Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase Transformations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

From material properties to multiscale modeling to improve lithium-ion energy storage safety

Energy storage using lithium-ion cells dominates consumer electronics and is rapidly becoming predominant in electric vehicles and grid-scale energy storage, but the high energy densities attained lead to the potential for release of this stored chemical energy. This article introduces some of the paths by which this energy might be unintentionally released, relating cell material properties to the physical processes associated with this potential release. The selected paths focus on the anode–electrolyte and cathode–electrolyte interactions that are of typical concern for current and near-future systems. Relevant material processes include bulk phase transformations, bulk diffusion, surface reactions, transport limitations across insulating passivation layers, and the potential for more complex material structures to enhance safety. We also discuss the development, parameterization, and application of predictive models for this energy release and give examples of the application of these models to gain further insight into the development of safer energy storage systems.

25 ENERGY STORAGE↗
DOE OSTI2021

Achieving strong and stable nanocrystalline Al alloys through compositional design

Abstract Al alloys often suffer from low mechanical strength and lack high-temperature microstructural and mechanical robustness. A series of binary and ternary nanocrystalline (NC) Al transition metal alloys with supersaturated solid solution and columnar nanograins have been recently developed by using magnetron sputtering, manifesting a new realm of mechanical properties and thermal stability. Distinct solutes cause evident differences in the phase transformations and efficiencies for grain refinement and crystalline-to-amorphous transition. Certain sputtered Al-TM alloys have shown room-temperature mechanical strengths greater than 2 GPa and outstanding thermal stability up to 400 °C. In addition, the NC Al alloys show mechanical anisotropy and tension–compression asymmetry, revealed by micromechanical tests. Through the process encapsulating various compositionally distinct systems, we attempt to illuminate the solute effects on grain refinement and properties and more importantly, tentatively unravel the design criteria for high-strength and yet thermally stable NC Al alloys. Graphic Abstract

36 MATERIALS SCIENCE↗
DOE OSTI2017

Mesoscale Connections Summer 2017

Our challenge derives from the fact that in metals or explosives grains, interfaces and defects control engineering performance in ways that are neither amenable to continuum codes (which fail to rigorously describe the heterogeneities derived from microstructure) nor computationally tractable to first principles atomistic calculations. This is a region called the mesoscale, which stands at the frontier of our desire to translate fundamental science insights into confidence in aging system performance over the range of extreme conditions relevant in a nuclear weapon. For dynamic problems, the phenomena of interest can require extremely good temporal resolutions. A shock wave traveling at 1000 m/s (or 1 mm/μs) passes through a grain with a diameter of 1 micron in a nanosecond (10-9 sec). Thus, to observe the mesoscale phenomena—such as dislocations or phase transformations—as the shock passes, temporal resolution better than picoseconds (10-12 sec) may be needed. As we anticipate the science challenges over the next decade, experimental insights on material performance at the micron spatial scale with picosecond temporal resolution—at the mesoscale— are a clear challenge. This is a challenge fit for Los Alamos in partnership with our sister labs and academia. Mesoscale Connections will draw attention to our progress as we tackle the mesoscale challenge. We hope you like it and encourage suggestions of content you are interested in.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Heat Treatment of Iron-Carbon Alloys in a Magnetic Field (Phase 2)

Thermomagnetic processing was shown to shift the phase transformation temperatures and therefore microstructural evolution in the high performance engine valve spring 9254 steel alloy by applying a high magnetic field during cooling. These effects would be anticipated to improve performance such as high cycle fatigue as demonstrated in prior projects. Thermomagnetic processing of gears and crank shafts was constrained by the size of the prototype equipment currently available at ORNL. However, the commercial procurement viability of production scale 9-Tesla, 16-inch diameter bore thermomagnetic processing equipment for truck idler gears up to ~11-inch diameter and potential crank shaft applications was shown, as multiple superconducting magnet manufacturing companies (in conjunction with an induction heat treating company, AjaxTOCCO Magnethermic) offered cryogen-free or cryocooler equipment designs to Cummins.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Multiscale Modeling of Deformation, Fracture and Failure of Fusion Materials and Structures Final Report

The main objective of the research performed at UCLA under grant number DE-FG02-03ER54708 was to develop a physical understanding of the underlying mechanisms that control high-temperature deformation and fracture of fusion structural materials. The key aspect is the synergistic interaction between thermo-mechanical damage phenomena (e.g. creep, fatigue, and fracture), and irradiation damage phenomena (helium and hydrogen bubbles, and irradiation-induced defects). Another thrust area of the research was on the development of constitutive equations for the mechanical behavior of irradiated structures in fusion components (mainly the First Wall and Plasma-Facing components), and in utilizing them in descriptions in large-scale Finite Element Modeling of fusion structures. A parallel experimental effort on thermo-mechanical and plasma-induced damage is designed to validate and confront the developed theoretical and computational predictions. The models have been experimentally validated through experimental tests in simulated plasma transients on specially-designed W samples. This grant started at UCLA on November 14, 2003 and has had successive continuations till November 14, 2017. Research performed under the grant was to develop a range of hierarchical models for the post-elastic deformation, fracture and failure of fusion structural materials. The developed multiscale modeling approach has been based on rigorous mathematical, physical, and computational methods at the forefront of computational materials science. At the fundamental and smallest length scale (nm-μm), we developed advanced rate theory and Monte Carlo approaches to model microstructure evolution, non-equilibrium phase transformations, and dislocation-defect interactions. Microscopic and mesoscopic models of radiation hardening, ductile-to-brittle-transition, post-elastic deformation, plastic instabilities, and fracture processes are based on Dislocation Dynamics (DD) and Grain Growth Dynamics (GGD). At the continuum level, we focused on modeling fracture and failure mechanisms for Virtual Integrated Testing (VISTA), and for understanding the limits of both materials-by-design versus structural component design through advancing the new approach of multiscale-multiphysics. The overall research has been strongly coupled with the U.S. national experimental program to ascertain and verify the range of investigated phenomena. In the following, we give a summary of research progress supported by this grant since its inception till November 14, 2017. Detailed research results are available in our publications, listed in the publications section of this report.

36 MATERIALS SCIENCE↗
DOE OSTI2018

CRADA Final Report: Weld Predictor App

Welding is an important manufacturing process used in a broad range of industries and market sectors, including automotive, aerospace, heavy manufacturing, medical, and defense. During welded fabrication, high localized heat input and subsequent rapid cooling result in the creation of residual stresses and distortion. These residual stresses can significantly affect the fatigue resistance, cracking behavior, and load-carrying capacity of welded structures during service. Further, additional fitting and tacking time is often required to fit distorted subassemblies together, resulting in non-value added cost. Using trial-and-error methods to determine which welding parameters, welding sequences, and fixture designs will most effectively reduce distortion is a time-consuming and expensive process. For complex structures with many welds, this approach can take several months. For this reason, efficient and accurate methods of mitigating distortion are in-demand across all industries where welding is used. Analytical and computational methods and commercial software tools have been developed to predict welding-induced residual stresses and distortion. Welding process parameters, fixtures, and tooling can be optimized to reduce the HAZ softening and minimize weld residual stress and distortion, improving performance and reducing design, fabrication and testing costs. However, weld modeling technology tools are currently accessible only to engineers and designers with a background in finite element analysis (FEA) who work with large manufacturers, research institutes, and universities with access to high-performance computing (HPC) resources. Small and medium enterprises (SMEs) in the US do not typically have the human and computational resources needed to adopt and utilize weld modeling technology. To allow an engineer with no background in FEA and SMEs to gain access to this important design tool, EWI and the Ohio Supercomputer Center (OSC) developed the online weld application software tool “WeldPredictor” ( https://eweldpredictor.ewi.org ). About 1400 users have tested this application. This project marked the beginning of development on the next version of WeldPredictor that addresses many outstanding features of the original, including 3D models, allow more material hardening laws, model material phase transformation, and uses open source finite element solvers to quickly solve problems (as opposed to expensive commercial tools).

42 ENGINEERING↗
DOE OSTI2018

Additive Manufacturing of a y0-Tetragonal Uranium-Niobium Alloy

The ability to process near-net shape structures is of particular interest in applications using rare or expensive materials. Laser powder bed fusion additive manufacturing can meet this challenge, yet also introduces significant processing and materials challenges toward achieving structural integrity. Broadly addressed aspects affecting powder bed fusion structures include surface roughness, residual stresses, and porosity. Here, we focus on materials-specific challenges—namely, the influence of multiple pass reheating during processing and post-processing homogenization on phase transformations and the role of impurities and oxides on grain morphology and mechanical behavior—with a view of adopting laser powder bed fusion processing for the shape memory alloy, uranium-6 wt.% niobium. Our observations to date on the factors influencing material behavior and post-processing requirements and recommendations for process improvement are discussed herein.

36 MATERIALS SCIENCE↗
DOE OSTI2018

X-Ray Diffraction Measurements on Laser-Compressed Polycrystalline Samples Using a Short-Pulse Laser Generated X-Ray Source

Existing models for most materials do not describe phase transformations and associated lattice dy- namics (kinetics) under extreme conditions of pressure and temperature. Dynamic x-ray diffraction (DXRD) allows material investigations in situ on an atomic scale due to the correlation between solid-state structures and their associated diffraction patterns. In this LDRD project we have devel- oped a nanosecond laser-compression and picosecond-to-nanosecond x-ray diffraction platform for dynamically-compressed material studies. A new target chamber in the Target Bay in building 983 was commissioned for the ns, kJ Z-Beamlet laser (ZBL) and the 0.1 ns, 250 J Z-Petawatt (ZPW) laser systems, which were used to create 8-16 keV plasma x-ray sources from thin metal foils. The 5 ns, 15 J Chaco laser system was converted to a high-energy laser shock driver to load material samples to GPa stresses. Since laser-to-x-ray energy conversion efficiency above 10 keV is low, we employed polycapillary x-ray lenses for a 100-fold fluence increase compared to a conventional pinhole aperture while simultaneously reducing the background significantly. Polycapillary lenses enabled diffraction measurements up to 16 keV with ZBL as well as diffraction experiments with ZPW. This x-ray diffraction platform supports experiments that are complementary to gas guns and the Z facility due to different strain rates. Ultimately, there is now a foundation to evaluate DXRD techniques and detectors in-house before transferring the technology to Z. This page intentionally left blank.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Spatially-dependent Hybridization of Potentials in LAMMPS

The purpose of the project was to facilitate joint Sandia/ExxonMobil collaborative research activities of mutual interest in the area of atomistic simulation of materials behavior using Sandia's LAMMPS molecular dynarnics software package. Work began in late 2013 and ended in early 2017. Initially, the main focus was on the development of a spatially-dependent hybridization capability for interatomic potentials in LAMMPS. Later, attention shifted to modeling and simulation of phase transformation kinetics in iron. Other research activities involved a variety of LAMMPS functionality, including interatomic potentials, Monte Carlo sampling, and energy minimization.

36 MATERIALS SCIENCE↗
DOE OSTI2018

HIGH-STRENGTH LIGHTWEIGHT ENGINES FOR HEAVY-DUTY DIESEL TRUCKS

This project with Cummins supports the development of next generation heavy duty diesel engines that can achieve a 50% or better Break Thermal Efficiency (BTE). The fuel efficiency roadmap for the 50% BTE engine considers six main areas for efficiency improvement in the baseline engine, several of which involve making more efficient use of thermal energy (heat) in the engine. Increased operating temperatures and improved thermal management are expected to enable significant increases in $power$ $density$, thus resulting in greater power output for the same sized engine or engine downsizing (or light weighting) for the same power output. However, it has become apparent that several key components will be exposed to temperatures beyond the capabilities of current engine and exhaust materials, requiring the availability of the next generation of high temperature materials to allow the engine to reach the targeted efficiencies, commercially viable durability, and emission targets. The objective of this project was to identify and/or develop key materials, and evaluate their critical properties to enable the design and development of a lightweight, higher efficiency engine, with enhanced temperature capability and reduced heat-loss to the atmosphere in order to facilitate waste heat recovery and improved efficiency. An increase in the temperature capability of exhaust manifold materials, and piston materials were identified as having a positive influence on the efficiency of the next generation diesel engines. Since the current materials (High SiMo cast irons used in exhaust manifolds, and 4140 steel in pistons) are already operating near their limits of their temperature and strength capabilities, it was determined that new materials with the right combination of properties are required for these components. Oxidation and constrained thermal fatigue tests were used to down-select CF8C plus (CF8CP), a cast austenitic stainless steel, for exhaust manifolds capable of operating at higher temperatures. A prototype exhaust manifold was fabricated using CF8CP and successfully tested in a marine engine. A functionally graded multiple-layer thermal barrier coating system was designed with four layers of mixed bondcoat alloy (NiCoCrAlYHfSi) and yttria stabilized zirconia (YSZ) and was shown to reduce the effective thermal conductivity of the coating-substrate (steel and Ti-6Al-4V) system. The graded alloy and YSZ mixture were intended to achieve better match of thermal expansion coefficient (CTE) and minimize thermal stresses. Such coatings can increase the temperature capability of pistons fabricated from steel and Ti-alloys. Effect of oil additives and friction conformal contact friction tests showed there was a 15-30% reduction in friction by the polymer-graphite composite coating compared to the uncoated steel piston. Standalone Mn-P coating had little beneficial impact. Changing the oil from CJ-4 to PC-11 had little impact on the friction behavior in boundary lubrication. Wear behavior was tested under a point contact configuration with a high contact pressure. The candidate CK-4 oil showed similar or slightly better lubricity compared to the CJ-4 oil while the candidate FA-4 oil decisively increased the piston skirt wear. Although both coatings prevented scuffing failure observed for the uncoated steel skirt in a base oil without an additive package, they surprisingly caused a higher piston wear rate when tested in any of the fully formulated engine oil. The detrimental impact was attributed to the Mn-P film, either as a standalone coating, or a coating interlayer. The porous and brittle Mn-P film was broken during the wear test and the released hard Mn-P grains are suspected to cause third-body abrasion to accelerate the wear process. This work also evaluated the feasibility of developing an improved high temperature, low mass, cost-neutral turbocharger compressor wheel for heavy-duty engine applications from TiAl using additive manufacturing, utilizing its unique ability to fabricate high strength, low weight structures. This work has shown that the phase transforming nature of the TiAl alloys enable obtaining equiaxed microstructures in the as-built state without the need for tedious beam parameter manipulations. The HIPed structures have good RT tensile properties that will enable them to be surface machined to the required tolerance that can 2 then be heat treated to obtain the desired microstructures. Additionally, the negligible residual stresses stemming from the high build chamber temperatures ensure the parts are formed without cracks (one of the major issues in traditional manufacturing of these intermetallics).

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2019

Investigating Grain Dynamics in Irradiated Materials with High-Energy X-rays (Final Report)

This report summarizes the research activities conducted at the Argonne National Laboratory (ANL) under the FY 2016 Consolidated Innovative Nuclear Research (CINR) Funding Opportunity Announcement (FOA) award CFA-16-10644: Investigating Grain Dynamics in Irradiated Materials with High-Energy X-rays. This project is a collaboration between the ANL and the Los Alamos National Laboratory (LANL). The research activities conducted at the LANL is summarized in the companion report, LA-UR-19-29312 titled “EVPSC Modeling of 316 Stainless Steel with and without Observed Phase Transformation.”

36 MATERIALS SCIENCE↗
DOE OSTI2019

Low-Cost, Efficient and Durable High Temperature Wireless Sensors by Direct Write Additive Manufacturing for Application in Fossil Energy Systems

In-situ monitoring of physical parameters in fossil energy (FE) systems is challenging because of their high operating temperatures and oxidizing environments. This research aims utilize Aerosol Jet (AJ) nanoparticle printing, an advanced additive manufacturing method, to fabricate high temperature sensors for FE applications. Sensor films were fabricated by the AJ printing method with an excellent control over film microstructure and properties, in addition to creating less waste. Printing of six different materials, namely, silver (Ag), nickel (Ni), nickel-chromium (NiCr) alloy, copper (Cu), copper-nickel (CuNi), and carbon nanotubes (CNTs) was carried out for their evaluation of as sensor films. The films were then characterized using impedance spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), x-ray diffraction (XRD), and x-ray photoelectron spectroscopy (XPS). Film microstructure was correlated with the sensor electrical and mechanical behavior at different temperatures (24-500 °C) and frequencies (0.02 - 300 kHz). This knowledge was then used to fabricate, test, and characterize strain and temperature sensors for high temperature applications. The strain sensors were shown to have a very low thermal strain up to 500 °C and a 57% higher gauge factor compared to the commercially available counterparts. This enhance performance was attributed to the inherent porosity in the sensor films that allowed the films to exhibit a metamaterial-like behavior when deformed. The AJ printed temperature sensors were shown to have the highest Seebeck coefficient amongst all the film-based temperature sensors. In addition, fundamental aspects of crystal structure and phase transformations in Ba(Fe0.7Ta0.3)O3-δ (BFTO), a high temperature sensor material, was investigated along with 3D printed antennas that can transmit sensor signals at high temperatures. Two PhD students, one from first generation college-going underrepresented minority community (URM), two postdoctoral fellows, and several masters and undergraduate students were supported by this award. This work opens up the possibility of realizing low-cost high-performance sensor devices using advanced manufacturing techniques for high temperature FE applications.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

Defects and Mechanical Behavior of Plutonium [Slides]

Defects are important because they heavily influence material properties (e.g. strength, ductility, elasticity, conductivity, phase transformation temperatures (melting point), corrosion resistance, etc.). At LANL defects in plutonium are being characterized using many different methods (e.g. EXAFS, XRD, microscopy, RUS, DSC, dilatometry, density, etc.) My goal is to introduce a complimentary method of understanding defects in δ-Pu using the mechanical microscope concept. Using well-developed theories of first principles strengthening mechanisms (i.e. how defects influence strength) and carefully designed experiments, mechanical testing can compliment other defect characterization tools.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Glass-Ceramic Material Modeling

Glass-ceramics are a unique class of materials in which the growth of a ceramic phase(s) may be induced in an inorganic glass resulting in a microstructurally heterogeneous material with both glass and ceramic phases. This specialized processing is often referred to as "ceramming''. A wide variety of such materials have been developed through the use of different initial glass compositions and thermomechanical processing routes and that have enabled applications in dentistry, consumer kitchenware, and telescopes mirrors. These materials may also exhibit large apparent coefficients of thermal expansion making them attractive for consideration in glass-ceramic seals. These large apparent coefficients of thermal expansion often arise from silica polymorphs, such as cristobalite, undergoing a solid-to-solid phase transformations producing additional non-linearity in the effective material response.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Limited-Ranged Two-Phase Iron Equation of State Model

This report describes the construction of a two-phase EOS for Fe that includes both (hcp) and liquid phases, and which is meant to be valid over the restricted range: V ϵ [4 : 7] °A 3 /atom, and T ϵ [1000 : 20000] K. It was recently used as the basis for a theoretical study of liquid → solid phase transformation kinetics in Fe which appeared in the Supplemental Material for a paper describing a series of NIF shock + ramp compression experiments aimed at constraining the high-P melt curve of Fe.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Development of Chromium and Sulfur Getter for Solid Oxide Fuel Cell (SOFC) System

Under the “real world” SOFC operating conditions, gaseous Cr and S species coexist in air stream. The combined Cr and S effect on the electrochemical poisoning of candidate LSM and LSCF electrodes has been investigated. Electrochemical and structural analysis revealed that the combined Cr and S interactions with the LSCF electrode remains significantly different from those of the individual Cr and S interactions. S reacts with the surface SrO accompanied by morphological changes whereas the hexavalent gaseous Cr species mainly deposit at the LSCF/GDC interface as is the case with Cr-only poisoning. For LSM electrode, the combined interactions of Cr and S remains similar to the sum of individual Cr and S effects as SO 2 reacts with Sr-rich regions of the bulk LSM, while Cr deposits at the electrochemically active sites. The use of getter, consisting of alkaline earth and transition metal oxides, has been proposed as a cost-effective approach to mitigate electrode poisoning. SrMnO 3 (SMO) is suggested as a robust getter material for the co-capture of airborne gaseous S and Cr species entering high-temperature electrochemical systems. The honeycomb getter forms, covered with SMO nanoparticles, were fabricated using dip coating. The SMO getter successfully maintained the electrochemical activity of LSM under the presence of gaseous Cr and S species, validating the efficacy of the getter. Post-test characterization revealed that the absorption of S and Cr contaminants led to the elongation of granular SMO particles, forming SrO nanorods and SrCrO 4 whiskers leaving Mn oxides underneath where inward-migrating Cr reside, indicating the high mutual affinity of Sr and Mn. The growth of reaction products during the long term exposure favors continued absorption of incoming S and Cr contaminants. The Mn 2 O 9 dimers, existing on the surface, are considered to help absorb S and Cr impurities, along with the Sr-terminated surface. The SMO getter also displays robust stability in humid environments at high temperatures without phase transformation or hydrolysis, fulfilling the requirement for operation in high-temperature electrochemical systems.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Probing the solidification of quasicrystals via joint experiment and simulation (Final Report)

Quasicrystals (QCs) possess long-range positional order but non-crystallographic orientational order. Their classically ‘forbidden’ symmetry has long attracted the interest of scientists worldwide. Despite their frequent observation in both metal alloys and soft matter structures in the 35 years since their discovery, little is known about how QCs evolve from a liquid, amorphous, or crystalline precursor. In this project, we sought to resolve the enigma of QC self-assembly through a combined experimental and computational program. The Shahani group employed in situ electron and synchrotron X ray imaging to peer into the growth dynamics of QCs in a liquid, covering a broad range of length scales and solidification pathways. Glotzer's team developed new simulation models incorporating phasonic defects — which are unique to quasicrystals — and used this model to investigate two grains growing together, closely mimicking the experimental conditions. While QCs remain exceptional structures, most compounds in the realm of intermetallics adopt non-trivial geometries. In fact, only around 6% of phases are comprised of the simplest sphere packings that researchers so readily associate with metals. State-of-the-art knowledge of phase transformations at the outset of this collaborative project did not encompass the remaining 94% of intermetallic compounds that possess complex and aperiodic structure types. Therefore, we expect that outcomes from this project will have immediate and profound impact on synthesis and processing science: our efforts will be used to not only explain the growth dynamics of QCs but also complex intermetallics more broadly.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Report summarizing demonstration of thermal conductivity measurement methods for coated zirconium cladding

Thermal diffusivity measurements on Zirconium-based cladding materials have historically been a challenge due to the difficulty to measure on specimens with curved geometries, including nuclear grade Zircaloy cladding materials. In this work, we first used Laser Flash Analysis methods to measure the thermal diffusivity of Zircaloy tubes, which show good agreement with Zircaloy plates in this work, as well as previously published data. The consistent results proved the applicability of the Laser Flash Analysis setup for investigating thermal diffusivity of Zircaloy tubes. We further investigate the hydrogen effect on thermal diffusivity of Zircaloy tubes. Hydrogen plays significant roles in temperature dependent thermal diffusivity trends of Zircaloy tube. For low hydrogen concentration, where hydride dissolved into single phase α-Zr at higher temperature, thermal diffusivity is relatively unchanged at low temperature at two phase regions (α-Zr and δ-hydride), and it increases as a function of temperature at single phase α-Zr region. For high hydrogen concentration, where phase transformation (α-Zr + δ-hydride → α-Zr + β-Zr) occurs at 567 °C, thermal diffusivity decreases as a function of temperature below 567 °C before the transformation (α-Zr and δ-hydride), while increase at higher temperature after the transformation (α-Zr and β-Zr).

36 MATERIALS SCIENCE↗