertion to insertion into the NRHO as well as a preliminary reference round trip transfer of the Gateway from the NRHO to a Distant Retrograde Orbit (DRO) using the PPE. Once in its final NRHO, the Gateway is being designed to enable long duration human and robotic exploration of the lunar south pole as a precursor to Mars. The Gateway’s low thrust lunar transit trajectory is envisioned to prove out the application of and flight of a high-power SEP system as a demonstration of technologies applicable to the enabling of future human space exploration.

human exploration↗