SEARCH · Search NASA
Results for “Loss function”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Interaction of solar and galactic cosmic-ray particles with the moon.
Calculation of the rates of formation of radionuclides as a function of depth in the moon for bombardments by galactic-cosmic-ray particles and by solar protons. The fluxes and spectra of galactic-cosmic-ray particles and of solar protons as a function of depth in the moon are first determined semiempirically. For galactic cosmic rays, the model emphasizes the production of secondary particles and the attenuation of particles by nuclear interactions. Solar proton calculations cover a range of observed spectral parameters, and only ionization energy losses need be considered. The excitation functions for the nuclear reactions used in these calculations are presented. The calculated production rates are given for a range of depths in the moon and are compared with experimental results and with earlier calculations. The model can also be applied to other effects of particle bombardment.
Chemical kinetics parameters and model validation for the gasification of PCEA nuclear graphite
A series of gasification experiments, using two right cylinder specimens (~ 12.7 x 25.4 mm and 25.4 x 25.4 mm) of PCEA nuclear graphite in ambient airflow, measured the total gasification flux at weight losses up to 41.5% and temperatures (893-1015 K) characteristics of those for in-pores gasification Mode (a) and in-pores diffusion-limited Mode (b). The chemical kinetics parameters for the gasification of PCEA graphite are determined using a multi-parameters optimization algorithm from the measurements of the total gasification rate and transient weight loss in experiments. These parameters are: (i) the pre-exponential rate coefficients and the Gaussian distributions and values of specific activation energies for adsorption of oxygen and desorption of CO gas; (ii) the specific activation energy and pre-exponential rate coefficient for the breakup of stable un-dissociated C(O2) oxygen radicals to form stable (CO) complexes; (iii) the specific activation energy and pre-exponential coefficient for desorption of CO2 gas and; (iv) the initial surface area of reactive free sites per unit mass. This area is consistently 13.5% higher than that for nuclear graphite grades of NBG-25 and IG-110 and decreases inversely proportional with the square root of the initial mass of the graphite specimens in the experiments. Experimental measurements successfully validate the chemical-reactions kinetics model that calculates continuous Arrhenius curves of the total gasification flux and the production rates of CO and CO2 gases. The model results at different total weight losses agree well with measurements and expand beyond the temperatures in the experiments to the diffusion-limited mode of gasification. Also calculated are the production rates of CO and CO2 gases and their relative contributions to the total gasification rate in the experiments as functions of temperature, for total weight losses of 5% and 10%.
SODR Memory Control Buffer Control ASIC
The Spacecraft Optical Disk Recorder (SODR) is a state of the art mass storage system for future NASA missions requiring high transmission rates and a large capacity storage system. This report covers the design and development of an SODR memory buffer control applications specific integrated circuit (ASIC). The memory buffer control ASIC has two primary functions: (1) buffering data to prevent loss of data during disk access times, (2) converting data formats from a high performance parallel interface format to a small computer systems interface format. Ten 144 p in, 50 MHz CMOS ASIC's were designed, fabricated and tested to implement the memory buffer control function.
Ab Initio modeling of Near-Edge EELS spectra for chemisorbed molecules
Abstract Electron energy loss spectroscopy (EELS) has recently been applied to probe chemisorbed molecules on metal nanostructures, but a fundamental understanding of the correlation between these spectra and the electronic structures of the adsorbates has been limited. We report here on the insights afforded by time-dependent density functional theory to decipher the energy loss near edge structure (ELNES) of EELS spectra associated with chemisorption. These first-principles calculations simulate the ELNES-EELS spectra for chemisorbed CO on various facets of Au and Pt. Computational predictions of key signatures such as the ‘red shift’ and reductions in the peak intensity of the 2 π * and 6 σ * peaks, as compared to free CO in the gas phase, are validated in comparison to experimentally collected EELS spectra. These signatures are revealed to arise from changes in the electronic structure in terms of unoccupied density of states associated with the chemisorption process. They are consistent with a Blyholder model that incorporates donation and back-donation of electrons. They are also characteristic of the chemisorption process, such as the choice of metal, site of adsorption and the coverage and distribution of adsorbates. Our simulations thus provide guidelines for the use of ELNES-EELS to characterize the atomic structure and adsorption property of nanostructured surfaces and facilitate the development of advanced nanomaterials for catalytic applications.
Electronic structure and energetics of a heterodimeric BChl g ′/Chl a ′ special pair generated by exposure of Heliomicrobium modesticaldum to dioxygen
Heliobacteria are anoxygenic phototrophs that have a Type I homodimeric reaction center containing bacteriochlorophyll g (BChl g). Previous experimental studies have shown that in the presence of light and dioxygen, BChl g is converted into 8 1 -OH-chlorophyll a F (hereafter Chl a F ), with an accompanying loss of light-driven charge separation. These studies suggest that the reaction center only loses the ability to transfer electrons once both BChl g′ molecules of the P 800 special pair have been converted to Chl a F ′. Here, the present work confirms that the partially converted BChl g′/Chl a F ′ special pair remains functional in samples exposed to dioxygen by demonstrating its presence using hyperfine couplings obtained from Q-band 1 H ENDOR, 2D 14 N HYSCORE and DFT methods. The DFT calculations of the BChl g′/BChl g′ homodimeric primary donor, which are based on the recently published X-ray crystal structure, predict that the unpaired electron spin is equally delocalized over both BChl g′ molecules and provide an excellent match to the experimental hyperfine couplings of the anaerobic samples. Exposure to dioxygen leads to substantial changes in the hyperfine interactions, indicative of greater localization of the unpaired electron spin. The measured hyperfine couplings are reproduced in the DFT calculations by replacing one of the BChl g′ molecules of the primary donor with a Chl a F ′ molecule. The calculations reveal that the spin density becomes localized on BChl g′ in the heterodimeric primary donor. Time-dependent DFT calculations demonstrate that conversion of either or both of the accessory BChl g molecules and/or one of the BChl g′ molecules of P800 to Chl a F ′ results in minor effects on the energy of the charge-separated states. In contrast, if both of the BChl g′ molecules of P 800 are converted a large increase in the energy of the charge-separated state occurs. This suggests that the reaction center remains functional when only one half of the dimer is converted, however, conversion of both halves of the P 800 dimer leads to loss of function
Demonstration of Thermoacoustic Power Sensor
The goal of this project is to develop and demonstrate a thermoacoustic power sensor (TAPS) for Sodium-cooled Fast Reactor (SFR), with potential application also envisioned to other nuclear technologies such as Lead-Cooled Fast Reactor (LFR), Molten Salt Reactor (MSR), in addition to Light Water Reactors (LWRs). The project was led by Westinghouse Electric Company, LLC (Westinghouse) and carried out in collaboration with Argonne National Laboratory (ANL) and the University of Pittsburgh. A TAPS is a passive (self-powered), non-invasive (wireless) sensor envisioned for measuring key parameters, such as local temperature and neutron flux, in a nuclear reactor core. The sensor generates pressure waves (i.e., sound waves) with a frequency and amplitude dependent upon nuclear operating conditions (coolant temperature or power changes). The acoustic waves are able to travel through the core and associated structures, and reach to the detector network placed outside of the reactor vessel. These detectors require a very small amount of power which, during loss of power events, can be provided for example by harvesting gamma radiation energy, thus resulting in a monitoring system that can function both during normal operation and during loss of power events.
Dielectric Response of Cross-Linked Polyethylene (XLPE) Cable Insulation Material to Radiation and Thermal Aging
This work seeks dielectric indicators of the aged state of cross-linked polyethylene (XLPE) that has been simultaneously irradiated and thermally aged. The XLPE samples studied here were of the same material formulation as XLPE insulation found in RSCC I46-0021 instrumentation cable, formed into tapes with dimensions approximately 20 × 0.7 × 100 mm 3 . Aging was conducted by suspending the samples from a rack within an oven and subsequently exposing oven and samples to gamma radiation. Samples were aged at 60, 90, and 115 °C, with gamma-radiation dose rates from 0 to 450 Gy/h with total received doses from 0 to 216 kGy. The dielectric spectra of these samples were measured over the frequency range 1 Hz to 1 MHz using custom electrodes and a Novocontrol dielectric spectrometer before dielectric breakdown strength was measured on the same samples. Dielectric loss tangent was observed to increase as a function of dose, dose rate and exposure time for XLPE samples exposed as described above. Dielectric loss tangent did not, however, show sensitivity to thermal aging for the range of temperatures studied. Dielectric breakdown strength initially increased as the material oxidized, then decreased for more extreme aging, due to chain scission. It is concluded that dielectric loss tangent is a promising indicator of XLPE aging due to gamma radiation exposure.
Java Architecture for Detect and Avoid Extensibility and Modeling
Unmanned aircraft will equip with a detect-and-avoid (DAA) system that enables them to comply with the requirement to "see and avoid" other aircraft, an important layer in the overall set of procedural, strategic and tactical separation methods designed to prevent mid-air collisions. This paper describes a capability called Java Architecture for Detect and Avoid Extensibility and Modeling (JADEM), developed to prototype and help evaluate various DAA technological requirements by providing a flexible and extensible software platform that models all major detect-and-avoid functions. Figure 1 illustrates JADEM's architecture. The surveillance module can be actual equipment on the unmanned aircraft or simulators that model the process by which sensors on-board detect other aircraft and provide track data to the traffic display. The track evaluation function evaluates each detected aircraft and decides whether to provide an alert to the pilot and its severity. Guidance is a combination of intruder track information, alerting, and avoidance/advisory algorithms behind the tools shown on the traffic display to aid the pilot in determining a maneuver to avoid a loss of well clear. All these functions are designed with a common interface and configurable implementation, which is critical in exploring DAA requirements. To date, JADEM has been utilized in three computer simulations of the National Airspace System, three pilot-in-the-loop experiments using a total of 37 professional UAS pilots, and two flight tests using NASA's Predator-B unmanned aircraft, named Ikhana. The data collected has directly informed the quantitative separation standard for "well clear", safety case, requirements development, and the operational environment for the DAA minimum operational performance standards. This work was performed by the Separation Assurance/Sense and Avoid Interoperability team under NASA's UAS Integration in the NAS project.
Electrical Properties and Power Considerations of a Piezoelectric Actuator
This paper assesses the electrical characteristics of piezoelectric wafers for use in aeronautical applications such as active noise control in aircraft. Determination of capacitive behavior and power consumption is necessary to optimize the system configuration and to design efficient driving electronics. Empirical relations are developed from experimental data to predict the capacitance and loss tangent of a PZT5A ceramic as nonlinear functions of both applied peak voltage and driving frequency. Power consumed by the PZT is the rate of energy required to excite the piezoelectric system along with power dissipated due to dielectric loss and mechanical and structural damping. Overall power consumption is thus quantified as a function of peak applied voltage and driving frequency. It was demonstrated that by incorporating the variation of capacitance and power loss with voltage and frequency, satisfactory estimates of power requirements can be obtained. These relations allow general guidelines in selection and application of piezoelectric actuators and driving electronics for active control applications.
Determination of navigation FDI thresholds using a Markov model
A method for determining time-varying Failure Detection and Identification (FDI) thresholds for single sample decision functions is described in the context of a triplex system of inertial platforms. A cost function consisting of the probability of vehicle loss due to FDI decision errors is minimized. A discrete Markov model is constructed from which this cost can be determined as a function of the decision thresholds employed to detect and identify the first and second failures. Optimal thresholds are determined through the use of parameter optimization techniques. The application of this approach to threshold determination is illustrated for the Space Shuttle's inertial measurement instruments.
Magnetic Field Angular Dependence of Magnetization Loss in ReBCO Superconducting Tapes
In the applications of high-temperature superconductors (HTS), the HTS tapes are usually exposed to the external magnetic field with different orientations. The critical current and AC loss are affected by both the field amplitude and field angles due to the anisotropy of HTS tapes. In this work, we first introduce the experimental system to measure the magnetization loss in HTS tapes based on the calibration-free method. Then, we present the magnetization loss results in 4.8-mm-wide AMSC wire, 4-mm-wide SuperPower wire, 4-mm-wide SuNam wire, and 10-mm-wide Fujikura wire in a perpendicular applied field at 77 K. The field amplitude is up to 100 mT, and the frequency varies from 44.2 to 87.1 Hz. We also present the magnetization loss in AMSC wire, SuperPower wire, SuNam wire, and Fujikura wire at different field angles. The field angle varies from 10 to 90 {sup ∘} in 10 {sup ∘} steps. The loss reduction with the decreasing of the field angle shows the anisotropic property of HTS tapes. We finally plot the measured magnetization loss of the samples as a function of the magnetic field amplitude normalized by the field angle to verify an empirical formula.
Microbial Potential for Ecosystem N Loss Is Increased by Experimental N Deposition
Fossil fuel combustion and fertilizer use has increased the amount of biologically available N entering terrestrial ecosystems. Nonetheless, our understanding of how anthropogenic N may alter the physiological mechanisms by which soil microorganisms cycle N in soil is still developing. Here, we applied shotgun metagenomics to a replicated long-term field experiment to determine how two decades of experimental N deposition, at a rate expected by mid-century, has affected the genetic potential of the soil microbial community to cycle N in soils. Experimental N deposition lead to a significant and persistent increase in functional assemblages mediating N cycle transformations associated with ecosystem N loss (i.e., denitrification and nitrification), whereas functional assemblages associated with N input and retention (i.e., N fixation and microbial N assimilation) were less positively affected. Furthermore, the abundance and composition of microbial taxa, as well as functional assemblages involved in housekeeping functions (i.e., DNA replication) were unaffected by experimental N deposition. Here taken together, our results suggest that functional genes and gene pathways associated with ecosystem N loss have been favored by experimental N deposition, which may represent a genetic mechanism fostering increased N loss as anthropogenic N deposition increases in the future.
Beyond mean-field dynamics in open Bose-Hubbard chains
We investigate the effects of phase noise and particle loss on the dynamics of a Bose-Einstein condensate in an optical lattice. Starting from the many-body master equation, we discuss the applicability of generalized mean-field approximations in the presence of dissipation as well as methods to simulate quantum effects beyond mean field by including higher-order correlation functions. It is shown that localized particle dissipation leads to surprising dynamics, as it can suppress decay and restorethe coherence of a Bose-Einstein condensate. These effects can be applied to engineer coherent structures such as stable discrete breathers and dark solitons.
Combining Pseudopotential and All Electron Density Functional Theory for the Efficient Calculation of Core Spectra Using a Multiresolution Approach
Broadly speaking, the calculation of core spectra such as electron energy loss spectra (EELS) at the level of density functional theory (DFT) usually relies on one of two approaches: conceptually more complex but computationally efficient projector augmented wave based approaches or more straightforward but computationally more intensive all electron (AE) based approaches. In this work we present an alternative method, which aims to find a middle ground between the two. Specifically, we have implemented an approach in the multiwavelet MADNESS molecular DFT code that permits a combination of atoms treated at the AE and pseudopotential (PSP) level. Atoms for which one wishes to calculate the core edges are thus treated at an AE level, while the remainder can be treated at the PSP level. This is made possible thanks to the multiresolution approach of MADNESS, which permits accurate and efficient calculations at both the AE and PSP level. Through examples of a small molecule and a carbon nanotube, this study demonstrates the potential applications of our approach.
Kinetic particle simulations in a global toroidal geometry
The gyrokinetic toroidal code has been upgraded for global simulations by coupling the core and scrape-off layer regions across the separatrix with field-aligned particle-grid interpolations. A fully kinetic particle pusher for high frequency waves (ion cyclotron frequency and beyond) and a guiding center pusher for low frequency waves have been implemented using cylindrical coordinates in a global toroidal geometry. The two integrators correctly capture the particle orbits and agree well with each other, conserving energy and canonical angular momentum. As a verification and application of this new capability, ion guiding center simulations have been carried out to study ion orbit losses at the edge of the DIII-D tokamak for single null magnetic separatrix discharges. The ion loss conditions are examined as a function of the pitch angle for cases without and with a radial electric field. We report the simulations show good agreement with past theoretical results and with the experimentally observed feature in which high energy ions flow out along the ion drift orbits and then hit the divertor plates. A measure of the ion direct orbit loss fraction shows that the loss fraction increases with the ion energy for DIII-D in the initial velocity space. Finally, as a further verification of the capability of the new code, self-consistent simulations of zonal flows in the core region of the DIII-D tokamak were carried out. All DIII-D simulations were performed in the absence of turbulence.
Understanding the Interactions of Seawater Ions with Amidoxime through X-Ray Crystallography
Insoluble polymer substrates functionalized with the amidoxime (R-C(NH 2 )=NOH) functional group have been demonstrated as a technically feasible platform for extracting uranium from seawater, a potential source of extremely abundant uranium for use as nuclear fuel. While it is possible to isolate macroscopic amounts of uranium from the ocean with a positive energy return on investment using these materials, both the economic and energetic costs are many times greater than those of terrestrial uranium mining. Currently, the major contribution to this cost is the production of the sorbent itself, so being able to recycle the sorbent even a small number of times will have a huge impact on lowering the cost of their use. However, amidoxime resins show capacity fading when stripped by strong acids, presently limiting their recyclability. Both alternative extractants and alternative elution chemistries are under development with promising results but are yet at too early a stage to make predictions about their ultimate success. Given the potentially huge impact of a successful recycling process on the viability of seawater extraction of uranium, there is a strong need to pursue additional routes to elution chemistry. During the course of this project, we studied the interactions of amidoxime-containing small molecules with the abundant metal ions in seawater, including Li, Na, K, Mg, Ca, Fe, Cu, and V, to understand the interactions of [UO 2 ] 2+ with amidoxime. By using small molecules with multiple adjacent functional groups, we crystallized the resulting metal complexes and used single crystal X-ray diffraction (SCXRD) as our primary tool for structural characterization. We also investigated the use of solutions of hydroxylammonium salts in weak acids as eluents for stripping and recycling amidoxime-based sorbents. The replacement of strong acids, which react with and destroy the amidoxime functional groups, with weak acids based on hydroxylammonium, a reagent that is actually used to make the amidoxime groups, is expected to avoid capacity loss on recycling and possibly even regenerate functionality that was lost due to exposure to the marine environment.
Role of Nrf2 antioxidant defense in mitigating cadmium-induced oxidative stress in the olfactory system of zebrafish
Exposure to trace metals can disrupt olfactory function in fish leading to a loss of behaviors critical to survival. Cadmium (Cd) is an olfactory toxicant that elicits cellular oxidative stress as a mechanism of toxicity while also inducing protective cellular antioxidant genes via activation of the nuclear factor (erythroid-derived 2)-like 2 (Nrf2) pathway. However, the molecular mechanisms of Cd-induced olfactory injury have not been characterized. In the present study, we investigated the role of the Nrf2-mediated antioxidant defense pathway in protecting against Cd-induced olfactory injury in zebrafish. A dose-dependent induction of Nrf2-regulated antioxidant genes associated with cellular responses to oxidative stress was observed in the olfactory system of adult zebrafish following 24 h Cd exposure. Zebrafish larvae exposed to Cd for 3 h showed increased glutathione S-transferase pi (gst pi), glutamate–cysteine ligase catalytic subunit (gclc), heme oxygenase 1 (hmox1) and peroxiredoxin 1 (prdx1) mRNA levels indicative of Nrf2 activation, and which were blocked by morpholino-mediated Nrf2 knockdown. The inhibition of antioxidant gene induction in Cd-exposed Nrf2 morphants was associated with disruption of olfactory driven behaviors, increased cell death and loss of olfactory sensory neurons (OSNs). Nrf2 morphants also exhibited a downregulation of OSN-specific genes after Cd exposure. Pre-incubation of embryos with sulforaphane (SFN) partially protected against Cd-induced olfactory tissue damage. Collectively, our results indicate that oxidative stress is an important mechanism of Cd-mediated injury in the zebrafish olfactory system. Moreover, the Nrf2 pathway plays a protective role against cellular oxidative damage and is important in maintaining zebrafish olfactory function. -- Highlights: ► Oxidative stress is an important mechanism of Cd-mediated olfactory injury. ► Cd induces antioxidant gene expression in the zebrafish olfactory system. ► The olfactory antioxidant response is blocked by Nrf2 knockdown. ► Disruption of olfactory neurobehaviors is associated with Nrf2 knockdown. ► Nrf2 morphants show increased cell death and olfactory sensory neuron loss.