Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structural Effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Effect of torrefaction on biomass structure and hydrocarbon production from fast pyrolysis

Torrefaction has been shown to improve the chemical composition of bio-oils produced from fast pyrolysis by lowering its oxygen content and enhancing the aromatic yield. A Py-GC/MS study was employed to investigate the effect of torrefaction temperatures (225, 250 and 275 °C) and residence times (15, 30 and 45 min) on product distribution from non-catalytic and H + ZSM-5 catalyzed pyrolysis of pinewood. During torrefaction, structural transformations in biomass constitutive polymers: hemicellulose, cellulose and lignin took place, which were evaluated using component analysis, solid state CP/MAS 13 C NMR and XRD techniques. Torrefaction caused deacetylation and decomposition of hemicellulose, cleavage of aryl ether linkages and demethoxylation of lignin, degradation of cellulose and an overall increase in aromaticity of biomass, all of which affected the product yield from pyrolysis of torrefied biomass. For non-catalytic pyrolysis, selectivity of phenolic compounds increased with an increase in torrefaction severity while that of furan compounds decreased. In the case of catalytic pyrolysis, the sample torrefied at 225 °C-30 min and 250 °C-15 min resulted in a significant increase in aromatic hydrocarbon (HC) and also total carbon yield (approx. 1.6 times higher) as compared to catalytic pyrolysis of non-torrefied pine. Cleavage of aryl ether linkages and demethoxylation in lignin due to torrefaction caused increased yield of phenolic compounds, which in the presence of a catalyst were dehydrated to form aromatic HC.

09 BIOMASS FUELS↗

3 ns single-shot read-out in a quantum dot-based memory structure

Fast read-out of two to six charges per dot from the ground and first excited state in a quantum dot (QD)-based memory is demonstrated using a two-dimensional electron gas. Single-shot measurements on modulation-doped field-effect transistor structures with embedded InAs/GaAs QDs show read-out times as short as 3 ns. At low temperature (T = 4.2 K) this read-out time is still limited by the parasitics of the setup and the device structure. Faster read-out times and a larger read-out signal are expected for an improved setup and device structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetic, dielectric and magnetodielectric properties of PVDF-La{sub 0.7}Sr{sub 0.3}MnO{sub 3} polymer nanocomposite film

We have investigated the structure, magnetic and dielectric properties of PVDF-La{sub 0.7}Sr{sub 0.3}MnO{sub 3} polymer nanocomposite thick film fabricated by dip coating technique along with the magnetodielectric effect. The structure and dielectric properties show the enhanced β phase in the composite compared to the PVDF film. The coupling between the ferroelectric and magnetic phases in the composite is revealed in the form of dielectric anomaly at the ferromagnetic Curie temperature. We observed 1.9% magnetodielectric effect at 300 K with the possibility of enhanced effect near the transition temperature. In addition, the analysis of the electric modulus indicates that the composite exhibits interfacial related relaxation and it follows Arrhenius Law. Our study suggests that the ac conductivity of the PVDF-La{sub 0.7}Sr{sub 0.3}MnO{sub 3} composite could be explained by correlated barrier hopping mechanism.

36 MATERIALS SCIENCE↗

Structural and optical studies of CuO nanostructures

In the present study, copper oxide (CuO) nanostructures have been synthesized at 140 °C for different aging periods, 1, 24, 48 and 96 hrs by hydrothermal method to investigate their effects on structural and optical properties. The X-ray diffractometer (XRD) pattern indicates the pure phase formation of CuO and the particle size, calculated from XRD data, has been found to be increasing from 21 to 36 nm for the samples synthesized at different aging periods. Field emission scanning electron microscope (FESEM) analysis also shows that the average diameter and length of these rectangular nano flakes increases with increasing the aging periods. Moreover Raman spectrums also confirm the phase formation of CuO. The optical band gaps calculated through UV-visible spectroscopy are found to be decreasing from 2.92 to 2.69 eV with increase in aging periods, 1 to 96 hrs, respectively.

36 MATERIALS SCIENCE↗

Tuning the Mobility of Indacenodithiophene-Based Conjugated Polymers via Coplanar Backbone Engineering

Conjugated polymers based on indacenodithiophene-benzothiadiazole (IDT-BT) have attracted great interest due to their high charge carrier mobilities while being low crystallinity (i.e. near-amorphous.) They represent a promising design strategy to achieve both excellent stretchability and electrical performance. Here, we describe an approach on structural modifications of IDT-BT, namely by introducing non-covalent interactions and substituting building blocks to promote extended coplanar backbones. We systematically investigated the effects of structural modifications on backbone conformation, polymer aggregations, and charge carrier mobilities. Among the investigated polymers, the fluorinated derivative IDT-FBT demonstrated the highest charge carrier mobility of 5.19 cm 2 /Vs, along with low activation energy and Urbach energy indicating its low energy disorder level. The high mobility was attributed to the higher backbone planarity reinforced by S···F and H···F non-covalent interactions and improved interchain interactions through strong aggregation. In conclusion, our findings indicate that increasing backbone coplanarity may further improve mobility in low crystallinity conjugated polymers.

36 MATERIALS SCIENCE↗

Pressure effects on magnetic ground states in cobalt doped multiferroic Mn 1-x Co x WO 4

Using x-ray and high pressure neutron diffraction, we studied the pressure effect on structural and magnetic properties of multiferroic Mn 1-x Co x WO 4 single crystals (x = 0, 0.05, 0.135 and 0.17), and compared it with the effects of doping. Both Co doping and pressure stretch the Mn-Mn chain along the c direction. At high doping level (x = 0.135 and 0.17), pressure and Co doping drive the system in a very similar way and induce a spin-flop transition for the x = 0.135 compound. In contrast, magnetic ground states at lower doping level (x = 0 and 0.05) are robust against pressure but experience a pronounced change upon Co substitution. As Co introduces both chemical pressure and magnetic anisotropy into the frustrated magnetic system, our results suggest the magnetic anisotropy is the main driving force for the Co induced phase transitions at low doping level, and chemical pressure plays a more significant role at higher Co concentrations.

36 MATERIALS SCIENCE↗

Geometric Optimization of an Electrochemical Purification Cell to Prevent Corrosion in CSP Plants During Operation

When exposed to moisture or oxygen, molten chloride salts produce corrosive impurities which degrade containment alloys. As a result, this can significantly decrease the lifetime and increase costs of molten-salt-based systems. To overcome this barrier, we designed and modeled an electrochemical purification cell to remove the corrosive impurity MgOH+. Various reactor architectures, including constant stirred tank reactors (CSTRs) and plug flow reactors (PFRs) were investigated. Steady-state thermoelectric properties were evaluated, allowing assessment of the effects of structure and design parameters such as flow rate, cell length, and cross-sectional area of molten salt. The results suggest that our design could most effectively increase reliability and decrease costs of molten-chloride-salt-based systems by protecting them during continuous operation using an annular plug flow reactor.

chloride salts↗

Effect of Corona Block Length on the Structure and Chain Exchange Kinetics of Block Copolymer Micelles

The effect of corona block length on micelle structure and molecular chain exchange kinetics has been investigated for a series of dilute poly(styrene)-b-poly(ethylene-alt-propylene) (SEP) diblock copolymer micelles with constant PS core block length ($\langle$N core $\rangle$ ≈ 255) but different PEP corona block lengths (($\langle$N corona $\rangle$ = 256–2080), using a combination of dynamic light scattering (DLS), small-angle X-ray scattering (SAXS), and time-resolved small-angle neutron scattering (TR-SANS). Smaller core radii and aggregation numbers, but significantly thicker corona layers (proportional to N corona 0.7 ), were observed with increasing corona block length. Furthermore, 2 orders of magnitude more rapid chain exchange was observed in SEP micelles with the longest corona block compared to the shortest. This effect is attributed to the entropic gain arising from the relief of corona chain stretching upon chain expulsion. We further extend a previous theoretical model by explicitly including a corona term associated with the entropy change in the chain exchange process, which successfully explains the influence of the corona blocks on chain exchange. Our results are in excellent agreement with simulation results of Li and Dormidontova but are apparently contradictory with Halperin and Alexander’s theory for hairy micelles and with experimental observations in two other systems that the exchange kinetics slow down with increasing corona block length. These discrepancies reveal unanticipated complexity regarding the role of the corona block in chain exchange.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Band Gaps for Elastic Wave Propagation in a Periodic Composite Beam Structure Incorporating Microstructure and Surface Energy Effects

Here, a new model for determining band gaps for elastic wave propagation in a periodic composite beam structure is developed using a non-classical Bernoulli–Euler beam model that incorporates the microstructure, surface energy and rotational inertia effects. The Bloch theorem and transfer matrix method for periodic structures are employed in the formulation. The new model reduces to the classical elasticity-based model when both the microstructure and surface energy effects are not considered. The band gaps predicted by the new model depend on the microstructure and surface elasticity of each constituent material, the unit cell size, the rotational inertia, and the volume fraction. To quantitatively illustrate the effects of these factors, a parametric study is conducted. The numerical results reveal that the band gap predicted by the current non-classical model is always larger than that predicted by the classical model when the beam thickness is very small, but the difference is diminishing as the thickness becomes large. Also, it is found that the first frequency for producing the band gap and the band gap size decrease with the increase of the unit cell length according to both the current and classical models. In addition, it is observed that the effect of the rotational inertia is larger when the exciting frequency is higher and the unit cell length is smaller. Furthermore, it is seen that the volume fraction has a significant effect on the band gap size, and large band gaps can be obtained by tailoring the volume fraction and material parameters.

36 MATERIALS SCIENCE↗

Carbon quantum dots interfacial modified graphene/silicon Schottky barrier solar cell

The two-dimensional thin film, as an effective interface modification layer to improve the power conversion efficiency (PCE) of graphene/silicon (Gr/Si) heterojunction solar cells has attracted extensive attention recently. However, the complicated manufacturing process and specialized equipment requirements impede its broad application. Herein, carbon quantum dots (CQDs) fabricated under the mild reaction condition was first time used to modify Gr/Si devices interface structure. The effects of CQDs size distributions and coating thickness on J-V characteristics and the energy band structure of Gr/CQDs/Si solar cells were systematically analyzed. The findings indicate that the PCE of resulting Gr/CQDs/Si solar cells could reach 9.97% when the thickness and sizes of CQDs interlayer are ~26 nm and 4–7 nm, without any chemical doping, which is 6.8-times PCE than that of virgin Gr/Si solar cells. The CQDs interlayer serves as both an electron blocking layer and hole transport layer to reduce the carrier recombination, leading to a lower reverse saturation current as well as a larger VOC then improved the device performance. The enhanced PCE shows that the CQDs species have the potential applications in a cost-effective photovoltaic device.

14 SOLAR ENERGY↗

The growth of structure in interacting dark energy models

If dark energy interacts with dark matter, there is a change in the background evolution of the universe, since the dark matter density no longer evolves as a{sup −3}. In addition, the non-gravitational interaction affects the growth of structure. In principle, these changes allow us to detect and constrain an interaction in the dark sector. Here we investigate the growth factor and the weak lensing signal for a new class of interacting dark energy models. In these models, the interaction generalises the simple cases where one dark fluid decays into the other. In order to calculate the effect on structure formation, we perform a careful analysis of the perturbed interaction and its effect on peculiar velocities. Assuming a normalization to today's values of dark matter density and overdensity, the signal of the interaction is an enhancement (suppression) of both the growth factor and the lensing power, when the energy transfer in the background is from dark matter to dark energy (dark energy to dark matter)

79 ASTRONOMY AND ASTROPHYSICS↗

Grassland harvesting alters ant community trophic structure: An isotopic study in tallgrass prairies

Disturbances have long been recognized as important forces for structuring natural communities but their effects on trophic structure are not well understood, particularly in terrestrial systems. This is in part because quantifying trophic linkages is a challenge, especially for small organisms with cryptic feeding behaviors such as insects, and often relies on conducting labor-intensive feeding trials or extensive observations in the field. In this study, we used stable isotopes of carbon and nitrogen to examine how disturbance (annual biomass harvesting) in tallgrass prairies affected the trophic position, trophic range, and niche space of ants, a widespread grassland consumer. We hypothesized that biomass harvest would remove important food and nesting resources of insects thus affecting ant feeding relationships and trophic structure. We found shifts in the feeding relationships inferred by isotopic signatures with harvest. In particular, these shifts suggest that ants within harvest sites utilized resources at lower trophic levels (possibly plant-based resources or herbivores), expanded trophic breadth, and occupied different niche spaces. Shifts in resource use following harvest could be due to harvest-mediated changes in both the plant and arthropod communities that might affect the strength of competition or alter plant nitrogen availability. Because shifts in resource use alter the flow of nutrients across the food web, disturbance effects on ants could have ecosystem-level consequences through nutrient cycling.

54 ENVIRONMENTAL SCIENCES↗

Review of hadrons in medium

I review the present status in the theoretical and phenomenological understanding of hadron properties in strongly interacting matter. The topics covered are the EMC effect, nucleon structure functions in cold nuclear matter, spectral properties of light vector mesons in hot and cold nuclear matter, and in-medium properties of heavy flavored hadrons.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Structural Basis of CO 2 Adsorption in a Flexible Metal-Organic Framework Material

This paper reports on the structural basis of CO 2 adsorption in a representative model of flexible metal-organic framework (MOF) material, Ni(1,2-bis(4-pyridyl)ethylene)[Ni(CN) 4 ] (NiBpene or PICNIC-60). NiBpene exhibits a CO 2 sorption isotherm with characteristic hysteresis and features on the desorption branch that can be associated with discrete structural changes. Various gas adsorption effects on the structure are demonstrated for CO 2 with respect to N 2 , CH 4 and H 2 under static and flowing gas pressure conditions. For this complex material, a combination of crystal structure determination and density functional theory (DFT) is needed to make any real progress in explaining the observed structural transitions during adsorption/desorption. Possible enhancements of CO 2 gas adsorption under supercritical pressure conditions are considered, together with the implications for future exploitation. In situ operando small-angle neutron and X-ray scattering, neutron diffraction and X-ray diffraction under relevant gas pressure and flow conditions are discussed with respect to previous studies, including ex situ, a priori single-crystal X-ray diffraction structure determination. The results show how this flexible MOF material responds structurally during CO 2 adsorption; single or dual gas flow results for structural change remain similar to the static (Sieverts) adsorption case, and supercritical CO 2 adsorption results in enhanced gas uptake. Insights are drawn for this representative flexible MOF with implications for future flexible MOF sorbent design.

36 MATERIALS SCIENCE↗

Physical qubits from charged particles: Infrared divergences in quantum information

We consider soft-photon effects (ir structure of QED) on the construction of physical qubits. Soft photons appear when we build charged qubits from the asymptotic states of QED. This construction is necessary in order to include the effect of soft photons on entanglement measures. The nonexistence of free charged particles (due to the long range of QED interactions) leads us to question the sense of the very concept of free charged qubit. In this work, using the ''dressing'' formalism, we build physical charged qubits from dressed fields which have the correct asymptotic behavior, are gauge invariant, have propagators with a particle pole structure, and are free from infrared divergences. Finally, we discuss the impact of the soft corrections on the entanglement measures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Examining the Amine Functionalization in Dicarboxylates: Photoelectron Spectroscopy and Theoretical Studies of Aspartate and Glutamate

Aspartate (Asp 2- ) and Glutamate (Glu 2- ), two doubly charged conjugate bases of the corresponding amino acids were investigated using low temperature negative ion photoelectron spectroscopy (NIPES) and ab-initio calculations. The effect of amine functionalization was studied by a direct comparison to the parent dicarboxylate species ( - CO 2 –(CH 2 ) n –CO 2 -, DC n 2- ) -- succinate (DC 2 2- ) and propionate (DC 3 2- ). Experimentally the addition of amine group for n = 2 case (DC 2 2- , Asp 2- ) significantly improves the stability of the resultant Asp 2- dianionic species, albeit that NIPES shows only a small increase in adiabatic electron detachment energy (ADE) (+0.05eV). In contrast, for n = 3 (DC 3 2- , Glu 2- ), much larger ADE increase is observed (+0.15eV). Similar results are obtained through ab-initio calculations. The latter indicates that increased stability of Asp 2- can be attributed to the lowering of the energy of singlet dianion state due to hydrogen bonding effects. The effect of the amino group on the doublet monoanion state is more complicated, and results in the weakening of the binding of the adjacent carboxylate group due to electronic structure resonance effects. This conclusion is confirmed by the analysis of NIPES results that show enhanced production of near zero kinetic energy electrons observed experimentally for amine-functionalized species.

Environmental Molecular Sciences Laboratory↗

Structure alterations in microporous (Mg,Fe){sub 2}Al{sub 4}Si{sub 5}O{sub 18} crystals induced by energetic heavy-ion irradiation

The microporous framework structure of (Mg{sub 1-x}Fe{sub x}){sub 2}Al{sub 4}Si{sub 5}O{sub 18} (=cordierite) has been subject to a comparative study on the effect of structural alterations originating from exposure to high-energy heavy ions. Oriented samples (with x=0.061, 0.122, and 0.170) were irradiated with swift {sup 124}Xe, {sup 197}Au and {sup 96}Ru ions with 11.1 MeV per nucleon energy and fluences of 1x10{sup 12} and 1x10{sup 13} ions/cm{sup 2}. Irradiated and non-irradiated samples were investigated by means of X-ray diffraction, Moessbauer spectroscopy and optical absorption spectroscopy. Structural investigations reveal an essentially unchanged Al,Si ordering, which appears to be unaffected by irradiation. The most remarkable macroscopic change is the ion-beam induced colouration, which could be assigned to electronic charge transfer transitions involving the Fe cations. Moessbauer spectra indicate an increased amount of {sup [4]}Fe{sup 3+} for the irradiated sample. The most noticeable structural alteration concerns irradiation-induced dehydration of extra-framework H{sub 2}O, which is accompanied by a reduction in the molar volume by {approx}0.2 vol%. - Graphical abstract: Cordierite single-crystal specimen showing the color change from pale blue (unirradiated) to a yellowish brown layer (irradiated) after exposure to relativistic {sup 124}Xe ions at a fluence of 1x10{sup 12} ions per cm{sup 2}.

36 MATERIALS SCIENCE↗

Analysis of the Effect of Different Initial States and Structural Defects on the Characteristics of the Nonequilibrium Critical Behavior of the 3D Ising Model

The effect of different initial values m{sub 0} of magnetization and structural defects on the nonequilibrium critical behavior of the 3D Ising model have been analyzed numerically using the Monte Carlo method. Analysis of the two-time dependences of the autocorrelation function and dynamic susceptibility has revealed a substantial influence of the initial states on the aging effects that are characterized by anomalous retardation of relaxation and correlation in the system upon an increase in the waiting time. We have studied the violations of the fluctuation–dissipation theorem and calculated the limiting fluctuation–dissipation ratio. It is shown that in the nonequilibrium critical behavior of the 3D Ising model, two universality subclasses corresponding to the evolution of the system from the high-temperature (with m{sub 0} = 0) and low-temperature (with m{sub 0} = 1) initial states with the values of the limiting fluctuation–dissipation ratio typical of these states can be singled out.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗