Search NASA⌕ Search

SEARCH · Search NASA

Results for “WIND MODELING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Verification of a Numerical Model of the Offshore Wind Turbine From the Alpha Ventus Wind Farm Within OC5 Phase III

The main objective of the Offshore Code Comparison Collaboration Continuation, with Correlation (OC5) project, is validation of aero-hydro-servo-elastic simulation tools for offshore wind turbines (OWTs) through comparison of simulated results to the response data of physical systems. Phase III of the OC5 project analyzes the Senvion 5M wind turbine supported by the OWEC Quattropod from the alpha ventus offshore wind farm. This paper shows results of the verification of the OWT models (code-to-code comparison). A subsequent publication will focus on their validation (comparison of simulated results to measured physical system response data). Based on the available data, the participants of Phase III set up numerical models of the OWT in their simulation tools. It was necessary to verify and to tune these models. The verification and tuning were performed against an OWT model available at the University of Stuttgart - Stuttgart Wind Energy (SWE) and documentation provided by Senvion and OWEC Tower. A very good match was achieved between the results from the reference SWE model and models set up by OC5 Phase III participants.

17 WIND ENERGY↗

Validating a time-dependent turbulence-driven model of the solar wind

Although the mechanisms responsible for heating the Sun's corona and accelerating the solar wind are still being actively investigated, it is largely accepted that photospheric motions provide the energy source and that the magnetic field must play a key role in the process. Verdini et al. presented a model for heating and accelerating the solar wind based on the turbulent dissipation of Alfvén waves. We first use a time-dependent model of the solar wind to reproduce one of Verdini et al.'s solutions; then, we extend its application to the case where the energy equation includes thermal conduction and radiation losses, and the upper chromosphere is part of the computational domain. Using this model, we explore the parameter space and describe the characteristics of a fast solar wind solution. We discuss how this formulation may be applied to a three-dimensional MHD model of the corona and solar wind.

79 ASTRONOMY AND ASTROPHYSICS↗

Blade Testing Equipment Development and Commercialization: Cooperative Research and Development (Final Report)

Blade testing is required to meet wind turbine design standards, reduce machine cost, and reduce the technical and financial risk of deploying mass-produced wind turbine models. NREL's National Wind Technology Center (NWTC) in Colorado is the only blade test facility in the U.S. capable of performing full-scale static and fatigue testing of multi-megawatt-scale wind turbine blades. Rapid growth in wind turbine size over the past two decades has outstripped the size capacity of the NWTC blade test facility leaving the U.S. wind industry without a suitable means of testing blades for large land-based and offshore turbines. This CRADA will develop and commercialize testing technologies and test equipment, including scaling up, value engineering, and testing of equipment to be used at blade testing facilities in the U.S. and around the world.

17 WIND ENERGY↗

CCBlade Documentation: Release 0.1.0

CCBlade predicts aerodynamic loading of wind turbine blades using blade element momentum (BEM) theory. CC stands for continuity and convergence. CCBlade was developed primarily for use in gradient-based optimization applications where C1 and robust convergence are essential.

17 WIND ENERGY↗

AirfoilPrep.py Documentation: Release 0.1.0

AirfoilPrep.py provides functionality to preprocess aerodynamic airfoil data. Essentially, the module is an object oriented version of the AirfoilPrep spreadsheet with additional functionality and is written in the Python language. It allows the user to read in two-dimensional aerodynamic airfoil data, apply three-dimensional rotation corrections for wind turbine applications, and extend the datato very large angles of attack. This document discusses installation, usage, and documentation of the module.

17 WIND ENERGY↗

pBEAM Documentation: Release 0.1.0

The Polynomial Beam Element Analysis Module (pBEAM) is a finite element code for beam-like structures. It was originally written to analyze tower/monopiles and rotor blades of wind turbines but can be used for any beam-like structure. This document discusses installation, usage, and documentation of the module.

17 WIND ENERGY↗

Alaska Wind Energy Project

The Alaska Wind Energy Research Project will support studies that provide new learning on wind-diesel modeling techniques and operating wind turbine systems in arctic environments

17 WIND ENERGY↗

Maximum principle solutions for time-optimal half-loop maneuvers of a high alpha fighter aircraft

An investigation was conducted of maximum principle solutions for an initial 0.6 Mach number and 15,000-ft altitude. The authors generate these solutions for a family of prescribed final times tf, starting with tf = 0.5 s. Using a nonlinear wind-tunnel model they construct maximum principle solutions. Above tf = 1.2 s some small nonlinear variations in the aerodynamic pitching moment coefficient presented difficulty with respect to numerical convergence. This was circumvented by fitting analytical models to the aerodynamic coefficients of the wind-tunnel model at Mach 0.4. Maximum principle solutions of the analytical model are shown to compare well with those obtained for tf of less than 1.2 s. Using the analytical model the authors extended the prescribed final time to a value of 13.65 s at which time the aircraft completes the half-loop maneuver. This is 0.53 s longer than that obtained using the singular perturbation feedback control law.

Stalford, Harold↗

Ionospheric plasma outflow in response to transverse ion heating: Self-consistent macroscopic treatment

We examined the various likely processes for creating the cavities and found that the mirror force acting on the transversely heated ions is the most likely mechanism. The pondermotive force causing the wave collapse was found to be a much weaker force than the mirror force on the transversely heated ions observed inside the cavities along with the lower hybrid waves. Using a hydrodynamic model for the polar wind we modeled the cavity formation and found that for the heating rate obtained from the observed waves, the mirror force does create cavities with depletions as observed. Some initial results from this study were published in a recent Geophysical Research Letters and were reported in the Fall AGU meeting in San Francisco. We have continued this investigation using a large-scale semikinetic model.

Singh, N.↗

Aerodynamic Properties Analysis of Rapid Prototyped Models Versus Conventional Machined Models

Initial studies of the aerodynamic characteristics of proposed launch vehicles can be made more accurately if lower cost, high fidelity aerodynamic models are available for wind tunnel testing early in the design phase. This paper discusses the results of a study undertaken at NASA's Marshall Space Flight Center to determine if four rapid prototyping methods using a variety of materials are suitable for the design and manufacturing of high speed wind tunnel models in direct testing applications. It also gives an analysis of whether these materials and processes are of sufficient strength and fidelity to withstand the testing environment. In addition to test data, costs and turn-around times for the various models are given. Based on the results of this study, it can be concluded that rapid prototyping models show promise in limited direct application for preliminary aerodynamic development studies at subsonic, transonic, and supersonic speeds.

Springer, A.↗

COTS MEMS Flow-Measurement Probes

As an alternative to conventional tubing instrumentation for measuring airflow, designers and technicians at Glenn Research Center have been fabricating packaging components and assembling a set of unique probes that contain commercial off-the-shelf (COTS) microelectromechanical systems (MEMS) sensor chips. MEMS sensor chips offer some compelling advantages over standard macroscopic measurement devices. MEMS sensor technology has matured through mass production and use in the automotive and aircraft industries. At present, MEMS are the devices of choice for sensors in such applications as tire-pressure monitors, altimeters, pneumatic controls, cable leak detectors, and consumer appliances. Compactness, minimality of power demand, rugged construction, and moderate cost all contribute to making MEMS sensors attractive for instrumentation for future research. Conventional macroscopic flow-measurement instrumentation includes tubes buried beneath the aerodynamic surfaces of wind-tunnel models or in wind-tunnel walls. Pressure is introduced at the opening of each such tube. The pressure must then travel along the tube before reaching a transducer that generates an electronic signal. The lengths of such tubes typically range from 20 ft (approx.= 6 m) to hundreds of feet (of the order of 100 m). The propagation of pressure signals in the tubes damps the signals considerably and makes it necessary to delay measurements until after test rigs have reached steady-state operation. In contrast, a MEMS pressure sensor that generates electronic output can take readings continuously under dynamic conditions in nearly real time. In order to use stainless-steel tubing for pressure measurements, it is necessary to clean many tubes, cut them to length, carefully install them, delicately deburr them, and splice them. A cluster of a few hundred 1/16-in.- (approx.=1.6-mm-) diameter tubes (such clusters are common in research testing facilities) can be several inches (of the order of 10 cm) in diameter and could weigh enough that two technicians are needed to handle it. Replacing hard tubing with electronic chips can eliminate much of the bulk. Each sensor would fit on the tip of a 1/16-in. tube with room to spare. The Lucas NovaSensor P592 piezoresistive silicon pressure sensor was chosen for this project because of its cost, availability, and tolerance to extreme ambient conditions. The sensor chip is 1 mm square by 0.6 mm thick (about 0.039 by 0.039 by 0.024 in.) and includes 0.12-mm (approx.=0.005-in.) wire connection tabs. The figure shows a flow-angularity probe that was built by use of three such MEMS chips. It is planned to demonstrate this MEMS probe as an alternative to a standard tube-type "Cobra" probe now used routinely in wind tunnels and aeronautical hardware. This MEMS probe could be translated across a flow field by use of a suitable actuator, so that its accuracy and the shortness of its response time could be exploited to obtain precise dynamic measurements of a sort that cannot be made by use of conventional tubing-based instrumentation.

Redding, Chip↗

Design and Fabrication of the Langley Aerodrome No. 8 - Distributed Electric Propulsion VTOL Testbed

The Langley Aerodrome No. 8 (LA-8) is a distributed electric propulsion, vertical takeoff and landing (VTOL) aircraft that is being used for wind tunnel testing and free flight testing at the NASA Langley Research Center. The intent of the LA-8 project is to provide a low-cost, modular test bed for technologies in the area of Advanced Air Mobility which includes electric urban and short regional flight. The methods used on the LA-8 provide a rapid means to verify aerodynamic, acoustic, and flight dynamics analysis of new electric VTOL and short takeoff and landing (STOL) designs. In addition, the flight vehicle will be used to help develop test processes for FAA flight vehicle airworthiness certification and for the development of robust flight control algorithms that are tolerant of failures. A new approach is being used on test vehicle design that makes extensive use of 3-D printing. Although materials used in 3-D printing have less strength than traditional materials used for NASA’s wind tunnel and flight models, strategic placement of load-carrying structures allows the aircraft to meet structural criteria while also enabling easy changes to be made in the vehicle design, such as the outer mold line. Modularity of the vehicle’s main components allows rapid changes to the vehicle configuration for comparative evaluation of alternate designs. Finally, a description is given of detailed inertia measurements of the flight vehicle using compound pendulum swing methods.

Urban air mobility↗

Comparison of Wind Power and Load Forecasting Error Distributions: Preprint

The introduction of large amounts of variable and uncertain power sources, such as wind power, into the electricity grid presents a number of challenges for system operations. One issue involves the uncertainty associated with scheduling power that wind will supply in future timeframes. However, this is not an entirely new challenge; load is also variable and uncertain, and is strongly influencedby weather patterns. In this work we make a comparison between the day-ahead forecasting errors encountered in wind power forecasting and load forecasting. The study examines the distribution of errors from operational forecasting systems in two different Independent System Operator (ISO) regions for both wind power and load forecasts at the day-ahead timeframe. The day-ahead timescale iscritical in power system operations because it serves the unit commitment function for slow-starting conventional generators.

17 WIND ENERGY↗

Magnetofluid Simulations of the Global Solar Wind Including Pickup Ions and Turbulence Modeling

I will describe a three-dimensional magnetohydrodynamic model of the solar wind that takes into account turbulent heating of the wind by velocity and magnetic fluctuations as well as a variety of effects produced by interstellar pickup protons. In this report, the interstellar pickup protons are treated as one fluid and the protons and electrons are treated together as a second fluid. The model equations include a Reynolds decomposition of the plasma velocity and magnetic field into mean and fluctuating quantities, as well as energy transfer from interstellar pickup protons to solar wind protons that results in the deceleration of the solar wind. The model is used to simulate the global steady-state structure of the solar wind in the region from 0.3 to 100 AU. Where possible, the model is compared with Voyager data. Initial results from generalization to a three-fluid model is described elsewhere in this session.

Goldstein, Melvyn L.↗

Flux-tube divergence, coronal heating, and the solar wind

Using model calculations based on a self-consistent treatment of the coronal energy balance, we show how the magnetic flux-tube divergence rate controls the coronal temperature and the properties of the solar wind. For a fixed input of mechanical and Alfven-wave energy at the coronal base, we find that as the divergence rate increases, the maximum coronal temperature decreases but the mass flux leaving the sun gradually increases. As a result, the asymptotic wind speed decreases with increasing expansion factor near the sun, in agreement with empirical studies. As noted earlier by Withbroe, the calculated mass flux at the sun is remarkably insensitive to parameter variations; when combined with magnetohydrodynamic considerations, this self-regulatory property of the model explains the observed constancy of the mass flux at earth.

Wang, Y.-M.↗

Multifluid Simulations of the Global Solar Wind Including Pickup Ions and Turbulence Modeling

I will describe a three-dimensional magnetohydrodynamic model of the solar wind that takes into account turbulent heating of the wind by velocity and magnetic fluctuations as well as a variety of effects produced by interstellar pickup protons. The interstellar pickup protons are treated in the model as one fluid and the protons and electrons are treated together as a second fluid. The model equations include a Reynolds decomposition of the plasma velocity and magnetic field into mean and fluctuating quantities, as well as energy transfer from interstellar pickup protons to solar wind protons that results in the deceleration of the solar wind. The model is used to simulate the global steady-state structure of the solar wind in the region from 0.3 to 100 AU. The simulation assumes that the background magnetic field on the Sun is either a dipole (aligned or tilted with respect to the solar rotation axis) or one that is deduced from solar magnetograms.

Goldstein, Melvyn L.↗

Videogrammetric Model Deformation Measurement Technique

The theory, methods, and applications of the videogrammetric model deformation (VMD) measurement technique used at NASA for wind tunnel testing are presented. The VMD technique, based on non-topographic photogrammetry, can determine static and dynamic aeroelastic deformation and attitude of a wind-tunnel model. Hardware of the system includes a video-rate CCD camera, a computer with an image acquisition frame grabber board, illumination lights, and retroreflective or painted targets on a wind tunnel model. Custom software includes routines for image acquisition, target-tracking/identification, target centroid calculation, camera calibration, and deformation calculations. Applications of the VMD technique at five large NASA wind tunnels are discussed.

Burner, A. W.↗

Open Source High Fidelity Modeling of a Type-5 Wind Turbine Drivetrain

The increasing integration of renewable energy resources in evolving bulk power system (BPS) is impacting the system inertia. Type-5 wind turbine generation has the potential to behave like a traditional synchronous generator and can help mitigate the impact on system inertia. A hydraulic torque converter (TC) and gearbox with torque limiting feature are integral parts of a Type-5 wind turbine unit. A high fidelity model of Type-5 wind turbine drivetrain is not openly and widely available for grid integration and transient stability studies. This hinders appropriate assessment of Type-5 wind power plant’s contribution to bulk grid resilience. This work develops and validates a TC model based on those generally used in automobile’s transmission system. Moreover, the concept of torsional coupling is leveraged to integrate the TC and gearbox system dynamics. The entire integrated model will be open sourced and publicly available for grid integration studies.

17 WIND ENERGY↗