Search NASA⌕ Search

SEARCH · Search NASA

Results for “PROCESSING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Physical, Chemical, and Mineralogical Characterizations of MSWI Ash Product and Recommendations for Downstream Processing

The primary objectives of this project are to (1) systematically characterize MSWI ash, and (2) based on characterization findings, design preliminary flowsheets for downstream processing. To achieve these objectives, a total of ten tasks were completed, including sample collection, physical separation tests, liberation tests, synthetic MSWI ash preparation, elemental composition analysis, sequential chemical extraction, mineralogical characterization, pozzolanic activity characterization, thermal stability characterization, processing flowsheet design, TEA and T2M, and project performance reporting. Many useful findings and conclusions were obtained from the exhaustive efforts of this project from several different aspects, including: a) Valuable Metals in MSWI Ash: MSWI ash contains a diverse array of valuable metals. Based on potential recoverable values, the most valuable metals present in MSWI ash include Fe, Ti, Mn, Cu, Zn, V, Co, Ni, Sr, Sn, Ag, Mo, and Sc. Some of these metals have been identified as critical minerals by DOE and DOI, suggesting that MSWI is a promising feedstock for critical mineral recovery. Noticeable graphical and seasonable variations in the valuable metal content of MSWI ash were observed. Nevertheless, it was challenging to discern any clear, definitive patterns for conclusions from those observations. Compared with bottom ash, fly ash contains more volatile metals, such as Zn and Sn, but less nonvolatile metals, such as Fe, Mn, Cu, Zn, Co, and Ni. Mineralogical analyses showed that MSWI ash contains a substantial amount of calcium minerals, such as portlandite, lime, gypsum, and calcite. In addition, it was found that different types of valuable metals often exist in the same particles. b) Physical Separation of MSWI Ash: Both dry sieving and wet sieving were performed on MSWI ash. A notable disparity in the size distribution of the same material was observed when using the two different sieving methods. The disparity is due to the agglomeration of small particles. For the valuable metals investigated, no significant enrichment in a specific size fraction was observed, suggesting that it is challenging to preconcentrate the valuable metals through size fractionation. Due to the presence of ferromagnetic materials, such as Fe, most of the materials reported to the magnetic products obtained by dry magnetic separation. However, the enrichment effect is minimal due to the existence of particle agglomerates. Density separation at a cut-off density of 2.7 SG or higher led to noticeable enrichment of selected valuable metals, particularly Ti. The unburned carbon present in MSWI ash was effectively removed by flotation using diesel as the collector. A novel reagent scheme, Na2S plus cationic collectors, that can efficiently beneficiate nonferrous metals plus Co was developed. c) Liberation Tests: The particle size of MSWI ash was effectively reduced by grinding, and as a result, the encapsulated valuable metal particles (if any) were liberated to a certain degree. However, particle size reductions did not noticeably enhance the beneficiation performance using the physical separation methods, primarily due to the inefficiency of these methods in processing fine particles and/or a possibility that insufficient liberation is not a limiting factor for achieving satisfactory physical separation performance. Valuable metals were classified into water leachable, ion-exchangeable, acid soluble, reducible, oxidable, and insoluble forms. It was found that the distributions in the different categories, i.e., the occurrence modes of the valuable metals, were not affected by the particle size. d) Leaching Characteristics of Metals from MSWI Ash: Most of the valuable metals were extracted from the fly ash samples when using 1 M HCl or HNO3 as the lixiviant. The leaching reaction is a very fast process, which can reach equilibrium within the first 5 min. The releasing of Co, Ni and Ag are sensitive to leaching temperature, a higher recovery value could be obtained when using relatively higher leaching temperatures. The leachability of the valuable metals present in MSWI bottom ash is relatively lower than that of fly ash. Leaching recoveries increased with elevations in the acid concentration. Relatively high leaching recoveries were obtained for REEs, Mn, Co, Ni, Cu, and Zn using 1 M HCl or HNO3 as the lixiviant. Elevations in the reaction temperature noticeably increased the leachability of the valuable metals, whereas the leachability was barely influenced by oxidizing and reducing agents. Similar to fly ash, leaching valuable metals from bottom ash is a rapid process, with most of the leaching reaction completed within the first 5 minutes. e) Combusted iPhones: The original structure of iPhones was remained after treating at 400 ºC and 600 ºC, while after being treated at 800℃, the screen bent, and the back cover of iPhone melted. Increasing the combustion temperature to 1000℃, the screen scattered, and most of the components turned into ashes. Combustion enhanced the leachability of REEs, while the leachability of the other valuable metals, except for Zn, was barely affected. Most of the REEs present in the original iPhones occurred as oxidizable forms. With elevations in the combustion temperature up to 600 ºC, the oxidizable REEs were transformed to acid soluble forms. However, further elevations in temperature resulted in decreases in the acid soluble fraction and corresponding increases in the reducible and oxidizable forms. Additionally, combustion temperature also significantly altered the occurrence modes of other metals present in the iPhones. f) Synthetic MSWI Ash: It was found that in the absence of hydrogen peroxide, all the elements except for Si were leached to certain degrees. It is noteworthy that approximately 80% of Zn was leached with 1.2 M HCl. When hydrogen peroxide was added to the reaction system, noticeable increases in the leaching recovery of Fe, Mn, Co, Ni, and Cu were observed. The leaching recovery of Al and Si was barely affected by adding hydrogen peroxide. These results suggested that the majority of Zn in the synthetic MSWI ash existed as metal oxide, a portion of Fe, Mn, Co, Ni, and Cu existed as metal oxide, and Al and Si are associated with glasses which are difficult to leach. Additionally, the remaining Fe, Mn, Co, Ni, and Cu in the metallic form were efficiently oxidized in the presence of hydrogen peroxide. g) Pozzolanic Activity and Thermal Stability of MSWI Ash: MSWI fly ash has higher pozzolanic activity compared to the bottom ash sample, which indicates that the fly ash sample consumed more portlandite because of its smaller particle size as reactivity fundamentally relates to reaction surface area. However, after the recovery of valuable elements, the pozzolanic activity of both the valuable elements fraction and the less valuable elements-rich products decreased significantly, which means that the valuable elements recovery lowers the Ca(OH)2 consumption, thus leading to the low activity of SCM. h) Flowsheet Design for Metal Recovery from MSWI Ash: Based on the results of the comprehensive physical separation and acid leaching tests, circuits that enable the beneficiation of the valuable metals were developed. In these circuits, the valuable metals are recovered into nonferrous, ferrous, and other valuable metal concentrates, which are processed separately in the acid leaching step. The subsequent separation and purification steps are simplified due to the physical beneficiation step. In addition, the overall recovery cost is reduced since physical beneficiation is much cheaper compared with chemical processing. Using different technologies, such as selective precipitation and solvent extraction, a comprehensive hydrometallurgical circuit was designed, and compounds of Cu, Zn, Mn, Co, and Ni with a purity close to or even higher than 95% were successfully generated.

36 MATERIALS SCIENCE↗

Coupling of Spark Plasma Sintering with Advanced Modeling to Enable Process Scale-Up: Presentation to DOE-NE [Slides]

The research goal of this project is to develop at Idaho National Laboratory (INL) a first-of-its-kind Multiphysics Object-Oriented Simulation Environment (MOOSE)-based, multiscale, multiphysics spark plasma sintering (SPS) modeling and simulation code application, termed “Freya.” Freya will simulate the thermo-mechanical-electrical aspects of the SPS fabrication process and will be paired with lower length scale sub-models, such as phase-field, to predict the resulting microstructure. SPS is an advanced manufacturing process that can be used to solve a variety of material manufacturing challenges; however, this process is an extremely challenging problem for modeling and simulation. The SPS process is inherently multiphysics and multi-scale, with the macroscale electro-thermo-mechanical behavior linked intricately to the microstructure evolution of the part being sintered. Accurate modeling and simulation tools, specifically geared towards the SPS process, are needed to predict the influence of the multiple variables involved in the manufacturing process. Modeling and simulation accuracy is achieved and demonstrated through comparison to multiple validation experiments. The validation efforts for Freya include both separate effects and complete multiphysics SPS process experiments. One of the key benefits this Laboratory Directed Research & Development (LDRD) project offers stems from the emphasis placed on experimental validation of the Freya models, both on the individual length scales and of the final coupled multiscale multiphysics simulations. Experimental validation of Freya’s multiscale coupling capability provides the technical credibility necessary for potential future industry and research partners to accept the simulation predictions.

36 MATERIALS SCIENCE↗

Improving Additive Manufactured Component Performance through Multi-Scale Microstructure Simulation and Process Optimization

The purpose of this project was to utilize computational tools to understand the relationships between processing, microstructure, and properties for additively manufactured (AM) aluminum alloys for automotive applications, and to provide an engineering solution for helping to optimize process conditions. The project leverages ORNL developments in computational modeling, including AM process modeling, phase-field based microstructure evolution predictions, and data analytics techniques for mapping process conditions to material outcomes. The project utilized an Al-Cu-Mn-Zr alloy as a model material for studying formation of defects and microstructural features in response to variations in process conditions. Based on both pre-existing experimental data and simulation results, statistical process maps were constructed to identify regions of process space with minimal defect formation and advantageous microstructures and properties. The software tools used for this purpose were successful disseminated to GM, who were able to successful compile the relevant HPC codes within their own computing ecosystem and perform initial calculations to reproduce ORNL results.

36 MATERIALS SCIENCE↗

Rapid Sensing to Facilitate Purification of Rare Earth Element-Containing Process Streams Produced Through Membrane-Assisted Solvent Extraction

The development of an economically competitive domestic supply of rare earth elements and yttrium (REY) is necessary for our nation’s economic growth and national security. The achievement of a secure domestic supply of REY requires not only the development of effective processes for recovery of REY from naturally occurring materials and/or recycled products, but also the development of downstream processes for the ultimate production of high-REY content solids. An impediment to the development of such processes is the scarcity of analytical methods that provide rapid determination of the process stream compositions. In this work, a membrane-based extraction process was used to selectively recover REYs from a dilute solution in the presence of much higher concentrations of Ca and Al. In tandem, the use of a portable spectrometer equipped with an immobilized zinc adeninate benzene tricarboxylate metal-organic framework sensing material makes possible the rapid detection of the presence of ppm concentrations of Tb and Eu in both weakly acidic and strongly acidic process streams within minutes. A solvent extraction processing time of 15-60 min maximized REY selectivity over gangue ions while achieving up to 80% REY and minimal gangue ion recovery. Taken together, these experiments highlight not only an innovative method for REY purification but also the importance of inexpensive, portable characterization methods for near real-time analysis of REY content.

Membrane-assisted solvent extraction↗

Data-Driven Optimization of the Processing Window for 316H Components Fabricated Using Laser Powder Bed Fusion

The Advanced Materials and Manufacturing Technologies Program is focused on accelerating the development and deployment of advanced materials and components fabricated via additive manufacturing with a specific focus on laser powder bed fusion (LPBF). As an initial case study, the program has selected 316H stainless steel (SS) as an initial material around which to develop a code case development strategy. This strategy involves two parallel approaches: (1) an equivalency approach whereby round-robin testing across multiple collaborating laboratories demonstrates repeatability in processing and direct comparisons with conventional wrought 316H material and (2) a revolutionary approach to code qualification combining in situ data collection and high-fidelity modeling to capture, predict, and bound the performance of LPBF 316HSS components. As part of this campaign, this work package has initiated an extensive process optimization campaign across three laboratories, each printing variations of LPBF 316HSS using three different LPBF units (Concept Laser, EOS, and Renishaw). In FY23, ORNL has focused on unique experimental designs spanning wide ranges in energy inputs and turning knobs such as scan speed, laser power, hatch spacing, layer thickness, spot size, scan rotation, and more. On the Concept Laser M2, 72 different combinations of processing variables were investigated with duplicate samples and different powder compositions. In total, 252 samples were printed with combined in situ sensing data. A parallel design of experiments was conducted on the Renishaw AM400 with an additional 390 printed specimens for analysis. All 642 miniature specimens, each with unique features included in each print to capture geometry-related heterogeneity, were subjected to high-throughput x-ray computed tomography (XCT) analysis to enable the downselection of specific processing parameters of interest. Then, using electrical discharge machining (EDM), miniature tensile specimens were extracted for mechanical testing and microscopy investigations. From the analysis performed in FY23, it was found that powder composition drastically affects the resulting microstructure and mechanical performance of 316SS. Specifically, changing from 316L to 316HSS powder results in a wide range of grain sizes with varying degrees of preferred grain orientation, which increases as a function of energy density. It was also found that due to stored heat in thin fin–type features, large microstructural differences can be seen within one part printed with one set of processing parameters. These variations in microstructure features, including grain size, the nanoscale dislocation structure, and grain texture, will all affect the irradiation performance and high-temperature mechanical performance of LPBF 316HSS parts. Two sets of concept laser processing parameters, spanning both refined and columnar grain structures, were scaled to print larger 316H builds for campaign testing (high-temperature creep and irradiation). In addition, at least two optimized processing parameter sets were identified for the Renishaw AM400 for round-robin testing in FY24 with Argonne National Laboratory. Future work includes printing samples using identical parameters identified by partner institutions, providing material for corrosion and high-temperature mechanical testing, and continuing evaluations of heterogeneity in larger printed parts.

36 MATERIALS SCIENCE↗

Data-Driven Optimization of the Processing Window for 316H Components Fabricated Using Laser Powder Bed Fusion

The Advanced Materials and Manufacturing Technologies Program is focused on accelerating the development and deployment of advanced materials and components fabricated via additive manufacturing with a specific focus on laser powder bed fusion (LPBF). As an initial case study, the program has selected 316H stainless steel (SS) as an initial material around which to develop a code case development strategy. This strategy involves two parallel approaches: (1) an equivalency approach whereby round-robin testing across multiple collaborating laboratories demonstrates repeatability in processing and direct comparisons with conventional wrought 316H material and (2) a revolutionary approach to code qualification combining in situ data collection and high-fidelity modeling to capture, predict, and bound the performance of LPBF 316HSS components. As part of this campaign, this work package has initiated an extensive process optimization campaign across three laboratories, each printing variations of LPBF 316HSS using three different LPBF units (Concept Laser, EOS, and Renishaw). In FY23, ORNL has focused on unique experimental designs spanning wide ranges in energy inputs and turning knobs such as scan speed, laser power, hatch spacing, layer thickness, spot size, scan rotation, and more. On the Concept Laser M2, 72 different combinations of processing variables were investigated with duplicate samples and different powder compositions. In total, 252 samples were printed with combined in situ sensing data. A parallel design of experiments was conducted on the Renishaw AM400 with an additional 390 printed specimens for analysis. All 642 miniature specimens, each with unique features included in each print to capture geometry-related heterogeneity, were subjected to high-throughput x-ray computed tomography (XCT) analysis to enable the downselection of specific processing parameters of interest. Then, using electrical discharge machining (EDM), miniature tensile specimens were extracted for mechanical testing and microscopy investigations. From the analysis performed in FY23, it was found that powder composition drastically affects the resulting microstructure and mechanical performance of 316SS. Specifically, changing from 316L to 316HSS powder results in a wide range of grain sizes with varying degrees of preferred grain orientation, which increases as a function of energy density. It was also found that due to stored heat in thin fin–type features, large microstructural differences can be seen within one part printed with one set of processing parameters. These variations in microstructure features, including grain size, the nanoscale dislocation structure, and grain texture, will all affect the irradiation performance and high-temperature mechanical performance of LPBF 316HSS parts. Two sets of concept laser processing parameters, spanning both refined and columnar grain structures, were scaled to print larger 316H builds for campaign testing (high-temperature creep and irradiation). In addition, at least two optimized processing parameter sets were identified for the Renishaw AM400 for round-robin testing in FY24 with Argonne National Laboratory. Future work includes printing samples using identical parameters identified by partner institutions, providing material for corrosion and high-temperature mechanical testing, and continuing evaluations of heterogeneity in larger printed parts.

36 MATERIALS SCIENCE↗

SLUDGE BATCH 6/TANK 40 SIMULANT CHEMICAL PROCESS CELL SIMULATIONS

Phase III simulant flowsheet testing was completed using the latest composition estimates for SB6/Tank 40 feed to DWPF. The goals of the testing were to determine reasonable operating conditions and assumptions for the startup of SB6 processing in the DWPF. Testing covered the region from 102-159% of the current DWPF stoichiometric acid equation. Nitrite ion concentration was reduced to 90 mg/kg in the SRAT product of the lowest acid run. The 159% acid run reached 60% of the DWPF Sludge Receipt and Adjustment Tank (SRAT) limit of 0.65 lb H2/hr, and then sporadically exceeded the DWPF Slurry Mix Evaporator (SME) limit of 0.223 lb H2/hr. Hydrogen generation rates peaked at 112% of the SME limit, but higher than targeted wt% total solids levels may have been partially responsible for rates seen. A stoichiometric factor of 120% met both objectives. A processing window for SB6 exists from 102% to something close to 159% based on the simulant results. An initial recommendation for SB6 processing is at 115-120% of the current DWPF stoichiometric acid equation. The addition of simulated Actinide Removal Process (ARP) and Modular Caustic Side Solvent Extraction Unit (MCU) streams to the SRAT cycle had no apparent impact on the preferred stoichiometric factor. Hydrogen generation occurred continuously after acid addition in three of the four tests. The three runs at 120%, 118.4% with ARP/MCU, and 159% stoichiometry were all still producing around 0.1 lb hydrogen/hr at DWPF scale after 36 hours of boiling in the SRAT. The 120% acid run reached 23% of the SRAT limit and 37% of the SME limit. Conversely, nitrous oxide generation was subdued compared to previous sludge batches, staying below 29 lb/hr in all four tests or about a fourth as much as in comparable SB4 testing. Two processing issues, identified during SB6 Phase II flowsheet testing and qualification simulant testing, were monitored during Phase III. Mercury material balance closure was impacted by acid stoichiometry, and significant mercury was not accounted for in the highest acid run. Coalescence of elemental mercury droplets in the mercury water wash tank (MWWT) appeared to degrade with increasing stoichiometry. Observations were made of mercury scale formation in the SRAT condenser and MWWT. A tacky mercury amalgam with Rh, Pd, and Cu, plus some Ru and Ca formed on the impeller at 159% acid. It contained a significant fraction of the available Pd, Cu, and Rh as well as about 25% of the total mercury charged. Free (elemental) mercury was found in all of the SME products. Ammonia scrubbers were used during the tests to capture off-gas ammonia for material balance purposes. Significant ammonium ion formation was again observed during the SRAT cycle, and ammonia gas entered the off-gas as the pH rose during boiling. Ammonium ion production was lower than in the SB6 Phase II and the qualification simulant testing. Similar ammonium ion formation was seen in the ARP/MCU simulation as in the 120% flowsheet run. A slightly higher pH caused most of the ammonium to vaporize and collect in the ammonia scrubber reflux solution. Two periods of foaminess were noted. Neither required additional antifoam to control the foam growth. A steady foam layer formed during reflux in the 120% acid run. It was about an inch thick, but was 2-3 times more volume of bubbles than is typically seen during reflux. A similar foam layer also was seen during caustic boiling of the simulant during the ARP addition. While frequently seen with the radioactive sludge, foaminess during caustic boiling with simulants has been relatively rare. Two further flowsheet tests were performed and will be documented separately. One test was to evaluate the impact of process conditions that match current DWPF operation (lower rates). The second test was to evaluate the impact of SRAT/SME processing on the rheology of a modified Phase III simulant that had been made five times more viscous using ultrasonication.

36 MATERIALS SCIENCE↗

A probabilistic inverse prediction method for predicting plutonium processing conditions

In the past decade, nuclear chemists and physicists have been conducting studies to investigate the signatures associated with the production of special nuclear material (SNM). In particular, these studies aim to determine how various processing parameters impact the physical, chemical, and morphological properties of the resulting special nuclear material. By better understanding how these properties relate to the processing parameters, scientists can better contribute to nuclear forensics investigations by quantifying their results and ultimately shortening the forensic timeline. This paper aims to statistically analyze and quantify the relationships that exist between the processing conditions used in these experiments and the various properties of the nuclear end-product by invoking inverse methods. In particular, these methods make use of Bayesian Adaptive Spline Surface models in conjunction with Bayesian model calibration techniques to probabilistically determine processing conditions as an inverse function of morphological characteristics. Not only does the model presented in this paper allow for providing point estimates of a sample of special nuclear material, but it also incorporates uncertainty into these predictions. This model proves sufficient for predicting processing conditions within a standard deviation of the observed processing conditions, on average, provides a solid foundation for future work in predicting processing conditions of particles of special nuclear material using only their observed morphological characteristics, and is generalizable to the field of chemometrics for applicability across different materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Novel Laser-Aided Machining and Polishing Process for Additive Manufacturing Materials with Multiple Endmill Emulating Scan Patterns

In additive manufacturing (AM), the surface roughness of the deposited parts remains significantly higher than the admissible range for most applications. Additionally, the surface topography of AM parts exhibits waviness profiles between tracks and layers. Therefore, post-processing is indispensable to improve surface quality. Laser-aided machining and polishing can be effective surface improvement processes that can be used due to their availability as the primary energy sources in many metal AM processes. While the initial roughness and waviness of the surface of most AM parts are very high, to achieve dimensional accuracy and minimize roughness, a high input energy density is required during machining and polishing processes although such high energy density may induce process defects and escalate the phenomenon of wavelength asperities. In this paper, we propose a systematic approach to eliminate waviness and reduce surface roughness with the combination of laser-aided machining, macro-polishing, and micro-polishing processes. While machining reduces the initial waviness, low energy density during polishing can minimize this further. The average roughness (Ra=1.11μm) achieved in this study with optimized process parameters for both machining and polishing demonstrates a greater than 97% reduction in roughness when compared to the as-built part.

42 ENGINEERING↗

Single Pass Laser Process for Super-Hydrophobic Flexible Surfaces with Micro/Nano Hierarchical Structures

Wetting has been studied in various fields: chemical industry, automobile manufacturing, food companies, and even life sciences. In these studies, super-hydrophobic surfaces have been achieved through complex steps and processes. To realize super-hydrophobicity, however, we demonstrated a simple and single pass laser process for the fabrication of micro/nano hierarchical structures on the flexible polytetrafluoroethylene (PTFE, Teflon) surface. The fabricated hierarchical structures helped increase the hydrophobicity by augmenting the surface roughness and promoting air-trapping. In addition, we employed a low-cost and high-throughput replication process producing numerous polydimethylsiloxane (PDMS) replicas from the laser-processed PTFE film. Thanks to the anti-adhesive characteristics of PTFE and the elasticity of PDMS, the structure perfectly transferred to the replica without any mechanical failure. Moreover, our designed mesh patterns offered the possibility of large area applications through varying the process parameters (pitch, beam spot size, laser fluence, and scan speed). Even though mesh patterns had relatively large pitch (190 μm), we were able to achieve high contact angle (>150°). Through pneumatically deformed structure, we clearly showed that the shape of the droplets on our laser-processed super-hydrophobic surface was spherical. Based on these outcomes, we can expect our single laser pulse exposure process can overcome many drawbacks and offer opportunities for advancing applications of the wetting phenomena.

36 MATERIALS SCIENCE↗

Uncertainties Induced by Processing Parameter Variation in Selective Laser Melting of Ti6Al4V Revealed by In-Situ X-ray Imaging

Selective laser melting (SLM) additive manufacturing (AM) exhibits uncertainties, where variations in build quality are present despite utilizing the same optimized processing parameters. In this work, we identify the sources of uncertainty in SLM process by in-situ characterization of SLM dynamics induced by small variations in processing parameters. We show that variations in the laser beam size, laser power, laser scan speed, and powder layer thickness result in significant variations in the depression zone, melt pool, and spatter behavior. On average, a small deviation of only ~5% from the optimized/reference laser processing parameter resulted in a ~10% or greater change in the depression zone and melt pool geometries. For spatter dynamics, small variation (10 μm, 11%) of the laser beam size could lead to over 40% change in the overall volume of the spatter generated. The responses of the SLM dynamics to small variations of processing parameters revealed in this work are useful for understanding the process uncertainties in the SLM process.

36 MATERIALS SCIENCE↗

Effects of Particle Size Distribution with Efficient Packing on Powder Flowability and Selective Laser Melting Process

The powder bed-based additive manufacturing (AM) process contains uncertainties in the powder spreading process and powder bed quality, leading to problems in repeatability and quality of the additively manufactured parts. This work focuses on identifying the uncertainty induced by particle size distribution (PSD) on powder flowability and the laser melting process, using Ti6Al4V as a model material. The flowability test results show that the effect of PSDs on flowability is not linear, rather the PSDs near dense packing ratios cause significant reductions in flowability (indicated by the increase in the avalanche angle and break energy of the powders measured by a revolution powder analyzer). The effects of PSDs on the selective laser melting (SLM) process are identified by using in-situ high-speed X-ray imaging to observe the melt pool dynamics during the melting process. The results show that the powder beds made of powders with dense packing ratios exhibit larger build height during laser melting. The effects of PSD with efficient packing on powder flowability and selective laser melting process revealed in this work are important for understanding process uncertainties induced by feedstock powders and for designing mitigation approaches.

36 MATERIALS SCIENCE↗

The Effects of Realistic Impact-processed Asteroid Topology on Atmospheric Airbursts

When small asteroids (∼10–200 m) enter Earth’s atmosphere they can break up before hitting the ground, releasing a considerable amount of energy in what is known as an atmospheric airburst. To date, numerous studies have examined how an asteroid’s strength, size, shape, and entry characteristics affect the breakup process; but few have assessed the effects of heterogenous internal topologies. We present a two-step high-fidelity simulation approach, which we use to model the atmospheric breakup of asteroids with realistic impact-processed internal topologies and their associated ground effects. In the first step, we model the asteroid as it is impacted to generate an “impact-processed” topology. We then map the resulting fractures (i.e., damage field) from that simulation to the initial state of an atmospheric breakup simulation. For both phases, we use the smoothed particle hydrodynamics code Spheral++. As a demonstrative example, we apply our new simulation pipeline to a Tunguska-scale impactor (50 m diameter, 20 km s −1 entry velocity, and 45° angle) in a case study comparing impact-processed and fully intact asteroids in both planar 2D and full 3D. For sufficiently strong asteroids, we find that impact processing generally causes the asteroid to break up at higher altitudes. We also observe that impact-processed asteroids break up into smaller fragments than objects with equivalent properties that have not been impact-processed.

Astronomy and AstroPhysics↗

Modelling feedbacks between human and natural processes in the land system

Abstract. The unprecedented use of Earth's resources by humans, in combination with increasing natural variability in natural processes over the past century, is affecting the evolution of the Earth system. To better understand natural processes and their potential future trajectories requires improved integration with and quantification of human processes. Similarly, to mitigate risk and facilitate socio-economic development requires a better understanding of how the natural system (e.g. climate variability and change, extreme weather events, and processes affecting soil fertility) affects human processes. Our understanding of these interactions and feedback between human and natural systems has been formalized through a variety of modelling approaches. However, a common conceptual framework or set of guidelines to model human–natural-system feedbacks is lacking. The presented research lays out a conceptual framework that includes representing model coupling configuration in combination with the frequency of interaction and coordination of communication between coupled models. Four different approaches used to couple representations of the human and natural system are presented in relation to this framework, which vary in the processes represented and in the scale of their application. From the development and experience associated with the four models of coupled human–natural systems, the following eight lessons were identified that if taken into account by future coupled human–natural-systems model developments may increase their success: (1) leverage the power of sensitivity analysis with models, (2) remember modelling is an iterative process, (3) create a common language, (4) make code open-access, (5) ensure consistency, (6) reconcile spatio-temporal mismatch, (7) construct homogeneous units, and (8) incorporating feedback increases non-linearity and variability. Following a discussion of feedbacks, a way forward to expedite model coupling and increase the longevity and interoperability of models is given, which suggests the use of a wrapper container software, a standardized applications programming interface (API), the incorporation of standard names, the mitigation of sunk costs by creating interfaces to multiple coupling frameworks, and the adoption of reproducible workflow environments to wire the pieces together.

58 GEOSCIENCES↗

Creating a Comprehensive, Efficient, and Sustainable Nuclear Regulatory Structure: A Process Report from the U.S. Department of Energy's Material Protection, Control and Accounting Program

With the congressionally mandated January 1, 2013 deadline for the U.S. Department of Energy’s (DOE) Nuclear Material Protection, Control and Accounting (MPC&A) program to complete its transition of MPC&A responsibility to the Russian Federation, National Nuclear Security Administration (NNSA) management directed its MPC&A program managers and team leaders to demonstrate that work in ongoing programs would lead to successful and timely achievement of these milestones. In the spirit of planning for successful project completion, the NNSA review of the Russian regulatory development process confirmed the critical importance of an effective regulatory system to a sustainable nuclear protection regime and called for an analysis of the existing Russian regulatory structure and the identification of a plan to ensure a complete MPC&A regulatory foundation. This paper describes the systematic process used by DOE’s MPC&A Regulatory Development Project (RDP) to develop an effective and sustainable MPC&A regulatory structure in the Russian Federation. This nuclear regulatory system will address all non-military Category I and II nuclear materials at State Corporation for Atomic Energy “Rosatom,” the Federal Service for Ecological, Technological, and Nuclear Oversight (Rostechnadzor), the Federal Agency for Marine and River Transport (FAMRT, within the Ministry of Transportation), and the Ministry of Industry and Trade (Minpromtorg). The approach to ensuring a complete and comprehensive nuclear regulatory structure includes five sequential steps. The approach was adopted from DOE’s project management guidelines and was adapted to the regulatory development task by the RDP. The five steps in the Regulatory Development Process are: 1) Define MPC&A Structural Elements; 2) Analyze the existing regulatory documents using the identified Structural Elements; 3) Validate the analysis with Russian colleagues and define the list of documents to be developed; 4) Prioritize and schedule the development of documents; 5) Identify and develop processes to measure effectiveness of regulations. Utilizing this process is resulting in an effective regulatory process that is understood and is being adopted by the four RF organizations. It is anticipated that the current regulatory development process will continue after U.S. support ends. Utilization of the systematic methodology will ensure regulatory development is based on required MPC&A structural elements and will support the continued maintenance and development of an effective regulatory base.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Optimization of carbon capture systems using surrogate models of simulated processes.

With increasing demand placed on power generation plants to reduce carbon dioxide (CO2) emissions, processes to separate and capture CO2 for eventual sequestration are highly sought after. Carbon capture processes impart a parasitic load on the power plants; it is estimated that this would increase the cost of electricity from existing pulverized coal plants anywhere from 71-85 percent [1]. The National Energy and Technology Lab (NETL) is working to lower this to below a 30 percent increase. To reach this goal, work is being done not only to accurately simulate these processes, but also to leverage those accurate and detailed simulations to design optimal carbon capture processes. The major challenges include the lack of accurate algebraic models of the processes, computationally costly simulations, and insufficiently robust simulations. The first challenge bars the use of provable derivative-based optimization algorithms. The latter two can either lead to difficult or impossible direct derivative-free optimization. To overcome these difficulties, we take a more indirect method to solving this problem by, first, generating an accurate set of algebraic surrogate models from the simulation then using derivative-based solvers to optimize the surrogate models. We developed a method that uses derivative-based and derivative-free optimization alongside machine learning and statistical techniques to generate the set of low-complexity surrogate models using data sampled from detailed simulations. The models are validated and improved through the use of derivative-free solvers to adaptively sample new simulation points. The resulting surrogate models can then be used in a superstructure-based process synthesis and solved using derivative-based methods to optimize carbon capture processes.

01 COAL, LIGNITE, AND PEAT↗

Formic Acid Free Flowsheet Development To Eliminate Catalytic Hydrogen Generation In The Defense Waste Processing

The Defense Waste Processing Facility (DWPF) processes legacy nuclear waste generated at the Savannah River Site (SRS) during production of plutonium and tritium demanded by the Cold War. The nuclear waste is first treated via a complex sequence of controlled chemical reactions and then vitrified into a borosilicate glass form and poured into stainless steel canisters. Converting the nuclear waste into borosilicate glass canisters is a safe, effective way to reduce the volume of the waste and stabilize the radionuclides. Testing was initiated to determine whether the elimination of formic acid from the DWPF's chemical processing flowsheet would eliminate catalytic hydrogen generation. Historically, hydrogen is generated in chemical processing of alkaline High Level Waste sludge in DWPF. In current processing, sludge is combined with nitric and formic acid to neutralize the waste, reduce mercury and manganese, destroy nitrite, and modify (thin) the slurry rheology. The noble metal catalyzed formic acid decomposition produces hydrogen and carbon dioxide. Elimination of formic acid by replacement with glycolic acid has the potential to eliminate the production of catalytic hydrogen. Flowsheet testing was performed to develop the nitric-glycolic acid flowsheet as an alternative to the nitric-formic flowsheet currently being processed at the DWPF. This new flowsheet has shown that mercury can be reduced and removed by steam stripping in DWPF with no catalytic hydrogen generation. All processing objectives were also met, including greatly reducing the Slurry Mix Evaporator (SME) product yield stress as compared to the baseline nitric/formic flowsheet. Ten DWPF tests were performed with nonradioactive simulants designed to cover a broad compositional range. No hydrogen was generated in testing without formic acid.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Direct access inter-process shared memory

A technique for directly sharing physical memory between processes executing on processor cores is described. The technique includes loading a plurality of processes into the physical memory for execution on a corresponding plurality of processor cores sharing the physical memory. An address space is mapped to each of the processes by populating a first entry in a top level virtual address table for each of the processes. The address space of each of the processes is cross-mapped into each of the processes by populating one or more subsequent entries of the top level virtual address table with the first entry in the top level virtual address table from other processes.

97 MATHEMATICS AND COMPUTING↗